Search Documents

By David Pentz, Paul Hodges

GENERAL INTRODUCTION The object of this paper is to discuss those aspects of open pit mine design which are affected by geotechnical factors. The temptation exists for some practitioners of geotechnical engineering to believe that this relatively new engineering discipline is the ‘be all and end all of mining.’ In the opinion of the authors, this is fallacious but, as our ability to put numbers to the behaviour of rocks and soils improves, it is clear that geotechnical engineering will become an integral and important part of designing and operationg mines success- fully. Open pit mines in the context of this paper also includes open cast mines, where the 'ore" is extracted and the waste material is immediately replaced or ' backfilled in the mined portion of the pit. Open pit mines operating today move from very small tonnages a day to in excess of 400,000 tons per day. Several mines are operating and are being designed to capital expenditure for such projects in some cases exceeds five hundred million dollars and in a few cases will exceed one billion dollars. The size of this investment means that financing will have to be provided from banks or joint partnerships. This financial environment means that planning will be carefully scrutinized by experienced representatives of financial institutions or other mining companies. All too often a project has been put in jeopardy because the personal desire of one or two men to make a project proceed has caused incomplete planning or perhaps in some instances deliberately leading observers 'down the garden path.’ In our opinion the day is rapidly arriving when the quality, logic, practicability and completeness of the planning will make the difference between securing financing or not and, in the cases of existing open pit mines, of the difference between survival and closure.

Jan 1, 1977

By Daniel Tempelis, Tom Freeman, Eric Fordham, John Shamma, Steven Duke

The Arrowhead Tunnels in southern California are being completed by MWD under stringent groundwater in?ow limits established by the U.S. Forest Service. Pre-excavation grouting, new TBMs and a bolted, gasketed, pre-cast concrete segment initial lining are employed to control water in?ows. The effectiveness of prescribed water control measures was analyzed using conservative assumptions with the analytical techniques described by Goodman (1964), Heuer (1995), and numerical modeling. Analyses results suggest groundwater in?ows to the tunnels can be maintained well below the limits with aggressive pre-excavation grouting balanced against a reasonable rate of advance and quality erection of the initial lining system.

Jan 1, 2003

By George R. Mitchell

It is a common observation that objects having, different; temperatures exchange energy by radiative transfer. The quantity of radiant energy emitted by an object is a definite function of its temperature. Therefore, a measurement of emitted radiation, by means of a calibrated radiometric instrument, provides a temperature measurement without contacting the emitting object. The physical laws describing radiant energy transfer and their application to remote temperature measurement form the substance of this paper. The energy radiated by bodies having temperatures up to 4000°C is largely in the infrared spectral region. The infrared spectral region is that part of the electro-magnetic spectrum having wavelengths longer than visible light and extending to the microwave region. The wave-lengths range from 0.7 micron (1 micron = 10-4 cm) to 1000 microns. In general, infrared radiometry deals, with the methods of measuring energy flux in the 1 to 15 micron region of the infrared spectrum.

Jan 1, 1960

By O. K. Kuznetzov, L. A. Otrozhdenova, N. D. Malinovskaya, I. I. Maksimov, N. D. Khodov

While processing zinc cakes with application of Weltz-technology silver remains unrecovered and goes into clinker. In order to prevent it the elaboration of effective silver recovery methods from zinc cakes before their weltzing becomes necessary. A combined method of zinc cakes treatment with leaching and flotation in a closed water circuit has been worked out. The technological scheme envisages the use of sulphgydril collectors in combination and comprises a series of consecutive operations: leaching, filtration, precipitation(cementing) and flotation. Total silver recovery is approximately 94%. The technology elaborated has been realized in a project by which the construction of a new shop is under way now.

Jan 1, 1995

By L. G. Kirk

The Mississippi embayment ball clay region, including western Kentucky, western Tennessee, and northwestern Mississippi, accounted for more than 95% of the total U.S. ball clay production during 1985. Other producing states during the year were Texas and Maryland. The U.S. Bureau of Mines reported total domestic production for 1985 of 910,000 short tons. The United States exports approximately 20% of the annual ball clay production. Geologically, the ball clay deposits are sedimentary in origin and occupy the north- eastern flank of the Mississippi embayment. The commercial deposits have been confined to the Claiborne and Wilcox formations within mid to lower Eocene and upper Paleocene age strata. The deposits are lenticular in nature and highly variable in areal extent and thickness. They exhibit very abrupt lateral boundaries and are bounded laterally and vertically by unconsolidated sands, silts, and waste clays.

Jan 1, 1986

By Carl F. Austin

The subject of strata control in mining can be approached from both static or loading concepts or from dynamic or impulsive loading concepts. The fracture process itself appears to be primarily a dynamic process as is the gross creation of fractures through the use of impact, stress wave passage or in more general terms, the use of explosives. This paper presents experimental results which indicate that the understanding of the fracture behavior of rock that has been, established in the open literature is not always appropriate. In particular, the results of this experimental program have shown very interesting differences between the formation of fractures in rock and the formation of fractures in other materials such as metals and plastics which are often used as models for rock behavior studies Fracture patterns and causes of dynamic fracturing in various rock and artificial materials are presented.

Jan 1, 1965

By Dennis Z. Mraz, Maurice B. Dusseault

INTRODUCTION In 1982 and 1983, as part of the mine design program for a New Brunswick potash mine, series of laboratory tests were conducted on potash and salt samples obtained during the mine exploration program. Concurrently, two rock mechanics monitoring programs were initiated in-situ the short term test at site A, and the long term test at site B (figures 1 and 2). SHORT TERM TEST (FIGURE 1) The purpose of this test was to obtain a quick confirmation of laboratory data and comparison of the rock response to excavation with the data available from Saskatchewan potash mines. Instrumentation in the main drift was installed on Day 4 after excavation, and the pressure cells were pressurized on Day 33. The packer type cells in the east crosscut were pressurized on Day 25. Excavation of the west cross-cut was begun on Day 71. This "mine by" test has provided important information required for calibration of laboratory tests, as will be shown later. The test data recorded are shown in a series of diagrams: a. initial room closures, main drift-figure 3; b. convergence graphs, main drift-figure 4; c. stresses recorded, main drift-figures 5 to 8 and, d. stresses recorded, east crosscut - figure15 Three types of instruments were used in this test. In the main drift. Saskatchewan Research Council water type hydraulic inclusions. encapsulated in potash, were used to measure lateral and vertical stresses. In the east crosscut a home-made packer type hydraulic inclusion was used to record radial stresses. The convergence stations consisted of end-grouted bars of reinforcing steel. LONG TERM TEST (FIGURE 2) The purpose of the long term test was to study the steady-state behaviour of a single opening in potash. Site B was placed in a remote area of the mine, well away from any anticipated early mining activities. To assure homogeneity of rock mass, the site was placed within a 30 meter thick vertical limb of a syncline-shaped ore body contained within a 360 metre thick vertical section of salt rocks. It was excavated mechanically as close as possible to the designed square cross-section for the entire length of the room. The square cross- section was chosen in order to achieve a comparable geometry in vertical and horizontal directions; that is, to eliminate any undesired effects of geometry interaction with lithostratigraphy which might have generated non-homogeneous behaviour. The site was extensively instrumented. As in site A, the convergence stations consisted of end-grouted bars of reinforcing steel. However, in order to avoid any measurement inaccuracies which would be associated with the brittle yield zone in the opening walls, bars were placed to the same depth in opposite sides of the opening. This allowed the convergence measurement to be obtained as the absolute convergence between two points, rather than the convergence of a single point with respect to a potentially unstable reference. For stress measurements the Saskatchewan Research Council cells were placed vertically, laterally and radially. Unfortunately, due to cost considerations, it was decided to use a compacted sand, rather than grout, to encapsulate the cells in the boreholes. Due to the extremely small strain rates, only radial ly placed cells could be adequately pressurized. The rest of the cells did not perform adequately, and are currently being replaced.

Jan 1, 1986

By Ahmed Alghamdi, Salem AlGharbi, Aisha AlHarbi, Owain Morton, Norah AlMuhaisen

This paper addresses the challenges in optimizing the phosphate flotation process, specifically focusing on the variability in P2O5 recovery. An artificial intelligence (AI) driven Flotation Prediction Model was developed to accurately forecast P2O5 grades. Leveraging real-time data from various operational sources, the model provides insights into how operators can opstimize key flotation parameters to enhance product quality and recovery rates. The results demonstrate the effectiveness of AI predictive modeling in addressing operational variability, marking a crucial step toward intelligent operations in the phosphate flotation process.

Feb 1, 2025

By Robert C. Edmiston

"Further, we search for the veins by observing the hoar-frosts, which whiten all herbage except that growing over the veins, because the veins emit a warm dry exhalation which hinders the freezing of the moisture, for which reasons such plants appear rather wet than whitened by the frost," Georgius Agricola, De Re Metallica, 1556 In view of Agricola's statement, made in 1556, the concept of using the heat released by oxidizing sulfides as an ore guide can hardly be considered a product of twentieth-century technology. In fact, thermal exploration has received relatively little attention in modern times compared to other potential field geophysical methods. There have evolved, however, two basic approaches to thermal exploration for subsurface heat sources. These are 1) the measurement of surface temperatures by infrared, thermal imagery and 2) the measurement of geothermal gradients in exploratory drill holes.

Jan 1, 1974

By R. S. Shepard

A quick glance at a-portion of the title of this discussion -'Rolling With The Punch" may immediately lead you to assume that I am about to expound on the so-called manly art of self-defense. So that you will not have been misled entirely we will devote our considerations to a far more important art and if I may, I should like to begin by quoting Vincent Van Gogh. According to a literal translation the artist in describing one of his famous paintings said "these peasants are eating their potatoes with those very hands that dug them from the earth' and put them in the dish". Vincent Van Gogh may not have realized at that time, that he could likewise have been describing what is probably one of the oldest of all arts - the art of Material Handling - an art that man with the aid of science has tried to improve since the beginning of time.

Jan 1, 1963

By D. Suarez

The work of engineers responsible for the design and performance of mine facilities is often challenged by economic and practical constraints in the field. Problems have developed in implementing design criteria dictated by persons or agencies not familiar with the dynamic nature of mine engineering. Regional and site-specific conditions frequently require changes to standard designs, or the use of a completely innovative approach, which is not provided for in the regulations. The implementation of engineering design, therefore, usually requires a hard-sell approach to management and regulatory agencies that allows for a happy-medium to all parties concerned. Flexibility on the part of the regulatory agencies is needed to solve operational and environmental problems with sound engineering. Typical hydrologic issues which will be discussed fall in the following general categories: ? Design criteria for sizing water control structures (i.e., culverts, diversion and sedimentation ponds, ditches, etc.) ? Implementation (construction and operation) difficulties ? Regulatory compliance ? Reclamation planning with hydrologic considerations ? Protection of groundwater resources

Jan 1, 1986

By J. F. Fitzpatrick

This paper examines the cost elements associated with changes to gold mining practice over the last decade that result from the changes in environmental regulation and the heightened governmental and public awareness of environmental issues. The main experience base is Pegasus Gold Corporation's flagship mine, Zortman/Landusky, located in the Little Rocky Mountains of Phillips County, Montana. This operation was among the first mines that were permitted under the 1974 Montana Metal Mining Reclamation Act. In 1974, the Montana Metal Mine Reclamation Act was enacted, creating a permit system for metal and industrial mineral mines for the state of Montana. The act established the content of mine permit applications and defined parameters for the reclamation of mining disturbances. The Act can be viewed as implementing legislation for Article 9, Section 2, of Montana's Constitution, which provides that "all lands disturbed by the taking of natural resources shall be reclaimed." Pegasus Gold Corporation's Zortman/Landusky mine was among the first mines permitted under the new Act. In 1978, the initial permit applications were submitted for Zortman and Landusky, and a full Environmental Impact Statement was prepared by the Montana Department of State Lands; permits were issued in 1979. When opened later that year, the anticipated mine life for the combined Landusky and Zortman operations was approximately 18 years, based upon a proven and probable ore reserve of 43.2 million tons. Zortman/Landusky was the first large-scale heap leach gold mine in the United States. Its distinguishing feature was, and remains, a remarkably low ore grade, now .016 oz/ton. The ore is economic because it requires neither crushing nor agglomerating to leach effectively. Approximately two years after the initiation of the state's regulatory process, the Federal Land Policy Management Act (FLPMA) was enacted, establishing a mine regulatory framework for lands under the administration of the Bureau of Land Management.

Jan 1, 1992

By J. S. Orphanos

The requirements for controlling air and stream pollution are a most timely subject for all concerned people. The coal industry has taken great measures to reduce both types of pollution. Through the use of more efficient scrubbing equipment on their thermal dryers, pollution has been considerably reduced. In many cases, the complete elimination of thermal drying by using centrifugal dryers to dewater fine coal products and meet customer specifications has completely eliminated air pollution from this source. To help eliminate stream pollution and the hazards created by tailing ponds, the coal industry is using centrifugal dewatering equipment. Use of centrifugals to dewater fine refuse for disposal would eliminate refuse ponds or extend their life. In doing this effectively and economically, preparation plants have the option of recycling the clarified water to close the water circuit or of discharging the water into receiving streams with the assurance that it contains an acceptable amount of refuse solids.

Jan 1, 1974

By Paolo Prevedini, Antonello de Risi

"The city of Naples has one of the most ancient traditions of tunneling in the world, since Roman age until today. This was due to the softness of volcanic rock covering most of the city surface, this determined in centuries the excavation of many connected cavities, today still accessible. The building of metro lines promoted industrial tunneling construction: TBM, Raise Boring Machine, Vertical Shaft Machine and freezing technologies played a decisive role facing water pressure near the sea. MNspa is an advanced constructor with two lines built in parallel, mainly underwater. The planning of this infrastructure has been upgraded with the projects of international architects from all Europe, with installation of art masterpieces in station spaces while archeological excavations revealed artifacts since Paleolithic. The city expects to give a new image of the urban landscapes within the completion of all stations and consequent rehabilitation of interiors and external city spaces. A case study of Municipio square station, is chosen to explain the relevance of archaeological research in improving and developing the projects of Line 1 stations. In these pages, it will be explained how the engineering process required to deal with Art, Architecture and Archaeology to finally realize an extended urban renovation of Naples. 1 CITYSCAPE 1.1 Introducing the geological history of Naples In the evolution of the city, capital of the Magna Graecia and of consequent kingdoms, a new layer of buildings was added over the foundations of demolished walls of the precedent domination period: from the top of the Bourbons layer (the most common scenery of the city since 1734) to the Aragonese layer found just underneath it; then below stands the Angiovin city, which in turn is built above the Swabian traces; underneath the ancient traces of the Byzantine age are found just above the extended Latin age layer. The most ancient settlement, known as Parthenope, dates back to 1500 b.C. It sits below the Greeks remains of the city of Palepolis, which had been rebuilt under the name of Neapolis by Romans."

Jan 1, 2016

By Neal P. Cochran

The United States is faced with increasing demands for electricity, coupled with continuing demands for crude oil and gas. Superimposed on these' national requirements are our national requirements for clean air and elimination of thermal pollution of our rivers. From the coal viewpoint, this situation is complicated still more by the rapid advances in nuclear power. In this paper, I hope to show a way to use our Western coals as a solution to this involved national problem by producing: 1. High quality crude 2. Low cost power 3. Economic byproducts We could expect these products to be made at one site in an integrated plant that would mine (extract) coal, process it, and convert it to electricity. Perhaps the most important attribute of the plant is its reduced water requirement and the elimination of air pollution from the power cycle. Quite logically, such a plant would probably recover valuable byproducts, such as pipeline gas, sulphur, cement, aluminum, and the like. Although the plant projected in this paper is a conceptual one, it is based on work now underway by Government and industry. Prediction of the future is a most hazardous occupation, but plants such as the one projected are based on current knowledge and can be expected to reach commercial operation in the near term future.

Jan 1, 1967

By C. H. Cox

The Alumet Company of Golden, Colorado, is currently engaged in the development of their Diamond Creek and Lanes Creek phosphate ore bodies located near Soda Springs, Idaho. The Alumet Company is a partnership of National Steel, Southwire Co., and Earth Science Inc. Davy Powergas, Inc., of Florida was contracted by Alumet to perform an evaluation study of these properties and, in general, determine the tonnage of altered and unaltered phosphate reserves which would be amenable to beneficiation and production of merchantable phosphate rock (defined as material with a P2O5 content of 3 1.0% and greater). The Colorado School of Mines Research Institute was retained by Davy Powergas to develop a beneficiation method for the studies of the altered and unaltered ores. Ore reserves were classified by Davy in a comprehensive range of categories such that any partial grouping could be made as dictated by future mine planning, mine or mill design, or prevalent economic conditions. Categories included ore horizon, stripping ratio, degree of certainty of their existence, and physical and chemical characteristics. The last category was of interest for beneficiation considerations in that it dealt with the degree of alteration of the phosphate ore.

Jan 1, 1979

By S. P. Singh

In order to understand the intricate nature of blast damage mechanism and to counter the associated problems, small scale blasting experiments were performed on hydrostone, concrete and granite. This was followed by a 2.4 m x 2.7 m (8'x 9') drifting operation in a quartzite quarry. Interior as well as exterior damage was assessed by different techniques. On the basis of the experimental results, the effect of explosive characteristics on the damage was examined.

Jan 1, 1992

By Alexander Sutulov

It is calculated that since the beginning of last century, which practically coincides with the beginning of the Industrial Revolution, our civilization has consumed around 239.5 million tons of copper (see: Table 1). According to the most pessimistic projections of today, with only a 2.5% annual growth rate in demand, we are bound until the end of this century to consume another 200 million tons of copper in remaining 17 years. A recent study made by US Bureau of Mines (1) indicates that the proven ore reserves of 150 major operating mines and about 120 deposits sufficiently explored for development and feasibility studies accumulate a total mass of 49.3 billion tons of ore, assaying an average of 0.82% Cu and containing around 324 million tons of recoverable copper. Consequently, there is a high grade of probability that the bulk of our future ore supplies, for our demand of, say, next 25 years will cane precisely from these mines. The interesting point in USBM study is that it indicates the recoverable byproduct content of these ores and which is: 118.2 million troy ounces of gold 2277.4 million troy ounces of silver 7.1 million tons of lead 24.7 million tons of zinc 1.3 million tons of nickel 3.1 million tons of molybdenum 765 thousand tons of cobalt, and 720 thousand troy ounces of platinum. This information gives us a relatively reliable profile of our future ores for next 25 years, and thus makes possible evaluation of byproduct credits in our future copper mining and producing activities.

Jan 1, 1983

By Susan T. Bagley, Kenneth L. Rubow, David H. Carlson, Bruce K. Cantrell, Winthrop F. Watts

Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol. The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment. The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3 with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location. In three of the mines filter samples were collected for DEAassociated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, C02, NO, NO2, and SO2, were well below regulated levels. INTRODUCTION Diesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992). The U.S. Bureau of Mines has collaborated with the University of Minnesota to develop and field test a PDEAS. The PDEAS is a three stage sampler based on the MSA' personal respirable dust sampler. It utilizes a respirable cyclone preclassifier followed by a 0.8 µm cut point impactor and afterfilter operating at a flow rate of 2 L/min. Respirable aerosol greater than 0.8, µm in size is collected by the impactor while DEA, less than 0.8 µm in size, is collected by the afterfilter. Hence, gravimetric analysis of the afterfilter permits measurement of DEA concentrations. This development and laboratory evaluation of the PDEAS were described previously by Cantrell (1990) and Rubow (1990). During field tests of the sampler, numerous air quality measurements were made in continuous miner sections of five underground coal mines that use diesel haulage equipment. These air quality measurements included levels of selected PAH and biological activity associated with DEA collected in the intake and haulageway areas of three of the five underground mines, and CO, CO2, NO, and NO2 in two of the mines. The objectives of this paper are to present the DEA and associated pollutant concentrations measured in these mines and to assess the impact of diesel face-haulage equipment on underground mine air quality. MINE DESCRIPTIONS The mines used for the PDEAS evaluation were designated J, K, L, N, and 0. Mines K, N, and 0 are located in the Western United States, while mines J and L are located in the East. Each mine produces high volatile, bituminous coal with shift production levels varying from 500 to 2000 tons/section. Seam heights varied from 1.5 to 3.0 m. Mines K and N use continuous mining to develop longwall panels. The others are strictly room-and-pillar operations using continuous miners. The number and types of diesel-powered vehicles used at these mines were described by Watts (1992b). Mines J, K, N, and 0 use diesel power to assist in a wide range of activities in addition to coal haulage. These included road maintenance, personnel and materials transport, lubrication, and welding. Mine L used only three diesel-powered shuttle cars to haul coal. SAMPLING AND ANALYSIS METHODS Aerosol Measurements Aerosol samples were collected in the mine portal area, the clean air intake to the continuous miner section, the haulageway one crosscut inby from the feeder breaker and belt, in the return airway, and on selected personnel. The haulageway sampling site was located near the point where the diesel-powered shuttle cars turn around to dump their loads. Additional respirable and DEA samples were collected and have been reported by Haney (1990).

Jan 1, 1993

The heat of immersion of coals in different immersional liquids is measured as a function of particle size and moisture content. Decrease in particle size shows a concomitant increase in the heat of immersion. The heat of immersion is dependent upon the nature of immersional fluids. In addition the nature of moisture present in coal influences the heat of immersion.

Jan 1, 1993