Search Documents

By Chris Chmura, Ketut Karmawan, Ian J. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of West Papua, Indonesia. Present production from PTFI’s DOZ Underground Block Cave Mine is approximately 40 thousand tonnes per day (ktpd). This paper describes the design process and recommended ventilation infrastructure necessary to expand the DOZ Mine reserves and to increase sustained daily production above 50 ktpd. The enlarged footprint will feature longer production panels of up to 650 m in length, more active draw points, a second large gyratory crusher, and additional men and mobile equipment. The increased ventilation capacity will be achieved through the development of new, dedicated ventilation drifts, and primary Underground exhaust fans.

Jan 1, 2005

By S. C. Libby

The amount of fine material (minus 60 Tyler mesh) generated during calcination and/or handling of calcined abrasive grade bauxite from Alcoa's operations at Moengo, Suriname, has recently increased relative to past production experience. Bulk samples of raw abrasive grade bauxite from three deposits in the Moengo area have been studied in order to determine the factors controlling the generation of fine material samples from the Jones IC and Tapira deposits, which generate excessive amounts of fine material, have been compared with reference samples from the Begi Gado deposit, which does not generate excessive fine material. Additional type samples of abrasive grade and marginal abrasive grade bauxite from deposits in the Moengo area which represent different bauxite textures found in the Jones IC, Jones I, and Begi Gado deposits have also been studied. Field observations in the Moengo area have indicated that abrasive grade bauxites with a dull, earthy appearance generally do not generate excessive fines. On the other hand, excessive fines are generally associated with coarsely crystalline bauxite in which the gibbsite crystals appear to sparkle in sunlight.

Jan 1, 1980

By Mehmet Guney

[The Atlantis-II-Deep is a hydrothermal mineralization located along the median valley of the Red Sea at a water depth of about 2200 m. Extensive exploration of the metal-rich brine deep revealed a potentially mineable deposit on economic interest consisting of oxides, silicates and sulphides with considerable concentrations of zinc, copper, cadmium and silver. Geostatistics was applied to assess the most likely in-situ vague of the metal potential for economical exploitation. Semi-variograms were constructed to characterize the structure of the regionalized distribution of the geological parameters. Volume grades and thicknesses were determined by the kriging technique, avoiding systematically biased high or low grades, and then block .tonnages were computed. The estimation variances, distribution of errors and histograms of observed and kriged values in each grid Mock were also produced.]

Jan 1, 1983

By A. I. Makhin, S. M. Sablukov, V. K. Sobolev, V. A. Larchenko, V. S. Shchukin

The kimberlites of northern Europe are related with a large crustal block having a northwest-southeast orientation. Kimberlites penetrate the Archean formations of crystalline basement, Late Proterozoic rocks, which are overlapped by Middle Carboniferous and younger deposits. The kimberlites bodies include pipes, dikes and sills of Upper Devonian age. Within the region, rocks of two magmatic series form diamond-bearing kimberlites. Aluminum rocks form a new type of diamond-bearing rock that is not found in other diamond provinces. Kimberlites of this region are characterized by highly developed deuteric alterations, a low content of associate minerals, the presence of two diamond generations and an increased content of jewelry-grade diamonds.

Jan 1, 1997

By S. K. Kawatra

In order to meet federal air pollution guidelines, it is necessary to remove a considerable quantity of sulfur from many North American coals. This may be accomplished by oxidizing the sulfur to water soluble forms, followed by washing the coal. Selective oxidation of the various sulfur forms can be accomplished through the use of a variety of types of bacteria. In this paper, the various bacteria and their requirements are described, and processes using bacteria to remove coal sulfur are discussed.

Jan 1, 1987

By D. A. Stanley, B. J. Scheiner, P. M. Brown

The Bureau of Mines (USBM), US Department of the Interior, has developed a method of dewatering clay slurries based on flocculation by high-molecular-weight polymers and water removal from the formed flocs using a trommel or hydrosieve. The exchange ion on the clays affects their dewaterability. Metal ions in solution and on the exchange sites of smectite clays are known to act as Lewis acids. Recent work has determined that these ions can be titrated with high-molecular-weight polymers. The relative acidity of the exchange ion and the basicity of the polymer determined by the new method give insight into the dewatering mechanism.

Jan 1, 1990

By W. G. Lacy

Anticipation of problems and the adoption of corrective measures in the design of engineering structures, establishment of pertinent building codes, and urban planning and zoning to obtain optimum land usage and conservation of natural resources demands a thorough understanding of geological conditions of a developing urban area. In the and to semi-arid southwestern United States erosional and depositional processes result in special situations that require special precautions in building practices. A series of studies currently underway in the Tucson area prompted by foundation failures and breaking, of buried service lines serve to illustrate some of these relationships between the geological environment and history, and engineering problems.

Jan 1, 1963

By J. Harrison Daniel

Increasing concerns of industrial hygiene and worker health issues and resulting regulatory actions, coupled with continuing advances in mining systems, are placing new burdens on the industry and Federal Government; particularly, mine ventilation departments. More encompassing worker health programs are required to respond to Federal promulgation of regulations and to keep abreast of techno- logical advances in the mining industry. The relationship between the mining industry and Federal agencies involved in rulemaking is presented, along with the rationale of an Industrial Hygiene Management Plan. This plan or strategy focuses on developing partnerships and collaborative research groups to address the controversial health issues facing not only the mining workforce, but our society.

Jan 1, 1993

By Allen Pratt, Guy Deschênes, Mike Fulton, Hai Guo

Calaverite is a gold telluride species, with the composition, AuTe2. Calaverite is usually characterized by an exceedingly slow dissolution rate in a cyanide solution. Cyanidation of a slurry containing synthetic calaverite (P90 of 10 microns) was studied to determine the leaching kinetics and surface reactions. Alkalinity, dissolved oxygen, lead nitrate and sulphide minerals (pyrite and chalcopyrite) were among the parameters evaluated. The reaction products at the surface of calaverite were documented using X-ray photoelectron spectroscopy. High lime concentration with lead nitrate and injection of oxygen produced the fastest leaching rates. New gold leaching mechanisms were identified which appeared to be related to the parameters selected.

Jan 1, 2005

By M. Zhang, H. Ni, F. Zheng, M. Guo

"In the present work, we investigate the effects of roasting temperature and time on the transformation of the titanium (Ti)-bearing phase and magnesium aluminate spinel (MgAl2O4) phase in Ti-bearing electric arc furnace molten slag during the molten sodium hydroxide (NaOH) treatment process. With applied temperature of 700 °C for 60 min, and a mass ratio of Ti-bearing electric arc furnace slag to NaOH, or Rslag/NaOH, of 1:1.2, the conversion ratios of the Ti-bearing phase and the MgAl2O4 phase reached about 98.3 percent and 88.1 percent, respectively. Moreover, investigation of the reaction kinetics indicate that the conversion of these phases during the molten NaOH treatment process is a typical solid-liquid reaction, and it can be theoretically described by the unreacted shrinking core model. The conversion ratio of the Ti-bearing phase was found to be controlled by the chemical reaction step, with an apparent activation energy of 41.76 kJ/mol. The decomposition of the MgAl2O4 phase was found to be controlled by the surface chemical reaction in the early stage of 0 to 20 min from start of reaction, changing to diffusion control in the later stage of 20 to 60 min. The apparent activation energies of the process were determined as 55.88 and 22.72 kJ/mol, respectively.IntroductionChina has rich mineral resources of vanadium–titanium magnetite ore deposits, and the iron and steel industry in the country produces millions of tons of titanium (Ti)-bearing slag every year. The problem of how to dispose of the Ti-bearing slag has attracted much attention, and various approaches have been developed, including the acid process (Li et al., 2007; Zhang et al., 2011; Zhang and Nicol, 2010; Li et al., 2011), alkali fusion process (Han et al., 2012; Middlemas, Fang and Fan, 2013; Nayl, Awwad and Aly, 2009; Lasheen, 2008; Zhang, Qi and Zhang, 2009), carbonization and chlorination process (Liu et al., 2008; Tao et al., 2012; Fu et al., 2012; Liu, 2009), selective crystallization process (Lei and Xue, 2008; Li et al., 2011; Zhang et al., 2007a, 2007b). However, these processes have been beset by various functional, economical and ecological problems (Yu and Chen, 2010). With environmental protection regulations becoming increasingly rigorous, and demand growing for the comprehensive utilization of resources, the focus is on methods to treat Ti-bearing slag with high efficiency and mild reaction conditions (Nazari and Riahi, 2011; Wu et al., 2013)."

Jan 1, 2017

By J. R. Walls

Mining is one of world's oldest industries. Its rich history continues into modern times. The Waste Isolation Pilot Plant (WIPP) located in southeastern New Mexico is writing the next chapter in mining history. In fact, WIPP technology is the key to closure of the nuclear cycle with the disposal of nuclear waste in a deep geological repository. It might seem odd that the age-old institution of mining would be linked to the problem of nuclear waste disposal. In fact, the nuclear industry would not exist without mining. Uranium ore is mined from either underground or surface mines as the initial step in harnessing the magnificent resource of nuclear energy.

Jan 1, 1996

By R. Schuerch, C. Cimiotti, M. Piemontese, N. Karlin, P. Perazzelli, P. Halton

The new Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to White Point Manifold. The tunnel will be approximately 7 miles (11 km) long with a finished internal diameter of 18 ft (5.5 m). The TBM is designed to cope with high water pressure up to 10 bar. The geotechnical challenges are due to the heterogeneous subsurface conditions: in the first half of the alignment, the tunnel runs through soils with a low overburden under urban areas, and, in the second half, the tunnel runs through extremely weak, intensely faulted rock masses with high overburden. Following an overview of the project, this paper focuses on the northern portion of the alignment and presents a decision-making procedure developed during pre-excavation phase in order to cope with the expected heterogeneous conditions during mining. The risk assessment and the TBM operational design of the southern portion will be dealt with in a future paper.

Jun 13, 2023

A Mineração da Trindade (Samitri) is a major Brazilian iron ore producer. Founded in 1939, privately owned Samitri operates six mines with a total production capacity of 14.5 Mt/a (16 million stpy). The mines are located in southeastern Brazil in the state of Minas Gerais. They are operating in the iron ore quadrangle, Brazil's primary iron ore-producing region. In addition to iron ore production, Samitri has the capability to produce 350 kt/a (386,000 stpy) of ferruginous manganese ore from two mines, also located in the iron ore quadrangle. Historically, about 70% of Samitri's production of lump ore, sinter feed and pellet feed is exported. Destinations include Belgium, Luxembourg, France, Germany, Trinidad and Tobago, China, Turkey and the United States. Alegria Mine In September 1989, Samitri started a new processing plant to treat itabirite, a low-grade iron ore. The goal of the plant was to produce sinter feed (coarse fraction) and pellet feed (fine fraction). Primary separation of sinter feed from pellet feed was accomplished with conventional vibrating screens making a 0.4-mm (40-mesh) cut. The screen oversize was stockpiled as sinter feed. The undersize was deslimed with hydrocyclones and upgraded by conventional froth flotation. Resulting pellet feed grades ranged from 3% to 3.5% Si02. A change in pellet feed requirements by Samarco Mineração SA, a Samitri subsidiary, called for Si02 levels below 1 % and increased production levels. Moreover, market demands called for a change in sinter feed size distributions. Unfortunately, lower pellet feed Si02 levels could not be achieved with the existing process. This was because of the presence of 35% +0.15 mm (+100 mesh) in flotation feed. Flowsheet development. Laboratory and pilot-plant studies conducted at Samitri's research facility found that to achieve lower Si02 levels, the +0.15 mm (+100 mesh) in flotation feed must be kept below 5% to 10%.

Jan 1, 1997

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

By Sibley C. Burnett

Early attempts to apply superconductivity to the beneficiation of kaolin required very large refrigerators to remove the heat generated during rapid charging and discharging of the magnet. In the early 1990's, Advanced Cryo Magnetics, Inc. developed and patented methods to reduce this pulsed heating by a factor of fifteen. Small, helium refrigerators and cryo-coolers are now used. Along with savings in electric power, superconductivity allows operation at higher magnetic fields and greatly improves separation process efficiency. New designs offer enormous reductions in weight, size and capital cost as compared to older copper magnets. Application of this technology to minerals other than kaolin is emerging.

Jan 1, 1999

By J. E. Powell

Introduction The disposal of mine tailings, development rock, and other unwanted refuse material underground in mines by using pneumatic conveying techniques has been undertaken in the coal industry for many years. Similar equipment has been utilized for backfilling hard rock mines and is currently being applied in a gold mine in South Africa where development rock is being stowed in the mined-out stopes to help reduce the incidence of rock outbursts. On a limited scale, pneumatic conveying has been applied for backfilling uranium mines and one particular mine in New Mexico, U.S.A., has used this technique for 8 years. Other uranium mines in this area are now considerinq the dry backfill technique to eliminate the problems associated with hydraulic fill. The need to backfill in uranium mines is primarily of importance to improve ventilation, stabilize the pillars and roof, and possibly to extract a larger percentage of the uranium ore. If this can be achieved by utilizing the tailings from the beneficiation plant and using rock from the development headings which in itself may be slightly radioactive, then a greater benefit can be derived. Backfill can be achieved with hydraulic fill methods by running slurry into the stopes and allowing the water to decant and return through the footwall development entries to sumps for pumping to the surface. However there are several disadvantages associated with this method in that water is percolating throough the mine workings; it is necessary to build bulk heads in flat lying deposits; it is difficult to fill right to the back; and the decanted water takes with it quantities of the finer sand particles which results in maintenance problems with the mine pumps. Pneumatic conveying can overcome these problems in that the voids can be completely filled with high degree of compaction, heavy bulk heads are not necessary, the development rock can be added to the pneumatic system for disposal underground so eliminating hoisting cost to the surface, and cement can be added to the wetted material. To

Jan 1, 1980

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture properties of a number single and multiphase brittle materials has been investigated. The reduction in the impact fracture energies and particle strengths with and without pretreatment has been measured in precise single-particle experiments using the Ultrafast Load Cell. Variations in the fragmentation pattern caused by different pretreatments were assessed by measurements of the progeny size distributions. The differences in the effect of thermal treatment on single and multiphase materials are discussed based on the experimental results.

Jan 1, 1995

By Richard R. Klimpel

INTRODUCTION Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Froth flotation is a physico-chemical process for separating finely ground minerals from their associated gangue material. The process involves chemical treatment of a finely divided (ground) ore in a water pulp to create conditions favorable for the attachment of certain of the mineral particles to air bubbles. The air bubbles then carry the selected minerals, called valuable, to the surface of the pulp to form a stabilized froth which is removed and recovered. The unattached gangue material remains submerged in the pulp and is either discarded or reprocessed. To obtain the adherence of the desired mineral particles to the air bubbles, at least two specific steps must occur: a hydrophobic (water hating) surface film must be formed on the particles to be floated along with a hydrophillic (water wetting) film on all other particles; and a controlled bubble surface tension interface must be maintained, allowing for high particlelbubble collision frequency and efficient attachment or sticking of the particle to the bubble once collision has taken place. In most flotation applications, the above two steps are controlled by chemical flotation reagents. The collector is a chemical reagent which produces the hydrophobic film on the valuable mineral particle and is the primary driving force that initiates the flotation process. The frother is a chemical reagent which influences the collision frequency and attachment efficiency of hydrophobic particles and air bubbles. Thousands of research papers and books have been published on the chemical theory behind sulfide mineral collectors, e.g., Fuerstenau (1962), Fuerstenau (1976), Fuerstenau, et. al. (1985), King (1982), Leja (1982) and Moudgil and Somasundaran (1987), This article will only address and summarize some of the more practical aspects of collector usage. The industrial scale practice of froth flotation in sulfide mineral concentration has changed little since the 1950's. For example, of the approximately 80,000 metric tons of sulfide mineral collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago. A very interesting and informative history of collector development has been given by Crozier (1984). In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920's with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years. As a result of the above environment which makes reagent cost/performance analysis difficult for new reagents, there is a strong tendency for the flotation operation to use, and reagent companies to supply, as cheap as possible raw materials and manufactured products that are quite general in application. In the last 20 years or so, there has been increasing technical effort to tailor make reagents for specific applications, but to date such work has had little commercial impact. It is clearly the hope of this author and others that this situation will change in future years as technology improves and pressure for improved flotation performance intensifies. This article is a condensation of collector usage trends quantified as part of a comprehensive industrially oriented applications program on froth flotation organized by Klimpel and coworkers (1979-1987) and as reported in various countries that participated in the program from 1978-1983. No attempt will be made to provide specific.

Jan 1, 1986

By Don Opacic

The disposal of sludges and other similar industrial wastes is a major problem. Liquid wastes from industrial operations, when treated, produce significant volumes of sludge which are difficult to dispose of, because of the chemical and physical properties of the sludge. In the mining industry sludge is produced from various water treatment operations, in particular mine drainage neutralization. Waste water from coal preparation plants also produces a sludge however the sludge is in fact a slurry containing clays, coal fines and coal impurities. In many areas the disposal of these sludges is producing a serious problem. Mine drainage sludge consists of a variety of hydrous iron oxides, usually ferric oxides, contaminated with other neutralization products such as calcium sulfate. The volume of sludge from mine water or mine

Jan 1, 1973

By Yukika Miyashita, Takahiro Inoue, Kenji Namikawa, Masashi Matsumoto, Junichi Koseki, Yoshihiro Terashima

"In order to construct an underground two-layer expressway branch junction structure with a height of 14.7 m and a width of 22.3 m, two shield tunnels in each layer were combined by using a non-cut-and-cover enlargement method in sedimentary soft rock. Before and during the construction work, preliminary analysis, in-situ investigations and laboratory tests were conducted to ensure the construction safety and to evaluate the deformation characteristics of sedimentary soft rock. The construction project was safely executed without any water leakage or collapse of tunnel working face. The predicted results from preliminary analysis were almost similar to the measured values. From the detailed investigation of measured results, it was confirmed that the deformation characteristic of the sedimentary soft rock was observed to a small extent as the ground deformation derived from construction work. INTRODUCTION In recent years, some newly constructed urban expressways in Japan are being planned as underground structures due to the consideration of roadside environment. The construction of such underground expressways is frequently conducted using a shield tunneling, a typical one of non-cut-and-cover methods, to prevent any adverse effect to traffic in arterial roads, operation of nearby commercial establishments, and daily lives of local residents during construction work. For underground urban expressway, the connections with existing road network on ground surface or on elevated sections are indispensable, which require the construction of an underground branch junction with large cross-section. This raises a technical difficulty regardless of the open-cut or non-open-cut construction method."

Jan 1, 2016