Search Documents

By L. Michael Kaas

Any increasing number of restrictions are being placed on mining management's ability to pursue profit. Raw materials pricing, the cost of capital equipment, labor cost, and overhead costs, are becoming more difficult to control. Cost reduction is one of the few remaining areas in which management may still exercise its profit making ability. Equipment maintenance is an area where mine and mill management can readily reduce costs and increase profits. Why is this possible? First, maintenance costs comprise a large portion of total operating cost. Thirty to sixty percent of the operating cost dollar is not unusual. Even a relatively small percentage reduction in this cost represents a very sizeable increase to mining profitability.

Jan 1, 1967

By Thomas J. Peters

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral investigation of about 85,470 acres of the Diablo Mountain Wilderness Study Area, to determine mineral resources and mineral resource potential. The study area is in Lake County Oregon, about 45 miles northwest of Lakeview. Fieldwork was conducted in 1986, 1988, and 1989. Geologically, the study area lies on the northwest edge of the Basin and Range physiographic province, a region of fault block-formed mountains and basins characterized by interior drainage. Consolidated rocks are mostly Tertiary basalt and tuffaceous sedimentary rocks. Low-lying areas are covered by Quaternary alluvial-fan, sand-dune, playa, lacustrine, and landslide deposits. The principal structural features are normal faults that have large vertical offsets; these faults are typically concentrated at the margins of large horst and graben. The 34,310-acre "additional," or western part of the area was mainly studied in 1988 and borders the east shore of saline Summer Lake. In this portion of the study area there is potential for undiscovered resources of soda ash, boron compounds, and sodium sulfate as well as by-products, which include magnesium compounds, salts, potash, bromine, lithium, and tungsten associated with brines. No energy or mineral resources were identified in the study area, but brines within lake and playa sediments contain concentrations of chemical components suitable for the production of soda ash, boron compounds, and sodium sulfate. Possible by-products include potash, salts, bromine, lithium, magnesium compounds, and tungsten. Limestone from the study area could be used in the recovery process of brine components or agricultural uses. The study area includes thermal springs and lies within 2 miles of the Summer Lake Known Geothermal Resource Area. Local production of geothermal power by the binary process may be economically feasible. Soda ash, soda ash products, and boric acid are widely used in fluxing metals, and have important applications and markets in the aluminum industry in the northwest and the developing Chinese counterpart. Evaporite commodities are essential to many "backbone" industries, and to many new applications and advanced materials. Markets for brine mineral products appear to be undergoing steady and strong growth, especially in the Pacific Northwest and in Pacific Rim countries. Soda ash produced near the study area would be 55 percent closer by rail to marine export at Portland, Oregon, than trona deposits of the Green River District (Wyoming). Soda ash and a daughter product, caustic soda, and sodium borohydride will receive increased application in the bleaching of paper pulp for environmental reasons. Caustic soda, used in many industrial processes, is more environmentally friendly when derived from soda ash than when produced from sodium chloride salt, because of the absence of a chlorine by-product. Producing soda ash from brines, a type of in situ" mining, can be done with minimal environmental degradation, and mining natural soda ash is environmentally as well as economically preferable to synthetic soda ash production.

Jan 1, 1995

By L. D. Hartzog

A pilot plant investigation of a semi-autogenous mill - ball mill circuit is described. The plant was operated with minus eight-inch diabase as feed material to the semi-autogenous mill. The semi-autogenous mill recycle screen underflow was put to a ball mill in closed circuit with a cyclone. An operating Work Index of 13.3 to 14.9 was obtained with the pilot ball mill. This Index is substantially in agreement with the scalped feed laboratory Work Index for 15.3 for recycle screen underflow. The Bond Index of the diabase was 15.8. Thus, one may use the scalped feed laboratory Work Index to size semi-autogenous grinding plant ball mills.

Jan 1, 1974

By A. K. Sinha

Inspite of the growing demands worldwide, thermal coal must compete in the market both in price and quality. The design and performance efficiency of coal preparation plants is thus crucial to the survival and profitability of a coal industry. While the coal recovery influences the cost of production, the quality produced by a preparation plant determines the selling price. Several coal preparation plant simulation models have been developed in recent years to help Improve the performance of coal preparation plants. A research project was recently conducted at Southern Illinois University to evaluate the practical applicability of such a model. The results of this study are presented and discussed.

Jan 1, 1986

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016

By Theodore Balberyszski

The gradual depletion of high-grade sulphide mineral deposits has turned the attention of the mineral industry to the recovery of metals from the oxides and silicates. Anionic (fatty acid) and cationic collectors have in some cases made flotation of non-sulphides possible, although in general, flotation of oxide ores is not as yet an economic process. Consequently, many attempts have been made to sulphidize the surface of the relevant oxide mineral and thus make it amenable to flotation. (1) (2) (3) In recent years, Bautista and Sollenberger(4) have investigated the conversion of a number of oxides to sulphides by reacting them with molten sulpur. This paper presents the results of investigations carried out at the School of Mineral and Metallurgical Engineering at the University of Minnesota to study the flotation characteristics of some sulphidized minerals. It is divided into two parts; Part I describes the sulphidization of a number of oxides and a silicate, and Part II presents the flotation behavior of the products of sulphidization.

Jan 1, 1968

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By Erkan Bozkurtoglu

The most important difference between weathering and alteration, which are the definition of the change in rocks that occur with the help of physical and chemical effects, is a new product is formed as a result of alteration. Although atmospherical conditions are the most important factor during rock change, geothermal fields play a large role in the developing of alteration phenomenon. Because every geothermal system shows different characteristics including the chemistry of geothermal fluids and their potential applications, alteration on the field is important for the studies to find geothermal energy sources and to obtain the thermal fluids. The development of weathering and alteration which is the mark of interaction , between the physical and chemical properties of geothermal fluids and gases with the reservoir and wall rock, gives out important data about the hydrogeology, hydrology, reservoir conditions and characteristics of reservoir rocks of the geothermal field. Therefore defining the development of weathering and alteration phenomenon in a geothermal field and modeling the change in rocks, is very important for the benefication of the geothermal field economically. In this study 70 km2 that reside between Kösedere plains, Uzunburun, Çamtepe, Centirler villages in Çanakkale - Ayvacik - Tuzla geothermal field were studied and subsurface travel of saline thermal fluids and their interaction with the rocks and development of weathering and alteration phenomenon in the field were investigated. For this purpose geological mapping of the field were done and observations and measurements as well as rock sampling were carried in locations more than 220. As the result of petrographical investigations of rock samples development of weathering and alteration phenomenon were defined and 16 rock samples out of 220 that represent the field in general were chosen to be chemically analized and after that geochemical comments on the Tuzla geothermal field were made. Also hydrothermal alteration zones that are located in Tuzla Tepe, on which weathering and alteration phenomenon is observed as widespread and thermal water discharge locations in the near perimeter of Tuzla Tepe were mapped and from these data rock change in Tuzla geothermal field were modeled.

Jan 1, 2005

By L. Alan Weakly

This paper was presented at the ‘17th U. S. Symposium on Rock Mechanics’ on August 29, 1976, at Snowbird, Utah, at the SME-AIME Fall Meeting on September 1, 1976, at Denver, Colorado, and at the Polish-American conference on Ground Control in Room-and-Pillar Mining on August 7, 1980 at Southern Illinois University, Carbondale, Illinois. Introduction The purpose of this paper is to present a viable method of reinforcing rock pillars by utilizing fully grouted reinforcing steel and a cement- fly ash mortar. Although the fully bonded bolt concept is not new as exemplified by the present widespread use of resin bolts within United States mines and by the use of cement grouted reinforcing used as back pins in the Kiruna Iron Ore Mine in northern Sweden, (1)(2)the method of stabilizing mine pillars with fully bonded reinforcing is new. This method, called the "grout-rebar system", was first incorporated at St. Joe Minerals Corporation's Fletcher Mine in December of 1972. The system was used on an emergency basis before extensive research on the mechanics of the system could be completed. Since Decmeber of 1972, however, approximately 206 pillars have been reinforced at Fletcher and the system is currently being used on a regular basis at two other St. Joe mines and at two competitor mines in the area. Basically, this paper is a case study of the efforts, research and results of utilizing the grout-rebar system, on a selective basis, at the Fletcher Mine. In addition to information about the system, this paper will explain in detail the three rock mechanics instruments developed by St. Joe and used to measure and monitor rock movement to validate the group-rebar system.

Jan 1, 1982

By K Timtner

As shown in former publications there are problems in load sharing of backstops in multiple drives of conveyors. Therefore, detailed calculation methods and design recommendations are required. In this paper various designs of load sharing methods are described and a dynamic torque calculation method will be presented. With this method the loadsharing properties for low and high speed backstops are calculated and compared. These properties depend on the spring characteristic of the drive train between backstop and load. Furthermore, the properties depend on the method of torquearm support and shock absorber configuration. Remarkable differences for external and internal backstops are shown

Jan 1, 1998

By M. P. Fahey

A significant amount of silca is recovered in the rougher stage of anionic flotation of Florida apatite. This recovery, in the past, has been attributed to both entrainment and cation activated flotation. This study shows that by using a transport factor, it is possible to determine the contribution of each mechanism towards silica recovery. Further, it is shown that the concentration of cations in the conditioning water significantly affects both the amount of silica recovered due to entrainment and true flotation. Further confirmation of this phenomenon was obtained by Ca++ doping of the conditioning water and by using a sodium silicate depressant.

Jan 1, 1996

By G. A. Kordosky

The literature contains several references to the influence of copper solvent extraction reagents on crud formation, but, there is disagreement as to whether the reagent has an influence on crud generation. The results of three pilot plant campaigns, where crud generation was studied as a function of the copper solvent extraction reagent, are reported. These pilot plants were run at operating copper solvent extraction plants using the aqueous solutions being treated by the commercial copper solvent extraction plants. Two of the pilot plant studies showed that the copper solvent extraction reagent had a significant influence on the extent of crud formation while the other pilot plant study indicated the copper solvent extraction reagent had a lesser influence on crud generation.

Jan 1, 1996

By Charles A. Hickey

The dining industry game tome Spruce Pine area a few years after tine Civil War. Two Yankees came down from Massachusetts to mine sheet mica to sell to the stove manufacturers for windows in heating stoves. At this time the method of mining was very crude; it was done only with pick and shovel. They were mining mica from the soft veins. Later they progressed to hand grilling and blasting. Hand drilling was quite an art in the area. One man would hold and turn the steel while one or two other men would drive the steel with hammers. In shaft raining, the muck and water was removed by hand winches called windlasses. About 1920 air compressors and jack hammers came into use. These were perhaps tide greatest improvement that has ever come to the area's mining industry. Later carne gasoline hoists, air drive water pumps, and all electrical equipment. Mica mining has, for the past few years, been very modern and efficient.

Jan 1, 1962

By Kailash Narayan

Atlantic Richfield Company began operating a commercial uranium solution mining project in April, 1975 in Live Oak County, 10 miles southwest of the town of George West (Figure 1). The operation is designed to produce 250,000 pounds of U303 per year and is jointly owned by Atlantic Richfield Company, Dalco and U. S. Steel. The proprietary process employed in this operation consists of injecting an alkaline leaching solution into the ore-bearing formation through a pattern of injection wells. The uranium-bearing solution is then removed through producing wells using submersible pumps in central production wells. The produced solution is pumped through a pipeline to the plant area where the uranium is extracted. The barren solution is refurbished and returned to the pattern area for reinjection. The injection field and plant site are located in the drainage of Spring Creek, a small intermittent stream tributary to the Nueces River. Land use in the area is primarily agricultural -- cattle ranching and farming -- but several producing gas fields are present in the areas as well.

Jan 1, 1976

By Alejandro Prieto

Traditionally, Mexico has been a mining country. This industry has played a very important role in our country's development, creating jobs, integrating geographical regions - generally very remote from urban communities - and, an essential factor in our present day economy, generating an influx of foreign currency. The Fluorspar mining industry's development started in the 1920?s, but it was not until World War II that its exploitation became consistent and started growing. During the last few years, Mexico has become the world's leading producer, with an annual output of more than one million tons, which directly generates over 3,000 jobs. The actual proven reserves can guarantee fifty years of production at this same annual rate, and it is due to this fact that the producers have not increased their reserves. However, there is concrete information of the existence of several deposits, extending from the northern border to the gulf of Mexico, forming the "Fluorspar Belt? in Mexico.

Jan 1, 1986

By D. G. Feuerbacher

Maximizing production of oil from sandstone petroleum reservoirs is aided by use of non-damaging drilling and workover/completion fluids. Various tests, such as X-ray diffraction, scanning electron microsccpy, petrographic microscopy, porosity and permeability are conducted on core samples. Several fluids are selected, on the basis of these results, for return permeability tests. A report is then written giving the results of all tests, potential reservoir problems, and recommended practices for exploiting the reservoir.

Jan 1, 1983

By Robert C. Freas, Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodities in this volume have as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as aggregates, fluxes, glass raw material, refractories, fillers, reactive agents in sulfur-oxide removal, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Holocene. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited availability in certain areas. Limestone and dolomite are so useful and so abundant that in 1989 about 798 Mt were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses. The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information.

Jan 1, 1994

By James W. Griffith, Sarah A. Riling

Bituminous coal dust was repeatedly placed into one lung lobe of anesthetized Macaca nemestrina monkeys using a flexible fiberoptic bronchoscope. Radiographs taken at 15 day intervals showed a focal radiographic density after 90 days time when a total of 1 gram of dust had been instilled. The radiographic density progressed slightly in size until 12 months by which time 3 grams of dust had been instilled and the animals were euthanized. At necropsy, the only significant gross lesion detected was the focal black pulmonary lesion located at the dust instillation site. Histologically, the lesion was composed of coal dust laden macrophages located primarily within interstitial tissue and interspersed with a slight amount of reticulum and connective tissue fibers. The distribution of coal dust was limited to the instillation site in the right caudal lung lobe based on radiographic, gross and histologic examination. Bronchoalveolar lavage of both right and left caudal lung lobes was performed 8 times during the 12 month long experiments without significant complications. More macrophages were found in lavage fluid from the right lung than the left, and most macrophages from right lung contained coal dust particles. Based upon a limited physical examination and complete blood count at 15 day intervals the animals remained normal during the experiment. We conclude that the primate lung's response to focal experimental bituminous coal dust resulted in a marked focal increase in pulmonary alveolar macrophages, which can be recovered regularly in high numbers by bronchoalveolar lavage. The model described has significant potential for investigating the pathogenesis of various respirable dust-induced pneumoconioses, for evaluation of new therapeutic approaches, and for refining experimental and clinical diagnostic applications of bronchoalveolar lavage. Key words: Coal Workers Pneumoconiosis, Disease model; Primate, Lung Lavage Fluids

Jan 1, 1991

By J. R. Hurley

The continuous flow, horizontal drum blender has dynamic properties which may be described by the same type of equations which often arise in electrical filter analysis. Furthermore, the equations may be readily solved by the same techniques used in electrical control analysis. For this reason the blender model developed is termed an "Electric Analog", although strictly speaking it is a mathematical model. Presentation of the dynamic performance of the blender as an electrical (or mathematical) model is desirable for several reasons. The model can be of assistance in correlating performance data with equipment design parameters. The model 'can be used with other process equipment models for simulation of an entire plant operation or in stability studies. In addition, the model may be useful in providing insight into the actual blending mechanism, or it may suggest a similar method of analysis for other closely allied equipment.

Jan 1, 1967

By Jack Barrett

The oxidants which participate in the bacterially catalyzed oxidation of minerals are dissolved oxygen and some aqueous iron(III) complexes. Speciation studies indicate that these complexes consist of iron (III) -sulfate and iron (III) -arsenate ions. The complexes have different oxidizing powers as indicated by their calculated standard reduction potentials. The thermodynamics of the oxidations of pyrite and arsenopyrite are related to the mechanisms of the reactions. The mechanisms are discussed in terms of primary processes occurring on the mineral surfaces and the secondary reactions of the primary products. The importance of the conclusions to plant operation is discussed.

Jan 1, 1993