Search Documents

The Colorado Joint Review Process (JRP), a bold step to expedite energy and mineral projects, is off and running. Blazing the trail is Amax Inc., which serve as guinea pig in JRP's development and is now test-flying the process at its Mt. Emmons molybdenum property in Gunnison County, CO. Although JRP is still in its infancy, the new permitting review process has drawn enthusiastic applause from across the resource spectrum: William K. Reilly, president of the Conservation Foundation, said JRP is "one of the most interesting projects I've seen" and called on environmentalists to monitor its progress "because it appears worthwhile." Stan Dempsey, vice president of Amax Inc., noted that of all the locales in which Amax operates, Colorado is "the only place where the complicated mine permitting scheme appears to work"-an achievement he attributes to JRP. Lynda Lee Brothers, the federal Energy Department's assistant deputy secretary of environment, reported that an extensive DOE search has not turned up "another single mechanism in all of government and private industry as good as JRP as a model for the proposed federal Energy Mobilization Board."

Jan 7, 1980

By W. B. Beerbower

Resin bolting has enjoyed wide acceptance for coal mine roof support. Beginning in 1973, the first year of significant resin bolting in coal mines, we estimate that 2.5MM resin bolts were installed. This grew to 7MM resin bolts in 1974 and 13MM in 1975. Resin bolts are currently being used in over 300 coal mines throughout the major coal producing areas of the U.S. and barring major work stoppage we expect more than 17MM will be installed in 1976. Although not a cure-all, the number of unintentional roof falls occurring in many mines has been dramatically reduced as a result of converting to this "new" method of support. 1 The improved anchorage strength of resin bolts provides better roof support. (Slide #1) This anchorage strength provides a mechanism to resist changing roof stresses along the entire length of the fully grouted resin bolt, thereby assuring stabilization of rock strata over long periods of time. The ability to resist roof displacement is borne out by readings obtained from strain gauged bolts. These findings can be summarized as follows.2

Jan 1, 1977

By Michael Beyer

Following the last Cholera Epidemic in 1872, resulting in approximately 400 deaths, the City Council of Munich decided to re¬place the former water supply system within the city limits by tapping new water supply areas outside of the city. Since 1883 Munich has been obtaining its water from the Mangfall River catchment located some 35 km to the south. Its most distinguishing characte¬ristics are as follows: 1) the water is free-flowing, i.e., a pumping system is not required as the catchment area is 100 m higher than the city; 2) the water does not normally have to be treated, meaning "spring fresh" tap water. On a daily basis, 300,000 m3 of water flow through the more than 100 year old pipes, accounting for 70% of the city's daily need. There was originally no requirement of a water tight system as strategically installed drain pipes prevented the build-up of exter¬nal water pressure on the lining. As the qua¬lity of today's water has become significant¬ly worse, the tunnels are now in dire need of restoration or replacement.

Jan 1, 1995

The challenge of the sustainable development framework in mining today is to see that the minerals sector as a whole contributes to human welfare and well-being without reducing the potential for future generations to do the same. If the minerals sector around the world is to contribute positively to sustainable development, it needs to demonstrate continuous improvement of its social, economic, and environmental contribution, with new and innovative governance systems. Canada is an international leader in mining and related technology. Metals and minerals is Canada?s second-largest earner of foreign exchange. Canadians, along with the rest of the world, are increasingly concerned about the environmental impact of mining activities. The Canadian Mineral industry has acknowledged the importance of its environmental responsibility by taking a broad range of innovative actions in order to ensure a sustainable development of its resources. This paper analyzes how the concept of sustainable development can be related to mineral enterprises. It discusses a wide range of issues under three main areas: perspectives on sustainable development; processes for furthering sustainable development; and assessment methodologies and indicators. This paper also presents a proposed framework and a core set of key sustainable development indicators that could be useful in efforts to measure progress toward sustainable development in mining. The paper concludes with a case study of some key sustainable development indicators related to the Canadian oilsands mining.

Jan 1, 2003

By Jamai Rostami

Mining, perhaps more than other industries, has been under pressure to achieve higher productivity, while reducing costs and environmental impacts. This has encouraged a move toward large-scale operations and greater integration and automation of systems. Mechanization is being used increasingly to raise production and reduce labor requirements. Yet, while transportation, ventilation and other activities have benefited from this trend, mechanization of rock excavation (for development and production) has lagged. The switch to a mechanized excavation system can be complex, requiring a thorough study of operational and cost benefits to be successful. To justify the high capital cost of mechanical mining equipment, production rates and the true costs of machine mining must be accurately estimated. To evaluate the cost effectiveness of mechanical mining for a particular operation, the total production cost (capital and operating) must first be estimated. This requires a reliable estimate of the production rate of the candidate mechanical excavator. Previously, the variable nature of rock caused performance prediction of these machines to be more an art than a science. Additionally, some of these machines are highly sensitive to operator skill. They all depend on their backup systems. The effects of interaction with the overall mining operation can be difficult to forecast. And a new system must surmount psychological barriers before it can become truly operational.

Jan 1, 1994

By C. Bemelmans

Lead alloys function effectively as oxygen evolving anodes in copper SX-EW operations and are highly resistant to corrosion. The presence of organic from solvent extraction in the electrolyte seemed to enhance solution line attack. Laboratory tests showed that lead is soluble in D2EHPA, Acorga and LIX 984 to a limited, yet measurable degree. Lead alloys and various lead phases formed on the anode were tested to evaluate their effect on the corrosion process in organic media. Possible causes for anode corrosion and mechanisms responsible for their initiation will be discussed.

Jan 1, 1996

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has developed a laboratory apparatus for continuous separation of minerals according to their dielectric properties. The unit consists of a rotating wire grid drum electrode and a fixed curved wire screen electrode positioned 3 mm apart. By applying high voltage across the electrodes, which are immersed in a dielectric fluid medium, a high-gradient electric field is produced. The high-dielectric-constant minerals are attracted and conveyed through the separator by the rotating drum electrode, whereas the low-dielectric-constant minerals settle through the fixed electrode. In typical tests, a sample of Montana chromite ore containing 43 percent chromite was concentrated to 72 percent chromite with 90 percent recovery.

Jan 1, 1977

By C. Duke

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By P. W. Hynes

Tg Soda Ash has operated a shortwall mining system in the Green River, WY trona district since August 1982. The system has proven to be highly productive. In an effort to reduce the amount of relatively expensive development mining and improve mine planning flexibility, a method to mine the return air tailgate during the shortwall retreat was tested beginning in April 1987. As of June 1988, four shortwall panels had been completed using the advancing tailgate, producing more than 739 kt (815,000 st). This paper discusses the effects of the advancing tailgate on shortwall production, development mining requirements, costs, strata mechanics, and ventilation. Shortwall mining is a hybrid extraction method combining the self-advancing hydraulic roof supports from longwall mining and continuous mining machines (Fig. 1). The technique has been only marginally successful at the majority of the nearly 20 installations worldwide. At present, the face at Tg Soda Ash Inc. is the only shortwall operating in the United States and the only noncoal shortwall in existence. Despite the method's record of limited success, the staff at Tg Soda Ash determined that the conditions in its trona mine were well suited for shortwall mining. The commitment to install a shortwall was made in late 1981 and the first panel commenced in August 1982. Between that time and June 1988, about 3.33 Mt (3.67 million st) of trona have been mined with the system from 15 panels. Annual average productivities have ranged from 818 t/shift (902 st per shift) in 1982 to 1.4 kt/t shift (1591 st per shift) in 1987. Overall, the system has produced an average of 1.3 kt/ shift (1450 st per shift). In April 1987, a method of mining the return air tailgate during shortwall retreat was tested (Fig. 2). The objective was to determine if a return airway could be established and maintained by mining a series of rooms and pillars about 7.6 m (25 ft) past the face support line. The method would allow a barrier pillar to be left between shortwall panels without requiring the mining of a separate return air tailgate.

Jan 1, 1990

By R. J. Hamilton

Considerable success has been achieved in recent years in reducing concentrations of respirable dust in UK coalmines; thankfully this has been reflected in significant improvements in pneumoconiosis statistics. However, continuous increases in mechanisation and in rates of working, accompanied by more stringent dust regulations, necessitate the introduction of improved and often more sophisticated methods of dust control. The increased application of exhaust ventilation and air cleaning techniques seems likely to be the most important step forward in dust control in coalmining during the next few years. A typical drivage in a UK mine is not more than 16 ft (5 m) wide and is supported by steel arches. In the past the majority of such roadways were driven by the conventional means of blasting and loading. Since the main purpose of ventilation was to clear blasting fumes and to provide adequate scouring of firedamp, not surprisingly it was usual to have 'forcing' ventilation. Present systems of operation are making increasing use of heading machines and it is not surprising that well over half of all drivages are now ventilated by exhausting methods. (1) The great majority of coal getting in the UK is from longwall faces, usually in seams of less than 6 ft (1.8 m) thickness. Although this method of min¬ing has many advantages in terms of safety and productivity, dust control is made more difficult because of the need for men and machines to work in the same ventilation stream. Much emphasis has been placed on improving the design and methods of opera¬tion of longwall machines to reduce dust production, and improved ventilation has provided greater dilution, and in consequence, reductions in dust concentration. On all machines water is now fed through internal galleries to the cutting elements. Unfortunately, one of the difficulties associated with mining thin seams is that there is some unavoidable cutting in the roof or floor and in many seams there are faults to be traversed and dirt bands which must be removed with the coal. Under these conditions it appears that the use of exhaust ventilation and air cleaning offers the most promising way of achieving satisfactory dust conditions.

Jan 1, 1980

In the UK as existing face capacity is replaced, many of the new faces will have higher installed powers and be located in zones of higher strata temperature. These factors coupled with the need to increase production will result in more faces experiencing environmental difficulies, especially with respect to climatic conditions. In many cases these problems are unlikely to be solved, as in the past, by simply increasing the face air quantity. Therefore other techniques including refrigeration will be necessary, possibly requiring major capital and operational expenditure. It is easy to spend large capital sums and incur high operational expenditure without achieving the desired amount of climatic control. There is therefore a great need for reliable prediction techniques to aid in the making of sound, informed decisions which will have a significant influence in the long term on the level of production costs. A computer program able to predict the heat flows and resultant climatic conditions on a long¬wall coalfaces has been developed. Throughout it's development underground measurements have been used to validate the computer model and it has been shown that for an advancing coalface under normal production conditions that the program predicts the climate to within 1°C of the measured conditions. This paper outlines a number of methods available to improve climatic conditions on longwall faces. The coalface temperature prediction program is used to quantify the effects of these methods on the climatic conditions for a model coalface and a comparison is given. In conclusion a cool¬ing strategy for longwall faces is outlined.

Jan 1, 1991

By M. Mathiba

High CO2 fluxes associated with reclaimed coal mine spoils pose an environmental hazard where such sites are used for building. CO2 concentrations in excess of 25% have been reported in homes constructed on or down gradient of such spoils. The objective of this study was to investigate the effect of a mitigation trench used at one mine site on CO2 fluxes across the trench using chamber?based trace gas measurement. LI8100 automated CO2 flux system was used to measure CO2 fluxes from 32 sample points located across a deep mitigation trench on June 8 and 9. The maximum recorded fluxes were 7.29 and 8.18 µmol/m2/s, with averages of 4.15 and 5.50 µmol/m2/s, up and down-dip respectively. These preliminary results show CO2 flux is higher up-hill than down-hill at 95% significant level. This work shows that flux measurement can be used to investigate CO2 migration on reclaimed mine land. Further work is necessary to allow geostatistical modeling of the spatial variability of CO2 fluxes over reclaimed coal mine spoils. Knowledge gained would assist mining practitioners and regulators in reclamation planning for envisaged post-mining land uses.

Jan 1, 2010

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By William R. Wayment, Wayne S. Cusitar

INTRODUCTION The process of mining removes valuable and eco¬nomically recoverable minerals from the earth. In the case of hard-rock mining, this process involves breaking and removing ore, while leaving the waste rock or host rock as intact as possible. Prior to mining, ground stresses exist in the ore and the host rock as a result of weight and tectonic forces; for the purposes of this chapter, the ore is considered to support the host rock on both the hanging and footwall sides. Two basic phenomena accompany mining. First, the hanging walls and footwalls tend to move together as the ore is removed. Second, high stress gradients de¬velop in the rock periphery of the opening; the magni¬tudes of the stress gradients vary widely, depending upon the local geometry and conditions. At various times, mining methods have used square¬set timbers, waste-rock backfill, alluvial sand fill, and tailings backfill materials, with or without cement, to replace the loss of support caused by the removal of the ore. Cut-and-fill mining has evolved to use hydraulically placed tailings for the backfill. In the stope, this fill provides massive support to the walls, thereby reducing stresses in the back. It also provides a floor from which men and machines can work to drill and blast, to haul ore, and to scale and bolt the back. In many cases, the addition of cement provides a competent free-standing wall when the fill is exposed during mining of adjacent stopes or during pillar recovery operations. In most cases, the use of fill does not eliminate standard tem¬porary or local roof control measures such as roof bolts and wire mesh. Fill Characteristics It is important that backfill used for ground support be of maximum stiffness in relation to wall closure. The stiffness of the fill is related to its placement bulk density or void ratio. In the case of cemented tailings, this is enhanced by the cement bonds. During stope closure, individual fill particles experience rotation and crushing at point contacts, but they are subject to little relative translation. The stiffness approaches infinity as the void ratio approaches zero, until the ground forces reach equilibrium, and closure stops. The gradation of particle sizes and minimal segregation resulting from good hy¬draulic placement both contribute to a high degree of early stiffness in the closure history of classified tailings backfill. This also implies that the fill should be resistant to creeping under high static loads. All mines experience shock loading situations such as blasting, and many mines experience rock bursts that can apply sudden and very high loads to the fill. Certain conditions of void ratio, particle size, and moisture con¬tent can result in mass fluidization of unconsolidated fill during such shock loading. Two key factors in avoid¬ing fluid behavior are the provision of a well-drained fill through desliming or classification and the achievement of a small degree of consolidation through the addition of cement in ratios as lean as 40 to 1 (2.4% cement). The acceptance of classified mill tailings as backfill material has been enhanced by its relative economy, including its source, preparation, delivery, and stope distribution. Transportation from the backfill prepara¬tion plant on the surface into the stope usually can be accomplished with low power consumption, with low labor costs, with few capital costs, and at high tonnage rates. An additional benefit is a reduction of the storage volume required for surface disposal of the tailings stream, with a resultant improvement in the environ¬ment. The costs of placing cemented tailings backfill generally range from $1.65 to $6.61/t ($1.50 to $6.00 per st) of fill depending upon the cement ratio used. Scope This chapter examines a major backfill program at a mine and mill complex where the backfill facilities are included as a part of the original planning. The backfill preparation plant is intended to make maximum use of remote controls and automation. The logistics asso¬ciated with material storage, handling, and metering in the plant are outlined. Important considerations in specifying equipment for typical service conditions are discussed. The fill delivery system is described, includ¬ing the boreholes, level lines, and stope distribution lines. Stope preparations for fill confinement and drain¬age are described, as are the techniques of placement and distribution. Methods of controlling and directing the flow of drainage water and slimes are presented, along with the facilities and equipment for clarification, pumping, and sludge removal. As shown in Fig. 1, the fill program encompasses most aspects of the mining and refining facilities, so the discussion is brief in each area. The preparation of backfill of a uniform and con¬trollable quality is presented here as a material handling problem. The balance of the presentation concentrates on the logic of the system, the costs where meaningful (in 1977 US $ unless otherwise specified), and some operating "tricks" that have contributed to system per¬formance and reliability. SURFACE PREPARATION PLANT A backfill preparation plant is required on the surface. This plant generates suitable fill material from the stream of mill tailings. Among the functions of the plant are: 1) Slimes are removed to improve the percolation characteristics of the fill; typically, particles finer than 325 mesh are removed from the tailings. 2) Tailings and sand storages are provided so that the steady stream of tailings produced by the mill can be accepted. Provision is made to accommodate the cyclic high-volume demand from the mine. 3) The plant stores the cement and contains meter¬ing and mixing facilities to provide fill of a controllable and uniform quality. 4) The hydraulic backfill delivery system is a part

Jan 1, 1982

By L. G. Austin

A program has been written to combine the Klimpel-Austin approximate model for liberation in a binary system with a mill model applicable to ball milling. The model applies for a system where the volume fraction of valuable B in host matrix A is small. The mill model is treated as an equivalent series of fully-mixed reactors. Twenty-three classes of material are considered: pure A; pure B; unchanged AB; 0-10.2 B in AB either as surfac- exposed B or as wholly-contained grains of B; 10-20% B in AB, surface-exposed or wholly- contained;etc.. to 90-100% /b ub /ABm syrface-exposed or wholly-contained. Illustrative cases are given making reasonable assumptions concerning relative rates of breakage and primary breakage distribution functions for each class of material.

Jan 1, 1986

By Yoginder P. Chugh

The term "fatigue" in mechanics, is used to refer to reduction in the strength of a material subjected to fluctuating or alternating stresses. Stresses that vary with time are called fluctuating stresses and if during fluctuation the stresses also change sign, they are called alternating stresses. In the field of rock mechanics, the term fatigue (static fatigue) has often been misused to refer to failure of geologic materials in time domain under constant load. To avoid confusion, we use the ten cyclic fatigue here to refer to failure of rock under alternating or fluctuating stresses. Fatigue in metals has been studied for over 100 years. Fatigue properties of geologic materials have, however, received little attention in the past. This is probably because until recently very little was known in regard to the behavior of geologic materials even under static loading. Secondly, suitable equipment for conducting cyclic fatigue experiments was not available until quite recently. A few cyclic fatigue studies have been undertaken on geologic materials to relate it to percussive or rotary drilling mechanisms (e. g. Grover et a11*; Burdine2). The results of these studies were inconclusive due to limited effort. Cyclic fatigue in concrete has been studied more extensively than geologic materials (e.g. Nordby3, Gray et al 4 and Bennett et a15) and mechanisms of fatigue in concrete are better understood than in geologic materials.

Jan 1, 1975

By D. R. Kalasky, J. M. Mutmansky, B. Kolonja

This paper considers simulation of truck dispatching systems using maximum expected production of the truck-shovel system as the measure of performance. Two analysis methods are utilized: multiple comparisons with the best (MCB) and the combination of MCB with the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. Results show that the combined procedure of MCB with CRN is the superior tool to use to reduce the total number of replications needed to ensure the specified probability of correct selection from a number of systems. In this case study, MCB with CRN reduced the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1995

By J. Gathje

Normal process development for pressure preoxidation treatment of refractory gold ores starts with laboratory batch autoclave tests, followed by operation of a continuous autoclave pilot plant for confirmation of the various process options. This scheme will generally provide good information showing the effects of such variables as grind size, time, and temperature, and will indicate whether autoclave preoxidation will produce solids that are amenable to cyanidation for gold recovery. However, several recent test programs conducted over the last three to four years have shown that the cyanide leaching responses of treated solids from the batch tests can differ considerably from those achieved by the continuous pilot plant autoclave. Examples are provided to demonstrate these differences and to show the importance of extending the laboratory investigations to include the use of a semicontinuous autoclave test procedure. A test case is cited in which this procedure provided data that could not be obtained from batch tests.

Jan 1, 1995

By Wade N. Ellett, K. Marc Le Vier, Timothy A. Fitzpatrick, Kenneth A. Brunk

As the gold mining industry matured through the 1980' s, and into the 1990's, the development of refractory gold orebodies has become more prevalent. Newmont Mining Corporation developed and commercialized flash chlorination for the treatment of carbonaceous preg robbing ores; Homestake Mining Company developed and commercialized the industry's first application of autoclaves. Barrick installed the world's largest autoclaves on whole ore treatment a few years later. Dry grinding and roasting followed at Placer Dome's Cortez, Freeport -Independence and Newmont's Carlin operations. Today, numerous papers are presented on research efforts worldwide which address treatment of refractory gold ores by bioxidation, roasting, autoclaving, alternative lixiviant treat­ment and other novel process ideas. The overall objectives are to develop economic processes for difficult refractory ores where no process exists or conventional practice is cost prohibitive. Successful research can lead to lower operating costs, increased profits, and increased ore reserves. One such research effort directed by E I DuPont de Nemours and Company, Advanced Mining Technologies, was focused on gold ores which were refractory in nature due to the cyanide soluble copper content. Approximately five years of research effort culminated in a patented process (U.S. Patent 5,411,575)1 and the formation of a new joint venture company, AuGMENT Technologies, in 1995 with Newmont Mining Corporation. Today significant progress has been made in moving the laboratory scale tests to commercialization.

Jan 1, 1997

By Richard C. Sale

INTRODUCTION The topic of the paper is to discuss the use of micro computers in the construction industry. I will first discuss the present situation of the PCs in our industry followed by a discussion how Guy. F. Atkinson has integrated the PCs into it's organization. I will close with some general comments that any organization should review in order to enhance the use of their PCs both at the job sites and home office locations. PRESENT SITUATION OF THE PCs IN OUR INDUSTRY Today, the possible number of combinations that can be obtained when bringing together the available models of PCs, with their peripherals and software, is astronomical. With this array of equipment that can be bought, plus the new and possibly better equipment that is being put on the market almost daily, it is indeed a very difficult task for an organization to know how to invest its money in computer equipment. At the job sites, the work is fast paced with little time available to fully learn what the PCs can do to help with the required paperwork. I am still waiting for the day when someone has to tell the superintendent at the job site that he cannot start pouring concrete or shoot the next round because no one can get the computer to work.

Jan 1, 1987