Search Documents

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

By H. Yilmaz

A testing method for assessing the shear-bond strength of thin spray-on liner (TSL) on rock substrate was developed at Wits University Rock Mechanics Laboratories. The gap between a 20 mm thick steel ring and a rock core is filled with TSL along the depth of the ring. After the curing of the TSL for a predetermined period, the sample is placed on a base, which offers support to the steel ring and the TSL but not to the rock core. A compressive load is applied on the rock core displacing the core on TSL contact and punching it towards the void in the support base. Shear-bond strengths for different TSL products as well as shotcrete were measured. This paper describes the test set-up and points out the important aspects and procedures during sample preparation and test execution. The test results are also presented and discussed.

Jan 1, 2007

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

By Y. Z. Ma

This paper presents a matrix formulation of factorial kriging, and its relationships with simple and ordinary kriging. Similar to other kriging methods, factorial kriging can be applied to both stationary and intrinsic stochastic processes, and is often used as a local operator. Therefore, the concepts of intrinsic random function and local stationarity are first briefly reviewed. Kriging is presented in a block matrix form in which the kriging solution is useful not only for understanding the relationships between simple and ordinary kriging methods, but also the relationships between interpolative kriging and factorial kriging. When used as a signal/noise-filtering method, factorial kriging is especially useful for multiscale modelling. Examples for general signal analysis and geophysical data signal filtering are given to illustrate the method..

Jan 1, 2014

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

By C. G. Anderson

"As demand for copper and precious metals continues to grow, the need to develop new supplies increases. In the imminent future, the new large global ore bodies are more complex, with enargite, tennantite and tetrahedrite as the abundant contained mineralogy. These resources also contain considerable gold and silver. As such, direct treatment by conventional smelting is prohibitive due to the potential environmental impacts and copper quality issues. This paper outlines the effective application and associated economics of industrially proven Alkaline Sulfide Leaching (ASL) hydrometallurgical technology to an enargite concentrate for selective removal and recovery of arsenic, antimony, gold and silver, leaving a clean high-grade copper concentrate. The fundamentals behind the technology are described, along with those of hydrometallurgical arsenic fixation and stabilization. Flowsheets and unit operations are elucidated, along with an in-depth economic analysis. INTRODUCTION Hydrometallurgical methods can be employed for treatment of gold-, arsenic-, antimony-, tin- and mercury-containing materials, concentrates and ores, as well as complex ones containing any number of metals (Conner & Anderson, 2013). The alkaline sulfide leaching (ASL) system is one of these. It is essentially a mixture of sodium sulfide and sodium hydroxide with other meta-stable alkaline species as required. This is a unique hydrometallurgical system beause it is a very selective lixiviant for the distinct leaching of tin, gold, antimony, arsenic, tellurium, silver and mercury (Anderson, 2000, 2001a, 2001b, 2002, 2003, 2012, 2014; Anderson & Twidwell, 2008a, 2008b, 2010; Anderson et al., 2004, 2005; Glazkov & Tseft, 1961; Gnatyshenko & Polyvyanni, 1961; Nadkarni et al., 1975; Nadkarni & Kusik, 1988; Polyvyanni, 1963). Worldwide, ASL technology has been employed industrially in the former CIS, China and the United States for the production of antimony (Anderson et al., 1992, 1994; Anderson & Krys, 1993; Holmes, 1944; Kaloc, 1967; Nordwick & Anderson, 1993; van Stein, 1971)."

Jan 1, 2015

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

By J. Danoczi

Specially designed X-ray machines are used extensively on diamond mines for the recovery of diamonds from ores. These machines are extremely expensive and, at present, there are no reliable methods of determining if the equipment is performing efficiently. The objective of this work was to manufacture translucent X-ray diamond simulants, which would emit varying but known luminescence signals when exposed to X-rays. These X-ray diamond simulants could then be used to determine the efficiency of diamond recovery operations.

Jan 1, 2008

By O. Rondon

Localized uniform conditioning is a technique developed to spatially locate selective mining unit grades that have been derived using uniform conditioning for the assessment of recoverable resources. The technique has the advantage of producing selective mining unit estimates conforming to the uniform conditioning panel-specific grade-tonnage curve while introducing spatial information at the scale of the selective mining units. This paper describes an alternative technique to localized uniform conditioning which does not explicitly require the uniform conditioning panel-specific grade-tonnage curve to localize the selective mining unit estimates. The technique can therefore be implemented in mining software where uniform conditioning is not available.

Jan 1, 2014

By M. D. G. Salamon

It has been noted in recent years that the pillars in some bord-and-pillar workings scale or spall. In due course this process may result in the collapse of the affected panels. This paper presents a methodology for assessing the long-term behaviour of such workings, employing a simple model of pillar deterioration by scaling. It is assumed that scaling causes a gradual reduction in pillar width, hence the safety factor of pillars reduces in time. It is also postulated that the process of scaling will be arrested if the coal rubble around the pillar reaches a critical height. The probability that the pillars will survive for a certain period of time, or indefinitely, can be estimated. This can be accomplished by using the log-normal distribution proposed by Salamon and Munro4todescribe the distribution of the apparent safety factor values at failure. If an estimate of the rate of scaling is known, it is also possible to quantify, using a Monte Carlo technique, the expected life of the pillars. The method also facilitates pillar design by specifying a probability of survival for a given number of years or, alternatively, for an indefinite period. Using the limited pool of available data, analyses show that the proposed model does not appear to be inconsistent with observed behaviour of pillars in the Vaal Basin. The crucial parameter is the rate of scaling. Back calculations from eleven cases suggest that the rate of spalling in the Vaal Basin is about 0.2 m/year. It is noteworthy that two further cases in the same area give significantly higher rates (0.85 m/year). Some underground observations in the Witbank area indicate considerably lower rates in the order of 0.02?0.04 m/year. Further areas for study are recommended. These include a study of old workings to determine the extent and rate of scaling in the various coal fields, an investigation into the possible relationship between scaling and the chemical composition of the coal. In addition, model studies will be required to assess the practical impact of the research findings.

Jan 1, 1998

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By B. Solar Menéndez, M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza

The analysis of subsidence due to the opening of an underground void (mining, water exploitation or civil works hole) is a problem usually hard to solve. First of all, it requires a predictive model, in order to define both the displacement magnitude and area affected by subsidence. Such model should be validated with measurements of the actual movements sustained on the surface, in order to adjust it properly and enable influence of future behaviour in a reliable way. Two different kinds of problems might arise. On one side, it is necessary to control and measure surface movements in a very exhaustive way during a long period of time, beginning before underground works take place and finishing years after they are over. Furthermore, three factors bring in errors, some times of magnitudes higher than the displacement magnitudes measured. These include: the fact that reliable and long-term information cannot always be achieved; the precision of measuring devices; and the design of the topographical network itself. In addition, the predictive models more widely used only apply to certain excavation geometries, mainly to horizontal holes. In light of this background, the Group of Rock Engineering, of the University of Oviedo Mining Department, has developed a working methodology and a specific software tool, Subsidence 3D, to estimate ground displacements and strains. The program will allow for predictive models to be defined and also allows the treatment of data related with topographical marks and its comparative analysis with calculated results. The software has been programmed using Visual C++. Graphical outputs however are generated using AutoCAD 2000. This paper mainly refers to a practical situation, an underground coalmine, remarking the main difficulties arisen during the study of the available information and proposing how to solve them. A predictive model in subsidence 3D was established and validated. The actual behaviour of the ground was that in the model.

Jan 1, 2003

By D. Boshoff

The ability of an explosive to break rock is influenced considerably by the extent of confinement in the blasthole. It is believed that confinement is improved by the use of adequate stemming. The aim of this paper is to present the results of the first and second stages of developing a stemming performance testing rig for small diameter boreholes. The rig was used to compare and contrast the performance of different designs of products. The results showed that different stemming products have differences in terms of their functionality, which can have a major impact on the efficiency of rock breaking. Two test procedures were used, one through the exclusive use of compressed air and the second using a purpose-built high pressure test rig with small quantities of explosives. Both tests were used to identify and evaluate the ability of various stemming products to resist the escape of explosive gas through the collar of a blasthole. An investigation was done to determine the types of stemming products most commonly used in South African underground hard rock mines, and these products were used during the tests. The first stage of tests using compressed air only did not prove adequate to predict with certainty the pressure behaviour in the borehole of a particular product under high pressure conditions. The purpose-built high pressure test rig also did not prove to be a very effective tool to test stemming products under high pressure conditions. The test rig incorporated only the effect of gas pressure on the stemming product, and excluded the effect of the shock wave. This study therefore proved that to take into account only the gas pressure generated in the blasthole is not sufficient to effectively test stemming product performance.

Jan 1, 2011

By A. Amiel

Tarkwa Gold Mine is owned by Gold Fields Ghana, IAMGOLD and the Government of the Republic of Ghana in a 71%, 19% and 10% ratio. The mine is operated by Gold Fields Ghana. This large, low-grade, open pit, gold mining operation is located in Tarkwa, in the Western Region of Ghana, approximately 320 kilometres by road, west of Accra, the capital of Ghana, West Africa. In the Financial year ended June 2007, the operation mined a total of 108 million tons of which 22 million tons was ore. The mined ore is processed through three gyratory crushers supplying two heap leach pads (north and south) and a carbon-in-leach (CIL) plant. Before the 6 Sigma project commenced, the current fragmentation was resulting in sub-optimal feed size to these crushers. It was decided to use 6 Sigma methodology to improve the fragmentation. A defect was defined as a fragmentation analysis indicating less than 95% passing 750 mm. The objective was to improve fragmentation in order to achieve a constant throughput to the north heap leach crusher of 1500 t/h, a 5% increase in pit loading efficiency and a 50% decrease in rock breaker hours, equipment damage costs and in-pit sheeting costs respectively. However, this was not to be achieved at the expense of grade control as Tarkwa is exploiting a low grade, high volume deposit and therefore ore dilution must be kept to a minimum. This paper is intended to take the reader through the various 6 Sigma phases of the project (define?measure?analyse ?improve?control), which have resulted in a 10% reduction in loading times, of which half has been attributed to improved fragmentation, as well as a substantial increase in blasted stocks. The focus has been on both drilling and blasting parameters as both processes had to be taken into account. These parameters are technical but personnel factors were also identified and dealt with as they arose. In order to measure the impact of any change in the process parameters on the fragmentation size distribution, cameras have been acquired. One has been installed looking into the bowl of the north crusher and the other one was dedicated to field observation, of individual blasts. Both are used for ongoing fragmentation analysis. At Tarkwa, mining efficiency is strongly dependent on good fragmentation as well as the presence of unblasted ?toes? on the pit floors. Crusher throughput depends on an acceptable ore fragment size. Compliance with plan for actual hole depths was temporarily monitored by manual hole dipping, but this is now being replaced with a fully automated drill data management system developed by Sandvik and Modular Mining. The Six Sigma methodologies, using control charts based on data collected in the field, allowed the mine to improve methods for the control of blasted material. It also enforced the implementation of a quality control programme encompassing the entire drill and blast process.

Jan 1, 2008

By S. M. Spottiswoode, J. A. L. Napier, M. Kataka

The move away from the use of strike stabilising pillars at depth and the adoption of the more flexible system of mining towards final dip remnant pillars brings new opportunities for optimising mine design. In the initial planning stage, the size and spacing of the final pillars is designed using classical design criteria, through limiting modelled values of Energy Release Rate (ERR), Average Pillar Stress (APS) and Excess Shear Stress (ESS). In reality, mines often leave pillars that are larger than those originally designed. One of the reasons for leaving more ground is an unexpectedly high rate of seismicity. In this paper, we present developments in integration of modelling and seismicity that are aimed at developing design criteria that are more responsive to local conditions.

Jan 1, 2003

By Y. M. Chen, H. L. Zhang, W. U. Bing, C. Q. Zhou

Multiphase flow in the widely used Vanyukov furnace was numerically studied. An unsteady three-dimensional and three-phase flow model was firstly built using the computational fluid dynamics (CFD) software ANSYS FLUENT®, and then solved with the volume of fluid (VOF) and k - ??model. The results showed that the proposed model could be used to predict the multiphase movement, the slag/air fluctuation, the vortex formation, and effects of structural and operational parameters. By fast Fourier transform (FFT), the dominant frequency of density with time signal was calculated as 0.29 Hz. The analysis of different injection flow rates of enriched air indicated that this variable has a major effect on the mean slag velocity. The peak mean velocity increased from 2.17 to 4.99 m/s while the flow rate of enriched air varied from 70 to 160 m/s. The proposed model provides a method to optimize the furnace structure and operating conditions for the best furnace performance and lowest energy consumption.

Jan 1, 2015

By F. P. Hassani

Today, mine backfilling has become an integral part of mining operations, both from a local and overall ground control point of view, and as regards mining techniques and environmental considerations. During the past decade, substantial research has been carried out to contribute to the better understanding of the mechanisms involved in mine backfill behaviour. This work involved analytical, experimental and numerical studies at different scales. Accordingly, this work has been aimed at developing backfill design guidelines for actual working conditions. Backfill design for deep mining conditions is complex and requires understanding of various elements. The most important of these elements are: backfill inherent strength parameters, backfill placement method, stope geometry and interaction between backfill and host rock. The mobilization of backfill strength parameters controls the backfill behaviour and thus, its failure mode. It is believed that the governing boundary conditions and backfill-rock interaction influence the backfill strength mobilization significantly. Accordingly, the interaction between backfill and host rock is an influential factor in overall backfill behaviour under applied loads. The focus of this research is to investigate the backfill-rock interaction, considering a nonlinear behaviour for both backfill and rock mass. Assuming typical stope geometry, the FLAC code was used to model the complex boundary condition associated with narrow vein mining conditions and to simulate the backfill behaviour. A comprehensive numerical study was conducted and the results obtained were compared against field observations. The analysis of findings provides qualitative results, which can be used for backfill design. Keywords: Numerical modelling, backfill, deep mining, non-linear behaviour, rock mechanics, backfill behaviour, narrow vein mining.

Jan 1, 2008

By F. M. G. Egerton

Mechanisation of mining operations is not a new concept in the world of mining. Machinery has been developed, manufactured and used for many decades in massive orebodies and coal mines, both locally and abroad. Because of their size and the huge tonnages available, massive ore bodies lend themselves very easily to mechanisation. However, little progress in mechanisation has been made in narrow tabular orebodies in South Africa. The equipment available for narrow tabular orebodies requires excavations of a size that introduce large volumes of waste dilution. Nevertheless, it is essential for South African miners to experiment with mechanisation and to find a solution to the problem. This address looks at current conventional mining methods and compares them to bord-and-pillar type mining methods. Off-reef mechanisation is also touched on. It then looks at different hybridised mining methods that are being used, i.e. a mixture of conventional mining and mechanisation. It finally looks at future prospects for mechanisation in narrow tabular orebodies.

Jan 1, 2004

By C J. de Beer

The Kwaggashoek East pit is one of the four production areas of Thabazimbi Iron Ore Mine. The Kwaggashoek East Open pit mines through the abandoned sublevel caving operations of the Kwaggashoek East underground workings. A risk assessment indicated that the primary risk is the occurrence of surface subsidence. Based on local knowledge, a hypothesis, that most of the cavities were filled with broken rock as a result of roof collapse and bulking of failed material was formulated. To test the hypothesis a number of geophysical methods as well as probe drilling was utilized. The results of the resistivity, gravity and ground penetrating radar surveys were inconclusive in determining the position of voids. Either there were no voids present or the resolution of the surveys was not high enough to pick it up. It is accepted that only small voids remained, and that the supported roof hypothesis is valid. As a precautionary measure all the production blast holes within the caving area were over-drilled by forty percent. This would collapse the roof of any small voids or tunnels immediately below the block. This operation proved to be successful as two of the three underground levels have been mined out with no subsidence occurring in the pit floor.

Jan 1, 2006

By C. Musingwini

The subject of optimal planning of level and raise spacing for inclined narrow reef deposits has received intermittent attention over the years because the subject matter is inherently complex. Previous work has approached the problem as simply that of simultaneously minimizing the total excavation and haulage cost associated with the development workings. However, when level and raise spacing are altered, other factors such as productivity are negatively affected, thus requiring a delicate trade-off of contradicting planning or optimization criteria. The paper concludes that the problem is actually of the multi-criteria decision analysis (MCDA) type, contrary to traditional thinking that the planning problem is achieved solely by minimizing waste development.

Jan 1, 2010