Search Documents

Proceedings of a General Meeting held at the Witbank Golf Club at 19h30 on 3rd November, 1977 Geomechanics colloquy The 27th Geomechanics Colloquy is to be held on 12th and 13th October, 1978, in the Salzburg Congress Hall. The themes of the four half-day sessions will be as follows: Conference on pneumoconiosis The Vth International Conference on Pneumoconiosis is to be held in Caracas (Venezuela) from 29th October to 3rd November, 1978.

Jan 1, 1978

Currently the most widely used formula in pillar design is the power formula, which implicitly assumes a volume effect. This assumption is critically examined, and it is proposed .that a limiting strength value, the critical rock mass strength, be used for pillar design instead. A methodology is provided to determine this value. It is suggested that the effects of geometry on pillar strength are well described by a linear function and the power formula, for w/h ratios less than or equal to about 5. This approach together with the use of the critical rock mass strength, removes the volume effect. Various factors that affect pillar strength are examined. The concept of explicitly determining the stability of each component in the pillar system is briefly discussed. It is proposed that pillar design be expanded to a pillar system design procedure that incorporates the interaction of the pillar, roof and floor strata, and the loading system.

Jan 1, 1998

By H. M. Wells

The influence of economics on the design of mine shaft systems by H, M. WEI.LS, Pr. Eng., M.Se. (Fellow) The purpose of this paper is to review some of the more important economic criteria that must be taken into account when planning the number, type, size, and distribution of the shafts, or shaft systems, required to exploit a block of payable ore. The postulated philosophy governing the selection of design parameters is that of optimization of the financial return per rand of venture capital employed for the project as a whole. While this criterion may not necessarily satisfy the investment objective under all circumstances (as, for instance, where risk limitation is important), it does serve to place the relative economic advantages and disadvantages of specific design features, which may sometimes be in opposition, into correct perspective with respect to the overall economics of the project under the prevailing economic climate at the time of the investigation.

By J van Rooyen, S. Archer, M. Fox

The use of dilute sulphur dioxide (SO2) gas mixtures for the oxidation/precipitation of manganese has been explored widely in recent years. The technical merit of the concept is well proven and implementation of the technology on commercial scale is imminent. This paper reviews the technology of manganese removal by means of dilute SO2 gas mixtures and highlights some of the challenges associated with its implementation on industrial scale. A brief review of the technology is presented; the review considers both the mechanism and chemistry of manganese oxidation/precipitation with dilute SO2 gas mixtures. The impact of variables such as temperature, pH and SO2 concentrations on the manganese removal process is assessed. Challenges associated with implementation of the technology on industrial scale are discussed. Gas dispersion is highlighted as a critical design consideration.

Jan 1, 2007

Infacon 74 The National Institute for Metallurgy, the South African Institute of Mining and Metallurgy, and the Ferro-Alloy Producers' Association of South Africa extend a cordial invitation to participate in the International Ferro-alloys Congress to be held in Johannesburg, South Africa, in April 1974. Obituary RICHARD AUSTIN COOPER On the 31st March 1972, a once very active member of the Institute, R. A. Cooper, died at the age of 82. He had served on the Council for many years and was Vice-President in 1933/34. ALEXANDER JEREMIAH ORENSTEIN CB., CM.G., C.B.E., LLD., D.Se., M.D., M.R.C.S., F.R.CP., F.R.S.H. Dr Orenstein, who died on the 7th July 1972 at the age of 92, was so well known and so widely acclaimed during his lifetime that it is difficult to add to the tributes which have already been paid to him.

By Siemag Transplan GmbH

At the Hansa Mine in Dortmund, Germany, coarse run-of-mine coal, up to 60 mm in particle size, has been brought to the surface hydraulically from a depth of 850 m since November 1977. Hoisting is done by a three-chamber pipefeeder, by means of which up to 400 t/h can be lifted. The pipefeeder operates without problems, and has so far shown itself to be efficient and reliable. Vertical hoisting can be carried out by water supplied from the surface, from underground, or from a surface water supply in combination with minewater from underground. Water that flows into the mine, which would in any event have to be pumped to the surface, can be utilized for hoisting operations. The energy costs per ton of coal for a lifting height of 850 m vary between 41 and 62 South African cents, and therefore lie within the range of costs that apply to conventional hoisting.

Jan 1, 1980

By Jean Michel Marino, Jean-Pierre Slama

"The computer methods used by the French Commissariat a l'Energie Atomique, which are applicable to any type of ore deposits, are:(i) Ore reserve estimation. The data are either the core analyses or gamma leggings. To determine the spatial distribution of the ore, three different methods of interpolation are used. Two of these are based on the least-squares theory and the third one is an application of the regionalized variable theory. The interpretations of the orebody by the geologists are introduced in the computer program as often as possible.(ii) Optimal open pit design. From the spatial distribution of ore, the three-dimensional outlines of the optimal pit are determined by a geometrical algorithm which allows different slopes varying with the azimuth.Finally, the optimization of annual successive plans arc discussed."

Jan 1, 2014

By S. L. Crouch

This paper describes a numerical procedure for the computation of the displacements and stresses induced by the mining of a tabular ore deposit in faulted ground. The numerical procedure is based on the displacement discontinuity method, which can be regarded as an application of Salamon's 'face element principle' to cases in which the reef plane is faulted into several sections, or even folded in an arbitrary way. An element of a fault is modelled in the same manner as an element of the reef, except that a fault element is allowed to undergo permanent inelastic deformation (i.e., slip) if the stresses transmitted through the fault-filling material satisfy a Mohr-Coulomb yield condition. An iterative technique for the incorporation of a Mohr-Coulomb yield condition in the general displacement discontinuity method is explained. This technique is illustrated by means of a simple example involving the mining of a flat-lying reef intersected by a fault. The displacements and stresses at selected locations along the fault are examined as the reef is mined, element by element. A consideration of the energy changes reveals that the occurrence of slip along a fault leads to a sudden increase in the energy release rate due to mining as the excavation intersects the fault. The energy release rate then falls off abruptly to a value less than that which would occur in the absence of any slip, and gradually builds up to re-establish the conditions that would exist in unfaulted ground.

Jan 1, 1979

By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf

The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.

Jan 1, 1978

By Ralph H. Nafziger

This paper reviews the major deposits of lower-grade chromite in the world, and a wide variety of methods used for the recovery of chromium from them. Gangue materials in more coarsely sized ores can be separated by gravity means, whereas flotation techniques are required for finer-grained materials. However, unless there is considerable Iron In the ores, physical means cannot increase the Cr/Fe ratios. Chemical techniques such as hydrometallurgical methods, chlorination, roasting and leaching, and smelting are required for this purpose. A greater understanding of the physical properties of chromites and the chemical reactions that take place in the recovery operations is required before. the recoveries from lower-grade chromites can be maximized. More efficient recovery operations can be realized If It can be shown definitively that the reduction of chromites occurs via either a gas-solld or solid-solid mechanism, for example. The effects of specific impurities on the chromite reduction reactions need to be better understood, as do reagent and pH control in the flotation of chromite.

Jan 1, 1982

By H. P. Carlisle

The significance of the mineralogical and surface characteristics of gold grains in the recovery process by C. E. FEATHER and G. M. KOEN Published in the Journal. February 1973. DISCUSSION H. P. Carlisle. B.Sc. (Eng.) Rand (Fellow) The authors are to be congratulated on drawing attention to the importance of surface characteristics in the treatment of gold grains. I must, however, confess to considerable doubts about the validity of the distribution of gold in "free" and "locked" form set out in Tables I to IV.

Discussion of the previous paper E. N. H. MOLLOY The first 22-foot-diameter Aerofall mill was installed at Mangula in 1957. This was fitted with cast-iron trunnion'! located to the mill shell with 2-inch-diameter mild-steel bolts. O.F .S. Branch Minutes of the General Meeting held at the Welkom Club on Wednesday, 2nd June, 1976, at 4.00 p.m. Mr G. J. C. Young (Chairman of the O.F.S. Branch) was in the Chair. Also present were:

Jan 9, 1976

By Y. -H. Chang, Y. -J. Jou, T. -S. Ueng, I. -H. Peng

In order to systematically study the size effect on the shear strength of rock joints, this study used the computer-aided-manufacturing system to reproduce the artificial rock joints for saw-toothed joints, Barton's standard joint profiles of JRC = 4~6 and 18~20, and natural rock joint profiles. We divided, enlarged, reduced, and assembled these joint profiles to obtain joint specimens of various sizes ranging from 75 mm to 300 mm in length. The shear strengths of these joint specimens were tested under different normal stresses using a direct shear test apparatus. The surface conditions of the joints at failure were also examined. The size and geometry effects on the shear strengths of these joints of various sizes and configurations were evaluated based on the test results. Um die künstlichen Trennflächen für reguläre dreieckige Trennflächen, Bartonsche standardmäßige Querschnitte der Trennflächen von JRC = 4~6 und 18~20 und natürliche Querschnitte von Trennflächen wiederherzustellen, benutzt diese Forschungsarbeit das Computergestützte-Erstellungssystem, damit die Maßstabswirkung auf die Scherfestigkeit von Trennflächen systematisch untersucht werden kann. Die Querschnitte werden geteilt, vergrößert, verkleinert und zusammengesetzt, um Trennflächenproben in Längen variierend von 75 mm bis 300 mm zu erhalten. Die Scherfestigkeit dieser Trennflächenproben wird unter unterschiedlichen Normalspannungen mit einem Direktscherversuchsgerät getestet. Die Querschnittszustände der Trennflächen bei Versagen werden ebenfalls untersucht. Nach den Untersuchungsergebnissen werden die Maßstabs- und Geometriewirkung auf die Scherfestigkeit dieser Trennflächen verschiedener Größen und Konfigurationen ausgewertet. Pour étudier systématiquement l’effet de la dimension des fractures des roches sur leur résistance au cisaillement un système de creation de fractures artificielles à l’ordinateur a été employé. Des fractures artificielles triangulaires, profils de fractures de Barton avec JRC = 4~6 et 18~20, et profils de fractures naturelles ont été reproduits. Les profils des fractures ont été arrangés de manière à obtenir des échantillons de longueur entre 75 et 300 mm. Une boîte de cisaillement a été utilisée pour étudier la résistance des fractures au cisaillement, sous plusieurs conditions de contraintes normales. Les conditions superficielles des fractures après rupture ont été étudiées. Les résultats de ces essais, effectués sur plusieurs échantillons de dimensions et configurations variées, ont contribué à établir l’influence des dimensions et de la géométrie des fractures sur leur résistance au cisaillement.

Jan 1, 2003

By G. J. C. Young

The new metallurgical plant has a simple, compact layout, being designed for a small team of operators. The reasons for building the new plant are given, and its various sections are briefly described. These include the conveyor plant, milling plant (for run-of-mine milling), thickener plant, agitator plant, filtration, clarification, smelthouse, and central core joining the mill and filtration sections.

Jan 1, 1978

By L. Dison, J. A. Hahn, G. E. Blight

A system of artificial support for shallow mines is described, analysed, and evaluated. The system can be designed rationally to support a predetermined overburden load, and tests have shown that the design theory gives accurate predictions of strength. The support system, consisting as it does of two basic materials, reinforced granular material and reinforced cemented material, is flexible and can be varied to suit changing requirements of height and load. The system of preloading to the design load by jacking off the roof ensures that the walls are both stiff and prooftested.

Jan 1, 1982

Advanced process and equipment analytics have been around for a while. However, with accessible IT infrastructure and site maturity, it is possible to analyse, monitor, and control processing plants and equipment easily. These various disparate systems provide different reports requiring the involvement of various personnel and attention to different reporting platforms. For efficient harnessing of the systems? capabilities, as well as effective improvement and monitoring of process and equipment, a single point of entry is required. A process and equipment optimization solution was required at a concentrator in South Africa, focussing on the product stream of platinum group metal (PGM) concentrate from the UG2 Reef. The investigation of data to identify strategies for optimization was required to allow visibility into plant operations to guide operators, an easier method to identify process loop problems, identification of imminent equipment failures, and advanced process control to optimize throughput and stability. A collaborative effort between the client and General Electric Intelligent Platforms (GEIP) investigated data-driven solutions to each of the problems. With the focus on process optimization and asset monitoring, as well as equipment monitoring, a combination of approaches was utilized to address the various problem areas that were identified. Each was implemented separately in the control layer of the plant IT infrastructure. The integration was done in a centralized web-based reporting tool that integrated the detailed results from the various solutions. On the process control side, monitoring of control loops was included by calculating performance statistics that were reported daily to identify sub-optimally performing control loops and indicating potential problems. The advanced process control solution for this site includes a surge tank controller, stabilizing flow through the flotation banks, and preventing the surge tank from overflowing or running empty. Equipment monitoring was investigated, for preventative maintenance, by making use of statistical data models to indicate imminent equipment failure. These predicted alarm events included the cause for failure, drilling down, and allowing focus on a specific variable for preventative action. The results included a more stable flow through the mill, with fewer stoppages due to surge tank overflows or running empty. The causes for process drift could be identified and operators could react early. Alarms warning of equipment failure 2½ and 4 months in advance were identified in an offline analysis.

Jan 1, 2012

By H. M. Wells

The investment decision under uncertainty by H. M. WELLS, Pr. Eng., M.Se. (Fellow) The future outcome of a proposed investment is uncertain at the time the decision must be made to accept it or reject it. This uncertainty can be expressed in the form of a probability distribution. An attempt is made to rationalize the investment decision under these circumstances, especially when the range of possible outcomes extends into both the acceptable and unacceptable domains. A rigorous definition of risk is proposed, and a criterion of risk aversion is developed that forms the boundary between acceptable risk and unacceptable risk (called the loss limitation line). It is shown that this decision criterion can also serve as a quantitative yardstick in the evaluation of various possibilities for 'tailoring' the proposal to mlke it more compatible with the particular financial circumstances of the company concerned.

Jan 4, 1976

By R. H. Steel

Ingot casting and wire drawing In Iron Age Southern Africa by R. H. STEEL (Visitor) This paper describes the experiments that were conducted in 1974/1975 on two related aspects of Iron Age copper technology in Southern Africa: ingot casting and wire drawing. Three types of ingot were successfully cast: the St Andrew's Cross ingot, the marale ingot, and the musuku. It is suggested that the 'studs' on the musuku are not the remains of broken-off rods as previously proposed by other investigators, but that the ridged pattern is an ornamental feature. Copper wire was successfully drawn with similar tools and according to the procedures described in the literature on African Iron Age wire drawing. It is concluded that these accounts are generally accurate and that the pre-European metal workers are worthy of respect for the results they achieved with primitive methods.

Jan 11, 1975

By B. Geelhoed

A generalization of Gy?s 1979 model for the variance of the fundamental sampling error has been proposed at WCSB2?2005 by Geelhoed. This generalized model can potentially lead to a better correspondence with actual sampling processes. However, a new parameter is required by the new model: ?the parameter for the dependent selection of particles?(Cij). It is important that this new parameter, which is at the basis of the new theory, is well understood in the sampling and blending community. In order to clarify the meaning of Cijand to prevent potential misinterpretation of Cij, we discuss the difference between Cij and an intuitively associated, but different, parameter: ?the parameter for the dependent selection of particle types?(Mij). In this contribution, the theoretical difference between both parameters is clarified. Simulations demonstrate that, numerically, the difference between Cij and Mij can be large. Some additional advantages of the approach which uses Cij are discussed: (i) the approach based on Cijis more general; (ii) in all cases where Mij is known, Cij can be determined as well, while the reverse is not true; (iii) an equation already exists that relates the sample variance to the value of Cij.

Jan 1, 2009

A 36-year-old A-S-H pump, manufactured to designs dating back to 1936, was recently presented to the Gold Mine Museum by Envirotech. The pump, a B-frame three-piece rubber-lined Hydroseal unit, was supplied by Envirotech's predecessor company, Denver Machinery, and was installed by South Roodepoort Main Reef Areas Limited on 22nd March, 1948. Metals, materials, manufacturing The 37th Annual Conference of the Australasian Institute of Metals will be held in Ballarat (Australia) from 13th to 17th May, 1985. 1985is the Sesquicentennial year of Victoria, and for the first time the historic City of Ballarat has been chosen as the venue for an Australasian Institute of Metals congress. Steel rolling Conferences on steel rolling, sponsored by The Iron and Steel Institute of Japan (ISH), and supported by iron and steel institutes in many countries of the world, have been held since 1980. The first conference was held in Tokyo in 1980, sponsored by The Iron and Steel Institute of Japan.

Jan 1, 1984