Search Documents

By F. W. Penn

An aircraft auxiliary power unit (APU) was used as an exhaust source for evaluation and refinement of sampling and analytical procedures for gas turbine engines. The unit was also used to determine the emission characteristics of APU's in service and to study the effect of fuel composition and combustor design on exhaust emissions. Carbon monoxide, carbon dioxide, oxides of nitrogen, hydrocarbons, aldehydes, particulate loading, and odor were measured at engine operating modes representing the duty cycle encountered in airline operation. Analyses showed good repeatability, and adequate sensitivity was attained in these experiments. Smoke opacity measurements were not taken owing to the lack of a high-sensitivity smokemeter. Results showed that the minimum emission levels occurred with the standard combustor and Jet A fuel. Emission rates were highly dependent on test mode, but emission patterns as a function of test mode were similar for all fuels and combustors tested. A comparison of three identical design production combustors showed a variation in average emission rates of less than 5 pct.

Jan 1, 1973

By W. L. Staker

Alternatives were developed to the conventional ammoniacal carbonate leaching-steam stripping procedure for recovering copper as an oxide from contaminated scrap metal. By entraining air bubbles in the leach solution, the copper dissolution rate was increased to 1.5 g/in2 of copper surface per hour, compared to 0.5 g/in2/hr produced by conventional agitation in stirred tanks. Using entrained nitrogen gas bubbles for agitation in conjunction with powdered sulfur not only resulted in rapid dissolution but also simultaneous precipitation of the copper from solution as a high-grade cuprous sulfide.

Jan 1, 1971

By George J. Conroy, Angel G. Jordan, Eugene W. Bartel

Time-domain reflectometry has long been an accepted and used method for locating electrical faults in electrical cables. The process has, however, required the use of equipment that is somewhat complex and difficult to use. The skill level needed to operate such equipment is high. Therefore, the use of the time-domain reflectometry process has been limited to selected locations and controlled environments. The process, however, has great potential for mine system applications. The ability to locate and repair trailing power cable without removing it from the mine would result in great savings in cost and employee-hours. Therefore, an automatic microprocessor-controlled time- domain reflectometry system was developed to reduce process complexity and skill level needed to operate the unit. The theory of operations is discussed along with the computer analogies used in the unit. The present unit capabilities are presented and future areas of application and research are discussed.

Jan 1, 1979

By C. M. Mason

A method for evaluating the relative incendivity of detonating cord in natural gas-air mixtures was developed. The method consisted of firing short lengths of cord in bundles to determine the number of strands per bundle which would ignite natural gas-air mixtures 50 percent of the time in the 45-cubic-foot gallery of the Bureau of Mines. The relative efficiency of a flame quenching agent, potassium acid tartrate (KHT), when incorporated in both the pentaerythritol tetranitrate (PETN) core and the polyethylene sheath, was explored. The effects of sheath thickness, sheath composition, core weight, and core composition were evaluated. The bundle method established a quantitative scale for evaluating the relative incendivity of cords. The relative incendivity determined by the bundle method was then compared with the incendivity of 100-foot lengths of detonating cord when initiated in 8 percent natural gas in the 640-cubic-foot gallery of the Bureau of Mines.

Jan 1, 1968

By W. F. Marshall

The effect of engine parameters on exhaust emissions from two diesel engines was studied experimentally. Fuel-injection characteristics and intake air conditions were considered as parameters influencing the emissions. Emphasis was placed on the effect of parameter variations on nitrogen oxide (NOx) emissions, because diesels generally emit very low levels of carbon monoxide (CO) and unburned hydrocarbons. Emissions other than NOx were at lowest levels when the engines were adjusted for best performance. NOx emissions can be diminished somewhat through variation in fuel-injection characteristics, but there generally are penalties in emissions of CO, smoke, and unburned hydrocarbons or in engine performance. Temperature and composition of intake air have a significant effect on NOx emissions. Levels of NOx are reduced by recirculating the exhaust gas or by adding water to the intake air stream. However, the rate of water added or exhaust gas recirculated must be limited to prevent the degradation of engine performance and increased emissions of CO and smoke. At high exhaust recirculation rates, levels of CO and smoke were increased such that it was necessary to derate the engine and also to use a catalytic system for oxidation of CO.

Jan 1, 1971

Provide the U.S. mining industry with the means to measure and control exhaust emissions of diesel engines used in underground mines. Approach Diesel research is divided into four primary areas: exhaust aerosol measurement, particulate control, gaseous emission control, and chemical and biological characterizition of particulate matter. Diesel research is frequently cosponsored by industry; collaborative research ventures between industry, academia, other government agencies, and the Bureau arc common. Diesel research at the Bureau is conducted in the diesel engine research facility at the Bureau?s Twin Cities Research Center (TCRC). This facility is a state-of-the-art laboratory capable of performing emissions testing, exhaust control evaluations, and safety tests. Background Exposure of mine workers to airborne contaminants from diesel engine exhaust is potentially harmful. The National Institute for Occupational Safety and Health has recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen" and that ?reductions in exposure to diesel exhaust in the workplace would reduce the risk." The U.S. Mine Safely and Health Administration (MSHA) convened an Advisory Committee on Standards and Regulations for Diesel-Powered Equipment and is beginning to implement its recommendations, which cover health, safety, and certification and approval issues surrounding the use of diesels underground. In January 1992, MSHA published an advance notice of proposed rulemaking to regulate diesel particulate matter in underground mines.

Jan 1, 1992

Reduce the airborne dust generated in a longwall coal face. Approach Reduce the rotational speed and increase the depth-of-cut of the longwall shearer. How It Works An Anderson-Mavor AM500 double-ended ranging drum shearer was fitted with drums specially designed to accept the large picks required for this testing program. Change gears In the shearer allowed rotational speeds of the drums to be set at 35, 45, 55, or 70 rpm. As deep cutting removes larger coal fragments, the specific energy requirements of the operation are reduced and less surface area results. Dust generation and shearer power consumption are also reduced. The lower rotational speed minimizes the fanning action of the cutterheads and thus reduces the amount of coal fines that become airborne.

Jan 1, 1981

Provide the mining industry with an easy-to-use means of accurately predicting surface subsidence caused by longwall mining in the northern Appalachian Coal Basin. Approach The Bureau of Mines developed a subsidence prediction model using the novel approach of a variable subsidence coefficient. This approach had to be used because of the resistant strata types which commonly occur within the relatively thin overburden material typical in northern Appalachia. Such resistant strata precluded the use of the popular European methods that assume homogeneous overburden or overburden behaving as homogeneous from a subsidence point of view. The model is available in a BASIC computer program for use on most personal computers. The user has the options of obtaining individual subsidence calculations or may choose to develop a subsidence profile using an average overburden value. The program output can be generated in graphic or tabular form showing the location of the surface point with respect to the longwall panel edge, overburden depth, and the subsidence value.

Jan 1, 1986

By W. F. Hughes

The thermodynamics of an electromagnetic field-fluid interaction system is discussed. A review of the thermodynamics of linear media (the permittivity and permeability taken as functions of density and temperature) is presented; then an extension is made to nonlinear media (the permittivity and permeability taken as functions of the fields). Expressions for thermodynamic properties and reversible work are derived and the first law of thermodynamics for magnetohydrodynamic flow is discussed.

Jan 1, 1968

By Vijia K. Karra

Making sure workers within the aggregates industry go home safely each day is the goal of aggregate companies throughout the United States. At the National Institute for Occupational Safety and Health (NIOSH) researchers are contributing to NIOSH’s vision of safety and health through a fact-finding approach to reducing injuries/illnesses in various mineral sectors. Surveillance data from the Mine Safety and Health Administration (MSHA) has been the primary source for such analyses. It helps to focus research efforts on key machinery, workers, and their tasks. The crushed stone category referred to in this article is represented as crushed and broken stone in the MSHA database.

By J. E. Chilton, C. R. Carpenter

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro- chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1- to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light- emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 1992

By Harry Dobroski, Larry G. Stolarczyk

Medium-frequency (MF) techniques have been successfully .[pplied] to the problem of radio voice communications in both coal and metal and nonmental mines. Long range is achieved by taking advantage of existing mine conductors that carry and propagate the signal over vast areas. It is very likely that in the near future such systems will become the referred method for general mine communications. MF techniques can also be applied to the areas of in-mine control and monitoring. Preliminary work in this area is described. In a western mine, locomotives are being operated under MF remote control in a loading operation. In several eastern mines, MF has been evaluated as a method for monitoring the status of devices in remote areas of the mines. All control and monitor information uses existing mine conductors.

By Forrest T. Moyer

General injury experience in the mineral fuel industries was less favorable in 1965. Of the major industry groups, the coal mining and the coke industries had higher injury-frequency and severity rates than in 1964. The oil and gas industries had an increased Tate of occurrence of injuries although the severity rate improved. However, in the relatively small peat and native asphalt industries, the injury experience was more favorable than in 1964. Overall operating activity for the mineral fuel industries, as measured by the average number of men working daily and the total worktime, was higher than in 1964. Moderate declines in employment and worktime in the coal and peat industries were more than offset by gain in the other groups. In addition to the industry classifications included in this chapter, similar injury, employment, and worktime data on the metal, nonmetal, stone and aggregate industries are presented in volume I. Corresponding data for broad classifications of mineral industry groups arc given by States in volume III of the Minerals Yearbook.

Jan 1, 1967

By Franxis Church Lincoln

"INTRODUCTION During September 1944, the Bureau of Mines undertook a program of investigation and limited exploratory drilling at the Last Chance mine, near the village of Arthur in Grant County, Wisconsin, as part of a general investigation of the zinc-producing area of southwestern Wisconsin when every effort was being made to increase the production of metals important to the Nation's war program.The Bureau's attention was directed, to the Last Chance mine when the operators discovered high percentages of zinc in an exploratory churn drill hole a short distance southeast of the mine. The ore was found in the Trenton Limestone, which underlies the ore horizon then being mined. To determine whether this discovery was important, and to demonstrate the possible extension of the ore the Bureau of Mines drilled five additional holes in the vicinity of the discovery.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report."

Mar 1, 1947

By Thomas V. Falkie, R. Venkataramani

The empirical nature of this investigation required measurements of variables under operating conditions in underground coal mines. The variables to be measured were based on the postulated character¬istics of the loading function, as described in the previous chapter. One class of variables presumed to influence the loading function are geological variables. Accordingly, the sites for data collection were selected in different bituminous coal seams at dispersed locations in order that variation in geological conditions would exist. Seven mines in central and western Pennsylvania and one mine in northern West Virginia were selected as data collection sites. Five different coal seams were represented by these mines. The remaining classes of variables - geometric, mechanical, and procedural - were measured as they occurred in the mines. A description of the measurements, and the conversion of these measurements to forms which could be-analyzed for effect on the loading function is given. Mining Dimensions At the underground working face, the following dimensions were measured: a. Thickness of coal excavated. b. Thickness of shale excavated. c. Total height excavated. d. Width excavated. e. Depth of penetration of each machine cut. With the exception of the last of these dimensions, all were measured

Jan 1, 1972

By Thomas V. Falkie, R. Venkataramani

1. Summary This investigation is concerned with description of the loading function at the underground coal face, and the identification of varia¬bles - geological, geometric, mechanical, and operational - that affect the loading function. The immediate objective of this work was to provide information for operations-research studies as applied to underground coal mining, and the broad objective was to provide guide¬lines for planning and equipment selection in underground coal mining. The loading function was expressed as -a statistically-developed linear mathematical model. Originally, fifteen independent variables were considered which potentially could have influenced the loading function. These variables were constructed on the basis of measurable or estima¬ble geometric and geological properties at the working face, mechanical characteristics of the mining machine, and certain operational proce¬dures of mining. The original model explained 64.0 percent of the experimental variation. The final condensed model explained 54.1 percent of the experimental variation in terms of only five indepen¬dent variables, namely: 1. Ratio: width of cut/total width of cutter 2. Ratio: height of cut/diameter of cutter 3. Total horsepower of cutter-drive motors 4. Rotation speed (RPM) of cutter 5,. A subjective estimate of machine quality and operator skill Certain limitations were found to exist in the evaluation of the variables. Principle among these limitations was the impossibility of precise measurement of tonnage loaded in certain instances.

Jan 1, 1972

By Sabri Ergun

The method of constant compositions involves the determination of the time required for the attainment of a given conversion at various temperatures. Heretofore, it has been used in evaluating the energy of activation only. A development of the method, made in the present study, makes possible the evaluation of the functional dependence upon composition and the frequency factor in addition to the energy of activation. INTRODUCTION Kinetics of reactions are best analyzed in the light of the mechanism, energy requirements, and forces involved in the reaction. Such physico-chemical information is not often available in solid state phase transformations. The reaction rates are followed by changes in a physical property during the course of the reaction, and repeating the experiment at different temperatures permits the determination of activation energy only. The possibility of a complete kinetic analysis by such a purely "phenomenological" approach has been questioned.4/ In this report a method is developed making possible the evaluation of the functional dependence upon composition and frequency factor in addition to the energy of activation. The application of the method to a study of solid state order-disorder changes is demonstrated.

Jan 1, 1960

By George Bockosh

Mr. Bockosh is an electrical engineer with the U.S. Bureau of Mines In Pittsburgh, and has devoted the last two years to research on underground illumination. He formerly was a mine maintenance foreman and worked two years underground. He is a graduate of the University of Pittsburgh, where he is now working toward his masters degree in mining. When Congress first legislated light in American coal mines, it was a little like mandating a walk on the moon before the first satellite had been put in orbit. It was never a question, of course, of whether it could be done. But no one knew quite how. It's one thing to string a few light bulbs, and quite something else to provide uniform, sufficient, safe and reliable illumination, with fixtures that will hold up under some of the toughest conditions in the world - in the life-and-death circumstances of a craggy, black cavern filled with dangerous, moving machinery. In fact, in 1969 when Congress originally mandated illumination standards for the work places of underground coal mines, no one even knew just how much light was needed. That question was answered within a year by the National Bureau of Standards. In a study commissioned by the U.S. Bureau of Mines, the Bureau of Standards determined that underground mine should be illuminated with a light intensity of 0.06 foot-lamberts, a measurement of light reflected from surfaces in the lighted area-as opposed to foot-candles, a measurement of light from the source of illumination-in order for miners to adequately see what they are doing. That study was followed by more detailed research done at the Bureau of Mines' direction by the Research and Development Department of the Naval Ammunition Depot in Crane, Ind. This work evaluated the specific lighting needs of miners engaged In more than 100 different job tasks in all three types of coal mining- conventional, continuous and longwall. The Naval Depot report brought forth nearly 300 pages of detailed lighting data and concluded that proper illumination of mine work areas would serve more than just the cause of mine safety.

Jan 1, 1976

By Ernest W. Loya

A method for preparing gravimetric primary standards of helium in the parts per trillion range has been developed by the Bureau of Mines. The standards are used to calibrate a specially modified mass spectrometer used in determining the abundance of helium-3 and helium-4 in geochemical samples and of helium-3 in isotopically purified helium-4. The desired gas standards are prepared in 5-kg metal cylinders filled to 1,800 psia. Relative errors of less than 1 pct have been attained in the parts per trillion range using a successive dilution technique.

Jan 1, 1982

By R. Sainath, Wils L. Cooley

Continuous monitoring of ground bed resistance is essential to insure a low-resistance path for fault currents, lightning strokes, and electrostatic discharges. This paper explains the salient features of the continuous ground bed monitor and its applications. The importance of a low-resistance path to ground is highlighted. Sample readings obtained with the ground bed monitor are included, and typical applications of this instrument are illustrated. This effort was supported by the U.S. Department of Interior's Bureau of Mines under USBM grant G0144138.

Jan 1, 1979