Search Documents

By Jack E. Fraley

Magnesium oxysulfate cement has been specially formulated as a sealant in underground coal mines for reducing sloughing of shale roofs and coal ribs, for reducing air losses through block stoppings, for constructing sprayed stop-pings over approved jute cloth or metal lath, and for reducing combustibility of polyurethane foam. A standard spray machine (Mining Enforcement and Safety Administration (MESA) approved) was used for the underground testing. Our research shows that a 1/2-inch coating reduces shale and coal sloughing, reduces air losses through block stoppings, and prevents fire propagation through a metal tunnel lined with polyurethane foam. During the underground tests, excess mixing water was used to improve pumping the slurry to the spray nozzle. This was later found to increase shrinkage cracks in the cured coatings. Controlling excess water is important to an acceptable coating.

Jan 1, 1976

By James H. Scott

A technique of seismic refraction data analysis has been developed in which a digital computer is used to generate a two-dimensional model representing a layered-earth depth interpretation. Travel times are picked on seismic records by the human interpreter. These times, together with shot point and geophone locations and refraction layer control information, are submitted to the computer on punched cards. A first approximation delineation of each refraction horizon is obtained by a computer adaptation of the delay-time method. The approximation is then tested and improved by the computer through the use of a ray-tracing procedure in which ray travel times computed for the model are compared against field-measured travel times. The model is subsequently adjusted in an iterative manner so as to minimize the discrepancy between computed and measured travel times. The Fortran program is listed in the appendix of the report together with instructions for preparing data cards and examples of results.

Jan 1, 1972

By Ted C. Briggs

Equations for the elastic pressure distortion of the volumes of a Burnett compressibility apparatus are developed and presented in this report for volumes under internal and external applied pressures. An experimental method for the determination of the external pressure distortion coefficients is presented. Young?s modulus and the internal-pressure distortion coefficients are computed from the experimentally determined external-pressure distortion coefficients. The temperature dependence of the pressure distortion coefficients and of Young's modulus is evaluated for the temperature range 0° to 80° C.

Jan 1, 1968

By C. L. Karr

The U.S. Bureau of Mines is optimizing the design of an air-sparged hydrocyclone. This report summarizes the initial stage of the project-the prediction of collision efficiencies for use in a comprehensive air-sparged hydrocyclone model. The equations of motion are presented in nondimensional form and solved numerically for a small spherical particle passing around a larger bubble in an infinite fluid under the influence of a strong force field. Collision efficiencies are determined from the calculated particle trajectories for values of Stokes' number, K, between 0.01 and 100 and for values of the nondimensional force, W, between 0.0 and 100. These large values of K and Ware needed to model high-performance flotation devices like the air-sparged hydrocyclone; solutions for the required K and W values have not appeared in the literature prior to this study. Effects of changes in particle-to-bubble radius ratio are considered for both viscous and potential flows. The results help predict the improved recovery of fine particles when flotation is performed in a strong force field.

Jan 1, 1990

By Joseph V. Mather, E. H. McCleary

"INTRODUCTION Workmen are transported in shafts in various types of cages or skips, most of which were designed primarily for hoisting cars and materials. Therefore, in general the cages or skips are not completely enclosed, adequate and gates are not always provided, and at many mines signaling devices and telephones are re¬stricted to those at the various landings in the shafts.Shaft accidents are usually severe - frequently fatal - and as a rule such an accident is caused by failure to comply with company rules or by ignoring them.Sixty men were killed and 555 men were injured in shafts of the anthracite and bituminous coal mines of the United States during the 5-year period 1938-42. 4/ Many of these accidents could have been prevented by having properly enclosed cages and adequate locking devices on doors to prevent workmen from falling into the shafts.The officials of the Heidelberg Coal Co. contemplated utilizing an old coal-hoisting shaft as a man-hoisting shaft; however, it was their desire to avoid the use of the conventional cage and to try to provide a safer means of transporting men in the shaft. Investigations and studies made by the officials revealed that an elevator similar to those used in large buildings would be more economical in first cost, maintenance, and operating costs would be less, and it would be safer and more convenient for the workmen. Effective safety devices for such elevators have been developed to such a high degree that those properly installed seldom fail. The elevator or man cage finally chosen cannot be pulled above the top landing through mechanical or man failure; it stops automatically at each landing and cannot be moved while a door is open; when the cage leaves the landing the doors opening to the shaft are automatically locked by mechanical and electrically operated locks; electric lights, telephone communication, and push-bottom controls are available on the cage, and adequate safety switches and overspeed controls are provided."

Jun 1, 1947

Provide an accurate, reliable means for determining when a sealed mine or mine section can be safely reopened after a fire. Approach The Bureau of Mines performed a research investigation that resulted in the development of a mathematical formula for deriving a quantity, called RATIO, which can be used to define when a sealed mine or mine section has returned to safe recovery conditions after a fire. Research Results There were two major results from this Bureau research. Over a period of several years, the Bureau of Mines conducted six experiments at its Bruceton Experimental Mine in Pennsylvania. The experiments involved sealing the mine after several tons of piled coal had been allowed to burn continuously for 2 to 3 days. Although gas data obtained during the experiments revealed nothing significant, measured smoke particle levels were found to correlate with the stages of combustion and temperatures of the smoldering coal pile. Moreover, it was found that no smoke particles are produced when high-temperature smoldering exists deep within the mass of the coal pile since the smoke particles are filtered by the coal surrounding the hot region. Smoke is emitted into the mine atmosphere only if combustion is occurring near exposed surfaces. As suggested by these findings, any decision to recover a sealed mine area based primarily upon the absence of smoke particles is not a wise derision.

Jan 1, 1988

By Jack C. White

The purpose of this Bureau of Mines work was to develop information useful in improving copper recovery during copper milling operations. Eleven copper mill tailings from the Western United States were subjected to froth flotation and cyanide leaching to provide an experimental basis for comparing their beneficiation response. Recoveries in flotation concentrates made from mill tailings ranged from 65 to 15 percent, at copper grades of 13 and 2.2 percent, respectively. Liberated copper sulfide minerals present in two samples were readily recovered by laboratory froth flotation. Nine of the samples were less amenable to froth flotation because of physical locking between copper sulfide minerals and gangue. Correlations among tailings indicated that recovery of sulfide copper by flotation was directly related to the sulfide copper content. Empirical equations derived from flotation data provided average values for unrecoverable copper and for recovery efficiency. Flotation response of copper mill tailings may be predicted from the equations. Data from cyanide leaching provides an equation describing the limiting high values for removal of copper by this method.

Jan 1, 1974

By James W. Townsend, William H. King

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Alisman, chief, Salt Lake City Division, Mining Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon ore such technique.The Wright borehole-surveying instrument developed at the Homestake mine, Lead, S. Dak., has been described in several publications. 3/ For the benefit of those to whom the publications are not available, the instrument is described here. However, this article will be concerned mainly with the technique developed by the Federal Bureau of Mines for using the instrument.In the use of the Wright borehole-surveying instrument, it was found advantageous to develop a standard practice of operation covering type of film, preparation and care of film, loading film in instrument, placing instrument in container, exposure time, unloading film from instrument, development of film, and determination of dip and strike from film impressions."

May 1, 1947

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

INPUT FORMAT INSTRUCTION FILE FOR PROGRAM MFIRE GENERAL RULES FOR DATA INPUT: $THERE IS NO NEED TO DISTINGUISH INTERGER AND REAL NUMBERS. $ $ SYMBOLS FOR NUMERICAL INPUT INCLUDE THE FOLLOWING $ $ 1234567890 -+BLANK $ $ * FREE FORMAT IS ALLOWED. COMMA AND BLANK SPACE CAN BOTH BE $ $ DELIMITERS. SEQUENTIALLY DISTRIBUTED BLANK SPACES ACT AS ONE $ $ DELIMITER. BLANKS ADJACENT TO A COMMA HAVE NO DELIMITING EFFECT $ $ * A ZERO INPUT CAN BE OMITTED BUT NOT THE DELIMITERS EXCEPT WHEN $ $ THE ZERO INPUTS ARE THE LAST ONES ON A LINE. $ $ * A LINE WHOSE FIRST NON-BLANK SYMBOL IS "$ IS AN INSTRUCTION $ $ LINE WHICH WILL BE IGNORED IN A PROGRAM RUN. $ $ * A LINE WHOSE FIRST NON-BLANK SYMBOL IS NEITHER ONE USED IN THE $ $ ABOVE LIST FOR NUMERICAL INPUT NOR "$, OR WHICH CONTAINS MORE $ $ THAN 3 SYMBOLS OUTSIDE OF THE LIST, IS A COMMENT LINE WHICH WILL $ $ BE SHOWN IN THE OUTPUT FILE. $

Jan 1, 1990

Provide mine operators with a quick means of identifying the effect of cutting system changes on relative dustiness at the mine face, by developing an interactive computer program for drum-type coal mining machines. Approach A program which simultaneously evaluates machine parameters, coal seam parameters and mine operator-controlled parameters for their effects on relative dustiness has been developed for use on any minicomputer using BASIC computer language. How it works The interactive computer program allows mine operators to make one or more changes at a time to their cutting system to determine how these changes affect relative dustiness of the face. Using this program, mine operators can find the optimum cutting system configuration to minimize dust using their seam conditions and their equipment specifications. The mining machine variables include: number of vane bits, number of gage bits, number of starts, vane wrap, number of end ring lines, rpm, advance rate, ton/min, percentage of time spent cutting per shift, and airflow.

Jan 1, 1986

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

8. Refuge Chambers 8.1 Refuge Chambers - Technical Discussion 8.1.1 Introduction As a part of the overall escape system, refuge chambers can provide a last resort when existing escapeways are blocked. These chambers are intended to provide both protection from toxic gases and a life supporting environment for a period of time before external rescue or further escape efforts can be carried out Escapeways may be blocked physically (due to cave-ins, etc), by fire, or by the presence of a toxic or oxygen deficient atmosphere. In the first two cases, the trapped miners would most likely await external rescue efforts, and hence the design of the chamber will have to consider the time durations that such efforts may take, It is also possible, in the second case, for fire fighting and fire protective equipment to be stored in the chamber so that miners may attempt their own escape. In the third case, it should be recognized that a compact, beltmounted 1-hour self-contained breathing apparatus has been developed(9), and that other, less compact equipment is available for up to 4 hours of self-contained breathing supply. If such equipment were stored in the chambers, then miners could escape by travelling from chamber to chamber, taking temporary refuge in each before proceeding to the next. 8.1.2 Background The concept of "barricading" has long been recommended for those emergencies where miners are trapped inby a fire. Barricading, which is the construction of a makeshift shelter in a crosscut or deadend, protects the entrapped miners from toxic gases and enables them to conserve a supply of air. In this manner, they can survive two or three days--hopefully enough time for them to be reached by rescue teams. In the past, many lives have been saved with this technique.

Jan 1, 1976

By P. D. Bergman

To assess the efficacy and economics of producing power from coal, four open-cycle magnetohydrodynamic (MHD) processing schemes were selected for study. Each involved a different mode of coal combustion and level of gas cleanliness. The options considered were: (1) coal burned in a slagging combustor; (2) suspension gasification with slag removal prior to combustion; (3) parallel cyclone combustors, one operating fuel rich and the other operating with excess air; and (4) suspension gasification by the hot exhaust gases from the MHO duct with ash removed prior to combustion. Option 1 has the highest ash content in the combustion plasma and as a result would have the greatest operational difficulties associated with it. Options 2 and 4 have the cleanest MHD combustion plasma. For coal priced at $4/ton, the power generating cost of option 4,11.78 mills/Kw-hr, is the highest, with Option 1, at 9.04 mills/kW-hr the lowest. These costs may be compared with a conventional power cost of 9.92 mills/kW-hr for the late seventies. Capital costs of three of the four options were competitive with those of conventional thermal power plants employing stack gas S02 cleanup systems. Option 2 has the most favorable combination of operating characteristics and power cost. It was concluded that a clean, high-temperature working fluid can probably be produced from coal without leading to depressed system efficiencies and exorbitant capital costs.

Jan 1, 1973

By H. V. Makar

A study was conducted by the Bureau of Mines to determine problems associated with the use of ferrous fractions from urban refuse as melting stock for steelmaking and to evaluate the resulting steel products. The study involved 50-pound ingots from laboratory melts and 50-pound ingots from 1-ton electric-arc-furnace melts. The 50 pound ingots from the laboratory melts and the arc-furnace melts were hot rolled to provide material for mechanical and corrosion testing. Results obtained in the study include the following: Most steels rolled successfully and exhibited acceptable surface and edge condition. Tensile strengths of the plain carbon steels were not significantly affected by copper up to concentrations of 0.65 pct and were not affected by tin content up to 0.16 pct. Yield strength increased with increasing copper and tin contents, and impact strength decreased with increasing tin content. Hardness increased slightly with increasing copper content. In general, properties of the steel produced were not measurably affected by charge composition (that is, melting stock), melting practice, or method of scrap preparation.

Jan 1, 1975

By Edward P. Barrett

[Iron oxides, when reduced at temperatures below 900° form a dark gray substance, very porous bait otherwise in almost the same form as the original particles. In the temperature ire range of 1,000 to 1,100° the product is pertly sintered but still shows the outlines of the original particles. Those products are known as "sponge iron." At temperatures of 1,100 to 1,2000 the metallic iron begins to flow together and to a semifused, pasty, porous mass called a "bloom," which can he worked under a hammer to form a product similar to wrought iron; it contains slag inclusions and is too low in carbon to make steel. If the temperature is 1,300 to 1,300°, part of the iron will fuse enough to absorb more carbon. The dissolved carbon lowers the melting point and still more carbon is absorbed. The melted portion acts a flux for the unmelted metallic particles until the entire mass becomes a high-carbon fluid known as "cast iron." Sponge iron was probably the form in which the first iron was recovered from the ores. As early as the eighth century the Catlan forge3 developed into a low-shaft furnace known as the "high bloomary," in which iron eras produced in the form of a pasty mass. In 1340 the first blast furnace was built in Belgium. The greater part of the iron was made into wrought-iron blooms by crude puddling processes. Charcoal was used as the fuel until tie latter part of the 17th century when coke was used in England. In 1865 Bessemer built his first converter in. England, and within a few years the Siemen's regenerative open-hearth furnace was developed, also in England. Enormous expansion in the metallurgy of iron followed. The idea of "direct processes" for the production of iron arid steel has persisted throughout all this time. The production of steel from sponge iron has theoretical advantages over the present-day standard methods, and handreds of so--called "direct processes" have been proposed or tried during the past century.4]

Jan 1, 1929

By Raymond F. Helinski, Linda J. McWilliams, Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

This report examines the boom arm vertical speed for roof bolting machines to study a moving boom arm appendage at different speeds during different work scenarios. The goal of this study is to determine the impact of the appendage speed on the likelihood of the operator's hand, arm, head, or leg making contact, such as touching the moving appendage. The overall research goal is to reduce workers' risks to injury from exposure to underground mining machinery. Accident investigation reports from the Mine Safety and Health Administration do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are not feasible because of safety issues. As an alternative, researchers used a unique computer simulation model that uses a virtual human, vision tracking, and generates random virtual human motions and risky work behaviors. By using specialized software to simulate the computer model, researchers accurately identified potential hazards of tasks where it is not possible to perform experiments with human subjects. Results of a frequency distribution analytic approach show that, regardless of other variables, contact incidents were always greater when the boom was moving up, always greater on the hand, and always greater or the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom is ascending. Results of a cross-tabulation analytic approach show that the 25th-percentile operators experienced more contacts than other operator sizes and had most of their contacts during a boom speed of 13 in/sec. The hand-on-boom behavior during drilling and bolting tasks experienced more contacts than other work behaviors, and both tasks had most of their contacts during speed 13 in/sec. The 60-in seam experienced more contacts than other seam heights and had most of the contacts during speed 16 in/sec. For univariate logistic regression models, seam height is the most important predictor of the probability of a contact. However, a multivariate logistic regression model predicted contacts are more likely with the both-knee work posture in the 60-in seam, a 25th-percentile operator compared to a 55th-percentile operator, and speeds 16 and 22 in/sec compared to 7 in/sec. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speeds greater than13 in/sec result in a substantial increase in risk to the roof bolter operator making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Virtual operator's response time has little effect on the number of contacts experienced. The mining industry can use the information in this study to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

Jan 5, 2005

By C. D. Litton

Submicrometer particle concentrations and average particle sizes were monitored for four full-scale sealed coal fires in the multiple-entry section of the Bruceton Experimental Mine. The data from these tests indicate that there exists a very good correlation between the submicrometer particle concentrations and the maximum temperatures measured within the coalbed. As the maximum coalbed temperature decreases with time after sealing, the submicrometer particle concentrations show a corresponding reduction. This particle-temperature correlation is in sharp contrast to the gas concentration data obtained, for which essentially no correlation exists with the measured coal-bed temperatures. The results of these full-scale tests indicate that the measurement of submicrometer particle concentrations may be a more realistic approach to determining the status of underground sealed fire areas.

Jan 1, 1981

By David C. Oyler, Gregory Hasenfus, Gregory M. Molinda

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation stopping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented.

By F. E. Armstrong

The Bureau of Mines has conducted a research program to systematize the art of locating uncharted and lost oil and gas wells that penetrate coal seams; this publication presents a preliminary summary of its findings. Although no method or combination of methods will guarantee finding all uncharted and abandoned wells in a particular area, at least 75 percent of such wells can be located by compiling and applying all available information and using modern metal detectors.

Jan 1, 1973

By Phyllip Worley, Frank E. Chase, Christopher Mark

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that “critical” sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

Provide the mining industry with a wireless surveying system for increasing efficiency in the drilling of methane drainage or exploration boreholes. Approach The Bureau of Mines has pioneered the technique of methane control by drilling long, horizontal drainage holes from within the mine complex. It was recognized during the early drainage projects that a major portion of the drilling operation was dedicated to hole surveying. In some cases more time was actually being spent on the surveying operation than on drilling. The large amount of time required for hole surveying was the result of having to pump an instrument to the bottom of the hole, then retrieve it with an attached wire line. Naturally as hole depth increased, so did the amount of time needed to perform the survey operation. If the survey operation could be improved it was obvious that overall efficiency in drilling of long, horizontal methane drainage holes would be greatly increased. The Bureau of Mines, therefore, developed, fabricated and tested in an operating coal mine a permissible wireless survey system specifically designed for small diameter methane drainage drilling. The prototype survey system was completed in 1982 and was given the IR-100 Award by Industrial Research and Development Magazine. A second generation survey system is currently being constructed using updated state-of-the-art electronic technology. The second generation system will be more portable, more reliable, easier to maintain, and less costly.

Jan 1, 1984