Search Documents

By J. M. Stuve

Provisional values for the heat of formation of europium trichloride and europium sesquioxide were determined by solution calorimetry utilizing europium metal of more than 99-percent purity. The resulting values for the heats of formation of Eu203 (cubic) and EuCls (hexagonal) were -386,970 ±l,200 cal/mole and -218,740 ±650 cal/mole, respectively, measured at 298.15° K.

Jan 1, 1965

By E. D. Eastman

The recent determination by Eckman and Rossini of the heat of formation of sulphur dioxide appears to be of much greater accuracy than any previous measurement . The value obtained by them , 70,940 cal . , is in good agreement with that of Thomsen ( 71,080 ) , but differs by about 1,700 calories from Berthelot's result ( 69,260 ) , and by 1,940 calories from the provisional figure ( 69,000 ) adopted by Lewis and Randall in their studies of the free energies of the sulphur compounds . This large discrepancy suggested the desirability of a recalculation of the free energy of sulphur dioxide . In addition it is now possiblt to fix the specific heat of S₂ gas with greater certainty than at the time of the original calculations . These two changes are incorporated in the recalculations described below , and directly affect the values of AH , and the Ar terms in the free energy equation . In the determination of the integration constant of the latter equation , the free energies and specific heats of water vapor and the oxides of carbon are required as auxiliary data . In this work these are based , with certain exceptions , upon the equations previously deduced , which differ appreciably from the corresponding equations of Lewis and Randall . 56 · The principal equilibria employed below , and the plan of calculation , remain the same as in the calculations of Lewis and Randall . Before beginning this revision a search of the literature was made , extending to August , 1930 , for studies of additional equilibria . Only one reaction was found that gives promise of increased accuracy . This is the equilibrium of sulphur dioxide with copper , cuprous oxide , and cuprous sulphide . In this case , however , certain of the subsidiary data are lacking , and until they become available , the existing studies of the equilibrium in this system can not be successfully utilized . The changes in the numerical data mentioned above , especially in the thermochemical constants , are therefore solely responsible for the rather significant differences of the revised from the original values of the free energy .

Apr 1, 1931

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Guatemala has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State.

Oct 1, 1929

By K. K. Kershner

Important contributions can be made to conservation of natural resources by recovering mineral values from primary and secondary metallurgical slimes and flue dusts. This applies particularly to ultrafine mineral particles that escape recovery by conventional mineral dressing. In the interest of economy and conservation the Bureau of Mines is investigating fundamental properties of ultrafine mineral values in slimes as a means of developing new or improved methods of mineral recovery. The work described in this progress report was carried on in the Bureau's laboratories at Rolla, Mo., from 1951 to 1953. The mineral material used as a subject for study was tin-ore slimes. DESCRIPTION OF TIN SLIMES The tin slimes consist principally of quartz, with appreciable quantities of tourmaline and sericite mica and small amounts of cassiterite, pyrite, hematite, and arsenopyrite. The tin content is approximately 0.5 percent.

Jan 1, 1954

Active and abandoned mine sites can be an irresistible- - and sometimes deadly - - draw for outdoor enthusiasts, particularly children and young adults. Despite repeated warnings, posted signs, and fencing, tragedies involving accidents on active and abandoned mine property continue to make headlines, especially with the arrival of warmer weather and the summer months ahead. Over the last few years, there have been dozens of tragic incidents involving children and adults ventur­ing onto active and abandoned mine property. They include: A 16-year-old youth suffered fatal injuries after his all-terrain vehicle became airborne in an accident at a gravel mine near Albany, New York. A young boy was electrocuted when he contacted a high-voltage power line while sliding down a stockpile at a sand and gravel mine in Grand Island, Nebraska during its off-shift hours.

Jan 1, 1999

By L. C. IlsLey

A specially recommended cable is a rubber-sheathed cable that has met the minimum performance requirements for cables as set forth in Schedule 20. The first in the series of recommended cables was listed September, 1930, by an ad- vance notice published as Information Circular 6375 which described the conditions under which the cable tests were made. Since that time six additional cables have met the test re- quirements and have been specially recommended. The complete list of specially recommended. cables is as follows: Specially recommended-cables Cable Symbol No. Hazacord No. 2 BM1 Stranding 19 x 7 Hazacord No. 3 BM2 do. Hazacord No. 4 BM3 do. Super-service No. 3 BM4 7 x 19 Super-service No. 2 Super-service No.. 4 BM5 do. BM6 do. Super-service No. 4 BM7 7x 7 Manufacturer Hazard Insulated Wire Works (division of the Okonite Co.) Do. Do. Rome Wire Company (division of the General Cable Corporation) Do. Do. Do. The cables listed were all twin (parallel duplex) cables having outer belts or cov- erings of approximately -inch high-grade rubber compound, and have the same general appear- ance and relative dimensions as the types of twin cables in general use. The cables were tested under conditions designed to show their approximate perform- ance under mine conditions. Only twin-type cables have met these test conditions. Although the recommended trailing cables are much better and safer for mine use than other cables and withstand being run over by a 7-ton car, they should not be considered as 100 per cent safe. The 7-ton car test represents the minimum limit requirement effective at present under Schedule 2-C, but the test car operates on a straight and level track, and thus does not represent the more severe conditions of mine use such as might result from uneven and curved tracks.

Mar 1, 1931

By John Durkin, Harry Dobroski

This paper presents a general overview of the Bureau of Mines' programs in the areas of operational and post-disaster communications. These programs encompass both hardware developments and system evaluations. Topics discussed include a new visual paging system compatible with existing pager phone lines, a means of modifying commercially avail able pager phones to permit selective paging and message leaving, a multiplexed telephone system that uses twisted shielded pair and requires no central control, medium frequency hardware developments, and a manual for mine communications. Research has continued in the area of post-disaster location and communications. This research is based on seismic and electro- magnetic techniques. Each has been extensively studied and field tested to better understand its ability to perform effectively. A brief description is given of the post-disaster program. Results are promising and provide insight into future areas of research.

New Continuous Personal Dust Monitors (CPDM) submitted to NIOSH for approval to sample coal mine dust must accurately measure respirable coal mine dust in mine environments. There are two steps in the process which may be done in any order. The manufacturer is required to submit the results of a comparative underground coal mine dust sampling study, where the candidate CPDM is compared to an approved coal mine dust sampling device (currently the Coal Mine Dust Personal Sampling Unit (CMDPSU)). This testing shall follow the guidelines outlined below and shall demonstrate through weighted regression analysis that the mean coefficient of variation with bias correction is equal to or less than 12.8%. The other step involves laboratory testing to determine the electronic and environmental stability. This testing must be conducted by a private, commercial, academic or other laboratory approved by NIOSH.

Jan 1, 2009

By M. Howard Berliner

"INTRODUCTION During the last 4 months of 1943, the Bureau of Mines engaged in an investigation and exploratory drilling program in the area between the Coughlin and Galena Level mines near the town of Shullsburg, in Lafayette County, Wisconsin. The work was undertaken as part of a general Bureau of Mines investigation of the zinc-producing area of southwestern Wiscon¬sin at a time when an effort was being made to increase the production of metals important to the Nation's war program.The portion of the southwest Wisconsin zinc district in the immediate vicinity of Shullsburg and the Coughlin and Galena Level mines is well mineralized. The principal ore horizon is at shallow depth, and there is evidence that relatively extensive surface mining for lead was done over a period of many years. Underground mining' for lead and zinc has continued to the present time.The Bureau undertook an exploratory drilling program in the area immediately west and southwest of the Coughlin mine workings after thorough preliminary investigations and geologic studies indicated that such work would serve to guide operators in the development of new ore reserves needed for continuance of mining operations in that area."

Apr 1, 1947

By L. C. IlsLey

Briefly, a permissible schedule of the Bureau of Mines establishes certain minimum standards for safety; it gives details of test methods adopted to determine whether these standards have been met, and a list of charges for such tests. Any manufacturer has the privilege of submitting his product for test in accordance with the conditions outlined in the schedules. His action is wholly voluntary, for the Federal Government has no jurisdiction as to what equipment shall be used in mines, this authority being left to the various States. When the product of a manufacturer has met the schedule requirements, he is permit¬ted to advertise this fact and to attach an approval plate with the bureau's seal to each machine he makes that is identical in every way with the equipment tested, inspected, and approved by the bureau. This work of approval has grown by the addition of new schedules until at present a great many mines are using one or more classes of permissible equipment, and there is still a demand for other approved apparatus in the ever-widening field of electrically operated machinery. The safety of electrical equipment of this type depends on four fundamentals, namely, (1) correct principles of design; (2) proper assembly of parts at the factory; (3) proper assembly and installation of equipment at the mine; (4) and proper operation and maintenance after installation. The first two factors are within the province of the manufacturer. The bureau either inspects and tests several models of one product, such as electric cap lamps, or one model, such as an electric motor. If this series of tests proves satisfactory, the manufacturer is given the privilege of making other appliances, and assembling them in the same way; the approval plate he attaches is his guaranty that the equipment is identical with the one tested and inspected by the bureau. The third and fourth factors concern those who use such permissible equipment, and it is to them that this paper is mainly addressed, in an effort

Jan 1, 1922

By Maurice Deul, Herbert H. Fields, John H. Perry

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (2), and pipeline--quality gas was introduced into a commercial pipeline. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed.

Jan 1, 1975

By D. E. Seizinger

Analytical methods for oxygenates in exhaust gases were studied, and emissions of these compounds from automotive engines were measured with and without an oxidation catalyst in the exhaust system. Hydrocarbons, simple mixtures of hydrocarbons, and a single gasoline were used as fuels. With the more complex gasoline, successful analysis was possible only with exhaust from the catalytic system which preferentially converted and thus removed interfering hydrocarbon species. However, it was shown that an estimate of the oxygenate yield from gasoline used in a noncatalytic system can be synthesized from data obtained with simple fuels. Such synthesized data were used for comparison of noncatalytic with catalytic systems. Compared with those of previous studies, results of this work indicate that the action of the catalyst introduced no new oxygenates and reduced both the carbonyl and the total of oxygenates. It is concluded that the compositional character and class distribution of oxygenates in exhaust from catalytic systems may differ significantly from the composition and distribution for oxygenates not subjected to catalytic conversion. The findings also support previous estimates that noncarbonyls may constitute a significant fraction of exhaust oxygenates and may warrant attention in procedures for measurement of the oxygenates.

Jan 1, 1973

By D. S. Kingery

The control of coal dust on coal tipples and cleaning plants has not been given the consideration that is afforded underground dust hazards. This apparent oversight is undoubtedly due to the general opinion that coal-dust accumulation in tipples or cleaning plants does not present the same type of hazard that it does underground. That this opinion is at least in part a fallacy has been proved many times, and the Bureau of Mines has on record many examples of explosions in tipples and cleaning plants.3/ In addition to this explosion hazard, coal dust is considered by sonic authorities to be injurious to the health of individuals exposed to it.4/ Obviously, it reduces visibility and contributes materially to accident hazards and the discomfort of the employees. Several companies have recognized this dust hazard and the advantages derived from controlling it; consequently, they have installed equipment to allay and control the dust on, their cleaning plants and tipples. The object of this paper is to. Summarize briefly some of the methods new in effect.

Jan 1, 1943

By Victor J. Lynch

The Andover-Sulphur Hill mines are 12 miles northeast of Andover and 5 miles southeast of Newton, in Sussex County, N.J. The property is situated on the Lehigh Valley and Hudson River Railroad and half a mile east of U.S. Highway 206. It is connected with the main highway by a hard-surfaced county road. (See fig. 1.) Howard J. Hewitt of Lafayette, N.J., has under lease the Sulphur Hill tract, consisting of 28 acres, and has an option on the Tar Hill tract of 106 acres. The Tar Hill property adjoins the Sulphur Hill on the northeast. (See fig. 2.) The Andover-Sulphur Hill property is owned by the Lenape Corp. of Andover, N.J., while the Tar Hill tract is owned by the Crane Iron Co. of Phillipsburg, N.J. These mines produced iron ore during a period of about 100 years but have not been operated since 1880. Zinc and lead sulfides occur mixed with iron ores in the lower workings of the old mines. A diamond-drilling program was recommended to determine the extent of the sulfide mineralization in depth and also to explore further the iron-ore deposits on the property. The project was started October 6, 1942, and finished November 25, 1942.

Dec 1, 1947

By Rollien R. Wells

A REPORT of technological advancements restricted to a specific 12-month period is impractical. Inherent in the nature and development of technology is the element of time; rarely can a new process or product be attributed to a particular year. An overall picture of general trends and pattern changes, however, is indicative of technological growth. This paper presents selected observations and discussions of current metallurgical research and practices in an attempt to develop' such a picture. Of the estimated $16.5 billion spent for research and development in the United States in 1962, at least 80 percent was earmarked for the aircraft, electronics, chemical, and machinery industries. Much of the effort was of the end-use variety and was oriented closely to the national defense and aerospace programs. Only a small fraction of the total research money was directed to studies of the utilization and improvement of metals. Even if the investigations in allied fields such as solid state physics are included, the total research expenditure for metal and mineral materials barely reached $500 million. An additional $200 million was spent by industry and government for development of minerals recovery and processing methods.

Jan 1, 1963

By Raymond B. Ladoo

The Bureau of Mines frequently receives requests for information on the mining , preparation and marketing of epsomite or Epsom salt , and in order to answer such inquiries the following information has been compiled . While it is probable that few people have considered epsonate as a mineral product , it will be noted that it should be so regarded and its production forms an important industry .

Mar 1, 1922

Reduce the costs associated with conventional treatment of acid mine water. Approach Conventional treatment of acid mine drainage consists of plants requiring large mixing and aeration tanks, mechanical aerators and large, shallow settling ponds. Such plants are usually very costly to construct, maintain and operate. The Bureau of Mines has developed a simple, low-maintenance, highly efficient system to treat acid mine drainage which mixes, aerates, and neutralizes mine water Simultaneously in the existing discharge pipeline by using the pressure generated by the deep mine discharge pumps. The mixing and aeration action of the in-line system significantly increases oxidation rates of ferrous iron. Iron and manganese are removed, even at near neutral pH levels, due to the high efficiency of this system. How It Works The In-line Aeration and Treatment System (ILS) consists of two commercially available components, a jet pump (ejector) and a static mixer. The jet pump is simply a nozzle that converts water, already under pressure, into a high-velocity stream that entrains air by Venturi action. If neutralization is required, sodium hydroxide or lime is added along with the air at the Venturi opening. The aerated and neutralized water then enters the static mixer, which is a length of internally spiralled pipe that mixes air and water together. The two components, which are both about 8 feet in length, replace the last section of discharge pipe at a point before the mine water is emptied into a pond. Along with the settling pond, these components treat the water so that it meets discharge criteria. The system has been used at surface drainage treatment facilities as well, but in such use a pump is required to provide the necessary pressure drop across the Venturi opening.

Jan 1, 1985

By John H. Soulé

"INTRODUCTION The Peerless mine was examined by W. R. Storms, an engineer of the Bureau of Mines, on June 2, 1944, in conjunction with a mineral survey of the adjoining For Bayard Military Reservation. Storms again studied the mine on January 13; 15 and 16, 1945, to determine the possibilities of finding new ore reserves to replace these depleted by mining. A project to explore the Peer-less vein at depths below and to the south of the principal mine workings was proposed. Special attention was given to the possibility of exploring favorable beds in the Magdalena and Lake Valley limestones at points near the Peerless fault.The proposed project was approve and exploratory work started on January 2, 1946, and was completed on June 5, 1946. The mine was not in operation during the project, and all equipment had been removed."

Apr 1, 1947

By A. B. Hooker, L. C. IlsLey

In lare-scal e blasting, it is customary to fire me.l'\Y shot.!:l simu1. taneously. The electric !atonators ara usually conneced in seies, ard are fired either from a power circuit or :from a blasting ma.chine with large capacity, operated by hand. "!hen :'::ri111; with a blasting ca.chine, trouble with missed shots has been freqi.,.ently e>:pert0nced.. Unit1:i:' thes ,:::rcu:ns tances, the shots that fail to fire are often a gr"up in the t.:E"nter r,f t>e series, Various explaz,.a.tions hs.ve been given as to the cause of the failurs. Tis paper covers a few tests made cy the electrical section of tl:.e Dti..'t'cau. cf Mines, wh;.r.;h may be helpful in understanding the -probable cuse of tl1e misfiring of c.:anter shots, Wh3tever th9 source ot the firir. current generator, magneto, or batter, the CUl"rent delivered th:·01.1.gh a shot-f:?·ing circu.it is determined by t.ae total resistance of ,;he clrcili +.; c:1nd all cure:it leaving th9 p,si tive terminal must return to tre negative te1-minal. If a. metallic circuit is well i1,.sul.:tted, praeti­ccl. l;1 a.ll of the t.'Urrent keepo within the circu.it; but in a. shot-!11·.irig ci.rc1li t, Nhere the ·.vires f:ll·e often 1n c.c,i.cact with the eru:"!ih as i11 wet holer., end whero the ins".lla.tion of the leg wires :i. inadecpa.te to prc·,ent lea.l.tage, the current ma.v tu.e v a.r ious pa the: thro-.. .. gh the nr r. earth.

Aug 1, 1922

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958