Search Documents

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By R. L. Zick, J. D. Byars, T. P. Mucho

Recently, a large Pittsburgh seam longwall mine was nearing depletion of a major portion of its current reserves and had begun to develop in a different direction from its original portal area to access additional reserves. This meant that a large area of the mine would be abandoned and sealed. However, continued use of the original mine portal area required that the water accumulating in the abandoned mine would eventually need to be pumped to the surface. This would be in addition to the discharge water associated with the new portion of the mine. Several pumping and sump options were investigated to handle the quantity and quality of the anticipated discharge water. This paper describes some of these options, their advantages and disadvantages, and the final engineering decisions. Some problems and unanticipated outcomes, as well as the eventual solutions are discussed, including: (1) estimates of pump requirements, (2) water pool size, (3) eventual water quality, (4) anticipated inflows, and (5) integration into the overall mine water system.

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966

By Edwin E. Maust

In response to the ever- increasing demand for high temperature materials, the Bureau of Mines instituted a program for the study and development of superrefractories, One of the major tools obtained for use in this research was an image furnace of the double-paraboloidal mirror type. Although extensive theoretical analyses of solar furnace performance may be found in the literature, comparable detailed information on the double-paraboloidal-mirror image furnace has been nonexistent. This report presents an analysis based on an investigation undertaken to ascertain the limitations and characteristics of the furnace so that it can be used most effectively. The quantitative determination of the energy available at the image, the control of this energy by mans of a 60-inch iris diaphragm, and its variation with position and time relative to the heat source used have all been dealt with in detail. The quantitative results were obtained using a specially designed waterflow calorimeter and these measurements, in conjunction with the theoretical analysis, are used to present a fairly complete description of the furnace and its capabilities.

Jan 1, 1962

By Edmund Newton

The Haile mine has been the outstanding gold-mining operation and the largest single producer of gold in the Appalachian region. Gold was discovered at the Haile in 1827, previous to the present operation, production has been nearly $4,500,000 (gold at $20.67 per ounce.) from somewhat over a million tons of ore, with an average extraction of about 70 percent. The Haile property, now operated by Haile Gold Mines, Inc., is in the southern part of Lancaster County, South Carolina, 3-1/2 miles northeast of the town of Kershaw and 55 miles north of Columbia, the State capital. (See fig. 1.) The corporation has a lease and purchase contract on 1,805 acres, covering the present productive area. In addition, it holds lease contracts on 1,500 acres additional adjacent to this area.

Jan 1, 1940

By D. Harrington

Although the explosion-fatality record for the fiscal year 1944 showed considerable improvement over those of the preceding 4 years, it is still fur from creditable, and the coal-mining industry and agencies interested in the prevention of coal-mine accidents should not be satisfied until accidents from explosions and fires are eliminated. In view of present knowledge of the methods of preventing explosions and fires, such disasters are inexcusable and discredit the mining industry. Despite this knowledge, far too many coal¬mine operators and employees continue to follow procedures that have resulted in disasters in the past. Included in the appendix to this circular are a number of safety measures designed to prevent coal-mine explosions and fires and metal-mine fires. Their adoption is essential if explosions and fires are to be prevented, as certainly they should be. An epidemic of disastrous mine fires of electrical origin during the past 2 years emphasizes the need for better methods of protection of underground electrical circuits. At present, committees of mining-electrical engineers, electrical-equipment manufacturers' representatives, and others are cooperating with the Bureau of Mines seeking means to solve this problem.

Jan 1, 1945

By Sean Gallagher

The vast majority of ergonomics research has addressed the demands of work in standing or sitting postures, and understandably so. However, many workers (for example, underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, and others) are often required to adopt postures such as kneeling, stooping, squatting, or lying down for significant periods of the work day.

Jan 1, 2005

By R. L. King

This report describes a method for designing and constructing ground beds that has been developed under the sponsorship of the Bureau of Mines. The procedures for designing and constructing a driven-rod ground bed with a resistance of 5 ohms or less are given. Some of the theory of soil resistivity and fall-of-potential resistance measurements is included. Results of a bed constructed at the Bureau of Mines mine car roadway are presented.

Jan 1, 1978

By Charles L. Harness

The barite industry has made notable progress since the days when barite was used only as an adulterant in white-lead paints and the only method of mining it was with pick and shovel. The following chronological record may serve to show how this heavy white mineral has grown in importance in the national exonomy and at the same time to indicate development of methods for obtaining it. 1845. - Barite first, mined in Fauquier County, Va., for use as an adulterant in white-lead paints. 1850 (approx.). - French settlers 60 miles southwest of St Louis, Mo., discovered barite; called it "'tiff;' meaning white. It was mined and shipped to St. Louis for use in paint.

Jan 1, 1946

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

By Bill York-Feirn

The Colorado Mine Safety & Training Program (MSTP), in late 2005, completed and began distributing two new training tools; one geared to underground coal mine foremen and the other to surface aggregate employees. Through strong partnerships with MSHA, Colorado Coal Mine Board of Examiners, Colorado Mining Association and the Colorado Rock Products Association, the MSTP continues to create innovative and interactive training tools for not only Colorado, but for the national mining community. "Although we shoot and produce these materials in Colorado, it's important to us to make sure they are useful nationally," said Bill York-Feirn, MS TP Manager. The interactive DVD program "Underground Mine Foreman Certification Study Guide (Coal)," was completed in October 2005. It won the 2005 Grand Prize at the MSHA National Training Materials Competition in Beaver, West Virginia. [ ] This program is fully based upon the requirements of Title 30 Code of Federal Regulations (30 CFR) Parts 48, 50, 70 and 75 for underground coal mine foremen. It contains eight modules plus immediate access to relevant laws in the appendix. Topics covered include: Federal Law, Practical Math Skills, Mine Gases, Ventilation Maps, and scenarios addressing a variety of practical mining concerns. The DVD is designed for self-¬paced study and practice.

Jan 1, 2006

By H. W. GILLETr, E. L. Mack

The production of small heats of alloy steels on an experimental scale is often desirable in beginning the study of new alloy steels before large amounts of expensive alloys are used in heats of commercial size. Such small heats can sometimes be made up at crucible-steel plants, but few crucible-steel makers care to undertake experimental heats for other firms. Small electric furnaces offer some advantages over crucible furnaces for experimental work. Hansen1 in 1909 described a small 100-kilowatt single-phase, direct- arc furnace with a capacity of 50 to 300 pounds of steel, and such furnaces, of 200 pounds capacity or larger, are being successfully used by various firms for experimental work. They have the advan- tage of using the same metallurgical procedure as is used in prac- tice for larger electric furnaces. The very small sizes have the draw- back of lack of precision in controlling the carbon content of the steel. Small Rennerfelt two-phase, indirect-arc furnaces of 40 to 60 kilo- watts and small Industrial Electric Furnace Co. furnaces, single- phase with one electrode embedded in the hearth, of 25 to 50 kilo- watts, are also in use by a few firms for experimental work or for production on a very small scale. Hoskins carbon-plate resistor crucible furnaces are also sometimes used. Little seems to have been published on the use of these furnaces in making experimental alloy steels. Keeney' has given data on the making of uranium steels in a tilting Siemens furnace of 25 pounds capacity, and has described a small stationary Siemens furnace.

Jan 1, 1922

By Craig C. Johnson

The purpose of this effort was to investigate the feasibility of employing a piezoelectric transducer for seismic communications applications in mine environments. The transducer, a government furnished device incorporated a high Q, spring-mass resonator to load the air side of the piezoelectric crystal. The resonant frequency was seismic load dependent and fell in the range of 300 to 340 Hz. The effort included a mathematical analysis of the transducer, with corroborative laboratory tests, together with actual communications experiments performed first in an open-formation limestone quarry and finally in an operating iron mine. This work showed that the transducer could be coupled efficiently to hard, competent rock media with power conversion efficiencies of 70 to 80 percent (electrical to mechanical) in typical installations. In the iron mine, when radiating peak power was about 30 W (acoustical) in a gated pulse mode, signals were received at a distance of 760 ft through a massive rhyolite porphyry formation. This represents a 15% radiation efficiency with an input of 200 watts. Despite the high ambient noise level due to operating mine machinery, a signal-to-noise ratio of about 20 dB was achieved using a very narrow band filter to process the received signal, and a data rate of about two pulses/sec was demonstrated.

Jan 1, 1972

This summary of State laws or explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful In determining whether relevant statutes exist, and In locating them quickly,-with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of those jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The ;purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of mining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENTS The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

By M. M. Gilkey

Pegmatites in Colorado occur for 150 miles along the Front Range (eastern-most range of the Rocky Mountains) from Larimer County on the north to Canon City on the south, and west into the Gunnison area. Many of the deposits have been classified. Minerals found in the various dikes include beryl, scrap and possibly punch mica, lithium-bearing minerals, columbite-tantalite, feldspar, and several rare minerals. Pegmatites are abundant in the Crystal Mountain district in Larimer County. About 5 miles south of the Crystal Mountain district and often identified with that district is the Hyatt pegmatite area. The Hyatt Ranch deposit has attracted particular attention because of the comparatively high beryl con-tent of the upper part exposed in opencut workings.

Jan 1, 1960

By R. S. Dean

The brief resume of the activities of the Metallurgical Division that appears annually in its progress reports series serves a useful purpose by making available a rather comprehensive but concise recapitulation of the current work, and publications of the division. An unprecedented opportunity to attack the problem of producing ferro-grade material from low-grade domestic manganese ores effectively was provided by the act designated as Public 667 of the 76th Congress of the United States, approved June 26, 1940, which made available an appropriation for "Expediting Production of Equipment and. Supplies for National Defense." Although the funds were not immediately available to the division, good progress has been made in the, solution of the many and diverse problems presented in the studies undertaken to determine the best methods for the recovery of useful products from a wide variety of manganese ores.

Jan 1, 1941

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966