Search Documents

By Thomas G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a chalcopyrite ore. The purpose was to obtain a direct comparison between moderate-temperature and elevated-temperature in situ leaching of copper trom minus la-inch ore and to analyze the sulfuric acid and oxygen requirements of the leaching system. Experiments employing oxygen were conducted at 35° and 90° C on 362-and 367-1b ore charges, respectively, under flooded conditions and at 400 psig. At 90° C, 47 pct of the copper was extracted in 913 days of leaching; at 35° C, 27 pct of the copper was extracted in 915 days. Diffusion into and out of the ore fragments con-trolled the rate of leaching. Oxygen consumption was 1.46 lb/lb of copper extracted at 35° C and 3.15 lb/lb of copper extracted at 90° C. Sulfuric acid requirements of the ore were 5.49 and 7.48 lb/lb of copper extracted at 35° and 90° C, respectively.

Jan 1, 1982

By Joseph E. Matta

The Bureau of Mines conducted tests using a tracer-gas technique to measure the effectiveness of the jet fan, which is often employed in mines to ventilate dead headings. Results of these tests show that jet fans can (1) ventilate dead headings beyond the maximum penetration distance indicated by smoke-tube detection of air movement, and (2) redistribute available fresh air through larger working areas. However, if the fresh air base is insufficient, the fan will merely recirculate the contaminated air and disperse it over a larger volume.

Jan 1, 1978

By Ted C. Briggs

A removable-jacket distortion apparatus was constructed and used to measure distortion coefficients for two high-pressure vessels. The measured distortion coefficients were used to compute distortion coefficients for volumes VI and (V1+V2) of a 1,000-atmosphere Burnett compressibility apparatus for the temperature range 0° to 75° C. Young?s modulus for Armco 17-4 PH stainless steel, heat treated to condition H1150-M, was computed from experimentally determined distortion coefficients. A 10-to 14-percent correction to the values obtained for Young's modulus may be required because pressure vessel end effects were neglected. The distortion coefficients of the compressibility apparatus are believed to be accurate to about 1 percent.

Jan 1, 1970

By G. W. Jones

Phthalic anhydride is a solid having the formula C8H4O3. It is an important intermediary in production of anthraquinene, alkyd reins, and plasticizers. The combined annual production of phthalic anhydride reported by 10 major manufacturers for 112,250 tons. The raw materials in the manufacture of phthalic anhydride have been the source of numerous fires and explosions. Consequently, the need was felt to determine the temperature flammability and the ignition temperatures crude basic raw material in most phthalic anhydride production crude phthalic anhydride, and pure phthalic anhydride.

Jan 1, 1950

By W. H. Engelmann

The electrokinetic (zeta) potentials of a charcoal granite in an aluminum chloride (AlCl3) solution and in an oleylanunonium acetate (C18H35NH3+ -OCOCH3) solution have been correlated with the specific damping values as measured by the pendulum sclerometer. This investigation shows that the pendulum specific damping attains a minimum at the isoelectric point for the charcoal granite-aluminum chloride and charcoal granite-oleylammonium acetate systems, and thus indicates that the penetration of the diamond points is a maximum at the isoelectric point.

Jan 1, 1967

By D. N. Nilsen

The Bureau of Mines is developing a method to recover Ni, Co, and Cu from laterites containing less than 1.2 pct Ni and 0.25 pct Co. The method consists of the following basic unit operations: (1) reduction roasting, (2) leaching, (3) solvent extraction, and (4) electrowinning. The method reflects three Bureau of Mines objectives: (1) recovery of critical minerals that are domestically in short supply from low-grade domestic laterites, (2) lower processing energy requirements, and (3) solution recycling. This report deals with the extraction of cobalt and the preparation of a suitable cobalt electrolyte by solvent extraction from liquor produced by this method. Nickel and copper are coextracted with LIX64N from an ammoniacal ammonium sulfate leach liquor containing about 1.00 g/l Ni, 0.30 g/l Co, 0.03 g/l Cu, and 0.02 g/l Zn. Cobalt (III) in the nickel-copper barren raffinate is reduced to cobalt (II) with cobalt metal. Reduction of cobalt (III) to cobalt (II) greatly aids subsequent extraction. Commercially available XI-51 extracts about 94 pct of the cobalt from the treated raffinate in one stage in a laboratory mixer-settler continuous circuit. Ammonia loaded on the solvent is removed in two washing steps. About 94 pct of the cobalt then is stripped from the XI-51 in one stage with spent cobalt electrolyte containing about 77 g/l Co and 18 g/l sulfuric acid (H2S04), Electrolytes containing less H2S04 also may be used. Preliminary data indicate that coextracted zinc may be removed from pregnant cobalt eletrolyte containing 3 g/l or less H2S04 with di-(2 ethylhexyl) phosphoric acid (D2EHPA).

Jan 1, 1980

"Correlatina Lung Crackle Usina Holographic lnterf erometryAli Afshari, MS, West Virginia University, 1989The Effect or Surfactants on Suppression of Non-Wettable ParticlesAli Alaboyun, MS, Mineral Engineering, The Pennsylvania State University, 1989Geochemical Characterization of Kerogem, ShaJes, and Coal .Refme ~ted with Allegheny Fonnationof Cases of Northern West VirginiaDick Andre, MS, West Virginia University, 1987Particle Concentrations in a Hazelton Inhalation ChamberShahram Bavani, MS, West Virginia University, 1985Use and Potential of Luer Holographic Interferometry and Subsidence Model Study of an Underground.Room and Pillar MineRichard Begley, MS, West Virginia University, 1984Development of a Mechanistic Model for Prediction of Subsidence in a Longwall MineRichard Begley, PhD, West Virginia University, 1990.Redesign of Micro-Orifice Unifonn Deposit ImpactorSteve Behm, MS, University of Minnesota, 1991A Fracture Mechanics Study of Crack Propagation Mechanism in Coal: The Mechanics of Fine FragmentFonnationZ. T. Bieniawski and R. Karl Zipf, Jr., Mining Engineering Department, The Pennsylvania State University,University Park, PA. Final Report, October 1, 1988A Mathematical Model for the Prediction of Ambient Dust Concentrations in Mine AtmospheresR. Bhaskar, MS, Mining Engineering and Operations Research, The Pennsylvania State University, 1984Spatial and Temporal Behavior of Dust in Mines-Theoretical and Experimental StudiesR. Bhaskar, PhD, Mining Engineering, The Pennsylvania State University, 1987Experimental Studies of Dispersion and Deposition of Fane Particles in a Wind Tunnel and Mine AirwayKlaus Bode, MS, Mining Engineering, The Pennsylvania State University, 1991Perf'onnance of the High Yield Technology PM - 100 - Particle 11ux MonitorRobert Caldow, MS, University of Minnesota, 1987Development of Improved Methods for Monitoring and Control of Diesel Particulate in an Underground CoalMineD. H. Carlson, B. C. Cornilsen, P. L. Loyselk, X. Shan and J. H. Johnson, Michigan Technological University,Houghton, Ml. Final Report, June 15, 1991"

Mar 1, 1992

By H. O. McDonald

Solutions containing Cr6+ and sulfuric acid are used in a number of surface-finishing operations. Substantial quantities of chromium and copper are lost and pollution problems are created when the spent solutions are discarded. To minimize the undesirable environmental effects while improving secondary resource recovery technology, the Bureau of Mines is conducting research to detoxify and recover metals from these solutions. Spent etchants are treated to remove copper and reduce Cr6+ to Cr 3+ in an electrolytic cell. The anodes and cathodes are granulated coke. The spent solution is continuously pumped through the electrodes. Hexavalent chromium is reduced to trivalent chromium, and copper is recovered at the cathode. Reoxidation of Cr3+ at the anode was not observed. The removal and recovery of copper reduction of Cr6+ lessen chemical demand and increase efficiency in waste in treatment operations associated with the use of these solutions.

Jan 1, 1980

By Fred N. Kissell

A parachute-type stopping intended for changing the course of mine ventilation air during mine emergencies has been designed and tested. Some production uses are also visualized for metal mines. Preliminary tests in the laboratory and underground indicate that the parachute stopping is a workable concept, but further developmental research is required.

Jan 1, 1975

By McHenry Mosier

The diamond-drill method was tried at the site selected for driving a 5- by 6 -foot air shaft at the east end of the Bellefonte mine . This method of sinking consisted , first , of drilling a 5-3/4 -inch-diameter cut hole from the surface , then drilling parallel 1.5 - inch ( EX ) holes around it at appropriate distances for a balanced blasting round . The cut hole was not charged with explosive but served as a relief chamber for the incipient expansion of the ground broken by. blasting the surrounding 1.5 - inch holes . The length of each hole was 236 feet , which was the finished depth of the shaft . The nature of the work in the air shaft was largely experimental , and many difficulties arising from the lack of special equipment and proper technique for precise alinement of the drill holes caused expensive delays before they could be overcome . Drilling the 5-3 /4 - inch hole , which was impeded by frequent core blocks in the core barrel , required 10 shifts . average advance per shift for an EX hole was about 150 feet . The The holes were charged and fired from the surface . The length of the section blasted in one cycle was 10 feet . Blasting progressed from the bottom of the shaft upward . The broken stone dropped into a chute , from which it was drawn into cars on the haulage level . The Bellefonte mine is an underground limestone mine.3/ The primary objective in undertaking the research on shaft sinking by diamond drilling was to perfect a method for driving connections between levels of the mine .

Oct 1, 1948

By D. Harrington

"There is continued activity in connection with probable reopening of old-time silver producers, but this is largely offset by other obstacles which make metal mining in Colorado a rather precarious proposition. Discussions at the joint meeting of the Colorado chapter of the American Mining Congress and the Colorado Metal Mining Association in Denver, January 20, 21, and 22, brought out many interesting facts, among them that Colorado, once a producer of high-grade ores, and with freight rates, smelting charges, etc. to accommodate high-grade ores, is now compelled to depend almost wholly upon low-grade complex ores or abandon mining, In the face of this, the railroads threaten to advance freight charges, and smelters , because of decreasing tonnage, high labor, etc., must either advance smelting charges or close (the Globe Smelter et Denver recently closed, and it is said that the Salida Smelter will close in February). A serious menace is the possibility of increase of rates by companies supplying electrical power, and the threat of the agricultural interests, now in the saddle in Colorado, to alter the laws so as to greatly increase the burden of taxation to be borne by the mines.In order to stimulate interest in Colorado metal mining, the Colorado Metal Mining Association and Colorado chapter of the American Mining Congress have planned to have an elaborately staged exhibit in the Denver Auditorium during the latter part of the coming summer, This exhibit will reproduce an old time mining camp,including mining structures such as mills, headframes, etc., as well as the camp saloons, dance and gambling halls, etc., together with mineral exhibits from many of the old time mines, no abandoned, but possibly to be reopened. due to increased price of silver, Inasmuch as the Bureau of Mines plans a National First-Aid meet at Denver in August or September, and the Rocky Mountain Mining Institute will also hold its summer meeting in Denver, it seems advisable to hold the three meetings simultaneously and it is proposed to have this done.Labor supply is fairly abundant and apparently not inclined to be dissatisfied; few, if any, strikes or other labor disturbances being found. In some mining regions advances in wages were posted January 1 and no wage reductions are noted.The Rocky Mountain Coal Mining Institute held its meeting at Denver, January 20, 21, and 22, and much attention was devoted to methods of bringing down coal without use of explosives chiefly by undercutting and subsequent use of hydraulic processes of forcing down the coal. Some attention was given the question of labor and it was suggested that the time is at hand when labor unions should be made responsible bodies by incorporation or otherwise. It was agreed to hold the summer meeting in Denver simul-taneously with the holding of the National First-Aid. and Mine Rescue Meet.In general, coal production in Colorado is proceeding satisfactorily with occasional interruption by local strikes, and tonnage is up to that being produced before the strike, but not nearly up to the record of 1918. In general, the labor supply is plentiful, but demand for coal is by no means great and unless some cold weather intervenes, it is probable that the lignite mines will have to go to a three or four day a week basis. There have been no recent disasters, but the Pictou mine of the Colorado Fuel and Iron Company encountered a heavy supply of water, and had to be abandoned until such time as arrangements can be made to pump or bale the water out."

Jan 1, 1920

By Charles A. Seitz

This Bureau of Mines report describes an automatic and continuous transducer-drift compensator. The compensator formed a part of the instrumentation used to indicate the saturation by hydrogen of a cryogenic, adsorption column. It has a variable delayed-response characteristic and will respond only to signals having rise times faster than component drift times. Zero drift due to varying ambient conditions and component aging is nullified. Equations relating the output as a function of the input signal are given.

Jan 1, 1981

By F. N. Kissell, R. J. Bielicki

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about 1 part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

By C. A. Alien

The increasing activity in oil shale has had a tendency to direct the attention of the industry to any substance from which gasoline or other oils can be secured . Cannel coal for many years has been known, as a source of oil and formerly it was the only substance from which kerosene was obtained . The name of coal oil was given to kerosene because it was derived from cannel coal before any flowing wells were brought in in the United States . In an isolated region in Southern Utah there is an unusually thick and clean bed of cannel coal which laboratory experiments indicate can be made to yield about seventy gallons of oil to the ton . This coal was first described in Bulletin 341 of the United States Geological Survey under the title of Colob coal field . This field lies at the western and southern base of the Colcb plateau and extends from the town of Cedar City southward to Kanarra and then southeastward to the town of Mount Carmel . Cedar City is 35 miles south of east from Lund on the Los Angeles and Salt Lake Railroad which is the nearest railroad point . Mount Carmel is about 90 miles south of Marysvale , on the Denver and Rio Grande Railroad , which is the nearest railroad point from the eastern end of the field . The Colob coal occurs in Lower Cretaceous rocks and a number of wagon mines have been opened on the seam in the vicinity of Cedar City , Kanarra , and Mt. Carmel , but between these places the field has been very little prospected . The cannel coal , so far as known at present , is limited to a small area on the head waters of the north fork of the Virgin River in Township 39 and 40 South , Range 9 East . In this region it occurs as a bed 5-1 /2 feet thick over which lies a layer of bituminous coal 2 feet and 5 inches thick .

Feb 1, 1921

By A. W. Khair, L. D. Gehl

"This paper describes the mechanism of coal and rock cutting from quasi-static indentation through dynamic indentation to rotary cutting. The results indicate that during quas~static indentation, a crushed zone, and subsurface fractures develop. The crushed zone is a potential source of dust generation. Dynamic indentation produces a crushed zone due to the frictional resistance offered by the coal or rock during penetration of the bit. Confining pressure changes the mode of failure from tension to mixed tension and shear. The wider bit causes larger crushed zone and more dust generation. The rotary cutting is a combination of quasi-static and dynamic indentation which results in chip formation. 1. INTRODUCTIONThe trend from conventional mining to continuous machine-cutting of coal, using more productive machinery is inexorable. Intolerable levels of dust generated at the face is an indication of inefficient coal or rock cutting by these machines. The Federal Government of the United States paid about 11.7 billion dollars workman compensation to more than 470,000 miners with Coal Workers Pneumoconiosis (Newmeyer, 1981). Bieniawski and Zipf (1985) reported that annual benefit payments were about 2 billion dollars. The need for research m improving coal cutting 1s therefore paramount. The enactment of Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanism and cutting tool design. The European countries were also engaged in the same area of research, however, their emphasis was in the use of wedge shaped bits. In 1981, the United States Bureau of Mines commissioned the South West Research Institute to investigate the effect of operating parameters mainly on airborne respirable dust in order to provide a healthier and safer atmosphere for coal mine workers.A research program by the Department of Mining Engineering, West Virginia University, USA was initiated to study the fragmentation mechanism during coal/ rock cutting. The research program was divided into three areas of research, namely quasi-static indentation, dynamic indentation and rotary cutting."

Dec 1, 1995

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of ventilation on the water spray patterns of automatic sprinkler heads. Experiments were performed in a rectangular tunnel with pendent, upright, pendent sidewall, and horizontal sidewall sprinkler heads at air velocities of 0, 150, 300, 500, and 800 ft/min. As the air velocities were increased, there were significant shifts in the total coverage areas, density distribution patterns, and the maximum coverage densities for all types of heads. The pendent and upright heads exhibited upstream shifts in total coverage in the direction of the air-flow ranging from 4 to 6 ft, while the downstream coverage distances were extended up to 14 ft at the 800 ft/min airflow. The shift in upstream coverage distance for the sidewall heads ranged from 6 to 12 ft, while the downstream coverage was extended up to 22 ft at 800 ft/min. The results showed that airflow can have a significant effect on the coverage characteristics of automatic sprinkler heads and needs to be considered in the design of effective sprinkler fire suppression systems for ventilated areas.

Jan 1, 2010

By Charles L. Kimbell

In overview, the world's mineral industry in 1989 registered gains over its 1988 performance, but these gains were by no means as pronounced as had been those of 1988. The traditional statistical measures of mineral industry performance, namely production, trade, and consumption levels, reflected significant growth in most industry sectors from crude material extraction through the gamut of down- stream processing. Growth in market economy countries generally exceeded growth in the centrally planned economy countries as a result of a variety of causes that will be covered subsequently, but even among the centrally planned countries there were some upturns. In contrast to these measures of the soundness of the industry, the situation for nonfuel mineral and metal prices was less satisfactory than in 1988, and low crude oil prices continued as a problem for the all-important petroleum sector, despite some gains during the year. The oil price situation mitigated against price increases for competitive fuels. Although this was unfavorable for fuel producers, it remained advantageous to consumers, including nonfuel mineral producers, processors, and transporters. Thus it cannot be viewed as a negative factor for the whole of the global mineral industry. Global crude mineral output value was estimated at nearly $1,420 billion in current dollars, an increase of 9% over the 1988 level, and an increase in current dollar terms for the seventh consecutive year. Measured in terms of constant dollars, however, adjusting for inflation, the increase was only 4.7% compared with the 1988 level. Despite the prolonged growth trend, the 1989 crude mineral output value level was still 3.2% below the record high set in 1980, which was $1,467 billion in terms of 1989 dollars.

Jan 1, 1992

By Timothy J. Rohrbacher

This report presents a U.S. Bureau of Mines study that incorporates coal mining factors, coal recovery factors, and economic factors into the definition of an economically recoverable coal resource. The relationship between these factors to the Energy Information Administration's estimate of U.S. coal resources-the "Demonstrated Reserve Base"-is discussed. The Matewan 7-1/2 minute quadrangle in eastern Kentucky was selected as the initial study area. Results indicate that of the original 1,193 million tons of resource in the quadrangle, only 89 million tons (7.5%) are economically recoverable at a cost of $25 per ton or less. At the current production rate of 5.3 million tons per year, this represents only 16.8 years of remaining reserves.

Jan 1, 1993

By W. L. Dare

The Federal Bureau of Mines is publishing a series of studies on the methods and costs of mining uranium on the Colorado Plateau. This report describes the longwall-mining methods and techniques used at the Radon mine, Big Indian district, San Juan County, Utah. The tabular Radon ore body lies on the southwest flank of the Lisbon Valley anticline, strikes N. 10° W., dips 7° SW., and has an average thickness of 4-1/2 to 5 ft. The mine is developed by a three-compartment vertical shaft, a haulage level driven beneath the ore, and a system of drifts driven within and parallel to the strike of the ore.

Jan 1, 1961

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40° F (-40°C) with 75% No. 1125% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34" C) with 75% No. 2/25% RO, and at 0° F(-18° C)with 50/50. Reference detonation velocity tests were conducted in 1.4" (3.6 cm) diameter steel pipe at 70°F (21°C) on No. 1 diesel ANFO (94-6), giving an average value of 9722 ft/s (2964 m/s). Comparison tests showed good ANFO performance at low temperatures. Blended fuel ANFO (75% No. 1/25% RO) mixed, loaded, and tested at -40°F (-40°C), produced an average velocity of 9247 Ws (281 8 m/s). A 50/50 blend gave a velocity of 8083 Ws (2464 ds) at -20°F (-29°C). Based on these results, a practical field method has been developed to help evaluate whether a specific oil blend will mix properly with AN at a low ambient temperature. This method will help to promote the safe and reliable use of RO ANFO at low temperatures, with adequate performance.

Jan 1, 2008