Search Documents

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.

By Tony Keller, Setsuo Maeda

Hand-Arm Vibration Syndrome (HAVS) was identified as early as 1918 in Bedford, Indiana in the U.S. Since then much research work has been done around the world in the areas of medical, epidemiological, engineering and legal aspects of HAVS. In Japan, much of the pioneering work in this field has been performed by Dr. Setsuo Maeda and his staff at the National Institute of Industrial Health (NIIH) in Kawasaki. Most recently, reports of work done by this group and by Dr. Ren Dong1 of NIOSH in the U.S., as well as many other suppliers and Japanese practitioners were presented at the 13th Japan Group Meeting on Human Response to Vibration held in Osaka2 during August 3-5, 2005. [ ]

Jan 6, 2006

By E. J. Gleim

To make a thorough survey of a coal mine in order to eliminate hazards, the competent safety engineer must be familiar with mere than one branch of engineering. It is essential that he know the properties of mine gases and the methods of detecting them, as well as hew to prevent dangerous as accumulations. It is also essential that he understand the action of overlying strata when the coal is removed, and the proper methods of protection by timbering or other suitable means of support. He must know the value of protective clothing in reducing injuries and mast be informed as to the correct handling and use of explosives to avoid premature blasts, misfires, and ether failures in blasting practice. He must understand hew to operate locomotives and cutting, loading, and various other types of machines to be able to recommend effective safeguards for protecting the men who use them in addition to being informed as 'to these and many ether activities connected with the mining of coal, he must net overlook electrical engineering if he wishes to combat the fire, shook, and ignition hazards attendant upon the use of electrical machinery and circuits in and around the mine intelligently. There are many points relating to safely in the selection, maintenance, and use of electrical circuits and equipment that are perfectly obvious to the electrical engineer but perhaps are not se evident to those not trained in this particular branch of engineering. Engineers of the U.S. Bureau of Mines who have made a special laboratory study of electricity as related to safety in minus haw e also made inspections of electrical installations at a large number of bituminous mines. These inspections have revealed practices and conditions that not only do not contribute to safety but that add nothing to efficiency and economy in the operation of the mine.

Jan 1, 1936

By K. O. Bennington

The thermodynamic properites of petalite (Li2A12Si8O20) were determined by the Bureau of Mines. The enthalpy of formation was determined by hydro-fluoric acid solution calorimetry. The values from the elements and from the oxides are ?Hf°298.15 = 2,335.8 ± 3.0 kcal/mole and ?H°295 (from oxides) = -50.60 ± 1.20 kcal/mole. Low-temperature heat capacities were determined by adiabatic calorimetry from 10.69 to 302.11 K. The derived standard entropy is S°298.15 = 111.0 ± 1 cal/deg-mole. Enthalpy increments above 298 K were measured by copper block calorimetry from 298 K to 1,193.6 K. The various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature from the elements and constituent oxides. The Gibbs energy of formation is ?G°f298.15 = 2,203.8 kcal/mole.

Jan 1, 1980

By R. H. Nafziger

As part of its program to help decrease the dependency of the United States on foreign imports of nonfuel minerals and to devise technology for the efficient and economic use of domestic resources, the Bureau of Mines smelted and sulfation-leached an ilmenite from northern Minnesota. The objective was to assess the feasibility of preparing chlorination-grade titanium feedstock. The concentrate was smelted with woodchips, coke, and soda ash in 91-kg-and 1-metric ton (mt)-capacity electric arc furnaces to form Ti-rich slag and commercial-grade pig iron. The slag contained from 67 to 77 wt pct titanium oxides and from 1.8 to 7.2 wt pct iron. Sulfation occurred in a 4.5-kg/h moving-bed reactor using S02-air mixtures at temperatures of 8000 to 8500 C to form soluble salts of the Ca, Mg, Mn,and Na impurities, which cause plugging of fluidized-bed chlorinators. Subsequently, the sulfated slag was leached in acid to remove the soluble sulfates. The final product from small-scale testing contained up to 95.5 wt pct Ti02, a minimum of 0.6 wt pct Fe, and a minimum total of 0.3 wt pct of the four impurities of interest. The final product meets charge specifications for chlorination. However, more large-scale testing is necessary.

Jan 1, 1987

By L. C. IlsLey, Charles M. Means

The descriptive rather than the strictly technical meaning of many of the terms and expressions used in the electrical rules is given in order to assist in their interpге- tation . ALIVE . At a potential measurable with a voltmeter and different from that of the earth or another conductor . (Static charges should be determined with an electrostatic voltmeter . This condition may apply to current - carrying parts , to noncurrent - carrying parts and adjacent material where a failure of insulation has taken place , and to objects having stored or static electricity . ) ALTERNATING CURRENT . A current that changes in direction -- positive or negative-- a certain number of times per second , depending upon the number of poles and speed of the generator . AMMETER. An instrument for measuring current , indicating in amperes . AMPERE . A term applied to denote the rate of current flow . ( Analogous to " gallons per minute " in a hydraulic system . ) APPROVED . Accepted as suitable by a competent committee , board , or organization designated by those adopting the rules . ductors . ARMOR . A steel or equivalent metallic covering for one or more electric con- AUTHORIZED PERSON . Anyone commissioned by the official in charge of the mine or his deputies to carry out certain duties incident to the generation , transformation , and distribution or use of electric energy in the mine , such person being one who is competent within the purpose of the rule in which the term is used .

May 1, 1930

By W. C. Hudson

"The Miami-West Palm Beach belt of silica sand, which may be suitable for the manufacture of high-grade glass, extends 65 miles northward from the neighborhood of Miami to the vicinity of West Palm Beach, The sand presumably originated in the host rocks constituting the oceanward slope of the Appalachian Mountains and the Piedmont Plateau of Georgia and the Carolinas. The sand now lies in a long, narrow, and probably thin belt that forms a dune-capped terrace marking a previous stage of submergence. The highest dune crests appear to be no more than 30 feet above sea level, and the water table is about 10 or 15 feet below the general level of the terrace.The width of the belt in several places is known to be more than a mile, and the thickness of the clean glass sand sampled ranged from 4 to more than 7 feet. Visual inspection and the meager data indicate the existence of bodies of glass sand large enough to supply foreseeable markets.Analyses of three samples indicate that beneficiation would make the sand suitable for the better grades of ordinary and flint glass.The prospective grade and quantity of sand, an available market in Florida for glassware, and the expectation of postwar expansion of the new industry of glass producing justify more detailed exploratory work and beneficiation testing.U. S. Route No. 1, Old Dixie Highway, the Seaboard Railway, and the Florida East Coast Railway, all substantially parallel and usually within a width of a mile or two, run along parts of the belt or between it and the coast. In addition to many streets and unpaved roads, a paved road crosses the belt at right angles about every 5 miles. Numerous towns are situated within or near the belt. Any area selected for a mining, processing, and manufacturing plant would be near a railroad, a highway, and water and also accessible to public utilities.The subtropical climate, famous for its pleasantly warm winters, would preclude seasonal interruption of plant operations."

Apr 1, 1946

By R. K. Clifford

Chalcopyrite (CuFeSz) concentrates produced on the Lead Belt of Missouri typically contain 28 pct Cu and from 0.5 to 1.5 pct each of nickel and cobalt. Most of the nickel and cobalt are present as the mineral siegenite, (Ni,Co)3S4, almost none of which is recovered presently. The Bureau of Mines, U.S. Department of the Interior, has been conducting research on the chalcopyrite to produce a marketable fraction enriched in cobalt and nickel. Ferric chloride leaching of various chalcopyrite (copper) concentrates has yielded residues containing from 10.2 to 16.2 pct Ni and 8.3 to 11.4 pct Co with recoveries of approximately 79 pct. In another approach, laboratory froth-flotation tests have been conducted to investigate the effects of regrinding, roasting, baking, and steaming prior to flotation, with a variety of reagents. The best laboratory results were obtained after regrinding the copper concentrate to 94 pct minus 400 mesh and floating the chalcopyrite at natural pH (6.5) with 0.48 pound of sodium diethyldithiophosphate and 0.01 pound of sodium cyanide per ton of concentrate. This procedure yielded a tailings assaying 20.4 pct Cu, 5.2 pct Ni, and 3.45 pct Co. The tailings contained 67.2 pct of the nickel and cobalt and 15.9 pct of the copper originally in the copper concentrate; the remainder of the values reported to the flotation concentrate, which analyzed 29.6 pct Cu. To verify the laboratory flotation results, a 60 kg/hr process demonstration unit (PDU) was constructed in the Cominco American Magmont mill, Bixby, Mo.

Jan 1, 1978

By W. A. Haley

The purpose of this investigation was to develop and improve mining methods for mining thin coal beds, to increase productivity, and to increase the recovery of coal. German coal planers and a modified longwall system of mining were introduced into American mines and are bringing about increased productivity and better recovery as compared with the conventional methods displaced. Since the first installation, 4 additional planers have been purchased by coal companies and over 1-1/2 mil¬lion tons of coal has been mined by them, using the modified longwall mining method. INTRODUCTION Except from 1932 to 1934, the growth of mechanical loading in underground bituminous-coal and lignite mines in the United States has increased steadily. The amount of coal loaded mechanically in underground mines has increased from 0.3 percent in 1923 to 79.6 percent of the total underground production in 1953.3/ The use of new and improved mining machines and auxiliary equipment, together with new techniques in mining methods, usually has resulted in increased productivity.

Jan 1, 1957

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry, and seal manufacturers recently conducted a series of full-scale experiments within the underground experimental mine at PRL’s Lake Lynn Laboratory. The purpose of the experiments was toe valuate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in 6 to 10 hr and are capable of with standing explosion overpressures in excess of 140 kPa (20 psi). These novel seal designs use available mine materials, do not require conventional rib hitching, and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least- radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By D. S. Colby

The productive capacity of natural gasoline and cycling plants in the United States or. January 1, 1954, was 926 thousand barrels per day, according to the Bureau of Mines biennial survey. This represented an increase of 114 thousand barrels per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 164 thousand barrels per day. The total number of plants increased from 521 on January 1, 1952, to 535 on January 1, 1954. The number of operating plants increased from 506 to 521. The major increases in capacity took place in Texas, Illinois, Oklahoma, Louisiana, and New Mexico, with the absorption-type plant continuing to account for most of the new construction. In 1954, however, 6 plants reported using a refrigeration process whereas only 1 plant reported this in 1952. The number of operating compression-type plants continued to decline and combination plants showed a decline this year because a number of these plants were reclassified as absorption-type.

Jan 1, 1954

By F. W. Richard

This paper describing the mining practices at the Ground Hog Unit of the Asarco Mining Co., a subsidiary of the American Smelting and Refining Co., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts of the United Stated. The Ground Hog mine is at Vanadium in the Central mining district, Grant County, N. Mex., about 1.0 miles east of Silver City and 2 ½ miles southwest of Santa Rita. A branch line of the Atchison, Topeka & Santa Fe Railway connects Vanadium with Deming, about 45 miles southeast.

Jan 1, 1930

By J. H. Russell

A mathematical modeling method was developed by the U.S. Bureau of Mines for the prediction of the principal equilibrium species in the solvent extraction of nickel. Models were developed for the extraction of nickel from ammoniacal sulfate and carbonate solutions with commercial oxime extractants. Independent variables in the research were nickel concentration, ionic strength, pH of the initial aqueous phase, and extract ants and their concentrations in the organic phase. Results from laboratory shakeout tests compared fairly well with predictions of the equilibrium concentrations of nickel and pH values. For example, the loading of nickel onto the extractant was predicted on average within ±27 pct of the measured values, and the pH to within ± 0.17 pH unit.

Jan 1, 1991

By E. W. Dean

In the early winter of 1919 the Pittsburgh petroleum laboratory of the Bureau of Mines undertook the work of testing fuel oil samples representing purchases of the United State Shipping Board for ships sailing from the port of New York. fuel oil was, at this time, being bought on a contract which involved specifications issued by the United States Navy under dace of October 2, 1920 (See Bulletin 1, Oil Division, U. S. Fuel Administration.)The object of the Bureau of Mines in undertaking this inspection work was twofold. (1) The Bureau was in position to give, and the Shipping Board needed, reliable laboratory service for checking the quality of the fuel oil purchased, the value of which ran into millions of dollars for,year's supply. (2) It was believed, and later demonstrated, that the existing specifications did not insure the obtaining of a reliably satisfactory quality of oil.The objection to the specifications concerned the employment of a clause limiting the gravity of the oil. The inadequacy of gravity specifications for several types of petroleum products has long been recognized, and there was every reason to reason to believe that they were no more desirable for fuel oil than for gasoline, kerosene, or lubricating oil. A first and obvious objection was the fact that it is somewhat difficult to make accurate gravity tests on ""heavy"" residuum fuel oils. (The Bureau found it necessary to employ or such tests a rather tedious procedure involving the use of a picnometer and an accurate balance, as the simpler methods, employing hydrometer or displacement balance, proved unreliable in a large proportion of cases.) A second and more important objection was that gravity tests, even when accurately made, do not provide a reliable index of the actual quality of the oil.

Feb 1, 1921

By Edward L. McHugh, Jami M. Girard

While less than 1% of reported accidents are associated with slope stability problems, slope failures were responsible for about 15% of all U.S. surface mine fatalities between 1995 and 2001. Small rockfalls, which may involve hand-sized rocks weighing only a few kilograms, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic meters of material or more can be fatal even for heavy equipment operators. As part of an ongoing study at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, several remote-sensing technologies are being evaluated as tools to monitor slopes for hazards and to assess slope stability. Field tests of a hyper spectral imager were conducted to assess its value for improving geologic maps of potentially unstable alteration zones on mine slopes. An interferometric radar device capable of detecting very small displacements on slopes awaits final assembly and field testing. Computerized monitoring methods using images from digital and video cameras are being assessed for application to mine slope surveillance. These and other techniques will eventually provide new tools to augment current methods for monitoring ground control hazards in mines.

By Fred D. Wright

A drill unit designed by Bureau of Mines engineers for testing various types of rotary bits has been in use since April 1950 at the experimental oil-shale mine near Rifle, Colo. The unit has a hydraulic drill and feed system, which provides the wide range of operating conditions necessary for adequate testing of drill bits and for obtaining data needed for the design of production scale equipment. Through the use of this unit, it has been proved that rotary drilling of vertical holes for mining the benches of the oil-shale mine is much cheaper than percussion drilling, and it is believed that in the near future the rotary drilling of horizontal blast holes in the top heading of the mine will prove equally economical.

Jan 1, 1952

By J. A. Herdlick

"INTRODUCTION The Bureau of Mines began a broad program of exploration of various proportion in the Pine Creek area of the Coeur d'Alene mining region in the fall of 1943. As a part of this project, exploring was done at theLittle Pittsburg property in 1945. The work included driving a 500-foot crosscut from the No, 6 level and drilling four diamond core drill holes to test the behavior of the Little Pittsburg vein at depth. This report presents the data obtained by the Bureau.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyses samples and performs beneficiation tests.The Bureau's exploration of the Little Pittsburg vein was one of the activities of the Albany Division of the Mining Branch, S. H. Lorain, chief. The project was started by R. M. Gammell, mining engineer, and was continued by the author and J. R. Reynolds, assistant mining engineer.The chemical analyses included in this report were made at Reno, Nov., under the direction of A.C, Rice, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines.The cooperation and assistance of the management of the Denver Development Co. is gratefully acknowledged, in particular that of C. E. Nugent, who made available much of the operational data included in this report."

Jan 1, 1947

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station of the Bureau of Mines have shown that satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but also upon the kind

Jan 1, 1945