Search Documents

By A. R. Taylor

Low-temperature heat capacities of cesium chloride (7° - 300° K) and cesium iodide (13° - 300°K) were measured with an adiabatic calorimeter. The heat-capacity measurements were analyzed graphically to determine smooth values of heat capacity, entropy, enthalpy function, and free-energy function at 10° K intervals and at 273.15° and 298.15° K.

Jan 1, 1963

By R. Karl Zipf

In some instances, extensive room-and-pillar working scan collapse with little warning and pose a serious risk to underground miners. Traditional strength-based pillar design methods applicable to coal or hard-rock mines use a factor of safety defined as pillar strength divided by pillar stress. Factor of stability, defined as local mine stiffness divided by post-failure pillar stiffness, may offer a way to design room-and-pillar mines and eliminate collapses. Three alternative design approaches to decreasing the risk of large-scale catastrophic collapses are described: the containment approach, the prevention approach, and the full-extraction approach. Until good data on the post-failure behavior of pillars become available, the containment and full-extraction options are the safest. The limitations in our ability to evaluate both the stability of old workings and the long-term performance of room-and-pillar mines are described.

A Helix Pressure Gauge to Indicate roof bolt loads was designed, fabricated and field tested. The gauge indicated loads between 3,000 and 15,000 pounds with a ± ten per cent error. The coat of fabrication of the gauge was estimated to be $3.39 including an assumed overhead and profit per indicator for a series production of 5,000 unite. The unit can be read on a bolt to within ± 1,000 pounds load from a distance of twenty feet.

Jan 1, 1974

By A. D. Hahn

This report describes reconnaissance by the Bureau of Mines of titanium-bearing beach sands on Ship Island in the Gulf of Mexico off the south coast of Harrison County, Miss. The purpose was to determine the ilmenite, rutile, and associated heavy-mineral content of black-sand-bearing beach sands. The investigation was part of a survey of titanium resources of the United States. Ilmenite (FeTi03), an iron-titanium oxide, is the major titanium-bearing mineral consumed in the titanium pigment industry. Rutile (TiO2), titanium dioxide, is used mainly as a constituent in welding-rod coatings and in producing titanium metal. The major fieldwork was conducted during the first half of February 1961. Nine holes, totaling 220 feet of bore, from which 110 samples Her taken, were drilled at widely spaced intervals on the island.

Jan 1, 1962

By John Nagy, Henry G. Dorsett, Murray Jacobson

Laboratory studies show that ignition of a dispersed combustible dust in an open vessel may be prevented by adequate inerting . Factors affecting the inerting requirements are -- dust concentration , spark energy , ignition temperature , composition of the substances used for inerting , fineness of dust and type of combustible . The oxygen concentration of the atmosphere and in some instances the proportion of admixed inert powder and moisture required to prevent ignition are given for 367 dust samples . Variations in inerting requirements with strength of igniting source are discussed .

Jan 1, 1964

Maps To Accompany Bulletin 507

Jan 1, 1952

By V. C. Petersen

The titanium-rich end of the titanium-germanium system was investigated by x-ray and metallographic methods and verified by resistivity and dilatometer measurements. A constitution diagram is proposed. The titanium-rich portion of the phase diagram is characterized by eutectic and peritectic reactions. The eutectic composition is 19 percent germanium, and the eutectic temperature 1,360° C. The peritectic reaction occurs at 905° C. and 4 percent germanium. Germanium is soluble in alpha titanium to a maximum of 4 percent at 905° C. and in beta titanium to a maximum of 12.5 percent at 1,360° C. Both limits of solubility decrease with decreasing temperatures. Although substantial quantities of germanium are soluble in beta titanium, beta is not retained on quenching. The beta phase probably transforms to alpha by a martensitic reaction.

Jan 1, 1957

By J. R. Ruark

This report presents results of the research and development work and operations performed during stage II of the gas combustion retorting research program conducted by the Colorado School of Mines Research Foundation and six major oil companies at the Bureau of Mines Anvil Points Research Facilities. The experimental program, including retort modification and air-gas distributor development, effects of shale quality and particle-size distribution, and other variables on the process, is discussed. Although operating problems are not fully resolved, it appears that the gas combustion retorting process can be successfully applied to achieve oil yields in excess of 85 percent of Fischer assay at mass shale feed rates of 500 pounds per hour per square foot of cross-sectional bed area, approximately twice the rate previously demonstrated to be reasonably practicable.

Jan 1, 1971

By F. R. McDonald

The compound ?-valerolactone has been identified in an acid fraction isolated from waste water collected from an in situ oil-shale retort. Infrared, nuclear magnetic resonance, and mass spectrometry were used by the Bureau of Mines to confirm the identification of a subfraction collected from a gas chromatograph.

Jan 1, 1974

By F. E. Armstrong

Tritiated water has been used as a tracer to follow the path of leach liquids as they flow through a copper-mine dump. Semipermeable layers, produced within the dump by compaction and "stratification" of deposized dump material, restrict the vertical movement of water. Knowledge of this restriction would aid in the optimization of the leaching process. The portion of the dump of particular interest was approximately 2,000 feet long, 800 feet wide, and 200 feet high. A total of 94 curies of tritiated water was injected into the dump at the rate of 650 gpm over a period of 39 hours. The leach liquid was sampled at natural surface outflows and through a series of wells, some drilled to the bottom of the dump and others to intermediate levels. More than 3,300 samples were analyzed, most by liquid scintillation counting, but a few hundred by gas counting. Data obtained permitted calculation of flow paths, recycle times, total fluid volume, and estimates of retention times in various portions of the dump.

Jan 1, 1971

By Paul Biggs

This Bureau of Mines report provides information on 138 waterflood projects in Wyoming. Injection was in 25 producing zones and 65 fields. Specific data presented include field location, discovery and development, water supply and injection, oil and water production, estimates of oil in place, and oil recoveries by primary and secondary methods. The 138 projects studied will, if successful, recover about 800 million barrels of secondary oil. Almost all of the injection water is from deep water wells.

Jan 1, 1970

By Louis C. Brichta

The Rush Creek district of Marion County, Ark., has had a more or less continuous record of zinc production over the past 40 years. The ore has come from many small mines working on oxidized and semi-oxidized deposits found in the Everton formation where that formation forms the present surface rock. Prospecting has been restricted to the hillsides above the creek levels, the actual ore outcrops being the guides. Little attention has been paid the possible sulfide zones. In August 1942, the United States Geological Survey and the Bureau of Mines recommended exploration of the Powell and Cotter formations, which underlie the Everton, for which purpose the Survey had previously located 18 proposed drill-hole sites in geological structures that seemed favorable to are deposition.

Jan 1, 1949

By Andrew D. O. O’Brien, Linda J. McWilliams, Joe L. Howell, Douglas E. Pollock, Jeanne A. Zimmer, Andrew B. Cecala

A quick, safe, and effective method has been developed that allows workers to clean their dust laden work clothing periodically throughout the day. For the mining industry, this technique is much more effective than the current federally approved method of using a vacuuming system. This newly designed method is relatively inexpensive and can be easily installed at any operation to allow workers to clean their clothing without contaminating the worker, the work environment. or co-workers to elevated respirable dust levels. This clothes cleaning process uses an air spray manifold to blow dust from a worker's clothing in an enclosed booth, which combines the dust for capture and removal by a baghouse dust collector. Since the air exhausted by the dust collector causes the booth to be under negative pressure. no measurable quantities of dust were ever measure escaping from the booth to contaminate the work environment and/or other workers. The worker performing the cleaning process is required to wear a half-mask fit- tested respirator with an N 100 filter, hearing protection, and full seal goggles. Dust samples taken inside the respirator of test personnel performing the clothes cleaning process showed very minimal to no respirable dust. This clothes cleaning process was performed in less than 20 seconds and was significantly y cleaner than either the Federally approved method of vacuuming, or the most common method or using a single compressed air hose. It was also determined during this research that polyester-cotton blend coveralls clean more effectively than coveralls which are 100 percent cotton. The newly designed clothes cleaning process has potential application to any industry where workers' clothing becomes contaminated with most any type of dust or product.

1. In 2003, 14,391 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (49%) were sand and gravel mines, followed by stone mines (30%), coal mines (14%), nonmetal mines (5%), and metal mines (2%).

Feb 1, 2005

By Van E. Shaw

Bastnaesite is a natural rare-earth fluorcarbonate of the cerium group that affords an abundant and high-grade source of the lighter rare-earth elements. A simple and efficient method has been developed by the Bureau of Mines for extracting rare-earth compounds from this mineral. Digesting of a flotation concentrate with sulfuric acid converts the rare-earth compounds from fluorcarbonates to sulfates. Action of the acid releases gaseous com-pounds of fluorine and silicon, leaving the sulfated material free of these elements; carbon dioxide from carbonate decomposition is eliminated at the same time. Calcining the sulfated material at 1,200° F. renders the gangue constituents insoluble, whereas the rare-earth sulfates are left in water-soluble form. Leaching with water yields a solution of pure rare-earth sulfates. Bastnaesite could become prominent as a source of cerium-group rare-earth elements. It is rich in the light rare-earth elements and comparatively easy to process; reserves of the mineral are extensive enough to supply a greatly expanded market for many years.

Jan 1, 1959

1. In 2003, a total of 1,972 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 13.7% of all mining operations. • Bituminous mines comprised 92.5% (n = 1,825) and anthracite mines 7.5% (n = 147) of coal mining operations. • More than 70% of all coal mines were located in three states: Kentucky (29.0%), West Virginia (20.9%), and Pennsylvania (20.2%). • Bituminous coal mines reported the production of over 1 billion coal tons.

Feb 1, 2005

By B. W. Jong

The U.S. Bureau of Mines investigated anhydrous chlorination and caustic-acid leaching processes to recover Ni, Co, Mo, and W from waste hydroprocessing catalysts. In batch laboratory-scale equipment, the chlorination process extracted 61 to 99 pet of the metals. Final recovery was 65 to 99 pct. The caustic-acid leaching process extracted 81 to 98 pct of the metals. Final recovery was 36 to 99 pct. Chlorination processing included roasting, chlorination, hydrolysis of metal chlorides for recovering Mo or W, water leaching of Ni or Co from the spent charge, purification, and solvent extraction or precipitation of Ni or Co from the purified solutions. Caustic-acid leach processing included NaOH leaching, solvent extraction of Mo or W from the NaOH leach liquor, H2S04 leaching of the NaOH leach residue, purification, and solvent extraction or precipitation of Ni or Co from the purified solution. The estimated fixed capital cost for a commercial-scale plant processing 39,000 Ibid of waste Ni-Mo-AI catalyst was $8 million for the chlorination process and $9.6 million for the caustic-acid leaching process. The estimated operating cost was about $0.20 and $0.40 per pound of the waste catalyst, respectively, for the two processes.

Jan 1, 1989

By H. R. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

By S. A. Gustavson, H. E. Olund

This report has been prepared to review the history of the Premium Price Plan for copper, lead, and zinc, which was in operation from February 1, 1942, to June 30, 1947. It includes various charts and tables comparing costs and production data, and data on exploration premiums that were included in the Plan during the last year of its operation.

Jan 1, 1950

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

1, Introduction This report is submitted in fulfillment of the requirements of USBM Contract No. J0255017, "Development of Emergency Escape Systems Guidelines for Underground Metal and Nonmetal Mines" Under this contract the history of past mine fires was studied. Representative metal and nonmetal mines were surveyed and escapeways, refuge chambers, life support, and emergency hoist requirements were studied to determine the problems in complying with the proposed regulatory standards and their enforcement by MESA Mine Inspectors. In addition, a computer program was written to evaluate mine evacuation performance. The completed program is included in the appendix. 1. 1 Historical Review of Metal and Nonmetal Mine Fires Early records of mine fires are poorly documented because there was no statutory provision for reporting fires to the Bureau of Mines. The survey of representative mines during the course of this contract indicated that many small fires still go unreported even though they are now required to report all fires A recent report survey approximately 80 disasters in metal and nonmetal mines, (6 ) Table I is a summary of some of these fires. Historically most metal and nonmetal mine fires have been caused by electrical problems. Spontaneous combustion and the use of welding equipment are the other major causes of mine fires(14) Although not documented, many mine personnel agree that 30 percent to 40 percent of underground metal and nonmetal mine fires have their origin from cigarettes and other smoking related materials. The number of fires related to spontaneous combustion is decreasing and equipment fires are on the increase. The reduction of spontaneous combustion fires can be attributed to the use of sandfill in more mines and the increase in equipment fires to the increased use of LHD equipment.

Jan 1, 1976