Search Documents

By David Burgess

Natural gas is a general term applied to the gas obtained from oil or gas wells. It is the most widely used of all gaseous fuels. The principal disadvantage in the use of this and other gaseous fuels is the difficulty encountered in the storage and transportation of large quantities in the gas state. Handling in the liquid state is possible, but reduced temperatures are required since methane (table 1) is the principal component of most natural gases that are used as fuels. Actually, liquid storage has been utilized both here and abroad;3 however, the Cleveland disaster4 has pointed out the need for a critical evaluation of the hazards involved in the storage of this cryogenic fuel. Accordingly, a program was undertaken to obtain basic data that could be used to assess these hazards. In this report, the factors to be considered in an evaluation of the fire and explosion hazards associated with any fuel are each discussed briefly. These factors are then used to assist in the design of experiments for the evaluation of the hazards associated with liquefied natural gas (LNG) relative to those associated with other common fuels. Experiments have been conducted on the vaporization of LNG, the mixing of LNG vapors with air, the effect of temperature and nitrogen dilution on the limits of flammability of methane in air, the burning rates of LNG and other fuels, flame radiation, and extinguishment of fires above liquid pools. Based on the results of these experiments, LNG can be stored safely in suitably designed above-ground tanks surrounded by earthen dikes in much the same manner as gasoline.

Jan 1, 1962

By Frank G. Schwartz

VARIABLES OF composition and environment affecting storage stability of gasoline-type fuels were studied, utilizing radioactive tracers and other analytical techniques. Changes in gasoline composition brought about by aging were determined and correlated with gum formation. The amounts of reaction of selected gasoline components, measured by radioactive tracers, were determined in a gasoline-type blend and in a mixture of 17 selected pure gasoline components. The data show that sulfur compounds, nitrogen compounds, polycyclics, and olefins enter into gum-forming reactions. Certain sulfur and nitrogen compounds were found to be most reactive in the gum-forming process. Results of this study indicate that the aromatic constituents of gasolines may contribute substantially and directly to gum formation. A mixture of tetralin and indan-type compounds is reactive, and this mixture appears to be the main aromatic portion entering into gum formation. A secondary but significant amount of naphthalenes also appears to have reacted in the gum-forming process. Analyses of the sulfm compounds in a fresh and an aged fuel indicated that elemental sulfur, hydrogen sulfide, thiols, sulfides, and disulfides were depleted during aging, but thiophenes and residual sulfur compounds were not depleted by fuel deterioration.

Jan 1, 1964

By Michael J. Brnich

During the past 15 years the number of reportable mine fires has declined. A decline in the number of reportable fires is a gross indicator that allows experts to say something about the underground coal industry generally: There has been some improvement in overall mine fire preparedness. However, such an indicator is less reliable as a predictor of readiness at any particular operation. An indication of fire fighting preparedness would have to be assessed from evidence gathered at the mine site. In other words, there are two levels from which to view the problem. On a general level, there has been significant improvement in the industry's fire response capabilities over the past two decades. Specifically, however, little data has been gathered on a site-by-site basis to determine what improvements might be made on a local level. These improvements would move beyond regulatory compliance. It is expected that this manuscript, based on work conducted at an underground coal mine in the western United States, will help to focus attention on some central concerns involving this critical issue.

Jan 1, 2006

By H. D. Hess

This report describes in detail a unique occurrence of fersmite, (Ca, Ce, Na) (Cb, Ti, Fe, Al)2 (0, OH, F)6, which occurs as small anhedral inclusions and intergrowths with a tantalum-free columbite found in the metamorphic complexes of Ravalli County, Mont. Chemical and crystallographic data along with the physical and optical properties agree in general with those given in the original description of fersmite from the Ural Mountains of Russia. X-ray diffraction data not given in the original description and more specific optical data have been determined. The Montana fersmite, now established as the second occurrence of this rare calcium-columbate mineral, was discovered during a routine Bureau of Mines mineralogical examination of a prospector's sample.

Jan 1, 1960

By Frederick Bloetscher

An improved parachute-type stopping for changing the course of mine ventilation air during mine emergencies has been developed by Goodyear Aerospace Corporation for The Bureau of Mines. The stopping can be quickly deployed by one man from a single attachment point and provides excellent stopping performance with the flow in the design direction. Adding pin and foam attachments between its skirt and the passage-way surfaces improves its performance with flow in the design direction and maintains the stopping with zero or reverse air flows. Stopping performance results for a range of airway sizes including 7.5 X 10 ft simulated airway with pressure differentials of up to 3.0 inches of water are presented. Predicted performance values for this stopping design for larger passageways are also presented.

Jan 1, 1977

By James A. Wasson

This report analyzes the petroleum-production potential of the basal Greenbrier dolomite zone, Sycamore-Millstone field, Sherman District, Calhoun County, W. Va., through the application of certain secondary-recovery methods. The well logs obtained and the core recovered from a well in this formation permitted an evaluation of the productive capability of the reservoir, Approximately 120,000 stb of oil may be produced from a 20-acre five-spot unit at breakthrough if the property is waterflooded. At an assumed limiting producing gas-oil ratio of 20)000 sef/stb, approximately 69,000 stb of oil should be recovered by low-pressure gas drive.

Jan 1, 1967

By Cavallaro. J. A.

This report presents the results of a washability study of 455 raw coal channel samples with special emphasis on sulfur reduction. These raw coals contained on the average 14.0 percent ash, 1.91 percent pyritic sulfur, and 3.02 percent total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds. Finally a similar statistical evaluation is included showing composited data interpolated at Btu recovery levels of 50, 60, 70, 80, 90, and 100 percent. Graphical summations are presented for the various coal producing regions. Generally, significant sulfur reduction is achieved if the coals are crushed to a finer size and the higher specific gravity increments are removed. If a 50-percent Btu recovery was acceptable, then 32 percent of the samples tested could be upgraded to meet the current Environmental Protection Agency (EPA) standard of 1.2 pounds of S02 emission per million (MM) Btu when crushed to 14-mesh top size and separated gravimetrically.

Jan 1, 1976

By C. E. Reistle

The generation of steam for drilling operations has visually been accomplished in the past by the use of portable locomotive-type boilers without the aid of auxiliary equipment or advanced for economizing fuel or water consumption. This has been due primarily to the fact that the steam-generating plant of a drilling well must necessarily be of temporary and portable design, and the amount of steam generated has not been considered sufficient to justify the additional expense necessary to obtain more economical operation. However, with the constantly increasing depth to which oil wells are being drilled and the use of larger and heavier equipment, the steam requirements have reached a point where equipment and methods that were previously considered as applicable only to permanent plant installation can be and are being used to a decided advantage by the more progressive operators. As an example of the present-day requirements and the rapidly increasing steam consumption in rotary drilling, a comparison between the requirements during the intensive drilling period in the Seminole end Oklahoma City fields of Oklahoma is of interest. In the Seminole field. There the approximate depth of rotary drilling was 3,500 feet, the general practice was to use three 85 to 90 or 100 horsepower A. P. I. code boilers operating at a working pressure of 175 to 200 pounds per square inch. The fuel end water consumption was approximately 450 to 500 thousand cubic feet of gas and 700 to 750 barrels of water per day. In the Oklahoma City field, where the average drilling depth is approximately 6,500 feet, the general practice is to use either four 100 or 116 horsepower or three 123 horsepower A.P.I. code boilers, operating at a pressure of 250 pounds per square inch. The fuel and water consumption varies from 550 to 750 thousand cubic feet of gas and from 1,000 to 1,500 barrels of water per day.

Jan 1, 1930

By N. S. Dalal, Xiaoya Sun, Xianglin Shi

"The in vivo toxicity of vanadium(V) has been found to correlate with the depletion of cellular glutathione and related non-protein thiols. With a view to understanding the mechanism for this observation, we have investigated the oxidation of glutathione, cysteine N·acetylcystcinc and pcnicil· lamine by vanadium(V), using electron spin resonance (ESR) and ESR spin trapping methodology. The spin trap used was 5,5-dimethyl-l-pyrroline I-oxide (DMPO). It is found that the oxidation of these thiols by vanadium(V) generates the corresponding thiyl radicals and vanadilim- (IV) complexes. The results suggest that free radical reactions play a significant role in the depletion of cellular thiols by vanadium(V) and hence in vanadium(V) toxicity. 1. INTRODUCTIONThis communication reports on the identification of thiyl radicals formed as intermediates in the reaction of vanadium(V) with glutathione (GSH) and related nonprotein thiols. This study was undertaken because the biochemical mechanism of vanadium toxicity is still not fully understood,. despite being a topic of current research activity [1-20). As to possible clues, it is known that vanadium is most toxic when administered in its pentavaient state [21), and that vanadium(V) administration into laboratory mice reduces cellular levels of NAD(P)H and GSH [22). While the oxidation of NAD(P)H by vanadium has been studied extensively [16-20), that of glutathione and related non-protein thiols has been paid less attention. On the other hand, GSH and related thiols are important cellular antioxidants [23). Their functions include decomposing lipid peroxides and protecting cell membranes [23-25). Thus any reduction in the cellular contents of such nonprotein thiols after vanadium exposure may result in the accumulation of lipid peroxides which might ultimately lead to tissue injury. With a view of finding the mechanism for this thiol depletion process, we have investigated reactions of non-protein thiols with vanadium(V). Particular attention has been paid to the detection of thiyl radicals, since it has been postulated [l] (but not experimentally proven) that the glutathionyl radical (GS·) might be an intermediate in the reaction between vanadium(V), NADH and GSH. We have used electron spin resonance (ESR) and ESR spin trapping methodology for investigating the reactions of GSH, cysteine, N-acetylcysteine and penicillamine with vanadium(V). The results show that the corresponding thiyl radicals are indeed formed in the one-electron reduction of vanadium(V) by all of the above mentioned thiols."

Jan 1, 1990

By R. Carson Dalzell

The use of nuclear fission for chemical process heat offers the special advantage of high temperature, limited only by materials of construction. The process heat may be supplied economically at elevated pressures, since no compression of combustion air is required. For the initial effort in developing a high-temperature reactor, the indirect cycle, using helium as the heat-transfer medium, was chosen. The major problems are the design of high-temperature fuel elements, construction of an exchanger to transfer heat to process streams in the range of 2,500° F., and development of compressors capable of recycling helium at 1,000° F. and above. A conceptual design of a nuclear reactor to furnish process heat for coal gasification has been made. Spherical fuel elements utilizing a graphite structure, impregnated with uranium carbide fuel, were chosen, as spheres offer the possibility of easier loading and unloading of the reactor. Calculations of pressure drop and gas-pumping power for the system are included.

Jan 1, 1959

By W. E. Wallace, V. Castranova, F. Saus, D. Bates, C. A. Hill, V. Vallyathan, M. J. Keane

"Two in vitro systems are being developed to model initial stages in the interaction of respired dusts with the acinar region of the lung. Incubation of quartz and kaolin with dipalmitoyl glycerophosphorylcholine, a major component of pulmonary surfactant, suppresses the prompt C)1otoxicity of both dusts as measured by in vitro enzyme release from pulmonary macrophages or assay by erythrocyte hemolysis. Additional data is presented to quantitate the detoxification of quartz and kaolin by dipalmitoyl lecithin. Subsequent incubation of lecithin treated dusts with phospholipase enzymes results in partial to complete restoration of the assayed cytotoxic potentials, dependent on the lipase activity applied, the incubation time, and the mineral. Restored cytotoxic potential is due to removal of the prophylactic lecithin surface coating and/or due to residual lysolecithin which is produced by the partial enzymatic digestion of lecithin. Data is presented on the contribution of each mechanism to the restored toxicity. Again, this is dependent on the mineral used, the lipase activity applied, and digestion time. Additionally, a system is under development to challenge pulmonary macrophages in culture with native and surfactant treated dusts. A preliminary test of the dipalmitoyl lecithin - quartz rabbit pulmonary macrophage system is presented to illustrate the method.IntroductionRespirable quartz dust exposure is known to cause librotic lung disease; respirable clay dust exposure is less likely to do so as indicated by epidemiologic data on occupational exposures and by animal model studiesP·7) The hypothesis that damage to pulmonary macrophages in the acinar region of the lung by respired dusts is an early event in the disease process requires consideration because kaolin clay and quartz dusts are comparably cytotoxic to pulmonary macrophages in vitro.(3•9)"

Mar 1, 1989

By F. S. Crawford

Although it may be impracticable to adopt standard methods of safe working in all branches of mining, and although it may be impossible to establish a standard for each class of work at each mine, some of the iron-mining companies in the Lake Superior district have found that by adopting certain standard ways of performing certain of their operations they insure both more efficient and safer working conditions. Many companies have adopted the idea that the safe way of doing things is also the most efficient and economical way, and, through the medium of their safety conferences they are trying to find the safest way, and the most efficient way, of performing practically every operation about the mines. This activity will, undoubtedly, be continued at every operation which uses this method of doing safety work, because in the advance of industry changes must be made in the results required from time to time. A review of the safety standards and safety suggestions which have been arrived at by some of the companies in this the greatest iron-mining district in the world, will be of value to companies who are interested in improving the safety of their working conditions. So that attention may be directed to the methods in use, rather than to individual companies, all names have been omitted and companies are referred to only by letter.

Aug 1, 1931

Under the Bureau of Mines Research Contract Number H0252071, Foundation Sciences, Inc. has compared the relative effectiveness of roof bolts installed at an angle over the rib with that of bolts installed vertically at the rib side, The information gathered during this investigation was sufficient to supply supplementary information on the mechanics of roof support systems and the general acceptability of field instrumentation methods. During the 140 days of field investigation, 235 bolts were installed, 45 inclined and 190 vertical, in two adjacent intersections. Of these 235 bolts, 30 were in-stalled with load cells and 38 were tested for anchor capabilities. In addition to this instrumentation, the deformation of the opening was measured by convergence meter on 9 lines throughout the two testing areas, and a borescope and photo-elastic gauges were utilized to obtain information on the roof action beyond the surface.

Jan 1, 1977

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By Peter N. Gabby

A mineral purvey of 40,000 acres of the 42,213-acre Little Humboldt River Wilderness Study Area was conducted by the U.S. Bureau of Mines in 1985 at the request of the U.S. Bureau of Land Management. There are no identified mineral resources but anomalous gold, silver, mercury, and arsenic concentrations were found. The study area is located in Elko County, NV, in the Owyhee Upland geomorphic subprovince. It is underlain by mid- to late-Miocene-age rhyolite, basalt, tuff, vitric ash, and tuffaceous siltstone. On the south side and partly within the study area, a mining company recently (January 1986) located 125 contiguous claims over an area of hydrothermally-altered volcanic rocks that have anomalous surface concentrations of gold, mercury, arsenic, and silver. Anomalous gold-silver concentrations in altered rocks were encountered at several other widely scattered localities in the study area. These elevated metal concentrations and associated hydrothermal alteration indicate gold resources may be present in the study area. A 20-ft-thick bed of diatomaceous earth, which contains 60 to 85 percent diatoms, crops out 0.3 mi north of the study area. Elsewhere, three samples of altered volcanic tuff taken within the study area contain from 46 to 70 percent zeolite (clinoptilolite). The diatomaceous earth and zeolite sampled are not of sufficient quality to compete with materials presently being marketed. There has been no mineral production from the study area, but a caved adit, about 25 ft long, and six prospect pits were found.

Jan 1, 1987

By Xavier B. Starnes

The Dike and Eaton veins in Crittenden County, Ky. (fig. 1), are along northwesterly trending relief fractures that lie between two northeastward striking major faults - the Moore Hill and- the Levias, in Crittenden County, Ky. The veins contain small, narrow, irregular ore bodies of fluorspar with subordinate quantities of sphalerite and galena. Gravel fluorspar was found on the surface in the Eaton vein, and open-cut mining was in progress on the W. M. Conyer property about 1900. Discovery of fluorspar in the Dike vein came much later, about 1933, on the W. H. LaRue tract, but the principal production on the Dike vein started after the discovery of gravel spar in 1938 on the land of the P. J. Gilless estate. Production from the Eaton vein was estimated at 9,400 tons and that from the Dike vein at 15,700 tons, a total of 25,100 tons. A large part of this production was gravel fluorspar from within 50 foot of the surface. Beneath the gravel spar the veins are very narrow, averaging 2 to 2.5 feet in width, and the ore shoots are small. The deepest mine level was 140 feet below the surface, and the deepest shaft 150 foot. Orb was concentrated by log washer or sent unwashed to custom mills at Marion, Ky. about 6 miles distant.

Jan 1, 1950

By R. G. Knickerbocker

[The Electromet l'.ur.::ic'l.l LC:tt:n~ to:!'"' of' the BUl~6au 0: M_nes, Boulder City, ..rev. I invest~.f-'8tes th~ r.: nc= I (l.op itr. in tr.e redon around Boulder Dam, and thi" p2pe:.. ., 'est.3nttl t rt") d.c-velo !l'\CtltR of n seriAl of studies on "Joron uineral~ mario n.~ t~l"'t f1tn.: ... o]

Jan 1, 1940

By H. Kim, R. W. Plummer, T. J. Stobbe, W. G. Jones

"Exposure to airborne dust in coal mines has caused respiratory disease in coal miners. The causal agent in these diseases remains unknown, although the minerals found in and around the coal seam have been implicated. Toxicological studies designed to establish the effect of different mineral combinations and concentrations are lacking because the mineral content of coal mine dust has not been defined. This paper reports the initial results of a study done to characterize the mineral content of the coal mine dust found in a mine in the Upper Freepott seam in Northern West Virginia. Coal mine dust samples were collected using 4- stage cassette impactors at nine locations in the mine. The samples were analyzed by an x-ray microdiffraction film technique supplemented by energy dispersive scanning electron microscopy. Primary size modes of about 17 to 20 micrometers from the samples collected at the haulageway and the returnside of the continuous miner were found. From the returnside of the roof bolter samples, a primary size mode of 12to15 micrometers was measured. The minerals found in high percentages were illite, kaolinite, quartz, and calcite. The distribution of minerals in inter· and intra- location samples showed wide variations. Trends in these variations are presented. Stobbe, T. J.; Plummer, R. W.; Kim, H.; Jones. W.: Characterization of coal mine dust. Appl. Ind. Hyg. 2:95· 100; 1986. IntroductionDisease-associated dusts in coal mine environments continue to afflict miners in today's modern mines. The relationship between exposure to coal mine dust and the development of various respiratory diseases has been well recognized; however, the reasons for variation in occurrence of these diseases among miners in different geographic areas,(1) rank of coal seams,(2-3) and jobs (4) remain uncertain. Several papers have reported on the causal agent in the development of these diseases. Davis (5) found that the percentage of the non-coal minerals present in the lungs of deceased miners increased as the level oi pneumoconiosis became more severe. Reisner (6) reported that cell damage caused by coal mine dust increases with the mineral and quartz content of the dust and with the geo· logical age and rank of the coals. Two studies, investigating the in vitro effects of mineral dusts. reported by Seemayer and Manojlovic (7) also obtained positive correlation between cytotoxicity and the mineral content of coal mine dust. Gormly (8) postulated that destruction of macrophages by certain mineral dusts is the first step in the development of pneumoconiosis. In 1980, Adamis and Timar (9) reported that quartz. sandstone, slate. respirable colliery dust. bentonite, illite, and some kaolins had cytotoxic effects on rat peritoneal macrophages""in vitro."" Walton,(10) however, reported that the presence of high clay, illite, and kaolin mineral exposures reversed the hazards associated with increasing quartz exposures. This finding was supported by Le Bouffant and coworkers.(11) They reported that illite present in coal mine dust strongly inhibited the pathogenic effects of quartz while kaolin had a weaker inhibitory effect."

Mar 1, 1989

By L. C. IlsLey, E. J. Gleim, F. CRAVEN

Electrical apparatus and circuits began to be used in mines about 50 years ago. A search of the literature on mining reveals that in 1882, umping was being done by electricity in some aines of England. One account tells of a small electric locomotive being used in 1882 "to drive eight corves loaded with coal" in a mine near Dresden. In an account of his visit to some English mines, en American in 1892 mentions that he saw underground electric signals, lights, pumps, hoists, and one revolving- cutter-bar 19wall mining machine,. Among the carl electrical installa- tions in the United States was an electric locomotive in the Lykens Valley Coal Co. mine at Lykens Valley, Pa., in 1887. In 1889 the Sperry electric coal digger was being tried out. Tarce mining machines were placed in the Prospect mine, East Palestine, Ohio, in 1890. An electrical pumping plant was put in oneration during 1892 in the Woodward mine of the Delaware, Lacka- rahma & Western Railroad Co. Thus we Almost coincident with the proposed use of this new servant in under- ground workings, came the thought of making it safe in gassy mines. find an account of a design for a protected stationary electric mine lamp proposed by Edison in 1831. Enclosed-type motors rere developed in the United States and shiped to English collieries about 1903. From those early beginnings there has been continuous progress until to-day one finds hundreds of pieces of specially designed electrical apparatus distributed in American coal mines and in mines of nearly all important coal-producing countries. Along with introduction of this equipment grew the idea of the necessi- ty of government aid, in standardization. In most coal-mining countries to- day the governments either directly or indirectly have a considerable in- fluence in guiding the design of electrical equipment intended for use in Pasay mine

Jan 1, 1933

By H. D. Jacobs

The Federal Bureau of Mines, as part of a program to insure future raw material needs for the iron and steel industry, undertook research to beneficiate the oxidized taconites from the western Mesabi range in Minnesota. The data presented were obtained by applying the Bureau-developed selective-flocculation/cationic-flotation process to the second of three oxidized taconite samples. These three samples are representative of an estimated 10 billion tons of ore analyzing 30 to 40 pct iron. The experimental work was performed in a 900-lb/hr pilot plant. Treating the ore sample (36.1 pct Fe) with the Bureau's process produced commercially acceptable concentrates averaging 63.5 pct Fe and 4.3 pct SiO2, with an average iron recovery of 84.6 pct.

Jan 1, 1980