Search Documents

By R. F. Zaffarano

Data presented on the physical characteristics of the reservoir oil, Aneth field, represent the initial phase of a study of Paradox basin reservoir oils being made by petroleum engineers of the Federal Bureau of Mines, Petroleum Research Center, Laramie, Wyo. The purpose of the study is to determine the original reservoir-oil characteristics in several important new discoveries in the Paradox Basin and to investigate correlations between the properties of these reservoir oils and structural or areal position within the basin, If migration is limited and oil accumulates near its source, then it seems probable that few differences should be found in the composition and characteristics of reservoir oils occurring in given age rocks and within the confines of a geological basin. Within these limits, conditions that effected the formation of oil and its transfer from parent to storage rocks probably were rather uniform in an area the size of most of our geological basins. However, if oils should migrate considerable distances, it seems logical to expect that the relative quantities of gas and liquid components may differ in traps occurring along the direction of migration, corresponding with the theory of differential entrapment (5).4/

Jan 1, 1959

By Philip C. Tully

This Bureau of Mines report contains experimentally determined vapor-liquid equilibria data for a helium-nitrogen-methane mixture with a nominal composition of 15, 60, and 25 mole-percent, respectively. Measurements of the equilibrium phase compositions were obtained by means of a windowed cell, in conjunction with an automated chromatograph and a special analyzer for low helium concentrations. The data presented include a comprehensive table and eight graphs depicting phase compositions, vaporization ratios, and correlations with a previous study of two helium-nitrogen-methane mixtures of different compositions.

Jan 1, 1976

By Henry M. Harris

A study was made by the Bureau of Mines to determine if shapes of oxide-glass compositions could be roll-formed at high temperatures, and to find the conditions required for adequate formability. A unit with directly connect' furnaces and heated rolls that allowed forming of most of the compositions developed. Glasses of the feldspar type were chemically unreactive with the alumina grains, and allowed the best roll forming. Optimum forming was attained at temperatures of 1,400° to 1,530° C, with compositions containing 30 or 40 percent feldspar and 60 or 70 percent alumina. Formability was better when compositions contained minus 325-mesh materials, rather than coarser or finer powders. In many cases, roll-formed shapes had physical properties equal to or better than the normally sintered shapes of the same composition.

Jan 1, 1967

By Barry L. Warner

This program involves the evaluation of means for suppressing fires on underground coal mine conveyor belts. Full scale conveyor belt fire tests were conducted to determine the requirements of automatically actuated water sprinkler, high expansion foam, and multi-purpose dry powder extinguishing systems, and of various fire detection devices, necessary to adequately protect underground belt heads. The program included the development of a suitable MI scale conveyor belt test fire, conducting of fire tests in which extinguishing and detection systems and equipment were evaluated, and testing to evaluate the effects of the coal mine environment on detection equipment. Preliminary testing conducted to develop a suitable test fire revealed that fire can propagate on some conveyor belting classified as fire-resistant. New fire-resistant PVC and new non-fire resistant rubber belts were used in the full scale fire tests. These tests indicated that a single branch line sprinkler system with relatively low water pressure provides adequate belt head protection. High expansion foam and multi-"purpose dry powder extinguishing systems as presently specified by regulation were found to be suitable for belt head protection, although care is required with powder systems to assure adequate distribution. Thermal type detection devices were found to be most practical for conveyor belt protection, with combustion products and optical detection methods having serious disadvantages.

Jan 1, 1974

By Levent Ozdemir

The results of a laboratory research program aimed at the development of a water jet assisted drag bit cutting system for coal mine applications are presented. Two types of drag bits, a conical and a plow bit, were tested in a hard sandstone rock with jet pressures of up to 20,000 psi. Jet locations investigated were in-front and behind the bit. For each jet mounting location, three jet impingement distances with respect to bit tip were tested. The closest jet impingement location to bit tip was found most effective, providing the greatest force reductions on the bit. Overall, significant bit force reductions up to 50 percent were obtained with jet assist. Also observed was a drastic reduction in airborne dust when jets were employed.

Jan 1, 1986

By M. M. Wong

Electrolysis of titanium carbide and a material consisting of titanium, carbon, nitrogen, and oxygen as soluble anodes in Used electrolytes was investigated by the Bureau of Mines for the preparation of crude titanium metal. Tests made in all-chloride electrolytes showed only a low recovery of titanium as well as a substantial volatilization of titanium trichloride (TiC13) when present in the electrolyte. Electrolysis at 750° to 850° C in a mixture containing 85 percent NaC1-15 percent potassium floutitanate (K2TiF6) yielded as high as 91 percent recovery of titanium from titanium carbide and 62 percent recovery of titanium from the titanium-carbon-nitrogen-oxygen material. Problems associated with the preparation of crude metal by fused-salt electrolysis are discussed. The crude metals produced from both anode materials were electrorefined in a sodium chloride-titanium chloride (NaCl-TiC12) electrolyte, and ductile titanium metal was obtained.

Jan 1, 1963

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By W. Hodge Caraway

This report presents the results of an evaluation of several indirect methods of measuring the water content of oil-reservoir rocks. The water content of oil-base cores is considered to be most nearly representative of the water content of the undisturbed petroleum reservoir and therefore, the direct method of measuring the volumes of water in cores cut in oil-base drilling fluid was adopted as a standard for comparison. The indirect methods evaluated included (1) displacement through a semipermeable membrane by air, (2) centrifuge, (3) evaporation, (4) mercury injection, (5) chloride dilution and (6) electric logs. Approximately 270 samples of cores from petroleum-reservoir rocks were used in the study. The cores, most of which were cut with oil-base mud in the hole, were taken from oilfields in California, Texas Gulf coast, Colorado, Oklahoma, and Alaska.

Jan 1, 1959

By E. G. King

Thermodynamic calculations involving the oxides of tungsten and molybdenum have been hampered by lack of accurate entropies and high temperature heat contents. This paper presents work by the Federal Bureau of Mines on new low-temperature heat-capacity data leading to the evaluation of the 298.15° K. entropies of tungsten dioxide and tungsten trioxide, as well as high-temperature heat contents (above 298.15° K.) of molybdenum dioxide, molybdenum tri-oxide, tungsten dioxide, and tungsten trioxide. Included are heats of fusion of the two trioxides. The heats of formation at 298.15° K. of these four oxides are tabulated as measured by Mah4 5/ of this laboratory. Included also are the 298.15° K. entropy of Mo02 measured by Kin 6/ of this laboratory, and that for Mo03 according to Kelley and King.7/ These basic data provide a consistent compilation from which to perform accurate thermodynamic calculations involving these compounds. No previous low-temperature- heat-capacity measurements have been reported for tungsten dioxide. Seltz, Dunkerley, and DeWitt8/ measured the low-temperature heat capacity of tungsten trioxide. The only previously-reported high-temperature heat-content measurements for any of the oxides were conducted by Cosgrove and Snyder,9/ who measured molybdenum trioxide to 1,300° K.

Jan 1, 1960

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By H. D. Hess

This report presents the results of laboratory mineral evaluations conducted by the federal Bureau of Mines under the joint sponsorship of the U.S. Atomic Energy Commission (AEC) and the Bureau a! Ships, U. S. Department of the Navy. The major purpose of this investigation was to examine and evaluate zirconium minerals representing sizeable deposits in an effort to locate com¬mercial sources of high-hafnium ores. Although determination of the hafnium content was the principal objective, each of the zirconium minerals also was analyzed for combined zirconium-hafnium oxide, silica, uranium, thorium, yttrium, and cerium. The general laboratory procedure involved microscopic examination of the test samples, concentration of the hafnium-bearing zirconium mineral by standard laboratory techniques, and analysis of the derived concentrate by quantitative microscopic, chemical, and X-ray spectrographic methods. Of the several hundred samples tested under this program, 147 are discussed in this report, including 94 from domestic occurrences and 53 from widespread foreign sources.

Jan 1, 1962

By F. F. Netzeband

This report relates to the sulfur industry of seven States--Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas--and is part of a national study of the sulfur industry by the Bureau of Mines. Markets as used in this report are divided into two components for individual analysis-- (1) supplier markets which include regional Frasch and byproduct sulfur producers and (2) consumer markets which include processors and manufacturers requiring sulfur in their operations The term sulfur as used in this report includes brimstone, native sulfur, elemental sulfur, or sulfur equivalents.

Jan 1, 1964

By C. W. Smith

The U.S. Bureau of Mines; Tuscaloosa Research Center, in cooperation with the U.S. Army Corps of Engineers under interagency Agreement No. 14-09-0078-1510, conducted a comprehensive sampling program of 10 upland disposal sites along the Alabama, Black Warrior, and Tombigbee River systems in Alabama. Samples from each site were characterized according to particle size, chemical analysis, mineralogical content, and potential end use. Additionally, samples were subjected to the Toxic Characteristic Leachate Procedure to determine the presence of potentially harmful heavy metals. Based on the results of these studies, each sample was determined to have properties amenable for use as aggregate in general-purpose portland cement concretes and certain asphalt concrete applications.

Jan 1, 2010

By Phillip R. Moyle

In 1985 the U.S. Bureau of Mines evaluated the mineral resources of the Sheep Creek West Wilderness Study Area (ID-111-36A), Owyhee County, ID, for the U.S. Bureau of Land Management. The Wilderness Study Area consists of 11,680 acres centered approximately 20 miles south of Grasmere, 10. It contains no mines, claims, or prospects. No mineral resources were identified; however, a geode occurrence within and adjacent to the Wilderness Study Area, and minor amounts of placer gold along Sheep Creek, may be of interest to rorkhounds and recreational gold panners.

Jan 1, 1986

By Gerhard Braüner

The present knowledge on ground movements and mining damage is mainly based on observations made when mining seamlike deposits. The studies, rules, and regulations in different countries agree in that the differential ground movements, especially the strain, account for the damage to structures. Accordingly, large buildings are particularly susceptible. The opinions on what amount of ground deformation induces what degree of structural damage are not quite uniform. Mining damage can be reduced or prevented by structural and/or underground precautions. The latter comprise measures for generally reducing the ground movements (leaving pillars, filling, partial extraction) and for reducing temporary movements (rapid extraction, specially arranged workings). Because the differential movements decrease with increasing depth of mining, safety pillars are largely dispensable at greater depths. Shafts are mainly affected by the vertical derivatives of rock displacements, but extraction in the vicinity of shafts is feasible even under difficult conditions. The theoretical concept of the ground movement process established in part 1 of this work is in qualitative agreement with the facts herein observed. As a quantitative approach, it should be applied to calculating ground surface movements rather than rock movements about underground openings. It can be extended by introducing more detailed strata characteristics.

Jan 1, 1973

By C. H. Elder

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coal bed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 fts/day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By K. C. Dean

The Bureau of Mines, following passage of the Solid Waste Disposal Act of 1965, was authorized to conduct research on methods for utilizing, stabilizing, or reclaiming mineral wastes. This report summarizes laboratory research conducted by the Bureau and cooperative field studies made with the mineral industry to reduce the environmental impacts of air and water pollution deriving from mineral wastes. Utilization research showed that both dry-press and steam-cured building bricks and ceramic tile could be made from copper mill tailings and other discarded mineral wastes. Sponge iron was produced from steel mill and amination industry wastes, and valuable mineral products were extracted from such diverse sources as flue dusts and uranium tailings. Mineral wastes were combined with agricultural and/or sewage wastes to make artificial soils that have the potential of resolving several disposal problems by production of a useful commodity. Physical, chemical, and vegetative stabilization methods were evaluated, singly and in combination, for reclamation potential on copper, uranium, lead-zinc, and asbestos tailings. Suitable methods were developed in the laboratory for overcoming major adverse conditions of these wastes such as salinity, heavy metal toxicity, acidity, basicity, lack of nutrients and organics, and unstable surfaces. Field testing of these methods was performed on a variety of mineral wastes. Costs for the various stabilization and utilization-procedures developed were also determined.

Jan 1, 1986

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By H. B. Hill

The discovery of the Oklahoma City field and its .rapid development into one of the major oil-producing districts is an outstanding epoch in the history of the petroleum industry not only of .Oklahoma but also of the United States. The relatively great depth to which the wells were drilled and the large initial production of high-gravity oil are of special significance. The field has boon under proration almost from the time that its development began, and many new production problems have developed out of the changed conditions of operation. The discovery well was first tested in December 1928 at a depth of 6,402 feet, with an initial production of 4,847 barrels of 38.5° A.P.I. gravity and several months later was completed at a depth of 6,624 feet. The large initial production, the high pressure, and the large gas volume in the different horizons of the discovery well suggested the potential possibilities of gas and oil, production in formations of Pennsylvanian and pre-Pennsylvanian age.

Jan 1, 1933