Search Documents

By F. B. TOUCH

This bulletin deals with a topic that is exceedingly wide, and will doubtl~ be under consideration and discussion so long as there are enough known deposits of oil and gas remaining in the earth to make their revelopment profitable. The Bureau of Mines has repeatedly called attention to the importance of protecting oil or gas sands from the encroachment of water, and the purpose of this paper is to summarize existing knowledge of methods and devices. Water may gain access to an oil-bearing formation from several sources-from water sands above or below those. containing the oil, or by encroaching through the oil sands as the oil is withdrawn. In short, it may enter a well from the "top, bottom, or side." Such ingress of water is a most serious detriment to the recovery of oil from the ground. As the art of drilling and developing oil properties has progressed, increasing thought, labor, and money have been expended on various methods, devices, and equipment for arresting the migration of water from its normal subsurface position into the porous strata containing valuable oil or gas accumulations. At an early stage in the oil-field development of California, it became evident that considerable modification of accepted drilling practices was necessary in order to meet the conditions imposed by the poorly consolidated shale, clay, sand, and bowlder beds penetrated, as well as the hard layers of sandstone and calcareous shale, which vary greatly in thickness, hardness, and frequency. These hard streaks are commonly called " shell," and are so reported in the well logs. As deeper and deeper territory was prospected, drillers from the older fields of the Ea,st, as well as from Texas and Louisiana fields, took part in the operations. Xhe practice evolved was thus based on the wide experience of a most cosmopolitan group of men who, considered as a group, were not hampered by being limited to the knowledge of the practice at any one locality.

Jan 1, 1918

By Sumner M. Anderson

THE importance of the mineral industries of the Latin American area in 1964 may be evaluated in respect to a number of points of reference, a few of which are measurable and appropriate for examination. With regard to the region's contribution to total world production, it accounted for total 1964 world output of natural nitrates (from Chile), and about 97 percent of the optical and electrical grades of quartz crystal (from Brazil). The region supplied over 20 percent of world output of 7 other mineral commodities and accounted for 4 percent or more of world output of 19 other mineral products. Among major commodities, the area, occupying 15 percent of the earth's land surface, supplied within 3 percent of that proportion of the world's output of copper, lead, tin, zinc, barite, and crude petroleum. Incomplete compilation of production data, particularly that of nonmetallic minerals, precludes production estimates on some items for the area ass whole, and therefore the importance of Latin America as a world producer of some additional commodities may not be clearly assessed. For example, most of the countries of the area collect only incomplete data or no data at all on the production of clays and other ceramic materials, sand and gravel, dimension and crushed stone, lime, ornamental and precious stones, perlite, vermiculite, carbon black, coal tar products, and petrochemicals. In the case of many countries of the area, the value of production of one or more of these commodities greatly exceeded that of other mineral industry products that are carefully reported.

Jan 1, 1966

By R. S. Dean

The possibility of cheap electric power for a number of mining areas in this country has suggested to many the idea of electric smelting of nonferrous ores in small units at or near the mines. The electric smelting of nonferrous ores was tested fairly thoroughly 20 years ago by United States Bureau of Mines and by others, and the fact that it did not achieve continuing workable success in any instance is sufficient proof that it offered no advantages at that time.

Jan 1, 1937

By Will H. Coghill, F. D. DeVaney

"Many of the iron ore deposits on the western end of the Mesabi Range Minnesota consist of the so-called ''wash ores."" Because of their high silica content these ores must be washed or concentrated to make them merchantable. Washing plants have been in operation for 20 years, during this period large quantities of tailings have accumulated in tailings ponds. These tailings contain the aggregate millions of tons of iron oxides which, if recovered, would greatly to the available tonnages and to the revenues of the mining companies. It the purpose of this paper to outline give results of concentration tests on tailings.In order that the reader may understand more clearly the type of material under consideration, a short description of the characteristics of the wash ores of the Western Mesabi Range and a brief resume a washing methods that have been are now being employed will be given. Appleby and Newton4 In their description of the district and of the ores say:The Western Mesabi district embraces the territory west of the town of Nashwauk in Itasca County. The territory to the east of this dividing line is known as the Central and Eastern Mesabi district. This subdivision is rot wholly arbitrary. While the ore bodies in the two districts resemble each other in. shape, size, and general structure, there is a marked and very important difference in the character of the respective ores. For purposes of comparison, the western deposits have been called washable ore bodies, and the central and eastern, standard ore bodies. The latter ores are the result of natural concentration processes which have teen carried far enough to produce a large proportion of high-grade ore Wet can be marketed direct; the Western Mesabi ores present a lesser degree of natural concentration and are as a rule of too low grade to admit of marketing without preliminary treatment. In many cases the grade can be improved by washing, hence the material is called washable ore. Exceptions to thin general rule may be noted in both districts. Many of the Western Mesabi ore bodies contain quite a proportion of merchantable ore. There are also portions of central and eastern Mesabi ore deposits which are of low grade and which can be improved by washing."

Nov 1, 1930

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By John W. Cole

The Bureau of Mines conducted a trenching and sampling project during 1947 on the tungsten-rich granodiorite that outcrops in Henderson Gulch, Montana. During the course of this investigation, interest was attracted to the Sunrise copper-gold mine in metamorphosed limestone in the north slope of the gulch. The mine was examined by S. H. Lorain, Chief, Mining Division, Albany Branch, in May 1948. A trenching and drilling program was recommended to develop a parallel vein indicated by outcrops to lie below the principal productive Queen vein. In the meantime, the Queen Mining Syndicate initiated a trenching program that exposed high-grade lead-copper-silver-gold ore in a nearly vertical vein that strikes N. 600 E. to east. A core-drilling program to develop this vein was initiated in September 1948. This report presents the factual data obtained from the trenching and drilling operations. The Sunrise mine was discovered about 1890. Production has been estimated to be $120,000 in gold from 40,000 tons of ore mined during the period 1892-1903. The tailing from this operation was treated by cyanidation in 1912, with a reported recovery of $3.50 to $4.00 a ton from 15,000 tons of material. Subsequent production of sulfide ore was 7,396 tons treated by smelting, with recovery of 1,569.42 ounces of gold, 10,003 ounces of silver, 352,899 pounds of copper, and 354 pounds of lead.

Jan 1, 1950

By W. A. Calhoun, M. M. Fine

"One of the most important wartime activities of the Bureau of Mines was the search for new sources of mineral necessary to the prosecution of the war. Part of that effort was in the form of metallurgical service extended to other government agencies engaged in purchasing and stock piling some of the more critical and strategic materials.Fluorite was one of the materials stock piled by the Metals Reserve Company. The fluorite was usually in the form of coarse metallurgical con¬centrate purchased in the United States and abroad. The material was stock¬piled to insure an adequate reserve of fluorite for the metallurgical industries. The domestic production of metallurgical fluorite containing a minimum effective calcium fluoride content of 55 percent,4/ however, gradually increased until production was at least equal to consumption. The stock-piled metallurgical fluorite, therefore, soon became a surplus commodity.On the other hand, the supply of acid-grade fluorite, containing a minimum of 97.5 percent calcium fluoride and n maximum of 1.5 percent silica,5/ was never entirely adequate. Increased consumption of acid-grade material in the aluminum, petroleum, and chemical industries kept that material on the critical list during the war.Under the circumstances, it was felt that a study of the possibility of producing acid-grade fluorite from the metallurgical stock piles would be of some benefit to the war effort. Consequently, samples of fluorite from several of the Metals Reserve Company stock piles were tested by the Bureau of Mines at the request of the War Production Board.Two groups of samples were submitted for testing. One consisted of metallurgical fluorite purchased from Mexico and stock-piled in the El Paso and Laredo, Texas, stock piles of the Metals Reserve Company. The second group of samples was from the stock piles at Gila, N. Mex.The sample submitted from the El Paso stock pile consisted of about 5,000 pounds of minus 4-inch material. Mineralogically, the sample consisted of fluorite contaminated by calcite, chert, quartz, and small amounts of iron and alumina. Although some of the fluorite was reasonably free from gangue at minus 1-inch, much of it remained locked in sizes as fine as 65-mesh.The Laredo sample was about 5,000 pounds of material from five different piles. The samples from each stock pile, A to E, inclusive, were analyzed separately to determine whether the grade of the material in the piles varied markedly. As there was little difference in the analyses, the samples were combined in proportion to the tonnage represented to make a composite sample for testing. The composite sample consisted of fluorite with small amounts of quartz, calcite, and barite. Most of the fluorite was the dark-colored, opaque variety. A small amount of iron-oxide staining was present, and traces of muscovite, clay, pyrite, and tourmaline were noted. The quartz was present as crystals in vugs, and as finely disseminated grains in the fluorite. The druzy quartz and the calcite were free at minus 10-mesh, but the disseminated grains, some of which were 1 to 15 microns in size, were not entirely free at minus 270-mesh. A petrographic estimate indicated that 65 percent of the silica was locked in the 150- to 200-mesh."

Jun 1, 1946

By Ellis S. Hertzog

The material published in this report is part of a special study of some of the chemical and physical properties of Alabama coals. The complete study included friability and grindability determinations, high and low temperature assay distillation tests, and ash fusion-temperature determinations. Proximate and ultimate analyses and. calorific values of the coal samples also were obtained. This paper is concerned only with grindabilities, although proximate analyses have been included to give a better picture of the problem as a whole. The growing interest in grindabilities of coals is a result of the increase in use of pulverized fuel in rescent years. The tenative ball-mill grindability method D408-35T4/ was used in making all the determinations. The method of sampling and the technic of the testing procedure is described in Considerable detail in this report because the procedure was established quite recently. The ball-mill grindability index is a measure of the ease with which coal may be ground, which may be an important factor in estimating pulverizing costs. Up to the present time few data on the grindability of Alabama coals have been published. The data in this paper show that the Warrior and Cahaba fields exhibit a wide range of grindability in their coals. The mines tested are well distributed throughout the productive areas of these fields, and it is possible to make rough estimates of the grindabilities of coals not listed in this report from the data given for mines situated in the same vicinity.

Jan 1, 1938

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

Recent Bureau of Mines research in earth grounding safety is documented in three separate papers. First, guidelines for the design of a 5- ohm borehole ground are presented. Next, an inexpensive practical means to construct a low-resistance bed in high-resistivity soil is described. Finally, a procedure that employs a commercial resistivity meter to measure shock potentials around grounded objects is explained step-by-step. These papers complement the material presented at an earlier technology transfer seminar and published as IC 8767.

Jan 1, 1985

By D. D. Harbuck

To decrease reliance on foreign sources for the strategic and critical metals gallium and germanium, the U.S. Bureau of Mines identified and developed processing technology for two domestic sources of these metals: a Tennessee zinc residue and a Utah ore. Sulfuric acid (H2S04) solutions were used to solubilize gallium and germanium in both sources. Statistically designed experiments showed that the most important parameter for high metal extraction from zinc residue was the H2S04 concentration. At a concentration of 2.9M H2S04, 95 pct of the gallium was extracted, and at a concentration of 0.6M H2S04, 73 pct of the germanium was extracted. Controlled H2S04 concentration was also the key for high metal extractions (97 pct Ga, 87 pct Ge) from the Utah ore. Such control was achieved using a two-stage countercurrent leach circuit. Testing showed that the insoluble germanium in both the residue and ore was tied up with silica. Several methods for overcoming this problem are given. To recover gallium and germanium from the leach solutions, the solvent extractants octylphenyl acid phosphate (OPAP) (for gallium) and LIX 63-OPAP (for germanium) were identified. These extractants were tested in separate, continuous, solvent-extraction circuits yielding a gallium recovery of 94 pct and a germanium recovery of more than 90 pct.

Jan 1, 2010

By Lijun Xu, Jan M. Mutmansky

"Mutmansky, J.M. and· Lijun Xu, 1989. Some observations on particulates collected in underground coal mines using diesel and non-diesel equipment. Min. Sci. Technol., 9: 207-218.The results obtained when sampling twenty underground coal mine sections, each in a different mine, are outlined. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a fairly detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons of the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines lising diesels only for outby utility haulage. Particulates in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be drawn from the limited data, a more detailed study of particulates may provide a better picture of particulate loadings.IntroductionThe subject of particulate emiss1ons from underground diesel equipment is currently a very important topic as health concerns and regulation of diesel particulate emissions have created new environmental problems for mine operators. The amount of particulate matter originating from diesels has not been extensively measured and problems of differentiating coal and mineral dust from diesel particulates make existing data questionable.However, it is necessary to make an assessment of the problem in order to solve it. It is known that particulates from diesel engines are solid aerosols formed in the combustion process. Technically, this places the particles in the category of fumes. It is also known from tests where no mineral dust could be a factor in the measurements that about 90% of diesel particles are less than 1 µm in aerodynamic diameter [3]. To measure the diesel component of a coal/diesel particulate to measure, Johnson et al. [2] have developed procedures for utilizing laser Raman spectroscopy. The determination of diesel content in a coal/diesel mixture is difficult due to the chemical similarity of the two organic materials. However, laser Raman spectroscopy, which is often used for identification of organic materials, has potential if the Raman spectra for the two materials are different and unique. The study concluded that an accuracy of ±~% could be achieved for mixtures containing up to 55% diesel particulate. The method is relatively complex and would need further development for routine application."

Jan 1, 1990

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 271 natural gas samples from 22 States collected during calendar year 1982. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of the investigation of the occurrences of helium are published annually to make the information available to the petroleum industry and the general public. Twenty-six publications have presented the results of 13,051 gas analyses vide prior to 1982. The first 3 bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26) containing 7,833 analyses of samples collected since 1960.

Jan 1, 1983

By John R. Reigart

The Tri-State district, as its name indicates, is composed of portions of three States, the southeastern corner of Kansas, the northeastern corner of Oklahoma, and an adjacent strip of Missouri east of these portions of Kansas and Oklahoma. An area approximately 40 miles long in a northeasterly-southwesterly direction, and 30 miles wide at right angles thereto, containing minable occurrences of ore at widely scattered locations, comprises the district. However, what has been and is the main productive area, is a strip about 35 miles long and 10 miles wide, which begins at Miami, Okla., as its southern extremity and runs in a northeasterly direction through Commerce, Picher, and Hockerville, Okla., Baxter Springs and Galena, Kans., and Joplin, Webb City-Carterville and Carthage, Mo. Almost the entire present production comes from the area between Commerce and Baxter Springs.

Jan 1, 1932

By M. H. Marvin

This report presents the results of a program to develop backfilling techniques to mitigate undesirable effects of hydraulic borehole uranium mining. Large underground cavities, formed during the borehole mining process, can be backfilled to prevent ground subsidence and to allow mining of adjacent uraniferous sandstone. Three backfilling techniques were tested in the laboratory and in the field: bulk dumping of slurry into the borehole from ground level, slurry injection under water, and slurry injection above the cavity water level. These techniques were tested with sand and with sand and one percent cement (by weight) mixtures. The project was accomplished in four tasks: equipment preparation and transport, mining operation to generate a full-sized cavity, backfilling operation, and assessment through core samples and subsidence checks. The concentrations of cement mixed with sand proved to be inadequate to bond the sand. Bulk dumping resulted in a 30-degree angle-of-repose, much too steep to completely fill the cavity. Both slurry injection techniques filled the cavity satisfactorily. However, underwater injection is the recommended backfilling technique because the borehole water level does not need to be pumped down during backfilling. The borehole itself was filled by bulk dumping of slurry. In conclusion, backfilling of borehole mining cavities is entirely feasible, and the preferred method is slurry injection under water.

Jan 1, 1979

By McHenry Mosier

This progress report on a national survey of the use of detachable bits in metal mines covers 10 mines. It presents comparative costs for drilling with conventional and detachable bits, describes the reconditioning of drill steel, and gives various data on rock drilling at these particular mines. Reports to follow will include similar data on drilling at other metal mines in the United States. ACKNOWLEDGMENTS This report is based on costs and data developed and furnished by the operators of the mines visited. The author is greatly indebted to the officials and staff members at these mines for their cooperation and assistance.

Jan 1, 1936

By Gary A. Kingston

This examination of Pacific Northwest (Idaho, Montana, Ore on, and Washington) ferrous scrap-industry opera ions, principally those in Oregon and Washington, points out factors influencing the supply and consumption of scrap materials, such as the complete dependence of steel ingot producers in these States on scrap as a metal raw material and the sizable quantity of scrap exported from Seattle and Portland to Japan. The pattern of the industry is presented as a movement of materials from their diverse sources to the consuming market. The geographic locations of the consuming industries in relation to the area generating scrap materials and the movement pattern of the supply from source to destination strongly influences the cost of the commodity. The best measure of the scrap supply available in an area is experience in terms of how much scrap was withdrawn at a given price. Scrap availability is not finite, because the return of materials as scrap is secular and influenced by constantly varying market conditions. Steel ingot producers use 75 percent of the approximate 500,000 tons of scrap consumed in Oregon and Washington; steel foundries take 15 percent of the total; and iron foundries, ferroalloy plants, and other miscellaneous consumers utilize the remainder. Also, from 1955 to 1960 an average of about 200,000 tons has been exported annually from Oregon and Washington. The foreign exports are supplemented by lesser .shipments to other steel producing States, principally in the western United States. From 1955 to 1960 the preferred and higher value heavy melting scrap grades accounted for about 60 percent of total withdrawals which varied between 600,000 and 950,000 tons annually. Total scrap withdrawals from Oregon and Washington are projected to 1.8 million tons by 1985, 60 percent (1.1 million tons) of which will be heavy melting grades. No. 1 heavy melting scrap is most attractive to scrap consumers at $35 per ton or less. Price-supply relationships compared with projected scrap requirements indicate future prices possibly over $35 per ton. High prices over a long period could motivate the Pacific Northwest scrap consumers to produce steel from iron ore. However, technologic changes taking place at integrated steel plants could reduce scrap withdrawals from the Pacific Northwest, which might keep the scrap price sufficiently attractive to obviate production of competitive iron products by the Pacific Northwest scrap consumers.

Jan 1, 1964

By A. C. Fieldner, W. A. Selvig

Information concerning the fusibility of coal ash has become of considerable value to the consumer of coal, mainly in connection with the troublesome formation of clinker resulting from the melting of the ash constituents of the burning coal. The growing interest in such data has led the Bureau of Mines to make a general survey of the "fusing" or "softening" temperatures of the ash from coals of the United States. It is hoped that this information when used together with the large number of coal analyses published 1 by the bureau will assist the consumer of coal in comparing different coals, and in selecting the coal best adapted for his purpose.

Jan 1, 1922

By L. B. Pankratz

Thermodynamic data on carbides, nitrides, and other selected substances were reviewed, evaluated, and compiled at the U.S. Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, -(G° - H298)/T, ?Hf, ?Gf, and log Kf are given in tabular form. Cp°, H° - H°248, ?Hf°, and ?Gf° are also expressed algebraically.

Jan 1, 1994