Search Documents

By F. E. Spencer

Calculated equilibrium data are presented for three phases in the flue gas stream from a hypothetical open cycle MHD generator. A typical coal is "burned" with 1.0 gram-mole K2O seed per kilogram coal and with 101 percent of stoichiometric air. Tables of composition and the overt thermodynamic properties, enthalpy and entropy, are given for the temperatures 2200 (-100) 1100 kelvins, pressures 1.0 and 1.5 atmospheres, and slag rejection figures of 90 and 75 percent.

Jan 1, 1973

Limestone formations in the United States can be subject to relatively high horizontal stresses due to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rockfall hazard. Rockfalls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings have an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orientating the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and offsetting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

Jan 1, 2008

By Ferdinand Roehlich

An evaluation of the use of manually activated, installed,. dry chemical fire protection systems on underground metal and nonmetal mine vehicles is described. In addition, an assessment of the possible health risks posed by the dry chemical extinguishing agents used in such systems is provided. Work involved installation of fire protection hardware on an operating piece of underground metal/nonmetal mine equipment and, via actual fire tests, a determination of the effectiveness of the hardware in extinguishing on-vehicle fires. Two fire protection systems were installed on a Caterpillar 988 front-end loader in St. Joe Mineral's Fletcher mine, near Viburnum, Mo. Both a fully pressurized Safety First CM-20 and a nonpressurized cartridge actuated Ansul A-101 were installed for comparative purposes. Both systems operated satisfactorily during an 8-month endurance trial period which preceded the actual fire tests. Each system was able to extinguish an 18" x 4" class B test fire placed in the engine area of the machine. The health hazards analysis of dry chemical powder consisted of a detailed search of published literature relating to these multipurpose agents. This data was verified via a controlled laboratory analysis of two monoammonium phosphate based powders (Safety First Unikem and Ansul Forey) and an analysis of air samples collected at various locations on the test vehicle during the fire tests. Although the powder was found to be nontoxic, two potentially dangerous thermal decomposition products were identified--ammonia and phosphoric acid. However, later analysis indicated that an operator would not be exposed to dangerous concentrations of either compound if he were to remain outside of the powder cloud. A "Selection and Use Manual for Manually Activated, Fixed Fire Suppression Systems on Underground Metal and Nonmetal Mining Equipment" was prepared both as an, appendix to the report and for distribution under separate cover.

Jan 1, 1977

By MINE SAFETY BOARD

RECOMMENDATIONS OF THE UNITED STATES BUREAU OF MINES ON CERTAIN QUESTIONS OF SAFETY AS OF FEBRUARY 3 , 1933

Jul 1, 1933

By G. G. Campbell

The Bureau of Mines in cooperation with Quaker State Refining Corp. conducted two underground-combustion oil-recovery experiments in the Venango Second sandstone in the Reno pool, Foster-Rena-Oil City field, Sugar Creek Township) Venango County, Pa.) to determine the applicability of the process for reservoirs producing Pennsylvania-grade paraffin-base crude oil. Tests were terminated when analyses of produced gas showed that a self-sustaining combustion front did not exist. It was thought that insufficient fuel had been deposited in the formation. Laboratory retort tests made after the second field test was concluded showed that crude oil from the Reno area would deposit enough fuel to support combustion if air flux, temperature, and time were maintained within defined limits.

Jan 1, 1967

By V. T. Dow

In April 1957 the Bureau of Mines instituted a reconnaissance of titanium-and zirconium-bearing heavy sandstone deposits in the Four-State area of Utah, Wyoming, New Mexico, and Colorado. This report summarizes the study. Eighty-two deposits or groups of deposits, containing an estimated 27,920,000 tons of titaniferous sandstone, were examined in the Four-State area; 16 in southern Utah, 19 in Wyoming, 33 in New Mexico, and 14 in southwestern Colorado. The 16 deposits examined in Utah contain an estimated 1,043,000 tons with an average grade of 17.98 percent TiO2, 5.67 percent ZrO2, 20.98 percent Fe, and 0.09 percent equivalent Th02. The 19 deposits investigated in Wyoming are estimated to contain 21,873,000 tons of titaniferous sandstone having a weighted grade of 5.22 percent 702, 0.55 percent ZrO2, 24.8 percent Fe, and 0.01 percent equivalent Th02.

Jan 1, 1961

These inspection standards have been prepared for use in the Federal inspection of bituminous and lignite mines. They are a revision of "Tentative Coal-Mine Inspection Standards," published as Bureau of Mines Information Circular 7204 in February 1942 and employed a guide for Federal inspections. Numerous changes have been made in the original standards owing in part to recognition of shortages of some types of safety equipment due to the war, in part because of need of additional standards to cover certain mine conditions' arid' practices, and in part to conditions not foreseen when the original standards were prepared. About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however; failure to carry out the suggestions made in such of the other standards as are applicable may also' lead' to the loss of lives.

Jan 1, 1943

By Lloyd A. Morley

Proposed advantages and disadvantages of low-voltage shielded trailing cables are formulated utilizing the literature and industry sources. A partial analysis of these proposed advantages and disadvantages is completed through a review of the literature. Cable costs are assembled from mine operators, cable and splice manufacturers, and actual cable purchases. To confirm each advantage and disadvantage, an underground test site is established, and testing is performed here and in the laboratory. All testing procedures are completely described. The results of this investigation are reported and used to formulate recommendations attendant to low-voltage shielded cables. Suggestions for installation, handling, and maintenance are presented.

Jan 1, 1977

By J. W. Thompson

This work is a codification and annotation of the Congressional enactments relating to minerals, mineral lands, and mining. It covers every enactment of Congress from the original ordinance of 1785 to the present time, as well as all sections of the Revised Statutes of the United States relating to these subjects. These laws are grouped according to their general subject matter, and are arranged thereunder in numerical or chronological order. Many of the mining statutes include matter not pertinent to the subject, and only those parts of such acts are quoted as will properly show their relation to minerals and mineral lands and indicate how they should be construed. Some mining acts have been repealed or have become obsolete, and others have become incorporated substantially in sections of the Re- vised Statutes; but these are retained in order to show the changes made, and the constructions placed thereon by the courts are given as aids in construing the new or repealing acts. The annotations consist of legal propositions abstracted from the decisions of the various courts and executive officers of the Govern- ment that have interpreted the sections and statutes so codified. These legal propositions are arranged under the different sections and acts with appropriate headings, titles, and subtitles, in logical order, exhibiting the present status of each particular section or act and its application to the subject of mines and mineral lands. The annotations do not purport to be abstracts of decisions on the sub- stantive law of mines and mining generally, but are limited strictly to the interpretation placed on a given section or act definitely re- ferred to by a court or executive officer by the number of the section of the Revised Statutes or the volume and page of the Statutes at Large in which the Congressional enactment is found. It may be observed that the legal propositions stated are not always pertinent to the particular section or act under which they are classed and of which they purport to give a construction. The arrangement, however, is not an arbitrary one, but is so made for the reason that the courts or officers in the construction of a particular section or act definitely referred to by number or volume and page incorporated in the decision matter not strictly pertinent to the par- ticular section or act so designated. This statement applies especially to the interpretations placed on the sections of the Revised Statutes. The decisions abstracted for the purpose of this work are those of the United States Supreme Court, 234 volumes; the various Federal courts, 214 volumes; the decisions of the Department of the Interior

Jan 1, 1915

By Charles L. Kimbell

In 1988, the aggregate value of total world international export trade in mineral commodities was estimated at nearly $542 billion in current (1988) dollars, which was about 8.6% above the 1987 level, but still 23.7% below the record high set in 1980. Comparable comprehensive data for 1989 were not available in time for inclusion in this chapter, but 1989 returns for developed market economy countries only were 1 1.8% above those for 1988. These countries accounted for about 50% of the total mineral commodity export trade in 1988. It would be unsound to utilize the overall 11.8% growth rate for mineral commodity export trade for these countries to extrapolate the growth in total world mineral commodity trade because these developed market economy countries account for substantially different shares of the five major mineral commodity groups listed in table 2. Specifically, developed market economy countries in 1988 accounted for 56% of world export of ore, concentrate, and scrap, 74.7% of world exports of iron and steel, 71.7% of world exports of nonferrous metals, and 57.8% of all exports of crude nonmetals, but only 26.6% of world exports of mineral fuels. Moreover, even within each of these groups, the actual product mix included in developed market economy country aggregates differ from that in developing market economy country aggregates and in centrally planned economy country aggregates. Nonetheless, an increase of 9% to 12% in the value of world mineral commodity export trade seems indicated by available returns.

Jan 1, 1992

[ ]

Jan 1, 2011

By Alan G. Mayton

Exposure to whole-body vibration (WBV) and the postural requirements of the job have been identified as important risk factors in the development of musculoskeletal disorders of the back among workers exposed to a vibratory environment. This paper focuses on preliminary results of WBV data collected for two groups of haulage trucks ? four older trucks from manufacturer A (MFR-A) and two newer trucks from manufacturer B (MFR-B). All of the trucks and their respective seats were considered to be in good working order during the study. Measurement periods for the truck groups had similarities, but varied from 2 to 58 minutes. Sampling times for the older trucks included a mean of 19.5 minutes and a standard deviation (STD) of 6.5 minutes compared to a mean of 40.8 minutes and a STD of 12.1 minutes for the newer trucks. Data collection coincided with the approximate delivery and first operation of the new trucks, and occurred approximately 12 months apart under similar weather and road conditions, and with the same drivers except an additional driver was included with the older trucks. Truck routes were somewhat different in that quarry production had changed location in the time between data collection activities. Overall, the results suggest that the newer trucks may provide better overall isolation to drivers/operators from WBV exposure compared to the older trucks operating at the quarry; although, this will need to be confirmed with additional measurements. Considering the higher variability and shorter sampling times for the older trucks, the results should be viewed with caution. For two of seven trials, the older trucks showed that seats amplified vibration, i.e., a transmissibility (T) >1.0. Seat T for the older trucks ranged from 0.31 to 1.17 with a mean of 0.77 and STD of 0.32. This contrasted with the newer haulage trucks where seats amplified vibration in 3 of 8 trials. In this case, T did not vary greatly and ranged from 0.87 to 1.05 with a mean of 0.97 and STD of 0.07. Regarding older trucks, in five of seven trials, the seat (output) data of weighted root-mean square (RMS) acceleration (wRMSZ) for the dominant z-axis exceeded the action level of 0.5 m/s2 action level recommended by the European Union Good Practice Guide for WBV (EUGPG) and levels exceeded the recommended exposure limit of 1.15 m/s2 in two of the seven trials. The wRMSZ values for the older trucks varied from 0.41 to 1.83 m/s2 with a mean of 0.99 and STD of 0.57. Similarly, newer trucks indicated a narrower range of wRMSZ from 0.38 to 0.95 m/s2. The mean wRMSZ was lower for the newer trucks at 0.58 m/s2 with a STD of 0.23 m/s2. Similarly, newer trucks indicated wRMSZ reached or exceeded the action level in four of eight trials. None of the trials with the new trucks showed wRMSZ levels that reached or exceeded the recommended 1.15 m/s2 exposure limit. As an indicator of driver/operator discomfort, overall weighted total RMS acceleration (vector sum) values seem to show a ?rougher? ride for the older trucks. The vector sum values for these trucks ranged widely from 0.70 to 2.59 m/s2 and, in four of seven trials, showed levels greater than 1.40 m/s2. The mean vector sum was 1.44 m/s2 with a STD of 0.75 m/s2. Comparatively, the newer trucks exhibited less variation with a range from 0.69 to 1.59 m/s2. The mean vector sum was 1.02 m/s2 with a STD of 0.35 m/s2. Vibration dose values for the dominant z-axis (VDVZ), gave a sense of vehicle jarring/jolting conditions. All trials with the older trucks were within the recommended EUGPG action level of 9.1 m/s1.75. On the other hand, in three of eight trials, both newer trucks exceeded this action level with values of 9.18, 12.58, and 13.21 m/s1.75. Neither truck group showed VDVZ that exceeded the exposure limit of 21 m/s1.75. A statistical analysis was not conducted, since the differences reported between truck groups may not be statistically significant owing to the relatively small sample size. Road conditions, changes in the truck routes, and driver/operator differences (e.g., stopping and turning) are possible factors in the higher VDV for the newer trucks.

Jan 1, 2008

By V. F. Parry

[Approximatel~r 7-1/2 illion tOlls of subb1tnminous coals are mined an-nuall in Colorado, Wyo~ing, and Montana, of which 50 percent probably reaches dome ,-tic conswno:os. r:L'he moi s t'_re of the se subbi t1.Uninous coal sis high, averae;:t.:ug about 25 :!,)ercent \-Then they are :nined. T'ne coals are non-caking d ~~ack to a vari ble degree when exposed to nornal atmospheric conditions. ~hey a~e gpod domestic fuels, are considered to be smokeless in most furn~ces, and have been used. f, r f!1an: y ars in hand-fired domestic furnaces in hich tnc practice i~ to e~ploy large lureps for efficient com-]

Jan 1, 1941

By Wm. W. Adell

"These hydrocarbons belonging to the same chemical series as methane, having the general formula CnH2n have many chemical properties in common with methane and their addition to a lean gas charges the properties and burning characteristics of the gas in the same general direction although to a different extent. The hydrocarbons of this series do not readily enter into chemical reaction with other substances and therefore are incapable of combining with oxygen or polymerizing in the disturbing system and thus cannot cause gum and room troubles commonly met with in the distribution of manufactured gas.As the number of carbon atoms in the molecule increases, i.e. in proceeding from methane throughout the series, the oxygen requirements for the complete combustion of unit volume of the gases also increases; in other words, the calorific values of these hydrocarbons (as gases) increases from methane. Similarly the specific gravity increases from methane in the same order. In Table 1 are shown some of the physical constants and properties of a few of these hydrocarbons which hive bearing on their use for enriching gas."

Nov 1, 1927

By K. H. Johnston

This guide was written to furnish the coal industry with a description of techniques, instruments, and clues on how to find abandoned oil and gas wells that have penetrated coal seams. The report includes specific information on searching techniques currently in use by several coal mining companies, gas-transmission companies, and waterflood operators, as well as information on State agencies responsible for the enforcement of laws and the preservation and distribution of data pertaining to the drilling, development, and abandonment of oil and gas wells. Comparative tests were performed with several commercial electronic metal detectors to determine the feasibility of using them to aid in the search for abandoned wells and to determine the instrument most suited for that particular use. The role of methane detectors to locate abandoned wells is described, including a case history. Tests were made to develop an efficient procedure to follow in systematically searching an area for metallic clues or hydrocarbon evidence to abandoned wells. The guide describes, in detail, a search sequence, including the collection of basic data, preparation of the selected area, and the physical search. Methods are given for evaluating the results.

Jan 1, 1973

By C. R. Carpenter

A dynamic gas-mixing system assembled by the Bureau of Mines for the generation of precise gas mixtures from sources of concentrated or pure gases and diluent gases is described. A set of electronic mass flow controllers with maximum flows ranging from 10 to 5,000 ml/min, a so-called Pure Air Generator, and gases in cylinders are used to generate differing gas concentrations. The repeatability of the delivery rate of a flow controller, measured on different days, has a precision of 0.3 pct of the setting. This dynamic gas-mixing system reduces the cylinder inventory and the demurrage charges for special gas mixtures. Gas mixtures that cannot be shipped commercially, such as flammable mixtures of methane in air, can be conveniently prepared by this system. The maximum dilution ratio is 2.5 x 104. Thus, gas mixtures can be made over a wide range of concentrations, from the percent region (by dilution of a pure single-component gas) to fractional parts per million (by dilution of a premixed standard, e.g., a 1,000-ppm mixture). This system is especially useful in determining the response of gas detection devices over the entire range of their measurement. Because the controllers are voltage controlled they lend themselves easily to automated control using computer-based systems.

Jan 1, 1983

By D. Harrington

The mining industry of the United States has for many years possessed the dubious aistinction of having the poorest accident rate of all of the major lines of industrial endeavor in this country, and until recently there ras little or nothing to show that any material improvement might be expected. However, there are now numerous trends indicating that the corner has ceen turned at last, and it is strongly hoped that the mining industry is likely to follow the railroads, the cement and other industries in operating with occurrence of only a reasonable amount of loss of life and limb through accidents. The complete accident figures for metal and nonmetallic mineral mining for 1931 are not yet available, but fragmentary data shor that 1831 vill un- questionably have very low accident rates, probably the lowest in the history of our metal mines. One underground metal mine has produced over 14,000,000 tons of copper ore rithout a fatality; another metal mining company with an electric slovel operation has handled upwards of 75,000,000 tons of material, copper ore and waste, without the occurrence of a fatality; an iron-ore compan, which orns six mines (three underground, three open pit), has operated every one for a year or more without a lost-time accident with a con- siderable number of employees and a large production; and alot.er iron-ore producer with 30 mines and about 3,000 employees as an average of nearly 10 months of operation in 1931 without a lost-time accident. umerous other wonderful safety records of metal mines in 1931 indicate unmistaimbly tat the record of the noncoal mining industry of the United States as a role in 1931 will undoubtedly be found to be excellent. According to the latest relatively complete figures (those of 1930) available for the coal industry, fewer than 650,000 persons are employed in and around the coal mines of the United States, the figures indicating at a little over 493,000 people are engaged in bituminous mining and a little under 151,CCO in anthracite mining. Bureau of Mines complete figures suc that 2,053 persons were killed and 103,821 non-fatally injured in our coal

Dec 1, 1932

By L. F. Willmott

The Bureau of Nines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipe- line for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By Charles G. Howard

Accidents involving underground rail transport were analyzed to quantify the magnitude and the operational requirements for individual mine car braking systems. The results showed that the brake preventable accidents represent only 2% of the total underground fatal accidents and less than 1% of the total underground nonfatal accidents. In addition, the brake preventable accidents are expected to decline over the next decade. The costs of accidents involving deaths and Injuries were determined using various well accepted methods. The costs of a brake retrofit program for all operating underground coal cars were developed separately for small and large coal mines. Costs of retrofit brakes, new car brakes, maintenance, inspection and repair facilities were included in the esimates. The analysis showed that a retrofit program would not significantly increase safety, and that the program cost would greatly exceed the corresponding expected benefits.

Jan 1, 1979

After a stagnant performance in 1982, gross national product (GNP), industrial production, and employment increased during 1983 in nearly all industrial nations, with the U.S. performance generally leading the uneven worldwide recovery. Real U.S. GNP increased 3.3 percent in 1983 (table I). Although investment in nonresidential structures declined, total nonresidential fixed investment in the United States was up 1.5 percent following a 1982 decrease. The increase in worldwide industrial activity and demand in 1983 put greater pressure on prices in many countries. Prices increased from less than 3 percent in the Federal Republic of Germany, Japan, the Nether-lands, and Switzerland to as much as 10 percent in nearly all the other Organization for Economic Cooperation and Development nations. The annual inflation rate in the United States was 4.3 percent (based on the GNP fixed-weight price index).

Jan 1, 1984