Search Documents

By Kenneth R. Sites

Under this program two tape recording and triggering systems were developed and delivered for use in the Bureau of Mines microseismic program. The systems are designed to improve the effectiveness of the Bureau owned Sangamo 3500 series and SABRE VI instrumentation tape recorders. The system is designed to capture random microseismic data, digitize and temporarily store these data, start the tape recorder; and then transfer the data to magnetic tape for permanent storage. The system is designed to pack data on tape such that the tape may be simply played back through galvo drivers onto an oscillograph such that a continuous series of analog records, with corresponding time of day information, are reproduced without excessive oscillograph paper waste or the need for the operator to search for valid events.

Jan 1, 1980

By Richard Rittenhouse

This program was to develop a new base line system for automated continuous room and pillar type mining. The primary requirement estab¬lished for this machine is that the machine be capable of mining and bolting simultaneously. Additionally, this machine was to provide temporary and permanent roof control, have a productive - full - face semi-automatic mining system, leave a clean entry outby the machine, provide maximum operator protection, provide effective dust suppression and provide air scrubbing to restrict respirable dust to permissible levels. The machine has effectively demonstrated the ability to mine and bolt simultaneously. Additional above ground operation, testing, and time studies are recommended to further verify the machines abilities. Design improvements are recommended for future generation AES machines. These relate to marginal design areas such as side loading on vent duct lift cylinders, etc., that will not impair additional testing of the existing machine.

Jan 1, 1983

By James R. Aggson

This Bureau of Mines report describes floor heave ground control problems that have been encountered in a new underground coal mine in West Virginia. Previous experience in the coal seam, the results of physical property investigations, and in situ rock stress determinations are discussed. The apparent cause of the ground control problems is the existence of a high, biaxial, horizontal stress field coupled with a floor member that has time-dependent deformation characteristics, A theoretical analysis of the failure process is developed. The analysis is assisted by finite element techniques. Mine design recommendations based on this analysis are presented.

Jan 1, 1978

By P. B. Grote

The report is concerned with the issue of the possible transfer of U.S. and other developed country deep ocean mining (DOM) technologies to developing countries. This subject is one of several major issues in current UN Law of the Seas negotiations. As background to the subject, the report provides a detailed critique of the various terms and conditions pertaining to technology transfer in recent negotiating texts. It also provides a description of the relevant DOM technology, sources of innovation, and methods of proprietary protection. Functional requirements for viable technology transfer are developed and used as a basis for the definition of alternative levels of programs and implementation approaches, including required changes in the negotiating text. The consequences of these technology transfer options on the various parties are investigated.

Jan 1, 1978

By N. H. Snyder

THE Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the com-position as shown by proximate analyses. To these, when required, are added the fusing temperature of ash, Hardgrove grindability index, and the free-swelling index. Under most of these specification contracts the bidders guarantee the quality of coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 4 issued by the Bureau; the samples are analyzed in the Bureau's laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of delivered coal and "tipple" samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) are valuable data for use in evaluating future bids. Moreover, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1953

By B. V. Johnson

The Federal Bureau of Mines has conducted research in support of the National Aeronautical and Space Administration's (NASA) Apollo program to acquire fundamental scientific and engineering knowledge of lunar-mineral resources for NASA's Office of Advanced Research and Technology. Equipment and techniques were developed to conduct soil shear tests in a simulated lunar environment. Shear tests performed with this equipment in ultrahigh vacuum and controlled laboratory atmosphere showed that simulated lunar soil increased in strength in the simulated lunar environment.

Jan 1, 1973

By D. Ng

A facility to evaluate the fire endurance of mine stoppings was constructed by the Bureau of Mines in the multiple entry section of the Bruceton (PA) Experimental Mine. Stoppings up to 6 by 18 ft can be tested in a manner simulating mine conditions. The stopping is subjected to a 70-min liquid fuel tray fire with an energy output of 75,000 Btu/min. The stopping and adjacent areas are instrumented with thermocouples and heat flux gauges. Data acquisition is by an automatic data logger capable of continuously recording over 100 channels of information. Two 8-in-thick concrete block stoppings and a galvanized steel stopping were tested. A crack developed on the fire side surface of the block stoppings where the flames were most intense. However, the temperatures of the unexposed surfaces of the stoppings never exceeded 800 C and the surfaces were undamaged. The steel stopping retained its structural integrity during the test. The temperature of the unexposed steel surface reached 5000 C, but combustible materials located 1 ft from the surface did not ignite. A 3/4-in-thick coating of construction plaster was applied to the fire side of the previously tested uncoated steel stopping. The quantity of heat energy transmitted across this coated metal stopping was reduced approximately 50%. All stoppings prevented the passage of flame and smoke.

Jan 1, 1988

By William J. Campbell

Expansion measurements of platinum, added as an internal standard, are used for thermal calibration of X-ray cameras and diffractometers. Accuracy of the temperatures derived by this technique depends on the precision of expansion measurements and the reliability of reference expansion data. Temperature measurements to ± 1° C. require ?d or ?a to be determined within ± 0.001 percent. Selected expansion data are concluded to be reliable to 2° C., 5° C., and 25° C., over the temperature ranges 0° C. to 700° C., 700° C. to 1,000° C., and 1,000° C. to 1,700° C., respectively. Tabular expansion values from 25° C. to 1,700° C. in 2° C. intervals were calculated from the following equation; Expansion, percent = [8.91 + 1.28 x 10-3(t-25) + 0.04 x 10-6(t-25) ] [t-25.104 ] These tabular values facilitate future corrections of published temperatures as more reliable expansion-temperature data become available.

Jan 1, 1962

By Henry Kreisinger, J. F. Barkley

This book is one of a series of publications being issued by the Bureau of Mines for the purpose of disseminating information in regard to the methods by which the fuels in this' country may be used most efficiently. A knowledge of the temperature of the gases in boiler settings and in other commercial apparatus using heat tends to develop improved designs of apparatus and better methods of operation, thus reducing waste of fuel. The following pages present, for the benefit of those designing, operating, and testing such apparatus, information as to the accuracy of temperature measurements made under certain conditions and the corrections that can be safely applied.

Jan 1, 1918

By W. J. Fene

A comprehensive study of all bituminous coal-mine fatalities occurring in Pennsyl¬ vania during the 5-year period, 1926-1930, was made to try to determine the factors that in¬ fluence accidents which cause these fatalities. During this study some two thousand reports of fatalities were reviewed, and pertinent information as to causes and influencing factors were tabulated therefrom. These tabulations are discussed in detail, and in some instances recommendations are made with a view to reducing the hazards in certain classes of these accidents.

Sep 1, 1931

By Richard P. Cislo

The evaluation of the effectiveness of the time domain Coal Interface Detector developed by the General Electric Company under contract H0155120 is the subject of this report. The sensor utilizes differences in the time characteristics of shearer vibrations as sensed by an accelerometer mounted on the ranging arm to discriminate the cutting of coal and rock. Pour identical time domain sensors were supplied by the Bureau for field evaluation. The performance of the time domain sensor was evaluated by an extensive field test and data collection program that included four longwall mines and a total of nine mine visits. The intent was to determine the sensor's applicability to a wide range of mining conditions and to document its limitations. Results of the extensive field tests indicate that shearer vibration data processed by GE's time domain signal processing algorithm cannot be used to reliably detect when the cutting drum crossed the coal/rock interface.

Jan 1, 1987

This report summarizes a study conducted by The Service Bureau Corporation for the Bureau of Mines. Evaluations reflected herein are the result of an independent investigation by The Service Bureau Corporation of methane considerations during coal mining. The study is oriented toward a systematic analysis of methane control problems during coal mining. Throughout this study an attempt has been made to ensure considerations consistent with the recently enacted Federal Coal Mine Health and Safety Act of 1969. References to reports by The Bureau of Mines and others are made for the purposes of establishing identification between the evaluations contained in this report and on-going research efforts.

Jan 1, 1970

By Michael Rieber

Commodity transportation by barge is possible on about 25,000 miles of navigable inland waterways in the contiguous 48 states. Barge operations are used chiefly for the movement of bulk raw materials ranging from farm products to iron ore, coal, and other bulky semi-finished as well as finished products such as steel, chemicals and petroleum [3,p.7-9]. The barge industry, unlike other transportation industries, is largely unregulated. This is because all liquid bulk commodities most dry bulk commodities transported by for-hire carriers and companies engaged in private transportation of their own commodities are exempted from Interstate Commerce Commission regulations. As a result, about 15 percent of the total ton-miles of barge traffic each year is under Interstate Commerce Commission regulation [13,p.14-25].

Jan 1, 1977

This study was conducted to determine the feasibility of using large tractor dozers in land reclamation of strip-mined areas. The procedures used are patterned after engineering models developed for evaluation of military ground vehicles in cross-country operations. Tractor dozer manufacturers furnished information on capabilities of existing equipment and ideas on the practicability of using dozers larger than those currently available Generally, they believe that current dozers in the 500? to 700-horsepower range are about as large as can be built and remain economically feasible. However, one manufacturer has a wheeled dozer rated at 1200 horsepower, and another is testing a tracked dozer of about the same horse-power.

Jan 1, 1975

By William A. Hustrulid

An overall summary and the individual reports of eight workshops to determine research and development needs in western mining ore presented. Problem areas are identified, and recommendations regarding priorities, funding sources, and prime movers are made. The objective of this contract was to identify research and development needs for advancing mining technology as well as health and safety measures for western U.S. Surface and underground mining. This was accomplished by convening a series of workshops where problems could be thrashed out by producers of trona, uranium, open pit copper, underground salt (from the Midwest and New York), underground metal and nonmetal, etc. In addition to problems, future priorities, funding, and the desicion as to who should be the prime mover on R & D were discussed.

Jan 1, 1976

By Chas. F. Jackson

This paper is one of a series dealing with special mining problems and forming part of a general study of mining, methods and costs being conducted under direction of the Bureau of Mines. A considerable part of the material assembled and discussed in this paper has been gathered from articles on individual mines written by consulting engineers to the bureau who are engaged in active mine operation at the properties described, while other data have been taken from the technical press or gathered from personal observations. OBJECT AND SCOPE OF PAPER C. F. Jackson4 ha[-] pointed out that underground transportation (tramming, haulage, and hoisting) absorbs an appreciable percentage of the total underground cost of most mines, averaging for different methods of mining 12.9 to 28.4 per cent of the total underground cost. In general the percentage of cost accounted for by transportation was shown to be highest for the low-cost mining methods.

Jan 1, 1931

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) The system design of hydrostatic drives for mine hoists, usually of special nature, is considered along with oil hydraulic component selection suitable for the application; (b) The criteria for head frames of steel and/or concrete are developed with full consideration of all operating and environmental conditions.

Jan 1, 1988

By L. M. Irwin

This Bureau of Mines investigation relates the physical properties of copper reverberatory furnace slags to changes in composition, The smelting of upper Michigan copper ore presents some problems that probably differ from those of other copper smelting areas. The study of these problems has, however, provided important data regarding slags in general and therefore will be of value to other operations as well. Conclusions reached from this study were: (1) Slag fluidity and refractive indices varied directly with the iron content and inversely with silica, lime, and alumina, and (2) there was no apparent correlation between slag fluidity and its copper content.

Jan 1, 1962

By H. H. Fields

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot-deep vertical borehole¬. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmos¬phere, the total gas and water flows and the in situ pressure dropped, respec¬tively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the correspond¬ing values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

By F. S. Karn

Conditions necessary to obtain optimum yield of useful products when coal is rapidly heated to extreme temperatures by laser irradiation were determined by the Bureau of Mines. Product distribution and yield were investigated as functions of several variables. Low-rank coals with high-volatile matter gave highest total gas yields. Medium-rank coals gave the highest yields of H2 and CA and low-rank coals gave highest yields of CO and C02. Macerals gave gases of approximately the same composition, but the total gas yield increased in the order fusinite, micrinite, vitrinite, and exinite. Total gas and C2H2 yields varied inversely with particle size. The addition of nominally inert gases such as Ar, He, N2 increased yields of H2, C2H2, and total gas. Metals such as nickel and platinum had little influence on the rate of coal decomposition. Total gas yield increased with total energy of irradiation, and the ratio of C2H2-CH4 increased with concentration of energy. A study was also made of the irradiation temperature, and a material balance was calculated.

Jan 1, 1970