Search Documents

By Charles Zdazinsky

Back-break induced from blasting is a concern in open pit metal mining because it compromises the conditions of the pit’s final walls. Final walls that have excessive blast induced damage commonly require extra attention and can often lead to increased cycle times. Most importantly however, the safety conditions of a back-broken region can be significantly compromised and it must be addressed to prevent injury and/or damage to equipment. This occasionally results in the necessity to alter mine plans to prevent an incident from occurring in a back-broken region which can be costly to the mine.

Jan 1, 2014

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By Deepankar Das, Gulshan Kumar Sadhwani, Jyoti Prakash Sahoo

Sindesar Khurd Mine (SKM), the largest underground mine in the Hindustan Zinc Limited portfolio, is located approximately 60 kilometers (37 miles) north of Udaipur. In the 2018 financial year SKM achieved an annual ore production of 4.5 Mt (4.42 million LT) and mined metal production of 247 kt (243,099 LT).

Jan 1, 2019

By James Goldberg, Sally Zadra, Wiliam Reisz

Early recognition and risk assessment is critical to sustaining a safe and productive blasting operation. While every blasting environment holds inherent risk, highwall blasting in highly congested areas such as Hanson Material Service Corporation’s Romeoville and Thornton quarries in the greater south Chicago metropolitan area can be particularly perilous

Jan 1, 2008

By Charles L. Greening

MARTIN MARIETTA CEMENT at Martinsburg, West Virginia, has been and presently is engaged in coupling present open pit with old underground workings. Various drilling and blasting techniques have been introduced in an endeavor to achieve optimum results. This paper will relate to three roof shots at Martinsburg, one of which realized a controlled blast of 248,000 tons of material.

Jan 1, 1982

By W. J. Birch, R. Farnfield, G. D. Rangel-Sharp

It is widely recognised that complaints from members of the public relating to blasting operations are related to both ground vibration and air overpressure. It is also known that a complaint is more likely to be generated if the person is inside of a structure at the time of the blast. Reports relating to such complaints often refer to ‘noise’ inside the structure with terms like ‘rattling’ commonly being employed. Such acoustic response is widely perceived within the blasting industry to be directly related to high levels of air overpressure although there appears to have been very little research carried out specifically related to this effect.

Jan 1, 2007

By Yves Lizotte, Malcom Scoble, Sanu Hanspal

"This paper reviews the physical, chemical and mechanical components of what is considered to be the anatomy of a blast muckpile. These relate principally to geometry, floor, fragment size and shapedistribution, density, hydrology, weathering, and diggabiity characteristics."

Jan 1, 1995

By W. Reisz

The fear of heights is a natural defense against performing a dangerous and unnatural act such as standing on the edge of a hundred foot wall. Yet through familiarity, a casual attitude often exists. Those of us, who work near highwalls on a daily basis, may become overly comfortable in our surroundings, losing sight of the disaster which may often rest a single misstep away. And this is where the hidden dangers lie.

Jan 1, 2009

By Carlos Pañura, Michael Geldres, Alejandro Rojas

In this current era of production in large volumes of surface mining, which demands the realization of large-scale blasting, the mining industry must deal with the impact of the vibrations generated by the detonations that are carried out daily in the mines. In this context, the need arises to minimize and control the impact produced by vibrations by determining the interference times of each generated vibration waveform. The vibration waves are produced by the detonation of the explosive charges of each blasthole, analyzing the vibration waves produced by each blasthole, allow us to determine the optimal time between the detonation of each blasthole to reduce the vibrations of the production shot. Once the optimal time is found, it is possible also, to predict the vibration of the production shot (considering times and sequences) using predictive models. The waveform recorded includes information regarding the particle velocity and the dominant frequencies of the vibration. To determine the time between holes, a graph was constructed with the values of the vector Sum VPP (m / s) vs Time between blastholes (s), once the time between blastholes “t” was found, the simulation of the output sequences continued in such a way that, by adding the single waves generated by the blasthole, it gave us a record of vibrations with the lowest level of vibrations.

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The Dynamics Effects Laboratory at the University of Maryland conducted a series of very small scale tests to measure the impulse delivered to a plate by the detonation of an explosive charge which was buried in saturated sand. These tests were conducted to support a full scale tests series being supported by the Navy (NSWC Indian Head Division) to learn more about loads applied to structures by explosive detonation. For each of the tests being predicted, a series of three tests were conducted at Maryland, one with a 0.203 gm charge, one with a .609 gm charge, and one with a 3.3 gm charge. A high speed digital camera (500 frames per second) was used to record the displacement of the plate as a function of time. From this the initial velocity of the plate was determined and then the impulse delivered to the plate by the explosive. A best fit line through the data was determined for the three model tests conducted and this equation was used to extrapolate the predicted impulse for the full scale tests.

Jan 1, 2005

By David Nemir, Jan Beck

A challenge in materials science is the production of a bulk solid material from a powder precursor. One solution is to use shockwave consolidation whereby a ductile tube is loaded with the powder of interest and then surrounded by an explosive. A detonator at the top of the explosive column initiates a symmetrical high-pressure pulse that moves inward and down the tube, causing the tube to deform and the interior powders to consolidate into a dense, well bonded bulk material.

Jan 1, 2016

By K Lombardo

Numerous small- and intermediate-size cratering experiments have been conducted in Piceance Creek Basin oil shale at the Colony and Anvil Points oil shale mines near Rifle, Colorado. The purpose of these experiments was to evaluate scaling as a tool to infer the behavior of large-scale tests from small-scale experiments, to calibrate the hydrodynamic computer codes used to model explosive fragmentation of oil shale, and to investigate the influence of bedding plane orientation, natural joints, fractures, and the grade of oil shale on rock fragmentation.

Jan 1, 1983

By Ruilin Yang

This paper presents a fragmentation model for large production blasts. The model uses peak particle velocity (PPV) induced from the blast as a controlling parameter to predict the fragmentation size distribution. The PPV can be related to shock pressure or strain under a given rock condition. The fragmentation size is calculated at three-dimensional grid points within the blast volume. The grid size defines the calculation resolution of the model. The fragment size distribution is assumed to be in the same form as the crack distribution within a cube (of the size equals to the grid size) surrounding a grid point. The crack distribution in rock from impact is based on the finding from previous researchers (Seaman et al., 1976). The fines and oversized blocks are calculated explicitly. The summation of the size distribution at all calculation grid points over a specified volume of the blast yields an overall size distribution for the volume.

Jan 1, 2015

By Corry Goumans

The job location is at Bear Lake Hydro Project located north of the town of Sechelt, British Columbia, Canada

Jan 1, 2013

By Thomas H. Kleine, Alan R. Cameron, William W. Forsyth

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By P D. Katsabanis, K Steeves, D Dombrowski

Accurate electronic detonators with firing time accuracy within 100 microseconds of the nominal have been used to control blast results in terms of fragmentation, vibrations and wall control. Axisymmetric experiments and experiments utilizing small benches have been conducted in order to calibrate a numerical model under development and examine the influence of delay interval on wall control, fragmentation and vibrations. The results obtained so far indicate definite advantages of precise timing in reducing back break and wall damage. Fragmentation is affected by the delay interval and high speed film observations and measurements indicate that the delay interval should allow the damage zone from each blasthole to be fully established prior to the detonation of the next borehole. Studies on vibration control demonstrated that vibration synthesis work using signature shots can only be of use if accurate delays are employed.

Jan 1, 1995

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

The breakage mechnism of a spherical charge greatly differs from that of the cylindrical charge used in underground mining. The advantages of the spherical charge could not be utilized until INCO Metals Company, Ontario Division, introduced large diameter holes to their operation.

Jan 1, 1978

By Lex L. Udy

External detonation generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall.

Jan 1, 1977

By Dave Harrison, Phyllis Hasser, Ken Eltschlager

The beginning There was the video:– “Understanding Vibrations from Blasting” – 2002 to 2004 in development – Dale Ramsey ad hoc Public Education committee chair – Available At the ISEE bookstore Public Education and Public Relations Committee • Standing ISEE committee 2004 • Co-Chairs – Ken Eltschlager, Dave Harrison • Purpose: "Develop and conduct programs on public education and public relations. Public education programs will focus on public awareness, understanding, and appreciation of the explosives industry. Public relations programs will concentrate on providing blasting professionals with the tools to assist in the public's understanding of the explosive industry and in the appropriate ways to respond to local community issues."

Jan 1, 2007