Search Documents

By S K. Mandal, S Dasgupta

"Damage is classifi ed as loss in the integrity or deterioration in the quality of rock massand is infl uenced by methodology of excavation on the geo-technical properties of rockmass. Overbreak, on the other hand, is the result of damage and is quantifi ed in either of the terms viz., extra mucking, shot-creting, application of extra support system and extension of scheduled completion time. Damage or overbreak in rock mass by the impact of blasting, is generally unavoidable but, the magnitude can be minimized so that it does not deteriorate the quality or integrity of structure. The paper, here, analyses magnitude of overbreak of a powerhouse cavern with respect to different blast patterns implemented at the site. The magnitude of overbreak was analyzed in terms of profi le measurement with the help of laser profi ler and percentage of halfcast markings observed on the periphery rock wall. The paper revealed the impact of decoupling ratio, blast pattern and geometry of blasting patch on the magnitude of overbreak. The authors observed that presence of un-favourable joint pattern or foliation plane along the periphery rock wall couldn’t contain magnitude of overbreak within allowable limit. The analyses revealed that percentage of half-cast markings on periphery rock wall was infl uenced by response of rock towards detonation of explosive and cannot be a single parameter to assess the effectiveness of a blast. The analyses also revealed that magnitude of overbreak for down-stream wall was more than that observed in up-stream wall."

Jan 1, 2008

By Christodoulos Xiouris, Ali Reza, James Karnesky

A rocket parachute signal flare is often used to signal a maritime emergency. In the general operation of these devices, a solid rocket motor propels a metal body to an altitude of approximately 1000 ft(305m).At the end of the rocket motor, a propelling charge drives a signal flare and parachute out of the metal body and ignites the flare, which then burns for approximately 40 seconds as it falls to earth. In this paper, we describe an engineering investigation of an accidental ignition of a rocket parachute signal flare, which caused injury to the user. The components of the flare involved in the accident were inspected via x-ray and microscopic imaging techniques, and compared with those of unfired flares recovered from the same vessel. Chemical analysis of residue on recovered components from the accident flare was also performed. These comparisons were used to determine the likelihood that the actuation mechanism had been deliberately manipulated. In the subject model of the flare, ignition of the rocket motor is accomplished through a percussion cap which is struck by a firing pin. Prior to activation, the firing pin holds down a pre-compressed spring. We present a comparison of the ignition system of the incident flare with those of other rocket parachute flares, which do not incorporate any stored mechanical energy.

By Brian Stump, D. Craig Pearson

This work quantifies seismic coupling as a function of charge weight for single-fired (simultaneously detonated) explosions observed in the mine and at regional distances. These single-fired explosions are contrasted to standard production shots from the same mine. Production shots include cast blasts to remove overburden and coal shots for fragmentation. The blasts were conducted in a mine in NE Wyoming. The data sets consist of measurements in the mine (100-10,000 m) and at regional distance (360 km) using a seismic array near Pinedale, Wyoming (PDAR). The single-fired explosions ranged in designed size from 5,500 to 50,000 lbs. Peak amplitudes measured at a single element of the regional array are modeled by a power law relation dependent on explosive weight. Scaling constants were determined for each of the dominant regional phases: b(Pn) = 0.84±0.14; b(Pg) = 0.84±0.09; b(Lg) = 0.91±.08. Spectral ratios of observations from different explosions observed at the same station illustrate the frequency dependnce of the source scaling relations. Spectral ratios of in-mine observations are consistent with those of regional data. The observed single-fired ratios are well replicated by Mueller-Murphy source model ratios. The data and model illustrate both the increase in long-period spectral level and the accompanying decrease in source corner frequency with increasing charge weight. The coal and cast blasts that make up the production shots ranged in size from 77,000 to 4,738,230 lbs. The peak amplitude (1-20 Hz) for the largest delay-fired production shot (4,738,230 lbs.) is comparable to that of the largest single-fired explosion (50,000 lbs.). This comparison can be explained in terms of destructive interference between waveforms from individual boreholes introduced by delay firing. Shot specific models of delay firing suggest that peak amplitudes in this same frequency band for the production shots are insensitive to the total amount of explosives in the blast. Peak amplitude data at regional distances supports his modeling result.

Jan 1, 2002

By David Kosnik

This paper describes the technology and methods deployed in the continuous autonomous remote monitoring of cracks in interior and exterior walls of a residence near a limestone quarry. The objective is to quantitatively compare crack response due to blast-induced ground motion to that induced by diurnal temperature changes, weather fronts, occupant activity, and other phenomena. The remote monitoring and communication technology developed to obtain and disseminate crack response data for this study may provide the means to mitigate the effect of public concerns about potential impacts of ground vibrations inherent in construction and production of raw materials; it is critical to address these concerns because subsequent litigation may result in delays and increased costs.

Jan 1, 2009

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008

By Paul Schmiesing, Matt Higgins

Central Oregon is a fast growing resort community centered in Bend, Oregon. Bend is bordered by the Cascade Mountains to the west and the high dessert to the east. Central Oregon is blanketed with lava rock with little topsoil. Ditch blasting is a staple in the area. Almost all utilities excavation (gas lines, sewer lines, water lines, and electrical lines) requires blasting. There is also a considerable amount of blasting required for site excavations and drywells. On average, there are over 500 blasts per year in Bend alone. All of this blasting is done using small holes, generally 2.5 inches in diameter. Typical ditches will have 200 holes, between 2-3 rows wide, with an average depth of 8 feet, and on 36 inch centers. Almost all shots are dry. Successful blasting requires careful control of drilling and loading. The vesicular basalt contains numerous lava tubes and caves making drilling and loading difficult. The rock conditions vary greatly from one side of town to the other requiring different powder factors and different scale of distances for vibration control. Caret%1 calculations of vibration predictions and use of site-specific seismic info is necessary. Marry shots will require deck loading and careful timing to ensure one-charge per delay. It is an every day occurrence to be blasting near residential and commercial structures or high pressure gas lines. Many times ditch blasting will incorporate excavation blasting. The different hole patterns used for the ditches and the excavation shots presents challenging timing sequences.

Jan 1, 2000

By Catherine Johnson, Kelly Williams

The ability to measure the overpressure of a shock wave is necessary for explosives research such as shockwave focusing and field testing of blast-resistant designs for buildings and vehicles. To record the peak overpressure of the nearly instantaneous pressure rise at the shock front, pressure transducers with a fast response rate and streamline pencil design are needed. Time spent setting up sensors coupled with the expense of high-frequency data acquisition systems, and the inconvenience of low impedance cables can make the process challenging. Additionally, only small inaccuracies in sensor position can drastically change the measurement recorded. Advances in high-speed video imaging make it possible to see the refraction of light due to the high-density gradient at the shock front without the need for parabolic mirrors or additional light sources necessary for Schlieren or shadowgraph imaging. The average shock front velocity between two points can be calculated by dividing the change in position by the elapsed time between the images. Using the Rankine-Hugoniot relationship demonstrated by Swisdak the peak overpressure of the shock wave can be calculated from its velocity eliminating the interference of the gage and mount. This paper investigates the accuracy of this method by setting dual transducer pencil probesat0and180 degrees perpendicular to the central axis of a285-gram(0.63-pound)cylindrical charge to record pressure versus time for comparison to the high-speed video. The axis of the camera lens is aligned with the central axis of the charge with both pencil probes in view. The pencil probes have two pressuretransducersset100millimeters (3.9 inches)apart to measure the time of arrival and are used to validate the velocities calculated from the high-speed images. This method can be used to evaluate the shock wave propagation from more complex prismatic charges with different cross-sectional shapes where precise placement of cumbersome pencil transducers in the near field is almost impossible.

By R Frank Chiappeta, Eduardo Nixon, John Dean Smith, Tom Treleaven

"The creation of the Panama Canal was far more than a vast, unprecedented feat of engineering. It was a profoundly important historic event and a sweeping human drama not unlike that of war. Apart from wars, it represented the largest, most costly single effort ever before mounted anywhere on earth. It held the world's attention over a span of forty years. It affected the lives of tens of thousands of people at every level of society and of virtually every race and nationality. Great reputations were made and destroyed. For numbers of men and women it was the adventure of a lifetime.

Jan 1, 1998

By Thomas F. Mechtenberg, Michael S. Powell

In the past several years many coal operators and stone producers have reduced drilling and blasting cost by utilizing Bulk Emulsion/ANFO blends. For many operators the cost of equipment to handle blend products has been a major consideration in evaluating overall cost effectiveness of changing from packaged products or bulk ANFO to blends. This is especially true when the project length is short term or is uncertain.

Jan 1, 1990

By Calvin Konya, Janos Foldesi

A bridge over a main line railroad system was scheduled for demolition. The bridge was made of reinforced concrete and spanned three mainline railroad tracks which could not be shut down due to blasting or demolition. To further complicate matters, the mainline tracks had high tension power lines running above the tracks, but below the bridge. These high tension wires provided the electricity for electrically powered trains. The tracks could not be damaged or disrupted, nor could the power line be broken.

Jan 1, 1992

By R W. Bellenie, P N. Blakey

The phenomena of post detonation gases in muckpiles is reasonably well known. It causes the 'rumbling' noises occasionally heard after a blast in open pits or quarries and is thought to occur due to initiation of carbon monoxide, hydrogen, etc. by 'hot' spots within the muckpile. The problem usually occurs with highly aluminized products, but can occur with any oxygen deficient product. This phenomenon was never a problem underground due to restriction on access to blast areas, ventilation criteria, etc. until the advent of large diameter blastholes and particularly their use for specialized applications such as drilling for blasting down 'hang-ups' in ore passes.

Jan 1, 1980

By Riaan Van Wyk, Gys Landman

In today’s mining environment the use of radio communications in the form of two-way radios, cellular phones and even automated mining, form a vital part of the daily operations of a mining site. The radio transmissions that are used are a form of energy and as with all other types of energy it can have an influence on blasting equipment.

Jan 1, 2011

By R E. Langston, S M. Gazioglu

A preconstruction inventory program was conducted to determine the existing conditions of residential, non-residential and all other structures within 2,000 feet of the blasting limits for a highway excavation site in Asheville, North Carolina. Prior to major production blasting, eleven test blasts were detonated to establish site specific propagation parameters in order to develop contours of maximum allowable explosive charge weights per delay. The method of scaling distance by the square root of charge weight per delay was utilized in developing the contours of allowable charge weights. The charge weight contours were revised during blasting operations as additional vibration data became available. The effects of blast induced vibrations on a nearby water storage reservoir, a nearby vehicular tunnel and other adjacent residential and non-residential structures were observed and monitored over a period of two years of blasting operations.

Jan 1, 1980

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

Jan 1, 2005

By Conny Sjoberg, Finn Ouchterlony, Bjorn Jonsson

This contribution reports an investigation of the blasting damage in the contour of an access ramp to a Swedish underground laboratory for nuclear waste related studies. Near zone vibration measurements were made for 7 rounds and the results converted to a site specific scaling law. A simple engineering correction for the influence of the charge length wee developed and the resulting equations used to predict the damage zone depths of three different drilling and charging patterns.

Jan 1, 1993

By Philip M. E Thomas

For over sixty years man has struggled to defeat the natural swamp lands known as the Florida Everglades as demand for land to support the burgeoning population growth in the state continued almost unchecked. Over the past ten years there has been a growing awareness that this land development could wipe out a whole ecosystem in a very short time unless steps were taken to reverse the trends. In 1991, a state law called the Marjory Stoneman Douglas Everglades Protection Act was enacted giving power to the South Florida Water Management Board to condemn certain lands for conversion to manmade swamp lands, designed to filter polluting run-off water from the agricultural lands around Lake Ockeechobee.

Jan 1, 1994

By Lawrence Mirabelli, William Hissem, Gary Veltrop

Capital Quarries Company, Inc., Jefferson City MO produces aggregate products for road base, asphalt, concrete and concrete block. With their production quantities small in comparison to those produced by the goliaths of the aggregate industry, they find it necessary to constantly stay on the leading edge of best practices for cost control, process and production improvement to sustain a successful business. In the words of Eric Strope, President, “The safety of our employees is foremost. They all work hard each day. They are focused on keeping our cost to manufacture down. As I see it, we cannot work any harder so we must work smarter!”

Jan 1, 2009

By Abdulkadir Karadogan, Zikri Keti, Umit Ozer, Mehmet Aksoy, Ulku Kalayci

This paper presents an investigation about how the motions of blast induced vibration waves were affected by the presence of the fault planes. This study was carried out at Espey Open- Pit Boron (Colemanite) Mine in Turkey. Within the scope of the study, ground vibration components were measured for 8 shots using 9 vibration monitors, considering the direction of the fault. Measurement stations were located around the fault line that intersects the open-pit mine in the north-south direction and on different benches along the fault plane. Then, the data of the vibration components obtained from the 77 recorded events were analyzed and the results were presented.

Jan 1, 2012

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

BLASPA is the name for a computer code which can assist in the rapid optimisation of blasting procedures in an open-pit mine. BLASPA is based on a mathematical model of the blasting process, a model which has been developing since 1963 as a result of blasting research carried out at the College Militaire Royal de Saint-Jean under sponsorship of the Defence Research Board, and in co-operation with the mining and explosives industry. The model presently includes the following aspects: (1) Geometry, i.e. spacing, burden, bench height, collar, sub-grade drilling; (2) Explosives, i.e. types and grades of explosives, distribution into bottom and top load or decking, size of hole and coupling; (3) Hookup, i.e. parallel or angled firing, delays, location of primers. Computer costs are very small, by comparison with purely spherical AEC codes, so that any number of simulations can be carried out very efficiently. The system has already been used to carry out thousands of simulations for over 40 mines in Canada and abroad. It will be explained how such simulations become a useful guide for a mine's blasting engineer who wishes to optimize his blasting and drilling costs.

Jan 1, 1980