Search Documents

By Carl R. Peterson, Robert G. Lundquist

The development of a remotely-controlled drill and blast excavation system is desirable both because it is potentially more economical than mechanical tunneling in hard rock and for safety. A serious impediment to such development is the problem of relocating and reentering previously drilled blast holes to place the explosives.

Jan 1, 1983

By Pierre Allard, Wilfrid Comeau

Near-field and close-in blasting can be safe and efficient, near engineered structures, if the dynamic reaction of structural members to blasting vibrations are considered. Safe particle velocity criteria can be derived from allowable safe static flexural deflections and critical frequencies. Control of close-in blasting can be accomplished using low-pass filtering of the particle velocity signal at the critical frequency. The CETE Mediterranee laboratory at Aix-en-Provence, France, a branch of the Ministry of Roads and Bridges has -pioneered this approach and successfully applied it to major road cuts and tunnels in built-up areas, as well as a major powerhouse expansion project in Africa. This approach is presently being used for a spillway rehabilitation project in Quebec, Canada. This paper exposes- the theoretical aspects and gives case histories of its use. The SCS-15 an automated, peak reading, data acquisition device is described.

Jan 1, 1991

By Michael J. Sapko, Eric S. Weiss

The U.S. Bureau of Mines has been conducting research on the secondary explosion hazards associated with the mining of oil shale under gassy mine conditions. Explosive incendivity tests have been conducted in a 28 m~3 (1000 ft~3) gallery to evaluate the relative incendivity of experimental emulsion-ANFO blends. The incendivity was measured by determining the minimum inert stemming requirements for preventing the ignition of a methane-air atmosphere by the discharge of hot detonation products from a 5.7 cm (2.25 in) diameter borehole.

Jan 1, 1990

Current research in comminution includes efforts to increase the efficiency of mineral processing systems and reduce the amount of electrical energy needed for size reduction. In most mining operations, comminution begins with blasting. Normally, blast design focuses on loosening material for excavation and sizing the product for efficient haulage. It is likely that blasting also results in internal damage to rock fragments within the blast pattern which may provide subsequent comminution benefits. If substantial comminution benefits exist, appropriate modification to blast pattern design may reduce the overall electrical energy needed for mineral liberation.

Jan 1, 1996

By Minoru Kawamura, Yukio Kato, Yoshikazu Hirosaki, Satoru Suzuki

A wireless blasting system for tunnel construction which consists of a loop antenna, oscillator and blaster, has been developed. The basic technology of this method had been studied in the 1970s to develop a wireless initiation system for undersea blasting and has been successfully used as a Remote Controlled (RCB) system in the Honshu/ Shikoku Bridge construction project in Japan.

Jan 1, 1998

By George P. Schivley

The careful positioning of the drill rigs that drill the holes into which explosives are then loaded is critical to the success of the subsequent blast. Today a system of satellites in space, each transmitting radio signals, is being used to provide the data to allow for tracking and positioning of various types of ground-based mobile equipment. The system is the Global Positioning System or GPS for short. This paper focuses on the application of GPS to surface mining and in particular the navigating of rotary drills from hole-to-hole and their final precise positioning to drill each blast hole.

Jan 1, 1996

By David A. Paul

Over the past several years a great deal of information on blasting vibrations and their effects on structures has been generated. Much of this knowledge has been gained through the use of ground vibration measuring equipment. While this type of information is valuable and gives us great insight into damage that can be incurred by structures from this source, very little, if any, information of this quality is available for the vast majority of cases in which an engineer is called upon to investigate alleged damage from ground vibrations. For the investigative engineer, then, the problem becomes one of accumulating whatever data is available and drawing a conclusion as to whether or not the subject structure was in fact damaged by the blasting vibrations. Such an analysis certainly requires a working knowledge of the literature on the subject and as much experience as he can bring to bear. Even thus armed, however, the data is often ambiguous, confusing, and/or contradictory. A practical approach is presented herein to aid the engineering investigator in arriving at the best possible conclusion available with the information at hand.

Jan 1, 1983

By Richard J. Mainiero

Traditional techniques for the experimental determination of toxic fumes produced by the detonation of high explosives are not applicable to blasting agents. To detonate properly, blasting agents require confinement, a significant booster, charge diameters of 3 inches (7.5 cm) or greater, and charge lengths greater than two times the charge diameter. Without these conditions, blasting agents will not detonate at full order, leading to a misrepresentation of the gaseous products.

Jan 1, 1997

By Daniel Roy, Chris J. Preston, Ron J. Elliott

This paper discusses the use of pressure transducers in water filled boreholes in conjunction with surface mounted geophones to gather field data for in-situ dynamic rock properties determinations. A high speed collector is used to capture the data in the field. The calculated P and S wave velocities and rock density measurements are used as input into the Blastcalc program where the values of Young`s Modulus and Poissons Ratio are calculated. The rock properties information is used along with geological structural data and explosives properties in a 3-D blast modelling program to calculate predicted fragmentation distribution and other blast performance criteria based on the proposed blast design.

Jan 1, 1996

By Wang Zhong Qian, Liu Hui

The paper proposed a fractal and damage model for rock-breaking by blasting, which assumed that the process of rock-breaking results from intrincent fractal development and the accumulation of damage. Remarkably, the process is of fracture character. Based on the model, a computer program is compiled to calculate the 3-dimension damage distribution in blasting crater. Trial results agree well with the predicted results, showing the model set up in the paper is sound.

Jan 1, 1997

By Catherine Johnson, Barbara Rutter

The shock tunnel located at the Missouri University of Science and Technology Experimental Mine is 65 feet 9 inches (20.0406 m) in length. The tests performed inside of this tunnel are either arena tests or shock interaction and transfer (SIT) tests. Arena tests simulate a large open air blast, with lower explosive weights, by elongating the impulse of the blast wave. SIT tests are conducted to determine how the produced shock wave interacts and transfers its energy into a target object located at the end of the tunnel. The target used in this research is multilayered, with each layer being a different material. The targets are 2 ft. by 4 ft. (0.6096m by 1.2192m) pieces of Medium Density Fiberboard (MDF), DOW polystyrene foam insulation, and gypsum drywall. The order of these materials varies with each test. This shock tunnel is unique, because the geometry changes along its length. To fully understand how the shock waves are affected by these changes, a working model was needed. The second purpose of this model is to confirm the maximum charge size of 400 grams (14.11 oz.) of C4 that can be detonated inside the tunnel without causing damage to or failure of the tunnel, thus reducing the amount of time needed in downtime and repair. The model predicts pressures in various locations both within the tunnel and the attached target, thus assisting in determining where failures would likely occur. In the process of generating this model, several problems were encountered, including filling the tunnel with air, meshing the complex geometry, and creating the tunnel in a CAD system. This paper will discuss how these problems were solved. A working model was created by using ANSYS Explicit Dynamics and ANSYS Autodyn. The tunnel geometry file was created using SolidWorks and includes the complex geometry changes along with the target and its mount located at the end of the tunnel. The results produced by the model were compared to the field SIT tests. The comparison of the results from both the model and the experimental testing showed a similar trend in the pressure traces.

Jan 1, 2018

By Kevin Cole, Dennis A. Clark, F William Laslow

Since 1976, the Metropolitan Sanitary District of Greater Chicago, (MSDGC), has commissioned the excavation of a tunnel system in the Chicago area, hundreds of feet below the surface in solid limestone. This paper outlines the blasting patterns, explosive selections, and monitoring techniques used to assure a satisfactory job completion, following the specifications.

Jan 1, 1982

By Conny Postnpaok, Mark E. Hammele

"A major problem that has continued to plague the surface oil industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through several years of field research in full-scale production environments. Many operations across the United States havebeen evaluated ."

Jan 1, 1989

By John L. Floyd

A personal computer is a valuable tool for blast design and analysis. Programs designed for the personal computer, such as the electronic spreadsheet, can be used for a wide range of applications. The spreadsheet formats discussed in this paper are used for explosive comparison, inventory/shot records, and timing design analysis. Each template can be adapted to fit the individual needs of the end user. An example of a graphically orientated blast design program, written in the BASIC programming language, is also discussed.

Jan 1, 1987

By Surinder Singh, Vassilios Kazakidis, Damian Gregory

Safety, stability, and functionality of mine excavations depend on the structural integrity of the surrounding rock mass. Various explosives and perimeter control blasting techniques have been developed in order to minimize rock damage associated with the conventional drilling and blasting operations. The success of perimeter control blasting depends on many factors grouped in three categories: rock mass features, blast design and implementation, and explosive parameters.

Jan 1, 2008

By Joshua Micah Hoffman, Catherine E. Johnson

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. One potential area from which future talent can be recruited is local student chapters. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements, there is a trend of job placement primarily in the engineering industry. Before the explosives industry can begin to compete with other industries, it should be determined what is drawing the students into these other fields. The work presented in this paper sought to better understand the collegiate student population from which a portion of future explosives professionals will emerge. This was done through the use of an anonymous online survey distributed to the student members of the International Society of Explosives Engineers, as well as, members of SEE student chapters. The survey contained questions about future job and career plans, ideal job placement, and expectations of salary. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry. This information can help steer recruitment activities and job offers. Through understanding what is incentivizing these students who have accepted or plan to accept jobs in other industries the explosives industry can better posture itself to be more competitive in recruiting from the collegiate talent pool.

Jan 1, 2014

By N L. Thomas

Hole size affects many factors which directly influence fragmentation in the muckpile and hence, the cost effectiveness of the entire operation. These factors include production capability, explosives and accessories efficiency and usage and drilling accuracy. In addition, hole size should be chosen to suit the geological conditions. The paper concludes that the optimum hole size is generally the largest that can be used commensurate with production and environmental considerations.

Jan 1, 1986

By Scott Gustfason, Richard N. Snyder

What is a safe stand-off distance? Recent mishaps using conventional blasting equipment have seen flyrock as distant as 3,750 feet from the blast area, or close to three-quarters of a mile, therefore, whether below ground, under water, in surface quarries or at a structural demolition site, data signals riding a radio wave promise a new horizon for the users of both electric and non electric blasting circuits.

Jan 1, 1987

By Ankit Jha, Sudarshan Rajagopal, Purushotham Tukkaraja

Geologic structures are one of the crucial parameters in blast design. Structural geology and rock properties influence drilling patterns, blast layout, and initiation systems. A comprehensive understanding of structural characteristics is essential to achieve the desired blasting objectives. This paper aims to identify geologic features in a bench using images obtained from the drone. Images obtained from mine site are annotated for geological features such as faults and joints. Semantic segmentation of images is achieved using an encoder and decoder structure available in the machine-learning pipeline. The encoder consists of initial convolution and pooling layers to capture essential features of the geology and rock patterns from two-dimensional RGB images. Batch normalization is used to put all the features on the same scale. These images are then inputted as training data for the machine-learning algorithm. Machine learning model is trained on sub-section of interest to achieve reasonable accuracy. Initially, 1000 best annotations were used to train the model and additional samples were added later to achieve more accuracy and avoid iteration of machine learning model in wrong convergence. After the model achieves reasonable accuracy, it is used to recognize geological features on new data. Geological features identified on the new data can be used by the blasting crew in blast design and keeps the geological maps updated that can help the geotechnical team.

By M S. Sandhu

Singrauli area of Madhya Pradesh in India has been developed as the power capital expected to produce around 11000 MW in near future requiring 65 million tonnes of Coal per annum. Thermal power plants were installed considering the vicinity of coal reserves which are minable by open cast mining methods. Crisis of oil in seventies further expedited the process of planning big open-cast projects in the area varying from capacity of 3 million tonnes of coal to 14 million tonnes per annum. A separate company - Northern Coalfields Ltd. was formed to ensure meeting the rising demand of coal required for energy production. Northern Coalfields at present is producing 35 million tonnes of coal and will reach the capacity of peak demand of 65 million tonnes by the turn of the century.

Jan 1, 1998