Search Documents

By J. H. E. Jeffes, K. T. Jacob

The activity coefficients of oxygen in liquid Pb-Sn alloys have been measured between 550 and 1100°C by use of solid oxide galvanic cells: Pt, Ni-NiO | Zr02 Solid electrolyte | O (Pb + Sn), Cermet, Pt; and Pt, Fe-FeO | Zr02 Solid electrolyte | 0(Pb + Sn), Cermet, Pt. Alcock and Richardson's quasi-chemical equation, with the coordination number of atoms set to 2, is found to predict successfully the activity coefficients of oxygen in these alloys. The relative partial molar enthalpy and entropy of oxygen at 1 atom per cent in the alloys have been calculated from the variation of the activity coefficient with temperature. The addition of Sn to an unsaturated solution of O in Pb is shown to decrease significantly both the partial molar enthalpy and entropy of O. As the measurements were restricted to a narrow range between 750 and 1100°C in Pb-rich alloys, however, the pronounced variation of the partial molar enthalpy of O with temperature at constant alloy composition predicted by the quasi-chemical model could not be verified.

Dec 1, 1971

By A. B. Holland-Batt

Two graphical techniques which are commonly used to assess batch separations are analysed in terms of reaction kinetics to provide a more powerful method of evaluation. An alternative and more general approach, based on the selection and application of suitable efficiency criteria, is also presented. The method proposed distinguishes between selection and collection efficiency in flotation and can be used to estimate the degree of liberation in the feed. Two examples are given: table concentration of monazite and ilmenite from a beach sand, and flotation of a pyrite-haematite ore

Dec 1, 1971

By R. Trueman, D. B. Tyler

Numerical modelling was used to determine the magnitude and direction of stresses around drives both adjacent to and distant from open stopes in the South Crofty tin mine. Modelling predicted that drives near the stopes are situated in a stress-relaxed zone. The peripheries of drives that are sited in solid rock away from the influence of stoping are in compression. Key-block modelling was used to determine the typical geometries of critical blocks and distinct element modelling was used to determine block stability. The conclusions derived from modelling fitted the observational data. This indicated that key-block theory is a valid tool for analysing the stability of roadways in the South Crofty mine. The support requirements for drives located next to stoped-out areas were formulated using a risk analysis approach to key-block formation. The results were compared with support guidelines derived using empirical design methods. Good agreement was obtained for the roofs of the drives but not for the sidewalls. The concept of a critical excavation width was formulated: once an excavation is larger than the critical size the length of rockbolts need not be increased as the excavtion dimensions increase. This may be the case in all rock mases.

Jan 4, 1993

By A. Paulin, A. W. D. Hills

The work has shown that packed-bed behaviour can be predicted from the results of single-particle experiments, total reaction times being predicted somewhat more accurately than gas and solid temperatures and gas compositions. A small laboratory packed-bed reactor was built and used to study the decomposition of beds of specially prepared CaCO3 spheres, steps being taken to minimise the effects exerted by the walls of the bed on processes occurring within the bed. Gas and solid temperatures and gas compositions were measured at various points in the bed and compared with theoretical predictions based on kinetic data determined in previous single-particle experiments. The measured solid temperatures and total reaction times agreed remarkably well with the values predicted theoretically. Gas and solid temperatures measured after the reaction had finished at any point in the bed did not agree with the theory. This was because solid temperatures in the bed rose very rapidly once the reaction was completed and the walls of the bed could not be heated at a sufficient rate for their temperatures to rise as rapidly; thus some loss of heat from the bed to the walls was inevitable, and this could not be accounted for in the theory. In addition, the theory did not allow for the conduction of heat within the bed, and this resulted in some further slight discrepancy between the measured and predicted values, particularly after the reaction was completed. Gas compositions measured in the bed were rather scattered, but, even so, they agreed moderately well with the predictions of the theory.

Dec 1, 1971

By B. Sonmez, B. Aksanl, S. Ersaym, I. F. Erkal, S. L. Ergun

The comminution circuit at the plant has experienced severe problems arising from a feed containing much larger amounts of clay and having a higher moisture content than expected. Three solutions were proposed: replacement of the crushing circuit by tooth roll-type crushers; using washing drums; and introducing primary autogenous/semi-autogenous millling instead of crushing. Computer simulations studied the effects of the first two solutions on the circuit capacity. Laboratory and industrial scale ball mill batch grinding tests were carried out. The parameters of a kinetic model were determined. The ball mill circuit was sampled and operating model parameters were calculated. The ability of batch grinding parameters to represent the operating conditions was studied. Tests failed to find acceptable model parameters, but parameters from an industrial size batch mill were found to be suitable for simulation studies. The simulations indicated that a continuous feed of -12 mm provided by tooth roll crushers would maintain the desired capacity. Increasing the feed size to -25 mm would reduce the capacity by 8-15%. The use of washing drums could also solve the capacity problem, but small fluctuations in water flow rates might result in problems of excess water in the grinding circuit.

Jan 4, 1993

By Gibson J.

Written discussion contributions to the paper presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, comprise comments by Kilpatrick W.M., Routledge W.H., Watson J. and Smith W., along with the author's reply. Also briefly noted are the demonstration of two pieces of equipment, an incline chock and a cage arrestor

Dec 1, 1916

By T. J. White, R. A. Farnfield

Early computerised blast monitoring equipment consisted of a digital version of the existing analogue machines with, perhaps, a few enhancements. Many additional facilities have since been developed to enable the efficient collection of high quality data. These developments are examined with reference to digital sampling, triggering systems, the storage of complete recordings and signal processing. Recent advances have been made in the use of blast monitoring systems that comprise multiple blast monitoring locations with centralised control and data collection. Software has been developed to help record blast parameters and assess environmental effects. Computer databases have many advantages over their paper counterparts. Data can be easily retrieved and processed. The scaled distances used in the prediction and control of peak particle velocities can be calculated rapidly when the data are obtained directly from a database. Since the whole vibration signal can now be recorded, signal processing can be used to provide information such as signal length, dominant frequency and response spectra.

Jan 4, 1993

By Dean S.

Further discussion at the The Midland Counties Institution of Engineers' general meeting held in Nottingham on 6th May 1916, of the paper published in Trans. I.Min.E., vol.L, 1915, p.179, included brief oral contributions by Bragge G.S., Lewis W.H. and Hepplewhite W.H.

Dec 1, 1916

By V. E. Ross

A comparison was made of three methods for determining the contributions of true flotation and entrainment during batch flotation tests. In the first method size-by-size recoveries are measured in both the presence and the absence of a collector, a frother being present in both tests. In the second method the mass of solids and water recovered after a chosen time of flotation is varied by changing the rate of froth removal and the depth of the froth. The third method uses a transfer factor to describe the classification of solids and water, and hence the changes in the composition of the pulp, during a single flotation test. Batch flotation tests were carried out with artificial mixtures of pyrite and gangue, the amount of floated material recovered being calculated according to each of the three methods. The discrepancies betweeen the calculated amounts are analysed in terms of the assumptions that are made for the various methods and the most suitable conditions for the application of each method are identified

Dec 1, 1991

By E. A. Brocchi, P. K. Jena

Complete extraction of copper from Salobo chalcopyrite concentrate can be achieved in less than 10 minutes by chlorination of the dry concentrate with Cl2 at 450 degrees C and in 5 minutes by chlorination of an aqueous slurry containing 5 wt% concentrate at 30 degrees C. In general, slurry chlorination appears to be faster than dry chlorination. The kinetics of dry chlorination of copper sulphide are controlled by an adsorption mechanism with an activation energy of 6.1 kcal/mole. The rate is independent of chlorine partial pressure when pCl2 exceeds 0.4 atm. In slurry chlorination the dissolution of copper sulphide follows a topochemical reaction model and the rate of chlorination decreases with increase in pulp density and also temperature. Dissolved chlorine appears to take part in the reaction in atomic or ionic form.

Jan 4, 1992

By NA NA

Stamler Corporation manufactures of mining machinery and material handling equipment specialising in Feeder-Breakers to the mining and quarrying industries.

Jan 9, 1996

By R. Patel, J. Ephraim

The production of titanium dioxide (TiO2) from its minerals such as ilmenite is challenging, and subsequent isolation of titanium from TiO2 is even more difficult because of the metal-oxygen bond strength. Currently, titanium sponge is mainly produced via the Kroll process, which is energy intensive and generates large quantities of waste. A number of international research groups have come up with technologies for the production of titanium metal. However, none of them have been commercialised, because of engineering or economic issues. The team at Bradford have confirmed that ultra-pure titanium powders can be separated from TiO2 powder through metallothermic reduction and are working to scale up the process.

May 1, 2015

By L. Wade, R. Wang, M. A. Horton

Laboratory methods to find the mechanical properties of rock are inherently biased towards stronger strata, which best survive the sample preparation process. Geophysical techniques are not subject to such bias and may be used to predict mechanical properties rapidly and cheaply. Samples (151) were obtained from a borehole that had been comprehensively geophysically logged. The mechanical properties of the samples were established in the laboratory and correlated with the geophysical responses of the strata from which they came. The results indicate that, for homogeneous strata at least, it is possible to predict the unconfined compressive strength reasonably well from sonic travel time measurements made in the field. Predictions of static Young's modulus may also be made from this data source, but with a lesser degree of confidence. A multivariate regression equation is presented which relates down-hole sonic travel time to unconfined compressive strength, depth and the frequency of fractures in the rock mass. This equation may offer potential for the prediction of the mechanical rock properties of fractured and layered strata.

Jan 4, 1993

By J. Cech

Discussion is presented of a decision-making support method for the spacing of ore passes along a long vein orebody and the division of the orebody into convenient stopes for future mining operations. The method was tested on a Slovak siderite deposit and also on some hypothetical cases with the objective of obtaining more general results

Jun 18, 1905

By R. G. Siddall, W. Gale

In the UK the development of the science of strata control has been strengthened by a resurgence of interest in the specialism of roofbolting and its associated techniques. The evolution of the theories and practices of strata bolting in roadway stabilisation is discussed. Practical experiences are considered, principally the use of Australian techniques, the relationship between bond strength and annulus and the effects of stress in the ground. Areas of new technology such as cable bolting, injection anchors and on-board bolters are also discussed. The recent advances in computer technology and rock testing equipment and methods have provided the opportunity to simulate ground behaviour under various conditions. Computer modelling developments and the use of techniques to predict ground behaviour are described.

Jan 4, 1992

By Jones R. G.

Dr Pat Foster, Senior Lecturer in Mining Engineering at the UK's Camborne School of Mines, talks to Rhiannon Garth Jones about mining safety around the world, education and the future of the industry

Feb 1, 2015

By R. G. Jones

Many novel projects suffer delays, cost overruns or failure because of inadequately qualified technologies. A new qualification to measure the quality of innovation is discussed.

Jul 1, 2015

By NA NA

Background information on Exchem Mining and Construction and its products.

Jan 7, 1997

By T. T. Chen, J. E. Dutrizac, C. Canoo

The calcine consists principally of ZnO and ZnFe2O4, which occur as banded and porous grains, together with lesser amounts of Zn2SiO4, Zn-Fe-Pb silicate, sphalerite, quartz, PbSO4 and Fe2O3. Al is present in solid solution in most of the Fe-bearing phases and also as residual aluminosilicate minerals from the original concentrate. Si occurs mostly as Zn2SiO4, Zn-Fe-Pb silicate and as residual silicate minerals. As is commonly found in the ZnFe2O4, Fe2O3 and Zn-Fe-Pb silicate phases. The major As carrier may be calcium arsenate particles less than 1 micrometre in size which are dispersed throughout the calcine. The neutral leach residue consists mainly of ZnFe2O4 and precipitated masses of iron gel-silica gel. Lesser amounts of ZnO, Zn2SiO4, Zn-Fe-Pb silicate, PbSO4, sphalerite, Pb-K-jarosite and basic zinc sulphate are also present. Al occurs in minor concentrations in most of the Fe-bearing phases and in the Zn-Fe-Pb silicate. The residual aluminosilicates are also an important Al carrier. The major As carrier is the precipitated iron gel-silica gel phase, but some As is also present in the Zn-Fe-Pb silicate, ZnFe2O4 and Fe2O3 phases. Silicon is divided about equally between the iron gel-silica gel, Zn2SiO4, Zn-Fe-Pb silicate and residual silicate minerals. The weak acid leach residue is generally similar to the neutral leach residue except for its reduced content of ZnO and basic zinc sulphate.

Jan 4, 1993

By E. A. Brocchi, D. H. Gameiro, P. K. Jena

Carbon tetrachloride was found to be a very efficient chlorinating agent for anatase concentrate, even at the low temperatures that were investigated (250-400 degrees C). For example, at 400 degrees C about 90% of the anatase concentrate was found to have been chlorinated within 60 minutes

Jun 13, 1905