Search Documents

By Yuexin Han, Wenbo Li, Yan Shan, Yanjun Li, Shumin Zhang

"With the accelerating pace of resource extraction, the quality of resources is decreasing, and the old tailing dams which have served for several decades have become the focus of attention. The secondary recovery of valuable metals in the tailings is an important aspect of the comprehensive utilization of tailings. The average iron content of iron tailing is 8%-12% in China. The research aimed at exploring the low-cost and efficient technical route to recycle eastern tailings of Anshan iron mining area. The purpose of the research is to scientifically find the rational conditions of magnetizing roasting and to provide an increase in recovery and quality of concentrates. The eastern tailings of Anshan mining area belong to high silicon bearing iron tailings, iron mainly exists in form of hematite-limonite with an iron grade of 10.60%, the main component of gangue is SiO2 with a grade of 76.22%. In order to reduce the influence of the tailings on the environment, fluidized magnetizing roasting and low intensity magnetic separation for the eastern tailings of Anshan mining area were carried out to improve the utilization of the tailings. The results indicated that an iron concentrate with an iron grade of 65.30% and a recovery of 85.85% could be obtained under the conditions of gas flow rate 8 m3/h, H2 concentration 50%, fluidized magnetizing roasting temperature at 600? for 20s. Phase analysis, magnetism analysis and XRD analysis on roasted materials indicated that hematite-limonite could be transformed to magnetite during the fluidized roasting, then the effective separation of iron and gangues could be made easily by the weak magnetic separation. INTRODUCTION It is universally acknowledged that the grade of iron ore in China is low, the output rate of iron ore tailings is high, usually more than 60%. At present, the comprehensive utilization rate of iron ore tailings is low in China. Generally, the iron ore tailings are stockpiled in the tailings dam. The tailing dams not only occupy a lot of land, but also takes a lot of money to construct and maintain. In addition, the noxious substances in the tailings, such as residual flotation agents and heavy metals, have a severe impact on the ecological environment. There is little doubt that tailing dams have a visual impact on the environment due to their regular geometric shape. Iron tailings can be treated as compound mineral, which is an important component of comprehensive utilization of mineral resources, and is an has been widely concerned. Lots of scholars have done a large amount of research work on a large number of iron ore tailings. Since the iron mineral crystal grain size is fine and the iron grade is low, the iron tailings have failed to achieve good selection criteria."

Jan 1, 2018

By N. S. Voiloshnikova

Large-scale continuous ?Resin-In-Pulp? process tests were conducted at Irgiredmet. The object for testing was the sample of oxidized gold ore from one of Siberian deposit. Weak-base ion ex-change resin PuroGold was used as adsorbent. The duration of ?Resin-In-Pulp? tests was sufficient for a completing of three cycles ?Adsorption/Elution?. Gold in feed was 0.95 mg/L. Gold in solid phase of adsorption tails? 0.065 g/t. Gold in liquid phase of adsorption tails? 0.026 mg/L. Total gold in adsorption tails ?0.11 g/t. Gold recovery ?94.3 %. The use of regenerated resin had practically no effect on gold losses with adsorption tails. Alkaline cyanide solution (NaCN-20g/L, NaOH- 5g/L) was used as eluent for gold elution from loaded resin. Elution temperature ?60 °C. Number of eluent bed volumes passed ?10. Loaded resin analysis was following (g/ton): Au? 1700~1250; Ag? 400~460; Cu? 250~450; Zn? 5100~9600; Fe? 860~1200. Elution efficiency: Au? 95.3%~97.8%; Ag? 84.0%~88.0%; Cu? 84.0%~88.0%; Zn? 97.0%~99.0%. Although high zinc resin loading was shown zinc was eluted efficiently. The adsorption properties of fresh PuroGold resin, PuroGold resin after 3 cycle ?Adsorp-tion-Elution?cycles in comparison with AM-2B resin were tested. It was shown from adsorption isotherms that selectivity of PuroGold resin slightly less in comparison with AM-2B resin mainly due to its higher zinc adsorption properties. It was founded on base of test results that adsorption properties of PuroGold resin was practically constant during three ?Adsorption/Elution? cycles. Gold may be efficiently recovered by resin tested. There were no difficulties during gold elution from loaded resin and its regeneration. PuroGold resin was recommended for industrial use in RIP process. Process design criteria were developed and plant design is on progress at the moment.

Jan 1, 2014

By S. Serranti

A fast, reliable, and low cost characterization of ore minerals products, as they result from different processing actions, represents one of the most challenging targets in the mineral processing sector. Today different techniques are available according to different sampling strategies and analytical principles. In this paper, the possibilities offered by the adoption of hyperspectral imaging based sensing units working both at micro- and macro-scale are presented and discussed. According to the different phases and stages of ore minerals and products characterization, and starting from the analyses of the detected hyperspectral firms, it is thus possible to derive useful information about mineral flow stream properties and their physical-chemical attributes. This last aspect can be utilized to define innovative process mineralogy strategies and to implement on-line procedures at processing level. The present study discusses the effects related to the adoption of different hardware configurations, the utilization of different logics to perform the analysis and the selection of different algorithms according to the different characterization, inspection, and quality control actions to apply. Keywords: process mineralogy, hyperspectral imaging, NIR spectroscopy, surface mapping, textural analysis, quality control

Sep 1, 2012

By R. Lestari

Newmont Batu Hijau operates with an accelerated mining rate to optimize life of mine (LOM) project economics. This results in a portion of ore mined being stockpiled for reclaim and processing throughout, and at the end of mine life. LOM economics can be further enhanced by preserving stockpiled ore value by mitigating oxidation effects. A detailed stockpile ore oxidation study was conducted to: ?? Develop a practical understanding of how oxidation affects ore value; ?? Determine how oxidation rate can be controlled, and; ?? Determine how oxidation effects can be mitigated to preserve ore value. The result of the study is a stockpile management strategy that significantly reduces oxidation related losses and, implementation of that strategy within practical constraints. Implementation includes installation of Controlled Potential Sulfidisation (CPS) flotation to facilitate oxidised sulfide copper recovery and, recovery of dissolved copper from stockpile drainage solution into saleable product. This paper describes the study results including managing and predicting stockpile oxidation with time, monitoring performance of implemented CPS flotation and recovery of dissolved copper from stockpile drainage. These are essential elements of successful long term mine operation in Batu Hijau.

Jan 1, 2014

By P. Han

The preparation technological conditions and regeneration method of two novel granulated adsorbing materials of rectorite/fly ash composite (Material 1) and rectorite/water quenched - slag composite (Material 2) and the use of them to remove heavy metals from copper smelting plant wastewater have been studied. The experimental results showed that under the preparation conditions with the ratio of rectorite to fly ash or water - quenched slag of 1:1, the amount of the additive (Industrial Starch, IS) of 15% (Material 1) or 10% (Material 2), the addition of 50% water, and the calcination temperature of 500? (Material 1) or 400? (Material 2), the efficiency of heavy metal removal with the granulated materials was the best, whereas the ratio of disintegration loss was the lowest. Under the treatment conditions of natural pH, and with the addition of the granulated materials of 0.07g/cm3 (Material 1) or 0.05g/cm3 (Material 2), a reaction time of 60 minutes (Material 1) or 40 minutes (Material 2), and the adsorption temperature of 25?, the efficiency for the granulated materials to remove Cu2+Pb2+Zn2+Cd2+ and Ni2+ from the copper smelting plant wastewater was 98.9, 97.5, 96.7, 90.2, and 79.1, (Material 1) or 98.2, 96.3, 78.6, 86.2, and 64.2, (Material 2), respectively, and the quality indexes of the wastewater after treatment conformed with the first level of integrated wastewater discharge standard (GB8978-1996). When the adsorption of heavy metal ions on the surface attained saturation the granulated materials could be regenerated by washing with 1 mol/L sodium chloride (NaCl) solution and still with quite good heavy metal removal efficiency. The granulated adsorbing materials had the advantages of high efficiency of wastewater treatment, easy method of solid-liquid separation and regeneration, and a broad prospect of applications.

Jan 1, 2014

By Markus A. Reuter, Joep Verwoerd, Marc J. A. Pijnenborg, Yongxiang Yang

"Incineration is a proven disposal technology for all waste materials with heat release potentials, and provides high degree of toxic destruction and control for a broad range of hazardous materials. In the Netherlands, all the hazardous wastes are processed at AVR-Chemie located at the Rotterdam harbour, through rotary kiln incinerators. The newly enforced regulations from the European Union with stricter emission levels require a better understanding of the incineration process and improved process control. However, the transport phenomena and combustion processes within the kiln system are very complex and not well understood. In order to get better understanding of the incineration process, research has been carried out to study the fluid flow and combustion behaviour of the incineration system. Computational Fluid-dynamics (CFD) was used to simulate the gas flow and waste combustion process, and temperature measurements of the operating rotary kiln incinerator were conducted to validate the CFD model. This paper will present the latest results from the current research project for simulating gas flow and combustion heat transfer for a wide range of hazardous waste streams.The simulation of the waste incineration process was carried out using a general-purpose CFD code Phoenics. The rotary kiln and the secondary combustion chamber (SCC), with a waste processing capacity of 50,000 ton/y and an energy input of 30 – 40 MW, is translated into a CFD model. The model includes a k-e turbulence model and a global gas-phase combustion model (3-gas or 7-gas combustion model). The 3- gas model (Simple Chemically-Reacting System, SCRS) predicts only the thermal effect of the fuel combustion, and only one global fuel is used, therefore, real chemical species are not taken into account. In the 7-gas combustion model, (an Extended SCRS, ESCRS), different forms of waste fed into the incinerator have been modelled into a mixture of a general hydrocarbon fuel C3H4 and other components such as CO, CO2 and H2O. Thus, all the incoming fuel streams with different compositions and calorific values can be properly converted into separate inlets. The combustion of the waste is assumed to take place only in gas phase in two steps: (1) primary combustion of the main fuel component C3H4 to form CO and H2, (2) secondary combustion of CO and H2O to form CO2 and H2O. The rate of each combustion reaction is assumed to be controlled by turbulent mixing of fuel and oxidant (air or oxygen), i.e. the Eddy-Break-up (EBU) model. The resulted temperature field was validated with temperature measurement data, and the simulated temperature distribution from both 3-gas and 7-gas model have reasonable agreement with the measured data."

Jan 1, 2003

By Junwei Han, Kai Xue, Wenqing Qin, Tan Xu, Fen Jiao, Lianbing Cai, Wei Liu

"The research aimed at solving the problem of the stacked spent magnesia-chrome refractories using in non-ferrous metal smelters, which contain various heavy metals and are considered as a hazardous waste. The purpose of the research is to recycle the spent refractories environmentally and economically using gravity separation and flotation to obtain metal concentrates for smelting and using chloridizing volatilization to remove the trace metals from tailings, providing raw material to reprocess magnesia-chrome refractories. In the course of the study, laboratory techniques for the preparation of experimental samples of spent magnesia-chrome refractories were developed including the sequence of operations of material grinding, gravity separation, tails regrinding, flotation, filtration and subsequent unification of concentrates, filtration and chloridizing volatilization of tails, and collection of volatiles. Laboratory tests carried out on several types of samples of spent magnesia-chrome refractories from different smelters showed that gravity separation provided increase in quality of concentrates including about 80% metals (including Ag, Pb, Bi) and flotation separation provided increase in recovery of concentrates under the condition of 200g/t of emulsified kerosene, and 500g/t of combined collector. Based on combined technology of gravity and flotation separation, about 90% metals were recovered from the refractories by a closed-circuit test and the total concentrates contained 40% metals, which can be returned to smelting process as a feeding. Because a small amount of metal in raw materials will seriously affect the performance of refractories, chloridizing volatilization is necessary for removing the remaining 10% metals from tails mixed 8% coke and 13% magnesium chloride at a temperature of 1200°C. Thus, the tailings can be reused as a raw material for new refractories.INTRODUCTION Magnesia-chrome refractory has been used extensively in various industries such as secondary metallurgy, non-ferrous furnaces and cement making due to their high temperature stability, low thermal expansion and outstanding erosion-corrosion performance at high temperatures (Gotod et al., 2005; Vezza et al., 1997; Gregurek et al., 2015). Generally, the magnesia-chrome refractories are produced from a mixture of magnesia and massive variety of chrome ores. However, massive chrome ores are being depleted throughout the world. Even more serious is that the heavy metal chromium (Cr) can transfer into soil and water, which will have an influence on the survival and development of human beings (Zhao et al., 2006; Jiang et al., 2004; Qintie et al., 2013). As a result, regulations treating spent magnesia-chrome refractories as potentially hazardous waste are being enforced, making their disposal difficult and expensive."

Jan 1, 2018

By A. Gül

This investigation was carried out with low grade Murgul-Cakmakkaya copper ore once used to be dumped away as waste material. Sulphide minerals in the ore sample observed are chalcopyrite, pyrite, sphalerite and to some extent molibdenite; quartz, calcite and dolomite are the gangue minerals. The ore sample assays 0.28% Cu, 2.94% Fe and 3.36% S. Mineralogical study of the ore sample showed that adequate liberation of chalcopyrite for flota-tion was achieved below 100 µm. In flotation tests Aerophine 3418-A was the collector employed, NaOH or Ca(OH)2were the pH modifiers. Deactivators used were sodium meta bi-sulphide, starch, dextrin and lime. MIBC was the frother used throughout the tests. Test results showed that starch alone was the most suitable depressant to give the optimum metal content and recovery val-ues. Activated charcoal was used to adsorb excess collector species in the flotation pulp during cleaning stages After two stages cleaning of the rougher concentrate using starch as the depressant a copper concentrate assaying 21.2% Cu was obtained with 79.5% recovery while the tailings contained 0.01% Cu and metal losses were about 3%

Jan 1, 2014

By D. Gucbilmez

Three spiral concentrators having different geometries were compared in a chromite processing plant. They had different diameters, helix-cross sections and capacities. Two of the spiral concentrators were manufactured in China and one of them was manufactured in Australia. The tests were carried out in a closed circuit experimental setup by using a low grade chromite ore. The pulp densities kept the same during the operation, and the samples were taken simultaneously. The effects of the different positions of the splitters on separation and the feed rate were the parameters that were observed during the experiments. The performances of three spiral concentrators were found to be different. To clarify the effect of the particle size on the separation in spiral concentrators, the screening was applied to the feed. The samples were sieved from 75µm. The test results indicated that the separation performance decreased dramatically in very fine particles. Although fine particles caused some problems in spiral concentrators, fine grinding is required for this particular chromite ore for better liberation. A suitable method for the fine particles should be investigated for acceptable recovery.

Sep 1, 2012

By B. Q. By

TiO2 is an ideal material for catalytic technology due to its unique properties. In this paper, Sm3+ doped TiO2 photo-catalyst was developed to improve the efficiency of TiO2 and to use the natural light as irradiation source, which was made from Titanium Tetrabutoxide and Samarium Oxide with the Sol-Gel process. The Sm3+-TiO2 photocatalyst was used to degrade reactive orange 4 (RO4) in Azo Dyes. The effects of solution pH, Sm3+ concentration and catalytic time on the degradation rate of RO4 were studied. The characteristics of the catalyst were analyzed with XRD and TEM. The experimental results show that the catalyst has high activity in the degradation of RO4. The Azo bonds of RO4 are active and easily broken by oxidation. The catalytic activity of the Sm3+ doped catalyst greatly depends on the pH of solution. The catalyst has high photo-catalytic activity at both neutral and alkaline conditions. The degradation mechanism of the Sm3+ doped TiO2 photo-catalyst was also discussed.

Jan 1, 2014

By A. V. Bogdanovich

In diamond ores processing, final waste tailings size, rejected to dump, is one of the most important parameters. On one side, it is necessary to minimize losses of diamonds, whose size exceeds 1 mm, on the other side ? to provide for the plant high throughput and sufficiently low capital and energy costs, which is in greater part connected with disintegration process. Extensive laboratory, pilot-scale and commercial-scale dressability studies of different types of diamond ores have been performed at JSC ?Mekhanobr Engineering? in recent years. With that, special consideration was given to determination of the required ores? disintegration size that would provide for a high recovery of diamonds. In diamond ores processing, in order to exclude breaking of large diamonds, stage disintegration is used with regrinding of light fractions and heavy fraction X-ray fluorescent separation tailings. On account of rather weak bonds of diamonds with enclosing minerals, in crushing and grinding of diamond ores, selective disintegration takes place, with aggregates? breakup along plane surfaces of least bonding, which facilitates liberation of diamonds and their transition to free state. Heavy components losses with different sizes of final dump tailings were studied in processing of large samples. It was established, that in order to almost completely exclude losses of heavy components over 1 mm size, light fractions had to be ground to 2.5-3 mm size, while X-ray fluorescent separation heavy tailings of -15+3 mm size do not contain diamonds larger 1 mm in aggregates, and their regrinding does not increase total recovery of diamonds. On the basis of the conducted studies, relationships regarding heavy components and diamonds losses with respect to diamond ores final disintegration size were obtained, providing for more rational organization of the ores disintegration and processing flow sheet. Keywords: diamond, waste tailings size, disintegration process, recovery of diamonds

Sep 1, 2012

By William Skinner, Jonas Addai-Mensah, Keith Quast, David Robinson, Jason Connor

A review of the laboratory- and pilot plant-scale physical separation techniques for the beneficiation of nickel (Ni) laterites shows limited efficacy. To date, the only upgrade technique adopted commercially, prior to hydrometallurgical processing of Ni laterites, is the removal of a barren, coarse size fraction in the feed by classification. In the present work we investigated two low grade (~ 1%), goethite-rich Ni laterite ores’ upgrading by magnetic separation, attritioning/coarse, (lower Ni-grade) gangue rejection and flotation techniques. Low intensity (0.1T) dry magnetic separation at ambient temperature of raw samples and those pre-heated at temperatures up to 450 °C showed evidence of pay metal Co and Mn bearing asbolane and/or lithiophorite minerals pre-concentration in the magnetic fractions. Ni distribution, however, did not show any noticeable magnetic upgrade but followed the weight distribution. Other ore pre-treatment methods (e.g., desliming and sulphidisation) followed by froth flotation with anionic and cationic reagents also led to noticeable (~35%) Ni upgrade. This is due to the deportment of Ni across several gangue host mineral phases (i.e. Fe oxide/hydroxide and a range of silicate/aluminosilicate minerals). From chemical analysis, after disaggregation of ~ 1% Ni grade feed ore, coarse (-600 + 38 µm) and fine (-38 µm) fractions of ~0.6% and 1.3% Ni grades respectively, were also produced, suggesting that a significant upgrade in Ni content can be achieved by rejecting the + 38 µm fraction with the loss of <40% of the Ni. The ore mineralogy, particularly the complexity and high number of un-liberated Ni-bearing phases, greatly compromises physical separation methods for these ores, with the possible exception of screening after disaggregation of the fines inherent in the run of mine ores.

Jan 1, 2014

By Z. G. Song

As a kind of complex physicochemical process, grinding would affect the subsequent mineral processing such as flotation considerably. In this study, the effect of wet grinding on malachite and calcite flotation using sodium oleate as collector was studied. And the mechanism of the effect of grinding was investigated. Laboratory scale grinding and flotation testing of malachite and calcite samples were performed. Different grinding media were used, including steel balls and zirconia balls. It was the aim of this work to study the effect of grinding on the pulp chemistry paying particular attention to flotation recovery. The effect of grinding media and different addition location of sodium oleate on malachite and calcite flotation was studied. The methodology used in this project involved grinding the ore with and without the addition of sodium oleate in mill, measuring the pH and metal ions produced by minerals after grinding, adding various quantities of sodium oleate and determining the copper recovery. The presence of species of products on the minerals after grinding was probed using X-ray photoelectron spectroscopy (XPS), and the metal ions produced by minerals after grinding were measured by atomic absorption spectrometry (AAS). It is showed that the mil-ling environments evaluated significantly affected the flotation of malachite and calcite. This study also discusses the effecting mechanism of grinding environment on floatability of malachite and calcite.

Jan 1, 2014

By Kwan Ho Kim

In this study, free fall tests are conducted with the objective of understanding the breakage properties of waste concrete for the guide of the direction of the better comminution process. Waste concrete of 75mm×53mm is tested at various drop heights with or without heat pretreatment. Test results indicate that a block of waste concrete does not break by free fall, but eventually breaks by repeated free falls. The number of free falls required for complete separation of large aggregates from the cement mortar considerably reduced when the samples were heated at 400?. Therefore, a great energy saving can be obtained when heating the waste concrete prior to crushing. The energy saving was found to be dependent on the height of free fall but in all cases, was still large enough to offset the additional energy required for heating. Also, it was found that the heat pre-treatment gives an additional advantage in that it produced cleaner recycled aggregates. This may result from easier detachment of cement mortar from the aggregates due to weakening of bonding forces by heating. By analyzing the size distribution of the crushed product, a free-fall breakage model is developed using the particle breakage ratio and the breakage pattern. The developed model can be used to predict and to analyze waste concrete processing circuit.

Jan 1, 2014

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By F. Göktepe

Flotation gases and conditioning of the pulp with them are one of the important parameters of flotation and should be taken into account especially in the flotation of sulphide ores. In this study, flotation of pure chalcopyrite and pyrite samples were investigated with air, oxygen and nitrogen as flotation gas and the effect of conditioning with these three gases also were performed. Flotation gas was introduced for 5min, 10min, 15min and 20 min. For chalcopyrite flotation there was no drastic change in recovery when air, oxygen and nitrogen were used as flotation gas but conditioning the pulp with oxygen for 10 minutes increased the recovery about 8% where pulp potential has been approximately 25 mV with chalcopyrite and 150 mV with platinum electrodes. Conditioning with all three gases decreased the pyrite recovery by about 20% with 20 minutes conditioning. Pulp potential decreased in the presence of nitrogen while conditioning with air and oxygen increased the pulp potential for both electrodes. Generally potential increased for both minerals with oxygenation and aeration time but it was stable or slightly decreased with nitrogenation. Comparison of the gases showed that the different flotation gases do not effect flotation recovery but conditioning the pulp with these gases at pre-flotation effects chalcopyrite and pyrite flotation recovery, most dramatically pyrite.

Jan 1, 2014

By R. Marandi

The effective removal of heavy metals from aqueous wastes is among the most important issues for many industrialized countries, How ever biosorption, i.e. the uptake of heavy metals by non- living biomass, has gained increased credibility during recent years. Biosorption of Cr(VI) from aqueous solution, on pretreated and immobilized Aspergillus niger was investigated in a batch and countinuous reactors. A.niger biomass pretreated by boiling in 0.5 N NaOH solution for 15 min, exhibited higher Cr(VI) removal capacity than autoclaved biomass. The optimum adsorption pH value observed for Cr(VI) ions was 2. The Cr(VI)removal rate increased with a decrease in pH. The influence of contact time, pH, Cr(VI) concentration, biomass concentration and temperature on Cr(VI) removal were also evaluated. Biosorption of Cr(VI) on pretreated biomass followed the Freundlich and Langmuir adsorption models.In this study A.niger biomass was immobilized in Na-alginate matrix. The biomass beads packed in a column were able to remove metal ions.In this study we used two different flow rate in a column, 1.5 mL/min and 3 mL/min.The breakthrough data obtained for Cr(VI) was adequately by the Thomas and Yan models and the adsorption capacity of the biomass was found to less than the adsorption capacity obtaind in the batch study. When the beads containing biomass become saturated with metal ions, the adsorbed metals were eluted using 0.5 N NaOH solution. Therefor nearly 90% of Cr(VI) was desorbed by NaOH solution.

Jan 1, 2014

By Bruce Mathema, Steven Huynh, Terry Cheng, Gerry Gomez

"The use of PM40N, a specialty precious metals promoter in conjunction with a standard Xanthate based collector was extensively investigated in the flotation of a complex, silver-bearing, lead-zinc ore containing naturally occurring graphitic gangue. The ore, considered difficult to treat with conventional reagents, was tested at plant scale to determine the impact of the promoter on silver recovery, lead grade and also on the amount of zinc misplaced to the final lead concentrate.Initial laboratory-scale rougher flotation testing implied significant improvements in the recovery of silver and lead with a marginal amount of zinc displaced. Subsequent mini pilot flotation tests further revealed that a gain in selectivity and recovery could be achieved by adjusting PM40N promoter dosage and incorporating a cleaner flotation step, further improving rejection of sphalerite. Plant trials resulted in an improvement of 3% in Silver recovery coupled with a 2% increase in recovered lead whilst maintaining lead grade in the lead circuit.To date, the use of PM40N as a promoter has enabled the processing operation to significantly increase its plant economics. The partial replacement of the standard Xanthate based collector has also reduced the overall quantity of Xanthate required in the standard circuit by approximately 10% - which is a positive impact on the environment. It is envisaged that further optimization of plant parameters will favor stable operation and continue to boost revenues generated by subsequent improvements in silver metallurgy."

Jan 1, 2014

By Leonardo Soto, Fernando Villanueva

"Antofagasta Minerals S.A. (AMSA), for its Centinela District Project, is currently developing, at a first stage, a new 90 ktpd Concentrator Plant incorporating Esperanza Sur (ESP Sur) and Encuentro (ENC) ores. In order to dimension properly main equipment, specifically for grinding circuit, a final decision has been taken using geological and metallurgical (comminution) data from both body ores. Data was analyzed internally within AMSA and its consultants to get a final proposed circuit for further engineering studies. Specific Energy Consumption (SEC) parameter is one of the main key factors for proper dimensioning. To get an accurate value different tests have been made and modelled to ESP Sur and ENC ores. Also, operational data from Esperanza operation has been taken into account due to its similar ore characteristics to ESP Sur ore and incorporated as input data for design. Depending on data, quality and amount, it is possible to estimate accuracy for project investment and risk level, hence investment decision can be taken under good and reliable information."

Jan 1, 2014

By P. M. Solozhenkin, V. N. Kovalev

Russia is a global antimony market leader. The three major antimony production provinces are Sakha Republic (Yakutia), Krasnoyarsk Territory and Trans-Baikal Territory. Russia’s largest antimony resources are Zhipkozhinsky and Solonechensky deposits in Sakha Republic (Yakutia) and Olimpiadinskoe deposit in Krasnoyarsk Territory. This work demonstrates the efficiency of computer programs and chemical technology aimed at the study of the behavior of collectors used in the processes of flotation of antimony, arsenic and Au (I – III) minerals. The most promising collectors for the flotation of ores containing antimony and gold on the basis of P(V) and compounds with S, O and N atoms were chosen. The mechanisms of interaction with the mixtures of two or three components of collectors were studied. High recovery of antimony and gold was reached in the processing of Au-Sb ores of Sarulah and Sentachan deposits in Sakha (Yakutia). X-ray radiometric methods of separation of antimony ores of Trans-Baikal Territory deposits were proposed. In order to choose the most cost-effective solvents for hydrometallurgical processing of Sb, Au-containing concentrates the method based on clusters formation between transition solvents and antimony minerals was suggested. The nature of Au losses was theoretically revealed in the sulfide-alkaline process. On the base of computer simulation, the formation of various complexes of (KAu) types was developed, for example, hydrosulphidic gold, thiosulfates of gold - Na3AuS4O6, antimony and arsenic gold, trithiostibate (III) and trythioarsenate (III) KAu were produced. The practice of processing of goldantimony concentrates to produce high-quality antimony trioxide and antimony-gold containing alloy (AGCA) regarding the special conditions of the Far North region, were analyzed. The affinage of AGCA was recommended. Creative project development of antimony industry in Russia in order to produce antimony compounds and pigments, including pyriform compounds and flame retardants (antipyrenes) is discussed.

Jan 1, 2018