Search Documents

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014

By F. J. Sotiuo

Variability of the quality of phosphate ore feed to the flotation plant has been of great concern for the industry. This variability sometimes resulted in 10% to 50% decrease of P2O5 recovery, a reduction of P2O5 concentrate grade and/or both due to depression of the system. For this investigation, samples of refractory ore and easy-to-float ore were obtained from the same mining area in Central Florida; and then submitted to bench flotation tests using fatty acids (FA). To understand the cause of difference in flotation behavior of these apparently similar ores (grade, mineralogy, and physical appearance), bulk and surface characterization studies were conducted. Based on the results of characterization studies and bench flotation tests on both refractory and easy-to-float samples, it was possible to determine FA surface coverage. It was found that the surface coverage for the refractory ore was between 6.9% and 9.8%, corresponding to 0% and 80% recovery, respectively; whereas the easy-to-float ore showed surface coverage of 17.2% (89% recovery) to 24.6% (98% recovery). Since size analysis, surface area and pore size measurements showed small differences, it was thought that the surface coverage differences could be caused by the ad-sorption of natural compounds onto the phosphate ore surfaces, depressing the system. SEM, EDS, and Leaching and Solvent Extraction (LSX) studies were performed on the phosphate ores to demonstrate the proposed mechanism. This paper summarized our characterization studies, flotation results, and findings. The study showed that the new identified compounds were responsible for the flotation behaviors of the Florida refractory phosphate ores.

Jan 1, 2014

By Vinay Jain

Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. One of the methods by which this problem might be addressed is by design/screening of suitable reagents (flocculants/depressants/collectors) which act selectively towards either aluminum containing minerals (gibbsite and kaolinite) or iron bearing minerals (hematite and goethite) in order to separate them. Our earlier work indicates that separation of iron oxide minerals from gibbsite is relatively more difficult than from kaolinite. Accordingly, our research work has been focused on finding selective reagents for iron oxide ? gibbsite separation. We have performed density functional theory (DFT) computations to evaluate the interaction energies of seven different reagent groups - carboxylic acid, flotol, hydroxamic acid, phosphonic acid, iminobismethyl phosphoric acid, xanthate and starch with hematite and gibbsite surfaces. The objective was to identify if any of these groups show selective adsorption towards one of the mineral surfaces. Among all these reagents, starch exhibits the highest selectivity towards the hematite surface with a difference in interaction energy of ~63 kcal/mol between hematite and gibbsite surfaces. This is consistent with experimental findings at our laboratories on slime samples from Noamundi mines wherein it is being observed that usage of starch as a flocculant does lead to an improvement in the final grade of the ore with significant reduction in the Al-content. A binuclear complexation mechanism based on affinity between Fe and Ostarch atoms combined with a geometrical templating effect, arising out of a close correspondence between Fe-Fe distance on the hematite surface and O-O distance in starch, is proposed to explain the strong adsorption of starch on hematite surface. Keywords: slimes, iron ore, alumina, hematite, gibbsite, DFT, adsorption, flocculants

Sep 1, 2012

By I. Nishkov, I. Grigorova, N. Valkanov, M. Ranchev

The processing of sulphide ores with variable and complex mineral composition and physical properties, such as those processed by two-stage selective flotation scheme in “Erma reka” concentrator, Minstroy Holding JSC, requires excellent selectivity in order to achieve acceptable concentrate grades. The lead-zinc ores from the hydrothermal lead-zinc deposits mainly contain galena (PbS), sphalerite (ZnS), pyrite (FeS) and chalcopyrite (CuFeS2), as well as non-metal minerals such as quartz, carbonates and clinopyroxenes skarns. One of the main impurities present in sphalerite is iron, which is known to be detrimental to the rate of sphalerite flotation and its recovery. The results from the conducted laboratory and industrial tests, presented in the previous study, showed that it is possible to depress the iron rich sphalerite by adding MINFIT® (modified sulfur-oxy depressant) at the pH of approximately 9.5 in rougher lead flotation circuit, leading to reduction of zinc sulphate consumption and complete elimination of cyanides from the flotation process. Furthermore, the consumption of copper sulphate, which reactivates the surface of the zinc minerals, was significantly reduced. Consequently, the optimisation of the reagent regime in the Erma reka concentrator, led to notably improved qualitative (grade, recovery) properties of the final lead and zinc concentrates. Moreover, when comparing the reagents consumption for 2014 and 2016 – when the processing plant have been applying the new optimized reagents regime, comprises the use of MINFIT as the primary depressant, the following results have been achieved: ZnSO4 decreased by 30%; CuSO4 consumption decreased four times and full rejection of cyanides from the process. Finally, this paper provides a state-of-the-art review of the obtained results during the period of application of the new flotation reagents regime in the Erma reka concentrator, Minstroy Holding JSC.

Jan 1, 2018

By Xiaolu Ye

"Comprehensive utilization of Bi and Sn from the tin-associated polymetallic tailings by “gravity separation – flotation combination process” has been studied, which was verified that the novel process is an effective method to deal with the high content pyrrhotite tin-associated polymetallic tailings. In this investigation, ore property analysis and magnetism analysis of pyrrhotite were conducted to research and develop reasonable beneficiation flowsheet. The results of ore property analysis present that pyrrhotite was not closely related to bismuth and tin minerals. Particle size analysis results indicated that pyrrhotite was mainly in the form of fine particles. The magnetic analysis results show that pyrrhotite was distribution in all the three types of pyrrhotite in a single mining area, which indicated that variable magnetism of with different crystal structure pyrrhotite. The process of “low intensity magnetic separation - high intensity magnetic separation” shown an excellent adaption for the high content pyrrhotite tin-associated polymetallic ore compared with the single flotation process based on the magnetism variable of pyrrhotite. The results of whole process test indicated that a bismuth coarse concentrate assaying 5.63% of Bi at 81.77% recovery was obtained, which treat the conditions for the Bi-S separation flotation. In addition, the content of sulfur in the tin concentrate decreased from 2.5% to 1.5%, which provided a new reference for other tin-associated polymetallic tailings. INTRODUCTION Tin has been applied extensively in catalytic chemistry, gas sensors, tin plating, and plumbing. Tin-bearing polymetallic ores have been the important deposit types to recycle tin with the rapid depletion of mineral resources. The comprehensive utilization of the associated elements has been a preoccupation for the mineral processing researchers."

Jan 1, 2018

By Cheng Xiang, Nan Ye, Xinyuan Ke, Yang. Jiakuan, Huabin Wang

Bayer red mud is a highly alkaline residue produced by the alumina industry through the Bayer process. Its disposal is a worldwide problem. The high alkali content and poor pozzolanic activity is aconstraint for its utilization on construction materials. In this study, the red mud was activated through an alkali-thermal method to improve its activity so that it can be utilized in geopolymerization. The red mud was mixed with different amounts of sodium hydroxide, and calcined under 800 °C to produce geopolymer precursors, and then mixed with water directly to prepare one-part geopolymer. X-ray diffraction was conducted to study the phase transformation of red mud and the mechanism of its geopolymerization. Nitrogen Isothermal Adsorption tests were conducted to analyze the pore structure of the geopolymer binders. The results show that calcinations with alkali would promote the Al in red mud transforming into glassy SiO2 to form the N-A-S phase which is soluble in water. When the red mud was calcined at 800 °C with a Na2O addition more than 10%, the dissolving of Si and Al from red mud was greatly improved. The thermal-alkali activated red mud with 10% Na2O obtaining a compressive strength of 9.77 MPa after it reacted with water and cured for 7 days at 20 °C and 95% RH. But the strength decreased as the curing time extended to 28 days. The reason is suggested to be that the polymerization of Al-O and Si-O is unstable due to the low Si/Al ratio of red mud. The alkali in the structure dissolves again into the pore water and corrupts the pore structure. Therefore, the thermal-alkali red mud should be combined with other reactive aluminosilicate materials such as granulated blast furnace slag to absorb the alkali released by the thermal-alkali red mud at the latter curing days.

Jan 1, 2014

By G. G. Xiong

Water-sealed cyclone is a new efficient equipment to use for grading,concentrating of slurry, it was researched and developed by the Kunming Metallurgy Research Institute in the 1980s , and ac-cessed to the 1990 national invention award and the national patent products (ZL02245313.X ). The equipment and technology are innovative, firstly, we design a set of micro-pressure (0.005~0.008MPa) water-sealed device, which eliminates the gas phase of three-phase of sol-id-liquid-gas of the traditional general hydrocyclone grading process, it only has solid and liquid phases. Secondly, the axial velocity envelope surface which is a factor of controlling the accuracy of grading changes to a wedge rotation; and the interface of upward flow to down flow changes from surface to the solid, it can improve grading accuracy. Thirdly, water-sealed box and catheter devices make the stilling which pass through the cyclone cone centrifugal force fields re-enter the pressure grading zone of catheter. The three innovations make water-sealed cyclone can reduce the loss of overflow and has less mud in stilling product. Because the excellent performance, the water-sealed cyclone has application in non-ferrous metals, ferrous metals, non-metallic and aluminum hydroxide industries for grading, desliming and concentrating since it has successfully developed.

Jan 1, 2014

By Abhakumari

Effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. Effect of the magnitude of electrolytic currents on the activity and growth of bacterial cells was studied. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and bio catalysis of anodic oxidation.

Sep 1, 2012

By D. H. Xiong

Low grade oxidized iron ores are usually not economic to utilize. However, the development of SLon magnetic separators and other new technologies make the process cost lower and lower. In this paper, several low-grade oxidized iron ore process flowsheets are introduced. The key procedure is that at the early stage, SLon magnetic separators are applied to discharge as more tails as possible with very low cost, only a small portion of rough concentrate going to the cleaning stage, showing the new technologies are profitable for such iron ores.

Jan 1, 2014

By X. Q. Chen

According to the different characters of the middle-low grade bauxite, based on the normal flotation & reverse flotation technology, the author innovates the new technology which is named bi-flotation, it integrates the advantages of normal flotation & reverse flotation, while avoids their disadvantages. Take Henan middle-low grade bauxite as research object, according to the pilot experiment of bi-flotation technology, the concentrate A/S is 9.37 and the recovery of alumina is 80.18% by flotation separate the raw ore which A/S is only 4.19.

Jan 1, 2014

By V. I. Lakshmanan

The growing concerns on process efficiency, escalating operating and capital costs along with environmental and social concerns of using conventional technology for extracting gold and titanium dioxide demand an in-depth understanding of the fundamentals and a broader understanding of the various process steps involved. This will allow development of efficient process flowsheet for product recovery and compliance with regulatory guidelines. This paper will discuss our recent developments in mineral processing and hydrometallurgical technologies to recover gold and titanium dioxide from a wide range of feed materials including ores, concentrates and tailings.

Sep 1, 2012

By J. Leite

In a small-scale mining in Brazil?s northeast, scheelite were exploited since 1940?s using a traditional gravity concentration flowchart (composed by jigs and shacking tables) that operates with low efficient for fine particles. Tailing of this plant was submitted to chemical, mineralogical and size characterization. Results pointed 50% smaller than 74µm with a grade of 0.11% WO3. The particle?s size is an important operational variable to heighten recuperation by shacking tables. Tests using Falcon SB40 centrifuge concentrators and shacking table were realized, optimizing their operational variables. Based on the tests results a new flowchart was proposed for concentrating and tailings recovery.

Sep 1, 2012

By V. A. Chanturiya

There is an obvious disproportion in Russia gold-mining industry between the structure of gold reserves and the gold-mining techniques. The bulk of gold (over 70%) is extracted from alluvial deposit, 20%~25% from bedrock occurrences and 5%~7% from complex copper-zinc and polymetallic ores. The proved gold-bearing reserves are distributed as follows: alluvial ?19%, bedrock ?80%, the latter being sufficient to supply gold at the current production level for 100 years to come. In Russia, like elsewhere in the world, development of primary gold deposits is considered a first-priority line of development for gold-mining industry. Most of the gold-containing ores characteristic of Russian gold deposits are resistant ores with gold content varying between 3 ppm and 5 ppm usually showing quite low gold and silver recovery by cyanidation. Processing resistance of gold-containing mineral complexes is related to the presence of gold particles of submicrometric (<1.0 µm) and nanometric (10~100 nm) size, mostly asso-ciated with pyrite and arsenopyrite. Therefore switching over to processing bedrock entails a num-ber of technological problems that stem from chemical and physical resistivity of ores. The chemical resistivity can be overcome through flotation, oxidation roasting, autoclave leaching (biohydro-metallurgical oxidation), etc. The physical resistivity can be dealt with by resorting to traditional power-intensive methods,e.g. grinding to a ?40µm size, thermal treatments of sulphide concentrates and non-traditional high-energy methods of liberating the sulphides by means of power attack, e.g. electro-chemical oxidation, exposure to electron beam radiation and other methods. The modern non-traditional processes for treatment of rebellious noble metal-bearing ore, aimed at improving disintegration efficiency for finely dispersed mineral complexes are analysed. Advantages and perspectives of a new high-efficient, energy-saving and ecologically safe process of the nanosecond high-power electromagnetic pulses (HPEMP) effect are proved. The said process provides a stable increase in the valuable component recovery at lower energy consumption and production costs of the finite product at the stage of dressing rebellious gold-bearing ores and concentrated products. The experimental data prove high efficiency of the preliminary impulse treatment, thus, the increase in the gold recovery at the cyanidation stage amounted to 4%~12% from rebel-lious ores, 10%~30% from gravity concentrates, 5%~45% from flotation concentrates, 30%~80% from oil flotation tailings.

Jan 1, 2014

By V. V. Morozov, I. S. Barmin, A. V. Tugolukov, V. V. Polivanskaya

"It was presents the results of research on improving reagent regime and scheme of enrichment of slime classes of Apatite-Staffelite ores and tailings stockpile of Kovdorsky enrichment plant. It was investigated the regularities of flocculation in the processes of thickening and selective flotation apatite-bearing ores. It was established character of the influence of flotation reagents on the flocculation process. It was shown that the sodium silicate and soda ash have a stabilizing effect by thickening of sludges. Neonol and oleic acid have a coagulating or flocculating effect. It was tested the new regime flotation, involving an initial conditioning with using of reagent - dispersants before feeding the pulp into the flotation and subsequent conditioning with reagents having a coagulating effect. The flowsheet and reagent regime for enrichment of fine-grained tailings stockpiled was developed, which providing production of standard apatite concentrate and increasing the recovery of valuable components. There are presented results of the research of activities of strong organic surfactant on solubility of colloidal form fatty acid collector and aggregate stability of fine minerals in the process of thickening and flotation. Surfactants such as Neonol have been investigated for increasing the activity of the collectors. When using the process of thickening sludge fraction with flocculant Praestol 2540 and stadial conditioning of sludge were obtained concentrates containing up to 38.1% P2O5 at recovery. INTRODUCTION A feature of the Apatite-Staffelite ores of the Kovdorsky deposit is the presence of a large number of fine mineral particles and a reduced hardness of phosphate minerals (Beloborodov et al., 2010, Tugolukov et al., 2012). Formed in the ore-preparation process, sludges are lost with a discharge in the thickening operation. Sludge is characterized by an increased content of phosphorus pentoxide (P2O5). Losses of P2O5 at enrichment of the stale tailings of Kovdorsky GOK reach 14.0%. The high losses of P2O5 caused a profound study of the behavior of thin apatite classes under conditions of thickening and flotation."

Jan 1, 2018

By W. H. Yong

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores, whereas oxidized molybdenum ores have not been exploited and utilized efficiently. The aim of this article is to study the applied mineralogy of an intergrown iron-molybdenum oxidized ore in order to provide a mineralogical basis for the ore beneficiation research. The ore occurred in a surface oxidized zone seam and contained 23.65% Fe2O3 and 1.58% Mo. Various characterization techniques were employed to study the chemical composition and mineral composition of the ore, the particle size distribution of the minerals in the ore, and the tex-ture and structure of the ore. The results showed that the iron-molybdenum ore occurred in a wet, soft and earthy state. The ore was composed mainly of several oxidized minerals and colloidal min-erals, including wulfenite, barite, limonite and quartz. Wulfenite was one of the major and stable components in the ore and occurred as a separate mineral. Wulfenite, barite and quartz were granu-lar minerals with particle size ranging from fine to coarse but mainly in the fine particle range. Li-monite showed a crust and honeycomb-like colloidal state and composed the framework in the ore for the formation of the other minerals. They filled the pores in the framework and the size of the pores affected the size of the minerals formed in the pores and hence the recovery of wulfenite in ore beneficiation. According to the applied mineralogical properties of the oxidized molybdenum ore, a promising ore beneficiation process was proposed as follow Magnetic separation should be carried out first to separate the magnetic iron minerals and then the molybdenum mineral will be recovered by gravity concentration or a combination process of gravity concentration and flotation, depending on the distribution of the molybdenum mineral in the product of the magnetic separation.

Jan 1, 2014

By H. D. Yu

In this paper, an evaluation about the process mineralogy of the rich iron mine in Mongolia with comprehensive methods is given; this provides foundation of the comprehensive recovery of iron and cobalt in the ore. The research shows that the iron?s grade is 61.23%, Co?s grade is 0.02%, the ore is rich iron ore and its Co content also reaches border mining grade. For the ore, if want get high grade iron concentrate powder, must identify the mineral composition and the occurrence of iron and take into ac-count the recovery of Co content as associated resources. Chemical phase analysis results show that 86.35% of iron exists in magnetite, which means that the theoretical recovery ratio of iron is close to 86%. Minerals spectrum analysis confirmed that the magnetite containing a small amount of Mg, Al, and other impurities, the actual iron minerals to 70.28%, which means that theoretically iron grade iron concentrate only close to 70.28%. Based on the result of iron chemical phase analysis, by investigating the liberation of sulfide minerals and gangue, the recovery index of iron can be forecasted, when grinding fineness is 35%, 45%, 55% and 65% bellow 0.074mm,theoretical content of Fe in iron concentrate separately is 67.71%,67.88%,68.78%,and 69.43%,accordingly the theoretical recovery of Fe is 87.38%,87.05%,86.92% and 86.63%. From the perspective of process mineralogy, the forecast mineral beneficiation indicators show that the ore is easy sorting ore, iron processing operations have higher recovery rate, but wants sorting of high-grade iron ore concentrate still need appropriate grinding fineness. Furthermore, associated element Co, existing mostly in pyrite and pyrrhotite, is valuable in the ore. Pyrite and pyrrhotite have ideal liberation under grinding, so cobalt can be easily enriched in sulfide concentrate.

Jan 1, 2014

By K. S. McClure, S. B. Chitralekha, R. B. Gopaluni, Chmylek. T., S. L. Shah

This is a tutorial paper on industrially successful approaches for nonlinear process monitoring. Online process monitoring is essential to continuous operation of plants at high efficiency. The problem of process monitoring is one where an impending but undesirable process condition has to be identified and used to alert process engineers. This problem has traditionally been solved by practicing engineers using statistical techniques that detect a change in the underlying correlation structure of process variables. For linear correlation structures, algorithms such as principal components analysis, independent component analysis and partial least squares have been proposed. However, many industrial processes exhibit nonlinear correlation structure between the process variables. In this tutorial we describe various nonlinear monitoring techniques and elaborate on two recently developed methods, namely Support Vector Machine and Local Linear Embedding. The two methods are evaluated by application on two experimental case studies, a SAG mill and a polymer extruder.

Jan 1, 2014

By Ali Dehghani Ahmadabadi

Gravity separation technique is widely used in mineral beneficiation practices for its low cost, ease of operation, and eco-friendly nature. The most commonly used gravity methods for beneficiation of iron ores are shaking table, jig and spiral methods which aren&apos;t very effective for iron mineral fines. Multi-Gravity Separator (MGS) is suitable for the treatment of fines with a maximum particle size of approximately 500 µm. This study was performed on a low-grade haematite iron ore from Chadormalutailing dams. Detailed mineralogical, physical and chemical characteristics of a goethiticlateritic iron ore showed that the sample contained porous and friable oxides and hydroxides of iron. The ore sample had a feed grade of 35% Fe, 1.1% FeO, 15.5% SiO2 and 8.5% Al2O3. Haematite and goethite are the main iron-bearing minerals while quartzite and kaolinite are the major gangue mineral constituents. In this paper, the statistical evaluation and optimization of grade and recovery using a factorial design of experiment (DOE) method has been carried out for Chadormalulow grade ultra-fine haematite tailings with MGS. The input process parameters considered are drum speed, tilt angle, wash water flow rate and pulp density. The results show considerable improvements in both the quality characteristics such as grade and recovery with statistical evaluation and optimization, compared to the initial value of grade and recovery. Keywords: multi-gravity separator, mgs, statistical evaluation, optimization, haematite

Sep 1, 2012

By Abhilash

Different methods of utilizing refractory bauxite and disposing red mud are practiced throughout the world, but none of them are known to be environmentally innocuous due to the complexity and /or high cost, and none has been found to be feasible on an industrial scale. Under these conditions, the use of bioleaching process seems promising. The present study emphasizes on the isolation of native extremophiles from the source Indian bauxite and red mud, with their detailed cellular and physio-chemical, and biochemical characterization. These organisms were tested for their ability to thrive in physically or geochemically extreme conditions. The gram positive capsule rich mesophiles and thermophiles were tested for removal of gangue minerals from the bauxite and red mud samples. Keywords: refractory bauxite, red mud, extremophiles, bio-beneficiation, gangue

Sep 1, 2012

By V. V. Ramarao

Grinding and flotation operations deliver better-optimized performance when they are monitored and controlled in terms of the minerals they process rather than as elemental assays that we usually refer to. Mesh of grind (MoG), liberation, floatability, grade and recovery etc. are more directly related with the minerals and their characteristics rather than the elemental assays. Hence, online analyzers only provide the status for the grade and recovery of metals and not the direction for the enhanced performance. Central Research and Development Laboratory (CRDL) and Rampura Agucha Mine (RAM) mill section of Hindustan Zinc Limited (HZL) jointly undertook various survey campaigns in the grinding and flotation process streams. Grinding circuit surveys involved systematic collection of representative samples from different grinding circuit streams under stabilized conditions for monitoring particle size and process mineralogy details across individual grinding circuit. Flotation survey campaigns included study of fort-nightly / monthly composites of un-ground flotation feed, lead concentrate, lead tailing, zinc concentrate and final tailing samples for size distribution details in the 150 ? 38 micron range, chemical analysis and mineral characterization through optical microscope. This work details the investigations results and their implications on beneficiation performance. Grinding circuit survey campaigns supported the task for modifying the originally installed configuration of hydrocyclones, to limit recovery losses due to excess grinding of soft galena and related silver minerals. Flotation plant surveys helped in adjusting flotation circuit process parameters to reduce loss of liberated and floatable galena and sphalerite grains into their respective tailing streams. Keywords: grinding circuits, survey campaign, hydrocyclones, mineral liberation and locking, lead-zinc ore beneficiation operation

Sep 1, 2012