Search Documents

By P. Harris, D Bradshaw

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003

By K. Saberyan

Zirconium and hafnium are two important elements in nuclear industries. Zirconium is used in fuel rod for its low neutron absorption. Hafnium should be separated from zirconium, because it has higher neutron absorption cross section. In this research, separation process of the mentioned elements from (Zr+Hf)Cl4 mixture produced in the Zirconium production plant (ZPP) of Iran (Esfahan) was studied employing solvent extraction method in the nitric acid medium by using tributylphosphate (TBP) as solvent, and kerosene as diluent. The effects of nitric acid, sodium nitrate and amount of extractant, zirconium concentration in aqueous phase, phase ratio, agitation time, and mixer agitation rate were investigated on the separation process. The process was optimized at 5 M nitric acid, 1 M sodium nitrate, 60% (v/v) TBP. The optimum values for phase ratio, agitation time and agitation rate were 1.5 min and 500 rpm respectively. In this condition, the zirconium extraction efficiency, and separation factor were 65.1% and 205.59, respectively. Finally, we accessed to nuclear grade in this research.

Jan 1, 2014

By M. Evertsson, E. Hulthén

"In aggregate production and mining the operators are responsible for controlling and monitoring the process to maintain high plant throughput and safe operation. Operators have to make different decisions to control the process due to changed demand on the operation from both management and conditions of the process. The quality of the response and the time it takes for an operator to respond to altered demand relies on what information is available and the experience of the operator. In this work a dynamic simulation platform has been developed to be used for operator training. Models for representing production units and process control for plant simulations have been developed and implemented in MATLAB/SIMULINK to simulate time-dependent plant behavior. Stochastic and scheduled events are included using the discrete events simulation toolbox SimEvents. The human-machine interface was developed using the human-machine interface software ICONICS. The operators’ cognitive process, in interpreting the plants semantic, has been studied by observations and with informal interviews with operators. This was done to get information about the daily operation and the problems that occur in the process. By interacting with operators that experience different physical interactions with the process; more qualitative e-learning software for supporting operator training in a dynamic operator environment could be developed. The quality of the operator training environment was evaluated with a usability study that was performed with operators and others within the production."

Jan 1, 2014

By M. Wright, A. H. Mwale

This paper examines the combination of unit technologies in a minerals beneficiation train, and explores the inter-relationship between energy input and water consumption for a given mineralogy and product recovery, as these are two critical environmental issues which affect the overall viability of many minerals plants. In particular, we review constitutive relationships for each of the sub-processes of comminution, flotation, and tailings dewatering, and suggest how these might be integrated into a unified hybrid model, with particle size distribution as the key design variable. Such a model can then be used to explore the trade-offs between different performance objectives (be these technical, economic or environmental) as part of a multiple-objectives optimisation exercise. In this way, it may become practical to envision situations in which concentrate grade and recovery are sacrificed, marginally, in order to reduce energy demand in comminution, and improve overall water recovery. This becomes more relevant as the industry commits to advancing the sustainable development agenda in the face of the increasing life -cycle costs and impacts of minerals processing operations, coupled to declining ore body grades, and the desire to maximise recovery of minor and trace elements. Some specific observations for copper are offered.

Jan 1, 2003

By Rodolfo Silva, Antonio Peres, Afonso Martins, Gilberto Ramalho, Mario Cabello

The consumption of aggregates in civil construction has increased considerably in Brazil for the last years. The extraction of sand and gravel generates significant environmental impacts. As the quarries and sand deposits are getting exhausted near the big cities, the price of aggregates is increasing. Meanwhile, the extraction of quartzite (dimensional stone) in the state of Minas Gerais has been done mostly in small quarries, with very low recovery, generating approximately six million tons of wastes a year, which causes pollution, increases final prices of products, decreases the life time of quarries and ends up in the closure of enterprises. The government agencies and the quarries’ owners understand that only by finding applications to wastes there will be development to the sector. The aim of this investigation was to study the application to the quartzite wastes as aggregate in the civil construction. Samples of quartzite wastes collected in a quarry were characterized by petrographic analyses. Laboratory tests of crushing and grinding were done to analyze the viability of reducing the size of coarse material to a finer one to be used as raw material in industrialized mortars and concrete pre-molded components.

Jan 1, 2014

By Henrique Kahn, Daniel Uliana, Juliana Antoniassi, Viviane Shimizu

"Mineral exploration and geometallurgy require a large number of samples for physical, chemical and mineralogical assays. The combination of all these data and their spatial distribution define the ore variability. This is important in exploration programs and crucial in feasibility studies as well as at the production operation level. Ore mineralogical composition and its associations, characterizing the geological formation and mineralization, are the main keys to define the ore domains and its variability, which can be quickly assessed by cluster analysis and by modern automated mineralogy tools. One hundred and ten copper ore samples from Sossego mine, in Brazil were compared and classified by X-ray diffraction cluster analysis based on the position and the intensity of the diffracted peaks. Initially four ore types were categorized based on content of major minerals: quartz, feldspar, amphibole, iron oxides, mica and chlorite. Results showed a strong correlation between the grouping and the samples location in Sequeirinho and Sossego orebodies, with a straight link to types/intensities of hydrothermal alteration prevailing in each body, which reflects the mineralogical composition and thus the X-ray patterns. Samples from four recognized ore types were submitted to detailed automated mineralogical studies by electron beam image analysis and differ strongly from each other regarding their chemical and mineralogical compositions and relevant parameters for mineral processing. Chalcopyrite is essentially the only valuable mineral, occurring both as submillimetric grains included in other minerals and as larger crystals. Except for pyrite, other sulfide minerals occur as traces. Chalcopyrite liberation curves indicate that samples from Sossego have higher liberation degree than those from Sequeirinho. The proposed method proved to be very efficient and accurate to classify a large number of samples within a short time frame, allowing the distinction of the ore types regarding their mineralogical composition as well as the mineral processing parameters."

Jan 1, 2014

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By Chen Zhiqiang, Luo Chuansheng, Chen Ziqiang, Liu Jianguo, Rao Jinshan

To comprehensively utilize the valuable resource in tailings, increase the economic benefit of mine, reduce the amount of tailings, prolong the service life of tailing dam, the comprehensive utilization of tailing resource is arousing the attention of more and more mines. Research of comprehensive recovery of feldspar and silica from Cu-Mo floatation tailings has been furthered. Technology of "De-sliming-Magnetic Separation-Reverse Flotation-Feldspar and Silica Separation" has been developed to utilize the resource. Slime is removed and reagents cost is reduced by de-sliming. The specific effective collector ZL is used in gangues reverse flotation, and GZ-818 is the collector in feldspar and silica separation. The grinding operation is vital to ensure the liberation degree of feldspar and to eliminate the reagents pollution on minerals surface. To a Cu-Mo flotation tailing assaying K2O 5.22%, Na2O 2.22%, Fe2O3 1.95%, Al2O3 12.05%, SiO270.66%, superfine K-feldspar and silica concentrates can be produced. The feldspar concentrate productivity is 29.67% assaying K2O 8.99%, Na2O 2.86%, Fe2O3 0.16%, Al2O3 16.99% and SiO2 68.92%. The silica concentrate productivity is 14.20% assaying 0.17% K2O, 0.04% Na2O, 0.01% Fe2O3, 0.55% Al2O3 and 98.17% SiO2. The technology provides technological reference model for the similar mines.

Jan 1, 2014

By Luis Bergh, Francisco Díaz, Isabel Panire, Juan Yianatos, Luis Vinnett

"In this paper, industrial data of residence time distribution (RTD) in mechanical flotation cells is presented, which were measured in several plants using the radioactive tracer technique. Results include mechanical flotation cells of 100 - 300 m3, which were operated with effective residence times from 2 to 7 min. Tests were developed in forced air and self-aerated cells for liquid and solids (non-floatable) per size classes. Different RTD model structures including perfect mixer, Large and Small Tanks in Series (LSTS) and by-pass flow plus perfect mixer were evaluated and compared for single cells. The actual mixing regime was related to the effective residence times and cell designs based on the model fitting. By-pass flow percentages were typically lower than 10%, therefore the perfect mixer model plus a dead time was a suitable model structure in most cases. On the other hand, the arrangement of cells in series was effective in reducing the bypass flow observed in single cells (by-pass flow percentage greater than 5%). In addition, the N perfectly mixed reactor in series model was used to represent the mixing regime along flotation banks, which were operated with mean residence times in the range of 18 - 53 min. Results showed that N tanks in series plus dead time were closer to the actual values in most cases."

Jan 1, 2014

By Christopher Greet, Alfred Van den Bosch

"A range of media alloys with different chromium content has been developed for different milling applications. When selecting the grinding media alloy for a specific application, consideration must be given to the mineralogy of the ore as well as the water chemistry and mill operating conditions. The paper describes the influence of the microstructure of the alloy on the wear resistance and the influence of the chrome content on the pulp chemistry and downstream processing. It also provides information about the in-house tools which Magotteaux have developed to predict the media wear rate with different chromium content alloys and predict their flotation efficiencies that can be expected when the right alloy is selected for a particular application."

Jan 1, 2014

By Nicolus Rotich, Ritva Tuunila, Louhi-Kultanen. Marjatta

Most minerals, their ores, and gangue require sorting in order to maximize the recovery of the primary product during concentration. Gravity separation though old, is not obsolete and is continually playing an important role in mineral processing and many other industries, especially where plant energy efficiency is of concern. Screen designs e.g. material of construction, deck angle of inclination, the feed throughput, and physical as well as chemical properties of the particles, are critical factors to consider when using gravity for solid separation. Solids loading and screen geometry are significant, and easily manipulated operational parameters that affect both the screening rate and efficiency to a large extent. In this paper we applied nonlinear least squares optimization technique, and response surface methodology first, to assess the significance of the two factors, and secondly to select the best mathematical models that optimize both capacity and efficiency of the screening process. Initial experiments and confirmation tests were conducted on a prototype screen of 846.51cm2 effective area, (2100 cm2 total area). For glass beads of sizes 0.75-3mm, with feed loads of 10g up to 160g, and inclination angles from 5-20o, a maximum efficiency of 66.7%, and a screening rate of 22g/s was achieved with a screen loading of 86.5g, and an inclination angle of 12.43o. These results were then subjected to nonlinear least squares optimization, in which afterwards an optimum theoretical efficiency of 72% and screening rate of 31.2g/s were achieved at a loading of up to 104g. There was excellent performance at angles 12.5=?=17.5, but poor at the angles outside this range. The screening efficiency did not seem to respond significantly to changes in screen loading. Confirmation tests conducted at selected optimum parameters achieved an efficiency of 72.1% (at 17.5o with 88g load), and a rate of 27g/s at 16.5o with 104g.

Jan 1, 2014

By Graeme Lane, Yuqing Feng, Kaixi Jiang, Junwu Zhou, Zhengchang Shen, Tao Song

"Airlift reactors are used in a wide range of industries, such as hydrometallurgy, biochemical processes, chemical process industry and waste water treatment. With increasing superficial gas velocity three circulation regimes can be defined: no gas bubbles in the downcomer, gas bubbles remain stationary in the downcomer and gas bubbles in the circulating regime. In this paper a numerical modelling method was presented for gas-liquid flow in airlift reactors under different bubble recirculation regimes. Gas-liquid flow was modelled using the Eulerian two-fluid equations, and extra user defined subroutines were incorporated to consider the complex physics, such as bubble induced turbulence and turbulent dispersion force. Some alternative correlations of drag coefficient were used to capture the bubble distributions in the riser and downcomer of the airlift reactor, with consideration of the interaction between bubbles. As using constant bubble size is hard to describe global characteristics of the flow in airlift reactors for three circulation regimes, a model including multiple bubble sizes was presented to get more accurate simulation results of gas holdup and water velocity. Also, the inhomogeneous MUSIG model was used, as an exploration, to compute the complex flow regimes. The MUSIG model is a population balance method to predict the bubble sizes, taking break-up and coalescence into account. The modelling method was applied to a laboratory internal loop airlift reactor, and the simulation results were compared with the experimental measurements of Simcik et al. (2011) for gas holdup and water velocity. The three bubble circulation regimes were observed from simulation figures. Reasonable agreement was obtained over a range of operating conditions, and an improvement was demonstrated using the proposed methods."

Jan 1, 2014

By Frank van der Meer, Lea Quincke

"High Pressure Grinding is applied to achieve size reduction of the particles by inter-particle breakage and to generate micro-cracks in the product particles as a contributing factor in e.g. leaching or mineral liberation. As alternative to classification, a closed circuit operation for HPGR can be established by product recycling, where a proportion of the coarser edge material and parts of the center material are split-off to be recirculated to achieve a finer final (center) discharge product for subsequent processing steps as ball mill grinding or beneficiation. As a result of the product recycling, the content of fines in the feed material increases and may affect the grinding efficiency in terms of production of fines and the generation of micro-cracks in the particles. In the scope of this paper, the effects of the proportion of fines in HPGR feed on grinding efficiency and micro-crack generation were evaluated. Grinding tests were executed with different feed size distributions, from a fines-void situation (truncated feed) to a fines-abundant situation (high product recycle). The evaluation of grinding efficiency and generation of micro-cracks was done by particle size analysis, Bond Work Index tests, impact tests on HPGR feed and products, and X-ray computed tomography of single product particles. This publication summarizes the main aspects of the outcome of these investigations."

Jan 1, 2014

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By Nóra Schreithofer, Zoltán Jávor, Kari Heiskanen

"One of the challenges the mineral processing industry is facing is caused by the fact that water resources in mining areas are becoming very limited and the cost of water is increasing. The water sources in arid regions often have high salt content. Environmental regulations are forcing plant operations towards completely closing the water cycles within plants. This means that impurities (salts, reagents, ions dissolved from minerals, etc.) accumulate within the circuit that will affect the flotation performance. Water purification can significantly increase the operating costs therefore it should be carefully considered weather the impurities need to be completely removed or is there a tolerable level of impurities that can still be left in the process water without significant deterioration of the flotation performance? Several additional questions arise: what are the tools that help identify what is a tolerable level of impurities? How do the different impurities interact and what is their effect on the process? The effect of frothers on the dynamic properties of air/liquid interface in different size-scales has been extensively studied by the authors in the past. Based on these studies a frother characterization framework was developed that systematically examines the dynamic surface properties of the air/liquid interface in relation to the bubble size. This work can be considered as tool that could be used for the above mentioned purpose. The present study investigates weather the same frother characterization framework can be applied for systems where both frother and different types of salts are present. Nasfroth 240 was used as a frother, in combination with structure-breaker KCl or structure-maker NaCl and CaCl2. Bubble size measurements in laboratory scale mechanical flotation cell and laboratory flotation column and dynamic surface property measurements (dynamic surface tension and dilatational elasticity) were performed. The results highlighted the addition of salt to the frother solutions significantly decrease the bubble size and increase the froth high. The coalescence behavior of bubbles showed correlation between the D32 and ionic strength of salts. The results highlighted that the studied structure maker and structure breaker salts effect the dynamic surface properties in different way."

Jan 1, 2014

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By P. Somasundaran, Tarun Bhambhani, D. R. Nagaraj, P. Patra

"Certain non-sulfide gangue minerals are known to have a detrimental impact on flotation performance. When present in large amounts, they can negatively affect recoveries, grades and throughput at current operations, and dictate the viability and economics of a greenfield project. While the problem has been investigated for a long period of time, a scientific understanding of the mechanisms by which these minerals affect performance has not been obtained, and no acceptable solutions have been developed. This study focused on the role of physical aspects (e.g. shape, size and morphology) of these minerals as the underlying factors for poor performance. Flotation tests were conducted using model mineral systems to understand the impact of one phyllosilicate mineral (muscovite) on flotation kinetics, recoveries and grades. The study reveals that there is minimal impact on flotation kinetics, no impact on recoveries, but a very strong detrimental impact on concentrate grade. The traditional mechanisms of transport such as true flotation and entrainment are not sufficient in describing the extent of transport. The transport is attributed to the unique platy morphology of muscovite, which allows for action of buoyancy forces. Data also shows that the muscovite transport to the froth phase depends on particle size; coarser sized muscovite (100-150@) report to the froth phase in much larger amounts than medium sized muscovite (50-100@). At finer size fractions (<50@) the transport is also increased, and this is likely due to entrainment."

Jan 1, 2014

By K. H. Luo, J. Y. Liu

An experimental study on interparticle breakage of three iron ores was carried out by compressive stressing of particle-bed in a piston-die device. The feeds to the particle-bed stressing were five narrow size fractions in the size range of 0.2~3.2 mm respectively and a wide size fraction of 0/4.0 mm. The pressures applied were in the range between 30 and 360 MPa. The results show that the energy absorption of the particle bed increases linearly with the pressure; the increase of the product fineness with the pressure declines as the pressure goes up; and the product size distributions resulting from interparticle breakage of different narrow size fractions have no self-similarity. Using data obtained from the piston-die compressive stressing test, the suitability of a previously-developed material-characterization model for interparticle breakage was verified for these ores. It is shown that the particle-bed compression test conducted with piston-die device in lab-scale may provide a cost-effective way of studying and modelling size-reduction of ore materials by interparticle breakage.

Jan 1, 2014

The air recovery from a flotation cell is the fraction of inlet air which overflows the weir as un-broken bubbles. The air recovery is an important factor in froth phase phenomena; such as gangue entrainment and froth recovery. Increasing the air recovery, results in a higher recovery of attached mineral particles. Air recovery can be measured experimentally on plant using image processing of the top surface of an overflowing froth. The air recovery is directly linked to froth stability and the bursting rate of the bubbles at the froth surface, making it very difficult to predict. Experimental results show a very strong correlation between the superficial velocity of the inlet air and the superficial velocity of the air leaving the cell through the froth surface due to bursting, calculated from the experimentally measured air recovery. This correlation holds over multiple banks from different plants. Development of a power law equation around the inlet air velocity and the bubble solids loading on the froth surface allows the superficial air velocity through the top surface of the froth to be predicted, and from this the air recovery. This model is valid for use when operating beyond the peak in air recovery.

Jan 1, 2014

By I. Govender, M. C. Richter, N. Mangadoddy

"We present an analysis of trajectory and time averaged data of near gravitational material (NGM) representative coal tracer particles within a magnetite medium passing through a 100mm diameter hydrocyclone imaged with PEPT (positron emission particle tracking) at iThemba labs, Cape Town. The tracking of neutrally buoyant tracers as well as the other NGM allows an empirical study of the approximate dynamical behaviours of both the dense medium as well as the range (size and density) of particles around the separator’s cut size within a partially imaged volume of the cyclone body lying within the field of view of the detector. The study was commissioned as part of a CFD validation study using empirical data from a real-world lab-appropriate system in order to shed light on the inner workings of hydrocyclones and their separation mechanisms. We employ various optimisation and noise reduction techniques within the analysis and follow a detailed investigation of the velocity fields derived from the raw spatial positions with an emphasis on the velocity profile within the forced and free vortex zones. Challenges encountered with this high velocity particle tracking experiment within a highly attenuating environment are also discussed. Various important velocity distributions are shown and compared to theoretical predictions. The power law decay profile of the free vortex and radial velocity scaling with regards to the Froude number are reproduced in line with the static particle approach. INTRODUCTION Cyclones have long been a vital industrial tool for the separation of different classes of particles. These cyclonic separators (with either gas or liquid medium) operate by forcing the solids-bearing fluid at high pressure into a cylindrical vessel causing high tangential velocity fluid rotation as well as, in the case of an “open” (with exit channels open to the atmosphere) cyclone, a central vortex air column spanning from underflow to overflow exit. The fluid is forced to exit the cyclone at two locations, the spigot and the vortex finder, generating the underflow and overflow respectively. The body of the cyclone usually terminates in a conical shape to focus the underflow stream. This geometry and large incident fluid velocity force high density materials toward the wall of the vessel where they are most likely to move along and down the inside wall away from the inlet to exit via the underflow while lower density materials traverse the cyclone body closer to the central vortex and are buffeted by the upward-moving column towards the overflow exit. This separation mechanism is selective of density and size in an interplay between the centrifugal force due to the rotation of the fluid and a drag force acting on the particles."

Jan 1, 2018