Search Documents

By A. R. Videla, P. R. Brito-Parada, I. Mackay

"Linking results from laboratory scale experiments to industrial flotation behaviour is challenging. Typically, such experiments involve batch tests in which the system does not operate at steady-state, making it difficult to infer the effects that operating conditions have on flotation performance. In order to overcome this limitation a 4-litre recirculating tank was previously developed at Imperial College London. This tank is capable of reaching, and operating at, steady-state by recycling overflowing concentrate back into the feed. As well as instruments to control operating conditions, it is fitted with a system of sensors that allow the surface of the froth to be dynamically monitored. From this information, it is possible to measure the air recovery—a proxy for froth stability. Thus, this bench-scale tank can be used to understand the effect of differing operating conditions on flotation performance at steady state. However, so far, this cell has only been used to investigate idealised systems with only one or two species.Reprocessing of tailings dams is not only environmentally desirable but also increasingly economically feasible due to the declining head grades of primary deposits. There is also the added benefit of no further milling being required prior to flotation. However, the effects of fine and ultrafine particles on froth stability are not yet fully understood. In this work, the bench-scale continuous tank has been used for the first time to determine the flotation response of a complex feed, consisting of samples from a copper tailings dam, to changes in operating conditions. It was shown that the froth stability in the system is comparable to that of previous work and industrial tests, with a peak in air recovery being found at a superficial gas velocity of 1.13 cm/s. There is scope to optimize the froth stability of tailings flotation for enhanced metallurgical performance."

Jan 1, 2018

By Vincent C. Smith, Agit Singh, Bernard Muller

The control of minerals processing plants is by no means trivial. In order to address some of the difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written to test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimising algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. The controller was tested for various scenarios that are often encountered in the minerals processing industry. When problems were encountered, the MPC algorithm was specially adapted to accommodate for these difficulties. Control was further improved by using feedforward control as well as quadratic programming. The movement of the manipulated variables was reduced by using a region of uncertainty that allows the controlled variable to vary within a specified region around the setpoint. Integrators were handled by adapting the algorithm slightly and adding an optional integral error portion in the MPC controller. The performance of the enhanced MPC controller was compared to PI controllers on both the simulator and a commercial plant. The MPC controller showed faster responses with less interaction in both cases.

Jan 1, 2003

By J. Drzymala

Ores and raw materials are subjected to mineral processing operations to increase the content of their useful components. Upgrading of these materials can proceed with different selectivity and therefore, there is a need to know and monitor the separation results of the process. The separation results can be evaluated using tables and graphs called upgrading curves. The course of lines in the upgrading curves is usually complex and depends on the graph type and process parameters. The Halbich grade vs. recovery plot is frequently used because is practical and it indicates several characteristic features of separation results. Separations by means of flotation of several different shale, dolomite and sandstone copper ores were performed along with determination of their mineral composition, copper content, liberation degree, and the maximum theoretical copper content in the first concentrate. These data, plotted as the Halbich upgrading curves, allowed to find other characteristic points such as practical maximum copper content in the first concentrate, maximum curvature coexisting with the liberation degree, maximum recovery of ore valuable components, and the slope the recovery-grade line at high recoveries as a measure of liberation. Correlations between theoretical and practical maximum copper contents in the first concentrate as well liberation degree and maximum curvature were also presented. They show that the ore type significantly influences the shape of the Halbich curve and its characteristic points.

Sep 1, 2012

By F. Waanders, Campbell. Q.

This project was specifically aimed at using increased acceleration separation, as a method to optimize the recovery of gold in an ore body mainly consisting of hematite where the specific gravity of gold is much higher in comparison to the carrying material, making it possible to separate gold from other materials like silica, base metals and their oxides, usually associated with gravitation-gold-recovery-processes. The ore body investigated in this project originated from a gold reef containing a large portion of gold locked inside the gold pyrite complexes, which was mined and treated in a conventional way. After gold extraction, the material was pumped to a tailings dump and the gold extraction of this dump was investigated. In order to assemble a concentration plant setup, the head grade and size distribution of the dump and bulk sample were determined accurately. Chemical analysis and mineralogical examination were done on a representative sample of the bulk sample, to determine the chemical composition of the material. The results obtained thereof were evaluated and a pilot plant was configured. A bulk sample was processed in the pilot plant and the results were evaluated. The results at optimum acceleration forces applied, resulted in a recovery of 5% of the mass, with a gold concentrate of 90 g/t Au, which represented 58% recovery of the gold. The hematite with high specific gravity as main phase positively influenced the high acceleration separation process. It proved that if the specific gravity of particles in a suspension were increased, high acceleration separation could be applied effectively to separate much smaller particle sizes.

Jan 1, 2014

By E. Lee

Cone crushers are widely used within the mining and aggregate industries for the size reduction of minerals, ores, and rock materials. In mining applications for example, the product from cone crushers is often fed to HPGRs or directly to mills in the subsequent grinding circuit. An improved cone crusher performance can therefore result in an overall improved and more efficient comminution process. The objective of this paper is to systematically study a number of different ways of applying compressive crushing. By mathematically modelling these different crushing concepts and then theoretically optimizing crushing sequences accordingly, each concept can be studied and evaluated. In addition, aspects concerning whether or not the results are mechanically or practically achievable are considered. This study thus explores the advantages and disadvantages of different crushing concepts. In this paper, four different theoretical crushing concepts are presented and studied. The results show that in terms of interparticle crushing, optimal crushing sequences with varying compression ratios can be replaced by easier implemented series of constant compressions without significant deterioration. It is also shown that that considerably better performance is obtained for crushing sequences with both breakage modes. The subsequent comparison between such concepts indicates that different approaches can achieve the same results, and that the different concepts are comparable. It is further concluded that interparticle crushing should be kept to a minimum if fines generation or energy consumption is to be minimized, and that each of the studied concepts presents different challenges for implementation. Keywords: compressive crushing, cone crusher, optimization, modeling, crushing concept

Sep 1, 2012

By M. Alvarez-Silva

The control of the amount of chromite reporting to the concentrate during the flotation of UG2 ore is of critical importance since its presence affects the downstream smelting process. It is generally reported that the main mechanism responsible for chromite recovery is through entrainment. This is reflected in analyzing the solids and water recoveries. These in turn are strongly dependent on the froth phase. In the present investigation a laboratory scale column flotation cell was used to investigate the role of the froth phase in the flotation of UG2 ore. Such a device is superior to a standard batch cell since it operates at steady state in open circuit and also allows for a greater degree of flexibility in terms of froth heights. The mass of solids and water recovered in the concentrate as well as chromite (Cr2O3) recovery by size class was determined as a function of froth height, superficial gas velocity and depressant dosage. The results showed that depressants had little effect on chromite recovery but increased the grade due to the depression of gangue minerals. A 60cm froth height always resulted in slightly lower solids, water and chromite recovery than for 30cm. Typically only 20-25 % of solids reaching the pulp-froth interface reached the launder. The relationship between solids and water recovery for a wide range of conditions indicated that chromite is mostly recovered by entrainment. Keywords: UG2 ore, column flotation cell

Sep 1, 2012

By A. V. Bogdanovich

Until recently, in consideration of fundamentals of gravity concentration theory, all computations have been based on determination of particles? fall velocity in an unrestricted medium (hydraulic size). Meanwhile, gravity separation processes are realized under conditions of particles? restricted fall, when important and sometimes decisive role is played by interacting forces of particles, dependent on their varying size, density and shape, i.e., segregation forces. We have developed devices and methods for measuring segregation velocities of fine particles of various size, density and shape during their loosening in air or aqueous medium. Besides, to exclude influence of medium upward flows, loosening was provided by superposition of vertical harmonic oscillations on measuring cell. It was established, that maximum segregation velocities are observed at certain optimal acceleration values and amplitudes of oscillations; excessive loosening leads to mixing and worsening of segregation. Velocity of some particles segregation through others depends on particles? size, density and shape, as well as nature of medium (air, water). Absolute segregation velocities of particles in air medium may reach 1~2 mm/s, in aqueous medium such velocities are by an order smaller. Analysis of rare-metal sands material gravity concentration results showed, that owing to segregation process during gravity separation, fine-size isometric particles of heavy minerals are recovered into gravity concentrates more actively, than larger ones, but more elongated in shape. It is convenient and simple to estimate mineral grains? shape by extent of their oblongness, described as ratio of particle minimal dimension to maximum. Besides, mineral mixtures gravity separation results are directly related to extent of oblongness of heavy particles, recovered in gravity separation process, and also to root-mean-square coefficient of their shape variation. The performed research showed that particles segregation in gravity concentration process plays not a lesser role, than hydrodynamics parameters, and demands further theoretical inquiry and experimental studies.

Jan 1, 2014

By E. V. Bratygin, S. P. Elnikova

"In the article carrying out technique of experiments for estimation of power efficiency of process of crushing in cone crushers «in a layer». The conformity of the granulometric characteristics of the crushed products obtained as a result of the tests, the theoretical equations for the size characteristics, and the choice of the optimal equation for the prediction of the granulometric characteristics of the final products obtained by crushing ""in a layer"". Optimization of granulometric composition of power of crushers working ""in a layer"" is carried out with the purpose of reduction of the electric power consumption at reception of a product of required quality. As a result of the experiments, dependencies are obtained, the relevance and applicability of the crushing process ""in the layer"" for obtaining crushed stone of improved quality is proved. INTRODUCTION A number of equations have been proposed for calculating the breakage energy. These include equations by Kirpichev and Kick, Rittinger and Bond (Bogdanov, Olevsky, 1982). Another equation for calculating the specific breakage work in breakage by impact and in stratum was proposed by Devyatkin (Boiko, 2003). In these equations, the breakage energy is proportional to the particle size raised to some power. In the equation proposed by Devyatkin, the ore piece thickness or the feed average diameter is used. The relationship between energy and breakage can be expressed as an equation (Lynch, 1981; Tikhonov, no. 3, 2008) where k is a coefficient characterizing the energy parameter depending on the strength of the feed, l is size in microns. The Rittinger formula is obtained for n = 2, the Kirpichev-Kick formula for n = 1, the Bond formula for n = 1.5. For n = 3 or higher, the equation describes fine and ultrafine grinding. R. Hookey proposed a formula (Lynch, 1981, Tikhonov, no. 3, 2008), where the size exponent n is substituted by a size function In all of the above equations, a single value of the feed and product size is used; for example, in the Bond equation, size is defined as the particle size of the 20% oversize (P80 and F80). However, a single size value can represent multiple distributions, making that the Bond method inappropriate for determining the size (Lynch, 1981). Describing an equation for estimating the grinding energy will allow to design the electric drive and ore preparation circuit for the given breakage method."

Jan 1, 2018

By W. P. Roux

With depletion of higher grade iron ore reserves, and the need to process finer, lower grade material; there is a need to better understand the recovery efficiency of jigging process. The use of Positron Emission Particle Tracking (PEPT) was examined as a technique, to study the motion of particles inside a laboratory batch jig. PEPT is a noninvasive method that can provide three dimensional kinetic data of a particle during jigging. Particles with different densities and sizes were traced under the same jigging parameters, to obtain a data set that can be used for the development and verification of jigging models. From the results, detailed information on the stratification rate of a particle was obtained, with adequate resolution to see particle movement through an individual pulse. Detailed data of this nature is critical for the validation of CFD and DEM models. Keywords: positron emission particle tracking, jigging, jig models

Sep 1, 2012

By D. B. Sundar Ramam

In the recent past, a paradigm shift in terms of resource utilization and beneficiation practices is experienced by the Indian mining and mineral sector. Depleting iron ore reserves coupled with increasing demand for low-alumina iron ore fines to improve blast furnace performance in terms of productivity and reduced slag rate necessitate intensive beneficiation of iron ore. The task is even difficult for Indian iron ores, which are generally high in iron content and at the same time characterized by aluminous gangue. In 2006, M/s Tata Steel commissioned a state-of-the-art Jigging Plant (Batac Jig) at Noamundi Iron Mine (NIM), mainly to reduce alumina in iron ore fines. The jigging plant is incorporated in the existing beneficiation circuit to treat ?10+0.5mm size fraction of classifier fines. Over the course of plant stabilization while the plant could deliver desired ore upgradation and average product alumina, variability in terms of alumina content has been a concern. This paper discusses a case study of process parameters optimization in jigging operation to achieve consistent product quality while improving the effectiveness of gravity concentration for the beneficiation of Noamundi iron ore also to take care of inferior plant feed (input) grade year on year. The operating variables used to optimize jigging operations include bed height, pulsion and suction time, particle size, strokes, and plant throughput rate.

Sep 1, 2012

By A. V. Bauman

"Important for thickening processes is the ability of slurries to form under certain conditions aggregation and sedimentation stable systems. Substantial part of difficult to sediment solid particles in such systems may be in colloidal state. The technique to study the sedimentation and aggregative stability of the slurry developed by the author with co-authors makes possible to define kinetics of changes in the aggregative stability of the system with solid phase varying concentration in it and produce data on sedimentation stability of the system in preliminary investigation of the thickening process. Research of aggregative and sedimentation stability of the slurry complement standard methods of laboratory studies to prevent errors in development of water-slime thickening balance and water circulation to design new and upgrade existing processing plants. Statistical analysis of process audits of more than one hundred upgraded and newly commissioned processing plants carried out in recent fifteen years showed that more than two-thirds of problems arising in commissioning the processing plants are associated with misdesign and errors in thickening and water circulation system. Among the main reasons of process design failures are: non-conformity of actual characteristics of the raw material to design characteristics, low quality of preliminary studies at the stage of sedimentation process simulation, design failures, wrongly selected equipment for the thickening and water circulations systems. As of today a number of problems associated with laboratory studies of sedimentation process, first of all, with interpretation of precipitation curves produced at the stage of laboratory refinement of the thickening process have been pinpointed. (Bauman A.V. Outstanding issues in design of thickening and water circulation diagrams in processing plants // Ore processing. 2016. ?3 P. 58-62) ?????? ?.?. ?????????? ??????? ?????????????? ???? ???????? ? ??????????? ?????????????? ??????. // ?????????? ???. 2016. ?3. ?. 58-62))"

Jan 1, 2018

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels.This paper analyses the reasons for the inadequate level of pro-active plant maintenance practice in industry today, and presents a number of important criteria in selecting appropriate solutions to this problem. A case study of a specific real-time, remote equipment management application is presented."

Jan 1, 2003

By Leon Lorenzen, Nursen Guresin, Harald Muller

The development of mining projects from discovery, exploration to actual production is a complex and time consuming process. Often poor process plant performance can be attributed to the use of non-representative samples and inadequate and/or unsuitable metallurgical test work when designing flow sheets during project feasibility study stages and specifying process equipment. Samples not representing the ore deposit and inadequate test work may lead to increased project development costs, since expensive test work and engineering may have to be repeated. It should be noted that for higher level engineering studies, larger scale test work is recommended and is a requirement for feasibility level studies. This would apply even if the technology is considered mature and well proven, as each ore body may have its own unique characteristics that, if untested at a larger scale, could result in significant design shortcomings, which will have to be rectified at later stages of the project, usually at significant additional costs

Jan 1, 2014

By Masoud Askari, Ahmad Rafizadeh, Shahamat Rostami, Mohammad Qaredaqi

Gole - Gohar Iron ore mines located in Sirjan, Southeast of Iran, have more than 1 billion Iron ore deposit and this area comprises 45 % of Iran Iron reservoirs. The aim of Wet tailing processing line is recovering Hematite ore from wet tailing of Gole - Gohar iron ore processing plant. The Investigations of Hematite recovery plant showed that the recovery of Iron ore to concentrate in Wet Tailing Processing (WTP) line is very lower than that has been predicted, sampling, and designing of the process parameters are not accurate and designed magnetic field intensity is not reasonable for the recovery of Iron in form of Hematite in this line feed. Applying of MIMS in WTP separator and changes in circuit caused in overwhelming increase of Fe recovery, from 11 to 40%. Although recovery of WTP line was improved, but low recovery of this processing line and high content of Hematite ore in WTP tailing, made applying Wet High Intensity Magnetic separators unavoidable. Two kinds of WHIMS have tested for processing of WTP line tailing. Results showed that traditional Jones separator with grooved plate matrix, is more suitable to achieve a better quality of concentrate compared to Slon® separator.

Jan 1, 2014

By Shuji Owada, Mayumi Ito, Idemitsu Kosan Co. Ltd., Takehiko Nishimu, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

"fElectrical disintegration (ED) by high voltage electrical pulse is a relatively new technique which was demonstrated by Tomsk and Mekhanobr in the 1960’s and has been investigated in detail by Andres in the 1990’s. In the ED, the electrodes should contact to the targeted material and the energy of high voltage pulse is charged directly to the material. It has been reported that the ED is quite efficient to improve liberation of composite materials, because electrical current passes often through the conductive part and/or along the phase boundaries. Theoretically, the energy required in the ED should be lower than in the other mechanical breakage methods, because breakage occurs basically by tensile strength in the ED while in the other mechanical methods it does mainly by compressive strength which is generally ten times or higher than tensile strength.Coal, involving many kinds of mineral matters, is considered to be one of the targets for the ED to apply to. In Japan, national “Hyper-Coal Project” is now running, in which ultra-clean coal (less than 200ppm of ash, 0.5ppm of Na and K, and 2ppm of Ca) is planned to produce by combining advanced coal preparation and liquefaction technologies for the purpose of direct injection of coal combustion gas to turbine. The ED is one of the major techniques to be developed in this project, since mineral matters must be liberated before introducing to the following advanced separation processes. Liberation is important also for the utilization of middling coals generated from usual coal preparation plants. The application of the ED to the middling coals is considered effective for upgrading these coals with higher liberation degree and less energy input."

Jan 1, 2003

By H. Hamza, M. R. MacIver, M. Pawlik, L. Malin

"Size and shape are important properties of aggregates formed in engineering processes and natural systems. Measurement of aggregate size or shape is a challenge when the solids concentration is beyond the gel point, ?? > ??g, when the aggregates are in contact and it is difficult to distinguish or segment individual particles in the network. This paper describes the use of a micro-computed tomography (micro-CT) method for the calculation of the aggregate volume fraction, ??, and a characteristic aggregate length, ??a, based on a 3D chord length measurement algorithm. These parameters can be used to quantify changes in aggregate and pore size during a compressive yield stress test to help understand the impact of flocculation and network structure on dewatering. INTRODUCTION In a thickener, flocculation is often used as a pre-treatment step and the final solids content of the underflow depends on the network strength and permeability of the bed formed by settled aggregates (Usher, Spehar, and Scales 2009). This paper describes the measurement and analysis of micro-computed tomography (micro-CT) of flocculated mineral sediments to obtain a characteristic length, ??a, of the aggregate and pore phases during a staged compressive yield stress experiment. This parameter may be used as an indicator of changes in aggregate and pore size to quantify material behaviour in solid-liquid separation processes that depend on self-weight compression or applied pressure. This analysis was carried out to help understand the effect of flocculation on aggregate structure and the thickening process as part of a broader research on the improved solid liquid separation of tailings produced in the oil sands industry.Aggregate properties The solids phase of an aggregated or flocculated suspension will eventually settle – if left undisturbed – under the influence of gravity. As settling of a flocculated suspension continues, the solids volume concentration, ??, may increase to the gel point or gelation threshold (Landman and White 1994), ??g, above which the aggregates form a network of touching particles, or space-filling structure (Kranenburg 1994). In the sediment bed, the aggregates are surrounded by fluid and occupy a partial volume fraction, ??, according to"

Jan 1, 2018

By Shuji Owada, Mayumi Ito, Takehiko Nishimura, Toru Yamashita, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

Electrical disintegration (ED) was applied to Nantun coal (China) in order to improve liberation of coal substance for the pretreatment of producing “Hyper Coal” of which the combustion gas was planning to inject directly to turbine for power generation. It has been found that many cracks generated in the ED were existent at phase boundaries with mineral matters and liberation of coal substance became much higher than that in mechanical comminution methods such as roll crusher. Since the ED occurred more easily (with lower voltage applied) for the coals of higher mineral content, it is considered that this method could make a better contribution especially to comminute middling coals. We also found that the ED technique could apply not only single particles but also to coal particles assemblage, keeping almost the same or higher disintegration efficiency. In the mineral matters, Si and Al components were preferentially well liberated by the ED.

Jan 1, 2003

By Yuri L. Nikolaev

The treatment of placer gold with fine gold, associated with gold-bearing sulfide minerals, heavy minerals and oxidized minerals such as manganowolframite (gubnerite) is not an easy task. In this case, this complex material cannot be treated using physical separation methods such as deep concentration and finishing, magnetic separation and solvent extraction. This technology is usually employed in gold washings finishing plant. The easiest way to recover precious metals in the form of an easy-to-sample saleable product is metallurgical treatment. This paper describes the application of pyrometallurgical processes with oxidative roasting, re-cleaning of cinders (if required) and ore-thermal smelting for producing gold bullion. Hydrometallurgical treatment of slags as an additional operation is recommended in order to maximize recovery of valuable metals. After this treatment, a barren leaching cake rich in PGM can be sold in the market. PGM can be collected as gold-silver alloy during smelting which allows the phase formation of polymetallic matte due to specific composition of fluxes. The PGM are then in the form of saleable gold bullions in the refinery.

Sep 1, 2012

By S. Martins

The aim of this work is to compare three different results of charge motion in a modified 5ft diameter lab mill and to identify differences and similarities in these results. The lab mill is modified from tumbling a ball charge to tumbling a charge of disks. This modification replicates 2D motion. This 2D condition is measured using an instrumented disk (iDisk) and analysed using a video imaging system. The iDisk is equipped with a 3D accelerometer array and rotation rate sensors. With the help of a video system, some measured quantities are also determined externally. The results of these three predictions or measurements are presented. A discussion is included.

Jan 1, 2014