Search Documents

By I. Zh. Bunin, G. K. Khachatryan, N. E. Anashkina

For optimization of diamond processing technology the influence of nanosecond high voltage pulses on mechanical and technological properties of diamond crystals and kimberlite rock-forming minerals (calcite, olivine, serpentine) was investigated. Using methods of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), microscopy and mikrohardness measurement the changes of structural, physic-chemical surface properties, and microhardness of minerals as the result of impacts, was studied. Non-thermal impacts caused a decrease of kimberlite rock-forming minerals microhardness in general to 40-66% as the result of surface microstructure destruction which is caused by formation of micro cracks, traces of surface breakdown and other defects. At the same time, the pulse energy impact on natural diamonds led to formation of B2 type crystal lattice microsift defects, elevated concentration of which increases the hardness properties of crystals. The obtained result indicates possibility of applying pulsed energy effects to improve the softening efficiency of diamond-bearing kimberlites rock-forming minerals without damaging the diamond crystals and ensuring their preservation by the subsequent grinding of ores. By IR and X-ray photoelectron spectroscopy revealed that processing by hight voltage pulses causes a change of natural and synthetic diamonds surface functional cover composition. Short-term exposure (~ 10 - 30) leads to detachment and partial destruction of secondary phases mineral films on the surface of natural technical diamonds, increasing floatability and hydrophobicity of crystals. However, with increasing duration of treatment (~ 30 - 150) occurs surface hydroxylation (found by XPS for synthetic diamonds), as a result of diamond surface layer oxidation. The effect of increasing the natural diamonds flotation activity by 14% (from 47% to 61%) was experimentally established as a result of processing diamond crystals with nanosecond pulses (~ 10-50 sec), which indicates the principal possibility of using pulsed energy impacts to intensify the diamond flotation during processing diamond-bearing kimberlites.

Jan 1, 2018

By Mike Daniel, Eric Wang

"Several new large copper and gold concentrators have been built and commissioned around the world in the past five to eight years. The success of the ramp-up from these very large concentrators has varied. CITIC SMCC Process Technology was engaged to assist some of these mines by gaining a better understanding of the factors that influence throughput capacity. As such, site-specific throughput forecast models that are influenced by SAG mill performance were developed. The forecast models are easy to interpret and modify and can greatly assist the mine management to make predictions and informed decisions for a range of site improvements. The models investigate the influence of SAG mill performance with respect to ore competency, derived from SMC Test® via the measured DWi model parameter. In some cases the benefits of blasting and from fine tuning milling operations are already incorporated into the "site-specific" forecast models. The methodology follows rigorous plant data analysis that is analogous to a "Mine-to-Mill®" optimisation project. The CITIC-SMCC model validation includes extensive data collection, which includes drill core analysis, ore characterisation and comprehensive comminution circuit operational data to assess the limitations within the comminution circuit within the operating mine. The results and models may be used to define the operating base lines of the processing areas and identify improvement opportunities upstream and downstream of the comminution circuit. The predictive capability of the models use logged production data and has enabled the user to differentiate between alternative circuit configuration options and identify optimum operating conditions. This approach minimises the ongoing requirement for costly plant surveys. The improvement strategy for each site, included the ongoing measurement of grindability, rock strength and via the Bond and SMC Test® respectively. Some commentary as to what other practitioners do with input data and their models is also presented as this highlights some of their shortcomings relative to the CITIC-SMCC methods."

Jan 1, 2014

By Vladimir G. Kochnev

"Autogenous and semi-autogenous grinding (AG and SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills. However, existing AG and SAG technologies still can be improved and have an immense potential from the viewpoint of economic benefits.Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that comminution in AG and SAG mills can be performed in a more effective way. The company’s approach comprises the following elements:- Novel mill design- New liners and lifters- Novel discharge grid design- Technique of treating material of critical particle sizeA novel mill of the cantilever type capable to operate in the AG and SAG mode has been developed. The cantilevertype mill has a high diameter to length ratio, which dramatically increases the throughput rate, and is characterised by high reliability, fast installation and low capital and operating costs.Tests of the new heel-shaped liners, originally aimed at improving the intact condition of diamond, indicated that they play an important role in the grinding process. Tests performed by TTD jointly with ALROSA, MINTEK and Anglo-American Corporation, demonstrated that the heelshaped liners provided the increase in the throughput rate varying from 30 to 80 % and the decrease in power consumption in the range 30-55 % for grinding of kimberlite and platinum-containing ores.Investigation of the influence of the main grid parameters on the efficiency of grinding led TTD to a special design of a mill discharge grid, with a radial location of openings, the slot width varying from the periphery to the centre and the grid surface provided with “heels”. The design allows one to control the particle size distribution of the ground product without affecting the grid throughput rate."

Jan 1, 2003

By Peter Ay, Harry Pempel, Satya Narra, Mike Müller, Jens Markowski

"Within the next few years major changes in mobility are expected. Increasing numbers of electric powered cars, electrobikes and E-Scooters define the transport sector. Recently lithium based traction batteries as storage medium have led into matrurity of series production combining high electrical efficiencies with low weights and compact dimensions. Due to the relatively young development with lithium batteries utilization, only few investigation were conducted regarding their recycling. Conventional battery recycling processes can not be applied due to differences in design and chemistry. So an automated disassembly and processing procedure for lithium traction batteries has been developed in the R/D-project ""Li-WERT"". Instead of complete smelting of the batteries without pretreatment, an automated disassembly and specific treatment of the material streams was realised, adjusted to the needs of the subsequent recovery technologies. A higher quality, with reduced expenses for the separation of fine-grained or fused material mixes, can be obtained for the individual components. The automated disassembly using an industrial robot significantly reduces dangers for the operating crew. The selective disassembly and beneficiation allows full recovery of the fractions. The batteries will be disassembled to cell level by the industrial robot. Anodes, cathodes, and separation layers are isolated and processed. The technology is designed, that no waste is generated for disposal. The pelletised cathode coating and the other separated metals (stainless steel, copper, aluminum) can be used in respective metallurgical plants. Circuit boards and plug contacts are also coveted secondary raw materials for reuse. The process is modular and offers high flexibility, e. g. for new battery types/ sizes by quick adjustment of the robot and tool change. Adaptation to other cathode materials (e. g. Li[FePO]) is possible. After finishing the R/D-project, a pilot plant for demontage was realised in 2013."

Jan 1, 2014

By M. Morales, J. Yianatos

"In this work, an alternative approach to evaluate the flotation performance along a flotation rougher row is presented. The collection zone as well as the froth zone performances were separately evaluated. For this purpose, sampling for metallurgical balances along with sampling of top-of-froth (TOF) grades in each cell of a flotation row were employed. The modelling of the rougher circuit consisted of using TOF grades for evaluating the collection zone recovery, because they are a good representation of the bubble loading, which identifies the true flotation process, as shown in previous studies for shallow froths. In addition, the feed characterization, size-by-liberation, allowed the identification of the mineral distribution and its evolution along the circuit. The latter result was obtained by fitting the recovery profiles as well as the TOF grades down the flotation bank. The flotation rates and the maximum recoveries in terms of size-by-liberation (size classes: -45 µm, +45-150 µm, +150 µm, and liberation classes: -20%, +20%-80%, +80%) were then estimated. The results were in good agreement with those reported in literature by other authors and showed the new approach allows flotation kinetics to be characterized in industrial circuits.INTRODUCTIONMineral recovery in industrial flotation circuits is a function of the mineral characteristics, such as particle size distribution and liberation (Trahar, 1981, Jameson, 2012), and operating conditions such as air flowrate, pulp flowrate, solids percent and reagent conditioning (Jameson 1977; Klimpel, 1980; Mehrotra and Kapur, 1974). The cell type and size (self-aerated or forced air) and the circuit arrangement (single cells or banks of cells in series) are also relevant factors. Sampling of circuits (e.g. rougher, cleaner or scavenger) are commonly carried out using standard automatic samplers for metallurgical balance assessment. However, the flotation plants are generally not provided with proper accesses for local streams, which hinders the recovery estimations and the flotation rate characterization."

Jan 1, 2018

By Chris J. Martin, Nichola A. McKay

"In mid-2001, North American Palladium commissioned a new 15,000 tonnes per day milling and flotation circuit at their Lac des Iles Mine (LDI), one of only two primary platinum group element (PGE) producers in North America. The mill treats an ore containing 2.3 g/t PGE producing a concentrate assaying 300 g/t PGE, at a recovery of roughly 75%.Top-size control crushing is conducted ahead of semi-autogenous milling. A portion of the SABC circuit feed is crushed to –25mm to increase mill throughput. Product from the SABC circuit is fed to flotation. Flotation consists of roughing and scavenging, with the rougher and scavenger concentrates each being reground using vertimills. Cleaner flotation uses two stages of cleaning using mechanical cells, and a third stage using flotation columns, the column tails being scavenged using a bank of mechanical cells. Rougher concentrate by-passes the first cleaner circuit. Reagents added include amyl xanthate collector, dithiophosphate promoter, MIBC frother and a carboxy methyl cellulose-based gangue depressant.SGS Lakefield Research, together with staff at LDI initiated a structured plant optimisation program comprising on-site testing, bench-scale flotation and mineralogical analysis using QemSCAN. The objectives of the mineralogical studies were 1) to identify feed PGM, their size distribution and mineral associations, 2) establish relationships between the PGM mineralogy and PGM floatability, and 3) characterize the culprit silicate minerals diluting the final concentrate.PGM flotation response at Lac des Iles is clearly bi-modal in nature, with about 60% of the PGM floating quickly, to a high value rougher concentrate. The mineralogical work was able to explain the causes of the bi-modal PGM floatability, which in turn created new opportunities for the metallurgists to optimise the circuit."

Jan 1, 2003

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

By I. Blayda

The purpose of this work is to study and make comparative analysis of germanium extraction and related valuable components of the sublimates from the burning of domestic power coals (product 1) and germanium sulfide materials, which are a waste of lead-zinc production (product 2), by traditional chemical methods (distillation of germanium in the form of tetrachloride from raw and preliminary burning source) and by microbial bioleaching of sulfur-oxidizing bacteria. The dependence of the germanium extraction by chemical methods from phase composition of the initial raw materials was installed. The germanium tetrachloride extraction from products 1 and 2 were 78.50 and 19.52%, respectively. Such difference in indexes on extraction, is caused by germanium confinement as concomitant trace component to the basic phases to carriers. The share of acid-non-soluble compounds (tetragonal modification GeO2 and silikogermanaties) in the product 1 account for 21.5 % of germanium. Ratio between acid-soluble and acid-not -soluble germanium forms are 19.52 and 80.48 %, respectively, in the product 2. Our experiments have shown, that implementation of restorative firing (with addition of 30-40 % carbon at 1150 0?) of sulfide product 2 considerably impacted on the extraction of germanium tetrachloride (91.76 %) in comparison with its low enough extraction at straight distillation of hydrochloric acid (19.52 %). The results are confirmed by a set of physical methods. The results of processing the same so-called hard phase?s material (product 2) with the help of microorganisms are presented. It Has been established, that selected strains of bacteria are capable of extracting from initial raw materials not only macro components (iron, zinc, lead, manganese, aluminum, nickel), but also micro impurity of rare metals (gallium, germanium, zirconium). It is important that these metals were not extracted by traditional chemical methods (with application of aggressive conditions and heats) independently of the phase composition of the source. Almost complete extractions of germanium in solution using sulfur-oxidizing bacteria take place in the first day of the process independently of the phase composition of the source and the type strain. The results have practical significance and can be the basis for developing a unified biotechnological method of technogenic waste processing with a purpose of their sterilization and detoxification with simultaneous obtaining concentrates of valuable metals. Keywords: germanium, extraction, sublimates, bioleaching, sulfur-oxidizing bacteria.

Sep 1, 2012

By D. Kosior

Influence of frothers (a-terpineol and n-octanol) concentration on kinetics of a three phase contact (TPC) formation by a bubble colliding with a hydrophobic surface (Teflon) of different roughness was studied using a high-speed camera (1040 frames per second). It was found that the Teflon surface roughness and the frother concentration strongly affected time of the TPC formation (tTPC) and time of drainage (tD) of the liquid film separating the colliding bubble from the solid surfaces. With increasing Teflon surface roughness, from ca 1 to 80 µm, the time of the TPC formation was shortened by over the order of magnitude, from ca 100 to a few milliseconds only. At low a-terpineol and n-octanol concentrations, thetTPC values were shorter than in distilled water due to lowering the bubble velocity in the frother presence and diminished bouncing of the colliding bubble. However, at high frothers concentrations the tTPC values were prolonged, despite that the bubble velocity was similar. The prolongation of the tTPC at high frother concentrations indicates that air (micro- and/or nano-bubbles) was present at the Teflon surfaces of different roughness. The mechanism of the tTPCprolongation at high frother dosage is described.

Sep 1, 2012

By N. D. Dementieva

Based on lab and pilot-plant tests to recover gold, silver and lead of a Russian deposit, a collective and flotation concentration flow sheet with lead and sulfide concentrates was proposed. The type of the deposit is gold-sulfide-quartz-bearing. The recovery of gold, silver, and lead to a lead concentrate was 47.4%, 68.1% and 70.7%, respectively. The grade of gold and silver grade was 170 g/t and 372 g/t, respectively. The mass percent of lead, zinc and arsenic mass percent was 41.7%, 0.34% and 0.63%, respectively. The recovery of gold and silver recovery to a sulfide concentrate was 50.1% and 28.8% at the grade of gold 20.5 g/t and silver 66.2 g/t. Sulfide concentrate with arsenic mass percent ~3% was biooxidised followed by CIL and obtaining metal at the site as well as zinc concentrate from bioleaching solutions with zinc mass percent 45% at its 64% recovery. The total gold and silver recovery using a developed technology with the account of their treatment at a polymetallic plant was 92.2% and 93.7%, respectively.

Sep 1, 2012

By D. Chakraborty, Neeraj Kumar

"The study provides the comparative analysis of the performance of water only cyclones and hydrocyclone for iron ore fines processing at Joda Iron ore processing plant, Tata Steel. Joda iron ore deposits have higher proportion of kaolinite in the finer fractions and are meant to be separated with cyclones. The iron processing flowsheet of Joda comprises of water only cyclone for beneficiation of iron ore fines. Water only cyclones are used for the beneficiation of fines in the iron ore processing industry and have a larger cone angle compared to that of conventional hydrocyclones to enhance the density effect in the separation. They are aimed to achieve better product quality of underflow however; the desired result could not be achieved at the Joda processing plant. The water only cyclones were operating at the corrected cut-size of about 60 micron with an imperfection of 0.40 and water split to underflow was approximately 10%. The overall Fe recovery from the water only cyclones were 60%. Since the quality of fines produced from the water only cyclone couldn’t be improved, an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality. The trial results indicated better product quality with the Fe recovery of 72% at corrected cut-size of 70 microns and imperfection of around 0.29. In view of above results it was recommended to replace the water only cyclones with hydrocyclones to achieve higher product quality of about 60% Fe content.INTRODUCTION Water only cyclones were installed at wet plant, Joda to process the classifier fines where the cyclone underflow is considered as concentrate and overflow is discarded as slime. Because of the lower capacity of the cyclones 30% of the classifier overflow was bypassed directly to thickener. Apart from this the quality of fines produced from the water only cyclone couldn’t be improved further hence an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality and quantity. Hydrocyclone was installed at Joda after replacing stub-cyclone and came into operation on 23rd Aug’ 2017.The process variables of water only cyclones and hydrocyclones are tabulated below:"

Jan 1, 2018

By M. Ito

The authors have developed the RETAC jig (a modified TACUB jig) and have reported that the RETAC jig can separate relatively low density particles such as plastics. To further improve the separation ability, a hybrid jig (a RETAC jig with an air bubbler under the particle bed), which can separate plastics having similar specific gravities by the differences in the wettabilities of the particles was developed. Surface modification of plastics with similar wettability enabling separation in the hybrid jig and the effects of wettability control of the plastics using reagents are reported.

Sep 1, 2012

By H. Araneda

Throughout Chile?s history, mining has consistently been a leading industry in the country. The 1990s marked the beginning of a boom in Chile?s mining industry, especially in copper mining, due to both foreign and local direct investment in the sector. Mining?s contribution to the GDP was 15.6% at current prices in 2009, and it accounts for 56% of the country?s exports. Chile?s copper market share reached 35% in 2009. The investment portfolio in mining in Chile for the coming decade has been estimated at 90 billion US dollars. The acute scarcity of human resources currently experienced by the mining sector in Chile will be accentuated in the coming decade as a result of this scenario of investments. The situation is, additionally, similar to the one confronted by other countries involved in the mining industry such as Australia, South Africa, Canada, and in Latin America includes, Peru, Colombia and Brazil. A study carried out by Fundacion Chile, ¨Labor Force in the Chile Mining Industry, Diagnostic and Recommendations, 2011-2020? shows the projected labor shortage for the operation of projects in the development stage, considering only the requirements of the process of extraction, processing, and maintenance. The demand, accumulated incrementally, will be around 115,000 technically skilled workers, professionals, and qualified workers. This figure refers to the operational work force, and does not include the human resources that will be required for the prior stage of the engineering and construction of the projects (brownfield and greenfield). The demand for technically skilled workers and professions for the stages of engineering and construction of the projects that have already received investments is estimated to be 190,000 people for the period 2012-2020. The peak of the demand for engineering is 2012, with a figure that surpasses the 12,000 professionals for all of the engineering specialties. The analysis of the formation of human resources at the tertiary level (where tertiary includes technical/vocational and academic degrees at the undergraduate level) for mining and related majors demonstrates that the programs are scarce with a bias toward theoretical contents and that they are excessively long (40% longer than comparable programs in Australia, Canada, and in OECD countries). The completion rates are low, especially in the technical-vocational programs, which have a completion rate of only around 30%. Finally, the rates of attraction of technically skilled labor and professionals towards careers in mining are insufficient to reduce the identified skill gaps. In the case of university professionals such as geologists, mining engineers and engineers in metallurgy, 80-90% will work in mining. In the case of graduates of relevant majors, that cover skills also utilized by other industries, not only mining?such as maintenance workers, operators of fixed and mobile equipment, etc.?the mining sector appears to be unattractive for reasons such as shift schedules, geographical location of work sites, and other factors. On the basis of the available diagnosis a strategy for the sector has been developed (Workforce Development and Skills Strategy) whose objective is (i) to define a Mining Qualifications Framework to identify the critical roles to be filled (ii) to start, with public resources, a ¨fast-track? training program to assure the availability of at least 28,000 operators (machinery operators, truck drivers, etc.) and maintenance specialists in 2015 (iii) to promote the development of training hubs for mining with learning technologies to train technical labor and professionals on the basis of world class standards (iv) to design and implement a campaign oriented toward the perception of mining as an attractive field of employment opportunity (v) to develop curricular innovations for tertiary education programs, on the basis of international benchmarks. Keynotes: Chile, mining, copper mining, skilled human resources

Sep 1, 2012

By A. N. Zagorodnyaya, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva, A. S. Sharipova

"In Kazakhstan, there is a unique sulphide copper deposit, in the ores containing the natural isotope of osmium-187 (more than 90 %). In the pyrometallurgical processing of concentrates for the target metal, osmium is mainly sublimated, with wet cleaning of metallurgical gases (dust and gas mixture) 40 % of it together with rhenium passes into washing solutions (wash acid). On the basis of this acid, the production of ammonium perrhenate was organized at the enterprise of the RSE ""Zhezkazganredmet"" and for the first time in the world practice - the isotope of osmium-187. However, the degree of its recovery from solutions does not exceed 8 % of the amount supplied with the charge or 25 % of the amount that was received for extraction. But the bulk of it (~ 75 %) remains in the raffinate, discharged to sewage treatment plants (wastewater). The studies presented in this work are aimed at solving the problem of osmium isotope-187 extracting from wastewater, which are a potential source of increasing metal production in Kazakhstan. The aim of this work is the development and scientific justification of osmium deposition regimes from wastewater using such reagents as thiosulfate and sodium sulphide. The influence of various physicochemical factors on the precipitation of the osmium was studied and optimal conditions for its maximum transition to sediment were chosen. An original method for obtaining osmium concentrate in the presence of sodium thiosulfate with the addition of potassium iodide from a new type of wastewater - man-made ammonia solutions has been developed. These solutions were combined mother liquors of solid-phase stripping operations and dissolution of pulp of crude ammonium perrhenate. On the basis of the obtained results, a settling technology for extraction of the osmium from man-made ammonia rhenium-containing solutions was introduced at RSE ""Zhezkazganredmet"". It should be noted that the degree of extraction of osmium, depending on its concentration in solutions entering on the settlement, and taking into account the addition of sulfuric acid, will vary from 60 to 90 %. The recovery of osmium during the test period was 58 %."

Jan 1, 2018

By M. Naymanbayev

The characteristics of the mineral composition of ores and valuable set of components: the technology of processing depending on the type of mineralization, the nature of the impregnation of ore minerals and their composition have been considered. There have been given technological schemes for processing concrete objects. The analysis of fitness fields for industrial development (degree of scrutiny, the effectiveness of developed enrichment and hydrometallurgy technology) has been provided.

Sep 1, 2012

By Jiang Wenli, Zhang Yimin

In order to enhance the quality of iron concentrate from magnetic separation, reverse-flotation technology is often applied in an iron ore dressing plant.However, this technology has disadvantages in terms of operating cost,energy consumptionand environmental protection(Zhao, Wu& Wang,2005).Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate.This paper describes the development of Complex Flashing-Field Magnetic Cleaner,a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field(Hao & Jiang, 2002).This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magneticfieldwhich can strengthen the formation of magnetic agglomerations and the dispersion of gangue mineralsto improvethe quality of separation.The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process.

Jan 1, 2014

By A. D. Shuloyakov, G. A. Finkelstein, V. I. Kurets, A. K. Vedin

"In disintegrating solid ores with mineral values disseminated in them, one of the principal tasks is to selectively separate valuable mineral particles from the matrix in which they reside, striving at the same time to keep their natural shape and size as intact as possible.The conventional mechanical disintegration methods do not meet this most important requirement in full. The other major objective here is to reduce electric power consumption during the fragmentation stage, since up to 65 per cent of the total power consumption at concentrators processing ores of non-ferrous, ferrous, rare, and precious metals is spent on disintegration steps.Numerous experiments conducted on dozens of ore types (tin, tungsten, and many others, as well as on rock containing diamonds, rubies, emeralds, etc.) have invariably demonstrated by far superior integrity of mineral values as compared with that obtained by mechanical as well as other types of disintegration.However, the process remains as power-intensive as ever which is due to the imperfect nature of the electro-technical devices that convert the network electric current into high-voltage electric impulses responsible for the disintegration process.The maximum capacity attained in disintegrating the hardest materials from 40 mm to 2 mm size in a single operating chamber with four high-voltage electrodes does not exceed 1.0-1.5 t/h. Attempts at increasing the number of electrodes and the capacity of the operating chamber have failed so far because of high overall dimensions and mass of the electrical part of the installation supplying the chamber with pulsating current, as well as of the commutation requirements. At the same time, a number of overseas operations have reported a significant breakthrough in their attempts to reduce dozens of times the overall dimensions and mass of the discharge impulse generating installation (EIS), which enables us to contemplate to increase the capacity of the EIS at least ten times in the nearest future. Yet, even with the currently achieved capacity of the EIS, these installations have found wide use in geological surveying, precious and semi-precious stones production, in grinding super hard materials, etc., since they provide spectacular selectivity of disintegration and thus the integrity of valuable mineral crystals."

Jan 1, 2003

By Jens Markowski

The EU Directive 2000/53/EC on end-of life vehicles (ELVs) states that in 2015 at least 85 wt.-% of a vehicle has to be reused or recycled. This result in the obligatory need to separate additionally metallic and other components of the automotive shredder residues (ASR), so that they can be professionally prepared for recycling and reuse further. Currently the iron-containing fines of ASR are deposited as it is not possible to process in blast furnaces due to its particle size (< 4 mm), composition and material properties. Additionally problems are also caused in handling and transportation (dust) of the material. This work focuses mainly on the ASR materials utilization in blast furnaces. Material was further separated into two consecutive fractions by carrying out repeated crushing and magnetic separation twice. The two fractions have significantly higher iron content (up to 75 wt.-%) compared to the initial material mixture. The materials were assessed for their usage in blast furnaces based on the possible pelletisation with and without binders, stability of pellets, shape and size of pellets, etc. Pelletisation of the material was carried out with a single mould pellet press. Further lignite coal was added to the mixture as additive which improved the pelletisation behavior and the mechanical stability of pellets. Lignite coal was chosen as a reducing agent in the blast furnace process contributing towards additional savings in energy supplied. The experiments reveal that the production of pellets from iron-containing fines is possible with a lignite coal admixture of about 15 wt.-%. These pellets displayed good mechanical stability and can be used in blast furnace processes in recovery of the recyclable metals which are currently not recycled. The recycling of not yet recyclable metals would reduce the deposition and can be easily adopted into the economic cycle by their utilization. Keywords: Automotive shredder residue (ASR), FE-fines, pelletisation

Sep 1, 2012

By T. Mütze

The progress in comminution is often described by the specific surface area and the energy utilization or the brakeage ratio and breakage function. The principal mechanisms of size reduction are therefore, well known. All four parameters share a common disadvantage: They are limited in describing the behavior of a feed material with fine particles and a wide particle size distribution. An alternative is to describe the progress in comminution with ? The particle size distributions Q(x) before and after the stress or ? The particle concentration ratio pcr(x), which combines these two states. In the case of a self-similar fracture behavior, (in short: self-similarity) the progress in comminution can be simplistically described by the relationship between a reference particle size and the stress intensity. Self-similarity means self-similar breakage functions of geometrically similar particles of the same strength, a certain stress situation and stresses up to the breakage point. Self-similar breakage functions show the same curve at different stress intensities when the fragment size x is normalized with a reference particle size xNorm. This behavior was demonstrated for single particle comminution repeatedly and unequivocally. In the field of particle bed comminution, these results differ in literature. Therefore, the self-similarity in particle bed comminution was systematically investigated at the Institute of Mechanical Process Engineering and Mineral Processing of the TU Bergakademie Freiberg as part of a research project. Limestone, quartz, silicon carbide and glass beads, were examined with a hydraulic press. The particle sizes covered monodisperse fractions in the range of 1-1000 µm, bimodal mixtures of these fractions and polydisperse fractions. The results obviously show that there is no self-similar fracture behavior in the case of glass beads, quartz and silicon carbide. Statements on the self-similarity of limestone are much more difficult: Only some of the investigated limestone fractions show a similar clear, non-self-similar behavior. Self-similar curves appear particularly for fine monodisperse fractions as well as bimodal mixtures, which stressed with pressures above 200 MPa. Considering the measurement accuracy of particle size analysis the coincidence of the curves can be explained by the fact that progress in comminution almost ends above 200 MPa. At this point, a hydrostatic stress state is reached in the particle bed which is known from the literature. This stress state inhibits further fractures. Overall, it has been verified for the investigated materials that there?s no self-similar fracture behavior in particle bed comminution. One reason for the diverse opinions in literature is that there are three types of particles after the comminution in the particle bed: ? Particles which are stressed below their breaking point, ? Particles which are stressed right up to the break point, and ? Particles which are stressed beyond their breaking point.

Sep 1, 2012

By Crasta Jeason, T. Sreenivas, M. Narasimha

The subtle nature of the flow inside the hydrocyclone has encouraged development of mathematical models for predicting its performance, which are widely used in simulation of comminution circuits. But most of the models available are based on single average feed density. But the feed to hydrocyclone classifier is generally mixture of particles of different densities. This effect of varying density of feed particles on performance of hydrocyclone has been reported in literature. Further investigation of the effect of multi component feed on the performance of hydrocyclone is the objective of this work. This work involves experimental work to study multicomponent behaviour in various size cyclones. The performance of hydrocyclone for feed mixture of magnetite and quartz has been studied. The effect of presence of magnetite, a high density material on efficiency of separation of quartz has been analysed. It was observed that the effect of component interaction increases with feed solids concentration leading to an increased cut-size for a given optimum cyclone conditions. Based on the multi-component exiperiments available in literature, a concept for modeling the performance of hydrocyclones is proposed. A set of semi-empirical model equations for cut-size, sharpness of separation are presented. An attempt to validate the new hydrocyclone model on multi-component behaviour is made.

Jan 1, 2014