Search Documents

By Tobias Hansson

The quality of Lime Cement (L/C) columns is to a great extent dependent on the installation procedure. At a site in the south of Sweden, the client reported problems with the installed columns. To evaluate the operator and equipment dependent part of the installation, Hercules Grundläggning AB was appointed as a competitor to the site contractor. The purpose was to install a number of L/C columns with equal installation parameters for both contractors. A total of 65 test columns were installed in June 1999. The geology is a typical Swedish organic soil profile with a top layer of peat overlying gyttja and clay. Two different binders were used in the comparison; blast furnace slag with cement and lime with cement. After installation, the quality of the columns was monitored by penetration tests and a column sampler for extracting whole columns. The column penetration test were performed 28 and 134 days after installation and extraction 134 days after installation. Inspection and tests of the extracted columns showed that by using a fully computer controlled procedure, the contractor produces columns of superior quality and homogeneity.

Jan 1, 2000

By O&apos, M. W. Neill

Mini-piles have been found to be a practical, technically correct remedial underpinning method. They can be constructed in limited access areas with very little disruption. Experience indicated that mini-piles installed using a down-the-hole soil displacement hammer would be particularly effective in the "bottomless" Beaumont Clay formations in the Houston, Texas, U.S.A. area. The University of Houston Foundation Testing Facility was ideally suited to perform tests on mini-piles. The availability of extensive geotechnical data and previous pile test results was invaluable in evaluating the mini-pile test data. As expected, the mini-pile test results were consistant with test results from large sized driven piles in the same soil formation.

Jan 1, 1989

By Muhannad T. Suleiman

Temperatures below freezing significantly enhance the soil shear strength and stiffness and to a lesser extent increase the compressive strength of concrete as well as the yield and ultimate strength of reinforcing steel. Consequently, the lateral load resistance of bridge columns supported by drilled shafts becomes dependent on seasonal weather conditions. To investigate the effects of seasonal freezing on the behavior of bridge columns supported by drilled shafts, large-scale field lateral load tests were conducted at 23°C (73.4°F) and -10°C (14°F) on two identical units at an field test site, which consisted of glacial till soil classified as low plastic clay. The bridge column-drilled shaft systems were subjected to cyclic lateral load with the maximum lateral column top displacements reaching approximately ±30 cm (±11.8 in.). The soil at the test site was characterized at different temperatures using unconfined compression tests in the laboratory as well as in-situ Cone Penetration and Pressuremeter Tests. Using these test results, the lateral load behavior of the column-drilled shaft systems were analyzed utilizing numerical models that consisted of beam elements representing the concrete column and the shaft and lateral springs representing nonlinear p-y response of soil. This paper focuses on comparing the calculated responses of test units with different p-y curves that were developed for the soil near the ground surface using the laboratory and in-situ tests. From the experimental study, the response of the unit tested at -10°C (14°F) was found to show 44% increase in lateral force resistance and 0.84 m (2.76 ft) upward shift of the maximum moment location compared to the response of the identical unit tested at 23°C (73.4°F). Theoretical behavior that included the temperature effects on soil, concrete and steel properties provided good correlation with the measured responses when the soil near the ground surface was modeled using the unconfined compression test or the Cone Penetration Test data, but not the Pressuremeter test data.

Jan 1, 2006

By Pasi Korkeakoski

There are about 400 multi-storey buildings founded on wooden piles in the city centre of Turku in Finland. Soil conditions are variable from hard rock to very soft clay. Due to the soil conditions and ground water lowering there are basically four different types of underpinning projects. Under dimensioned cohesion piles in a deep clay layer, decaying cohesion piles, a combination of these two reasons and decaying end bearing piles in a thin clay layer area. Many different execution methods have been used such as impact driving, jacking and drilling and combinations of these.

Jan 1, 2000

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity. Now this important project is in progress and this report describes the special foundation techniques used on the great ship lock Hohenwarthe. Hohenwarthe is a double- bay ship lock of considerable scale, which is notable for recirculating water rather than letting it flow. It includes 44 800 m2 ( 481 720 sq. ft) of up to 55 m ( 180 ft) deep cut- off walls, ground water control, 1248 bored piles with a depth of 22 m ( 72 ft ) serving as foundation and 28 000 m ( 91 864 ft) of soil densification with vibroflotation equipment for ground improvement. In the year 2003 the project shall be completed and all ships can travel from the West to the East through Germany without expensive and time- consuming detours through other canals and locks.

Jan 1, 2000

By Mark X. Haley

Foundation design and construction in Boston has changed dramatically during the past 10 years. Prior to 1985, the primary foundation element in Boston, where deep foundations are required, was driven end-bearing piles. Since 1985, drilled or excavated high capacity foundation elements have been utilized more frequently. This paper will provide a historic perspective of their use and a summary of design parameters for elements installed and founded in the bedrock. TOPOGRAPHY Boston was founded in 1630 by the Massachusetts Bay Company of John Winthrop and his hearty band of Puritans. The settlement was chosen for: ? its safe harbor, ? abundant source of fresh water, and ? peninsula setting offering protection of the ocean on almost all sides with high ground for fortification. These three factors were a direct result of past geologic processes that created the Boston Basin by erosion of the soft bedrock underlying this area as compared to the harder granite rock to the north, west and south. As the glacial ice sheets melted and moved northward, various soil types were deposited. During ice sheet re-advancement the hills and islands of Boston took on their precolonial shapes. The Trimont, consisting of Beacon, Mt. Vernon and Pemberton Hill, rose to 150 ft above sea level with the smaller Copps and Fort Hill to the north and south.

Jan 1, 1994

By Stan Merjan

Composite piles with precast concrete tapered pile tips (TPT Composite Piles - U.S. and foreign patents) are a new and important addition to the piling types available to the construction industry. TPT Piles were invented by Stanley Merjan, Vice President of Underpinning & Foundation Constructors, Inc.. U. F. C. installs these piles in the Northeast United States and licenses piling contractors in other parts of the country. TPT Piles have been developed for use in sandy subsoils at depths to 70 feet or greater. The TPT system (see Figure 1) is simple. A pile stem of conventional material (shell, pipe, steel, wood, precast concrete) is connected to a socket formed in a precast concrete tapered pile tip (TPT). This composite assembly is then driven as a unit by ordinary pile driving methods until adequate driving resistance (established by formula or load tests) is met in a suitable soil strata. This driving resistance develops from the displacement and densification produced by the TPT. Many combinations of tip shapes and stems are available to suit particular job requirements with respect to subsoil conditions and pile capacities. TPT Piles should be considered for use on a wide variety of jobs. The advantages offered by a TPT installation include: ? High capacity piles in marginal soils ? Minimal lengths required to produce these capacities ? The use of conventional pile driving equipment and procedures ? Pile inspection techniques that are the same as for ordinary pile driving Furthermore, TPT piles are economical due to a combination of a low cost per ton of pile capacity and high productivity, both of which lead to significant savings in foundation costs and time required to complete foundation work.

Jan 1, 1987

By Y. Duraisamy

This paper presents the compressibility of tropical peat reinforced with cylindrical cement column. When a cement column installed vertically in peat, its compressibility was reduced because of the hardened skeleton matrix formed by cement particles bonding with adjacent soil particles in the presence of pore water. The effects of diameter, number of columns and cement proportions in cement columns on the compressibility have been investigated in this study. The results indicated that compressibility index Cc and Ca decreased with the increase in diameter of the cement column. Specimens with 45 mm and 60 mm diameter of cement column were cured for 28 days, after which they were subjected to Rowe Cell Consolidation test. Based on the results obtained, it shows that cement columns can successfully reduce the compressibility of tropical peat.

Jan 1, 2007

By Roger Frank

"Abstract After noting the importance of standardization for piles, the European system is described (execution, tests and design, etc.). Some important aspects of Eurocode 7 are outlined (like the role of pile load tests). Finally, the calculation methods in the recent French standard for the design of piles following Eurocode 7 are shortly addressed.Importance of standardization for piles Like for other fields of geotechnical engineering, pile engineering is a complex art. For piles, the challenges are particularly numerous and many things must be mastered properly: - the soil investigation must be serious and adequate (for instance, deep enough!);- the choice of the pile type and the assumed behaviour must be assessed in order to reach a safe and economic design of the overall foundation;- the execution itself (construction and/or installation) deserves special attention and must follow strict state-of-the art rules.The geotechnical engineer, in charge of the design of a pile foundation, must have in mind the parameters linked to the variety of soils, of soil conditions and of pile types. A wide range of strong environmental issues are also to be considered: minimum disturbance during the execution processes, long-duration friendliness of the “inclusions” into the ground (to avoid pollution of the soils and waters, for instance) and respect of the neighbouring structures.Pile engineering plays in a world which is constantly moving and progressing: constructions expand in new difficult areas, actions on piles are more and more important, new execution techniques of piles are developed, research into the complex behaviour of pile foundations has no end, etc. Our views on how piles and group of piles really work are constantly evolving!"

Jan 1, 2014

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By Rajesh Minda

160 numbers of double bulb underreamed piles were constructed based on the safe loads specified in IS code at Tripura. The pile load tests yielded a much lower capacity. A detailed investigation work was carried out to find out the reasons for anomaly. The work included soil exploration followed by extraction of two piles bearing numbers 72 and 151. It was seen that the bulbs were not formed as per specification. Some comments on IS Code have been made at the end.

Jan 1, 1996

By Daryl W. Wurster

The Liberty Bridge in Greenville, South Carolina is a curved, cable-stayed, pedestrian bridge with primary support provided by two towers. The bridge is part of the Falls Park redevelopment. The bridge was originally designed to be supported on drilled piers. Alternately, the bridge was supported on a combination of micropiles and anchor piles because of difficult access and subsurface conditions. The use of micropiles and anchor piles led to improved construction scheduling and reduced costs. Micropiles were used to resist compressive loads. Anchor piles were used to resist tensile forces and to eliminate excessive settlement of pile caps into underlying fill during pre-stressing. This paper describes the site history, bridge construction, site and subsurface conditions encountered, and the decisions that led to support of the bridge using micropiles and anchor piles and foundation construction.

Jan 1, 2006

By R. H. Wright

This paper describes the design philosophy and methods employed in constructing the foundation elements for the Little Britain Project in the City of London. The Contract is a design and construct package for the foundations of a 3-storey basement which will be built using "top-down" construction techniques and is to be carried out by Fairclough Piling and Marine on behalf of Wimgrove Nominees. The Project includes 8000 sq.m. of diaphragm wall and barrettes 139 No. large diameter piles ranging from 900mm to 3000mm in diameter and up to 45m deep, and 9 No. cruciform barrettes for the heaviest column loads. Major factors influencing the design of these foundations include differential settlement, heave analysis and a fast track construction approach. Little Britain will provide 43000 sq.m. of space in two linked buildings which will bridge a new road joining London Wall to Newgate Street. The foundation contract is well advanced and the building is due for completion in the Summer of 1990.

Jan 1, 1989

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By P. A. Neill, O&apos

The caisson foundation for Vent Building No. 6, at the southern landfall of Boston's Third Harbor Tunnel, was installed inside an unbraced concrete cofferdam 250 feet in diameter and about 70 feet deep. As a spectacular engineering feat, the cofferdam itself certainly ranks first. However, the foundation work within was no routine caisson job and made its own contribution to the state of the art. Comprised of 5 ft. diameter caissons socketed 10 to 16 feet in sound rock, it posed serious challenges in logistics, space limitations and time, requiring development of unique, purpose-made equipment. The unexpected discovery of significant depths of shattered rock overlying acceptable sound rock, along with other surprises of lesser import, compounded the problems. How these challenges were planned for, met and overcome is the subject of this paper.

Jan 1, 1994

By Sastry Putcha, Vamshi Vemula, Aneesh Goly, Kumar Allady

Current dynamic testing practice to obtain pile total capacity will not yield optimum capacity due to the strain incompatibility between the side and tip resistances during driving. Superposition of end of initial drive- static tip capacity and the peak static skin capacity during beginning of restrike and adding them is the preferred method. The FDOT method determines independent pile static tip and skin capacities in real time analyzing appropriate blows from the embedded tip and top data of the Embedded Data Collectors (EDC). This data is collected through a wireless radio transmitter, receiver, and laptop software. The approach utilizes EDC tip and top data and nonlinear single degree of freedom system to satisfy force and energy equilibrium with a global genetic inversion analysis. Top impacted energy equals at pile tip as sum of Static, Damping and Inertial energy providing independent tip resistance. With EDC sensors as boundary conditions, pile is divided into desired segments and using global inversion techniques one dimensional equation is solved for independent skin friction for every blow. EDC data compared close static load test results. The EDC - FDOT method has enabled cost effective 100% testing of driven piles cost effective. INTRODUCTION Historical documentation has shown that not only driven piles have a long history of usage but also continues to advance unceasingly till today. Historians placed the first pile driving using timber piles in the 4th century BC. While modern pile driving systematically started around nineteenth century, the credit for conceiving the idea of the applicability of wave equation to driven piles goes to David Victor Isaccs of Australia. His 1931publication “Concrete Pile Driving Formulae” provides the basis for modern pile driving using stress wave theory. He felt that the dynamic formulae then in use lacked the capability of detecting integrity and hence developed stress wave theory. This work was further developed starting in 1938 by W.H. Glanville and colleagues of British Building Research Board as they developed the first solution to the wave equation. But these early efforts have really taken off only with the advent of computers. E.A.L. Smith (1960) published ‘Pile Driving Analysis with the Wave Equation’ and provided first numerical solution to the wave equation. Within few years, the FHWA funded research and in due course this effort ushered the era of externally instrumented pile driving.

Jan 1, 2018

By M. England

A method for the analysis and prediction of single pile displacement behaviour is described. It is the displacement in time, under constant load, based on the use of hyperbolic functions to characterise individual constituents of the displacement-time behaviour. Extensive use of this technique has confirmed its validity in a variety of soils and that consolidation and creep settlement appear to be indistinguishable. The algorithms employed are suitable to model the displacement behaviour from the onset of load to infinite time for all types of piles and surface foundations. Until the advent of computer controlled static load testing, analysis of the displacement-time characteristic during pile load tests has been hindered by the quality of the data recorded and inconsistency of loading. This has hitherto made the development of suitable behavioural models very difficult. Understanding the soil deformation within a proper time framework allows the subject of pile instrumentation and testing to be developed. The equipment required is basically a computer controlled loading and pile head displacement measuring system which allows accurate analysis of the settlement characteristic in almost every situation.

Jan 1, 1993

By Donald A. Bruce

The paper reviews aspects of the construction and performance of prestressed ground anchors installed in soils and weak rocks. Attention is focused on good practice for drilling, tendon fabrication and handling, grouting, stressing and testing. Regional variations - not always logically justified - are described. The performance of anchors in a variety of geological conditions is illustrated with reference to recent full scale test programs. 1. Introduction In the United States there has been steady growth in the use of prestressed anchors in materials other than competent or hard rock, in the years since their introduction in the late 1960's. This expansion has to a large extent been driven by specialty geotechnical contractors who both imported foreign developments and conducted their own basic researches, in locally prevailing conditions. With such data and experience, these engineers have had the confidence to promote "alternative solutions" for difficult earth support problems to receptive designers and owners. In turn, being engaged in the details of design and performance monitoring has given these parties the close exposure necessary for the real transfer and understanding of the technological concepts, and this knowledge has generated positive feedback for the contractors.

Jan 1, 1991

By Robert R. Morrison

Alberta Piling Contractors very rarely are required to perform major marine construction in the prairies, so it became as a big surprise to AGRA Foundations Limited to be invited by Transalta Utilities Corporation to bid on a major marine project for the Sundance Cooling Pond Expansion at Lake Wabamun, Alberta. Even more of a shock, the work had to be undertaken during Alberta's harsh winter conditions with temperatures plunging to -30 C. Not a happy situation for prairie construction workers to be in, working from barges in the middle of a lake in the dead of winter. However, it is well known that prairie boys make the best sailors.

Jan 1, 1997

By Mohammed Sakr

The use of helical piles for permanent foundation applications has become a practical and feasible alternative to the traditional cast-in-place concrete or driven steel piles. Research and development, installation equipment and manufacturing improvements in the helical piling industry have led to this trend. Moreover helical piles are typically smaller in size and weigh less than traditional piles, and require relatively smaller equipment and therefore it is a cost effective option. The latter is a very attractive feature for foundations installed in remote sites across Alaska. This paper presents full-scale pile load test results of helical piles and driven steel pipe piles installed in a site located in Anchorage, Alaska. Four full-scale pile load tests were carried out including two axial compression and two uplift load tests. Both helical piles and driven steel pipe piles were installed and tested at the same site under similar conditions to provide a direct comparison. The results of the full-scale load tests indicate the superior performance of helical piles compared to driven steel pipe piles. This paper describes the pile installation and test setup, presents the test data, and discusses the results.

Jan 1, 2009