Search Documents

By Li Xibing

The In order to mine safely with reasonable cost, it is necessary to research the fracture characters of backfill and its matches with rock mass. Four kinds backfill with cement-tailing ratio of 0.250, 0.125, 0.100 and 0.083 respectively were tested, and basing on stress-strain curves tested, the deformation characters and fracture laws as well as the damage constitutive equations investigated with damage mechanics whose calculating results are coincided with experiment results well were proposed. The results of damage analysis show that there have different damage characters in different backfill, e. g. the lower the ratio of cement to tailings the lower the damage values when stresses reach to peak value; the lower the content of cement the more rapid in damage and the more abrupt in breakage process. In addition, using catastrophe theory, an energy model was proposed for backfill and rock mass acted each other in mechanics, and the unstable condition of the system was obtained. Research results show that the higher is the stiffness of rock mass the more stable the system, and the lower is the ratio of cement to tailings, the more unstable the system will be. Further more, according to the catastrophe model proposed, the reasonable matches between backfill and rock mass were researched, and a calculation formula that designs reasonable strength of backfill during mining was put forward. It has been proved by practice that the model and theory researched in this paper can guide filling design in mining. Keywords: Cemented tailings backfill, constitutive equation, catastrophe theory, match of backfill and rock mass

May 1, 2007

By Muhammad Zaka Emad

Cemented rockfill (CRF) plays a vital role in pillar-less mining. Many factors are associated with optimum design of a CRF material. Factors like strength, placement method, mixing, curing time, water content, binder contents, binder composition and additives require to be studied for appropriate rockfill design. The most important factor is strength of a CRF. The design engineer considers fill strength requirements (FSR) for the estimation of CRF strength requirements. Inappropriate CRF strength can cause excessive ore dilution. The recent studies on CRF practices at some of the Canadian mines revealed the most common flaws. Comparison of different types of fill determined that most of the failures occur in cemented rockfill, and the compressive strength can be improved by small addition of sand and mine tailings. This work discusses the studies on determination of unconfined compressive strength, Young?s modulus, density and water contents of CRF being placed in the excavated stopes. It was found that the CRF properties were largely influenced by the variation in gradation and curing time. The 7% binder content improved compressive strength of rockfill significantly but it has an influence on the economics, whereas 4% and 5% binder contents are better choices. The maximum Young?s modulus values were obtained at 28 days curing time for most of the samples.

May 1, 2011

By Z. D. Hora

Commercial production of barite commenced in British Columbia in 1940; shipments have been recorded from ten deposits, of which four are particularly significant: The Brisco, Silver Giant, Parson, and Mineral King mines. Parr of the barite production is a by-product of base metal deposits in which barite is a major gangue mineral. About one hundred occurrences are known. COMMERCIAL production of barite in British Columbia dates back to 1940. Production volumes rose and fell and reached 39,900 tonnes in 1972. The main producer is Mountain Minerals Limited . There are two principal areas of barite deposits in British Columbia: ( I) The southeast part of the province along the Rocky Mountain Trench , which is the source of all production to date. (2) Stratabound occurrences in northeast British Columbia in the Gataga-Ketchika rivers and Muncho Lake areas which are not yet developed. Of the approximately one hundred reported barite occurrences, only ten have recorded commercial shipments, some of insignificant amount. So far, four deposits have proved to be important producers: Brisco, Silver Giant, Parson and Mineral King. The Mineral King property is situated near the confluence of Toby and Jumbo Creeks, 35 km southwest of lnvermere. The lead-zinc-copper-iron-barite deposits, as described by Fyles (1959, 1962), replace Proterozoic Mount Nelson dolomites of the Purcell system on the limb in the trough of a complex, tight syncline. The mine operated from 1954 to 1967 and 2,097,900 tonnes of baritic ore that was processed for base metal concentrates and also produced 22,680 tonnes of by-product barite. Since 1970, some 136,000 tonnes of barite have been recovered from the old tailings pond. The deposit is now considered depleted. The Silver Giant mine is located 10 km northwest of Spillimacheen. Barite and lead-zinc sulphides replace Cambrian Jubilee limestone near their contact with the overlying Ordovician McKay slate. Mineralization is located in the nose of an overturned plunging anticline. Between 1951 and 1957 800,000 tonnes of baritic ore were processed for lead and zinc concentrate. After 1959 barite was also produced , first from open pit, and later from reworked tailings. Up to 1979 production of barite totalled approximately 180,000 tonnes. Two other producing mines in the area are descri bed by G.R. Manson (this volume). Large, bedded stratabound barite deposits are reported from northeastern British Columbia. Six major shale-hosted Industrial Minerals in Canada lead-zinc-barite occurrences are known in the Devonian Gunsteel Formation. These are: Driftpi le Creek, Mount Alcock, Cirque, Pie, Fluke and Elf. In addition, numerous occurrences of strati form blebby or nodular barite and locally massive white crystalline barite are known from the Driftpi le Creek and Ak ie River districts in Gunsteel shale and from the Kechika, Road River and Ware map areas from Silurian siltstone . The size of these deposits is impressive; the baritic horizon at Mount Alcock is reported to be 25 to 30 m thick , and dri ll ing results from the Cirque deposit indicate reserves of 30 mi llion tonnes of baritic lead-zi nc-si lver ore. Similar bedded barite deposits are also reported from Midway area, near the Yukon border.

Jan 1, 1984

By P. W. A. Walker

"The Riviera tungsten occurrence in the Cape Province of South Africa was discovered in October 1979 as a result of stream-sediment panned concentrate sampling. The Cape age granite and late Precambrian Malmesbury Group carbonates and chlorite schists which it intrudes and which host the mineralization are covered by between 10 m and 30 m of Tertiary/Recent alluvium and clay. The scheelite/powellite and molybdenite mineralization occurs in a greisenized granite cupola with an overprint of porphyry-type alteration as well as in minor skarns. The ore reserve is estimated to be 46 million tonnes at an average grade of 0.216% W03 and 0.020070 Mo. The deposit is uneconomic at current tungsten prices. IntroductionDuring the 19705, Union Carbide Corporation was a major producer, processor and supplier of tungsten and derivative products to end-user manufacturing industries. The corporation owned and operated two tungsten mines in the United States, and one in Brazil, and operated a plant in the United States which produced ammonium paratungstate (APT) which is an intermediate product in the production of tungsten wire and tungsten carbide for cutting tool insets and hard facings. In 1975 the three mines were ageing with short-life reserves and high production costs. The world market for tungsten was buoyant and prices, in constant dollar terms, had risen steadily over the past 15 years (Fig. 1).It was against this background that a decision was made to explore for tungsten in North America, South Mrica, Australia and Brazil."

Jan 1, 1994

By A. W. Johnston, R. E. Barrett

"The Central Patricia mine is in the greenstone belt north of lake Sc. Joseph in northwestern Ontario. It is 90 miles north of Allanwater on the Canadian National railway and 220 miles east of the Manitoba boundary. The unusual feature of the ore of this mine is that the gold does not occur in quartz but in sulphide minerals filling fractures in iron formation.AREAL GEOLOGYThe rocks of the area in which the mine occurs belong to the Early Precambrian. They consist · of andesite lavas and tuff interbedded with greywacke-like sediments and iron formation . A siliceous phase of the sediments lying north and south of the greywacke enclosing the ore-bearing iron formation in places resembles a sheared and sericitized quartz porphyry. This is shown in the legend of Fig. 1 as quartz porphyry and quartzite, but it is possible that the quartz porphyry-like phase is sediment. A northwest- striking dyke of diabase crosses the property 3,000 feet east of the shaft ( Fig. 1).IRON FORMATIONAlthough there are numerous bands of iron formation in the v1cm1ty of the mine, ore has been found to date in only one main and two lesser zones. The iron formation bands range in width from a few inches to 60 feet, and are interrupted along their strike by gaps that are parallel and rake to the east at about 65°. The iron formation is definitely banded and laminated."

Jan 1, 1954

By R. J. McLeod

"Grinding at Giant Yellowknife is done in two stages. The first stage consists of two ball mills in closed circuit will: mechanical classifiers, the classifier overflow goes to flotation. The tailings from this flotation circuit are separated into slime and sand portions, the slimes go to an additional flotation circuit while the sand portion goes to the secondary grinding mills.Milltronic automatic sound control units were installed on each of the two primary ball mills and put into operation September 3, 1966. After about two months adjustments to the control units the operators were taken off the grinding circuit on November 1, 1966. The operators duties were taken over by the automatic control units while miscellaneous work was taken over by the helpers in the mill. The labour saving by the installation is approximately $2250.00 per month.After a short period of operation it was apparent there was a slight change in grind. The screen analysis of the primary classifier overflows for the period May to August 1966 averaged 62.23% minus 200 mesh while for the period September to December 1966 averaged 62.0% minus 200 mesh. This is a slight coarsening of the grind. The change in the primary grind has manifested itself also in the screen analysis of the final grind. Before automation the final grind was 80% minus 200 mesh, while after automation it was 7 5% minus 200 mesh. A change of grind was also noted in the flotation concentrates. Before automation the screen analysis of the concentrates was 35% plus 200 mesh and 50% minus 3 25 mesh. A ft er automation it was 35% plus 200 mesh and 47 .5% minus 325 mesh. In other words the grind got coarser or perhaps we should say there was less overgrinding. Another significant change took place in the assays of the slime and sand portion of the primary flotation tailings. It was usual under manual control for the slime portion to assay higher in gold than the sand portion. The reverse is now true."

Jan 1, 1967

By Chris D. Veldhoen

If you ask most diamond drillers if they have ever encountered methane gas, the answer would probably be yes. This paper explores a serious methane gas explosion that the author experienced while diamond drilling at a northerly Ontario mine. It is hoped that by documenting this event, people may be alerted to the hidden danger posed by confined methane in underground workings. Methane gas tends to be a problem the deeper you get in any Canadian gold mine. Common procedure when encountering methane is to take readings at the collar of the hole and at different lengths from the source. Monitoring continues until the readings drop below 0.25 ppm. Methane is a tasteless odorless gas that is usually locked up in the seams of the rock or is a product of decaying organic material. Occasionally, the gas is released abruptly over a short period of time. Sometimes the gas can continue to vent for months or even years. In small concentrations, methane is relatively safe. In concentrations under 0.25 ppm methane gas is considered safe to work around. Concentrations over 0.25 ppm can become dangerous. During the summer of 2001, Chris Veldhoen was drilling at a gold mine in Ontario. There were three electric hydraulic diamond drills on the 39 meter level, approximately 5200 feet deep. Two Longyear LM 55 drills were about 40 feet apart and another LM 75 was about 2000 feet away. The two LM 55?s were set up to drill holes no deeper than 350 meters. All three drills had been set up on the same spot for more than a month. None of the three drills had ever encountered methane gas in the entire time they had been drilling on the level. On the day shift of July 13 2001, the driller on Chris? cross shift hit a small pocket of gas. He tested the hole and got a reading above 0.25 ppm. He proceeded to rope off the area with a ?DO NOT ENTER - METHANE GAS? sign and a rope denying access beyond the sign. On Saturday, July 14, Chris was instructed to install a Margo plug in the hole that was emitting methane gas. Methane is usually odorless, but occasionally when encountered underground, is accompanied by a rotten egg smell. As he walked to the drill, he could not smell methane gas. He proceeded to test the hole and got a reading of 0.22 ppm methane. This number was in the acceptable range for drilling, but he plugged the hole anyway.

May 1, 2004

By Tommee Larochelle, Henry Kasaini

"Simulation of rare earth element solvent extraction processes for plant design and optimization is complex, requires extensive bench scale and pilot scale testing, and is traditionally performed using proprietary algorithms. The complexity of simulation is mainly due to traditional simulation software solvent extraction modules not being designed to simulate rare earth separation processes because of the interaction between each element. This paper presents an alternative method for designing and optimizing rare earth element solvent extraction separation processes using METSIM to converge each stage of the battery individually until the full battery reached ultimate convergence. A feed-forward controller is used to control the organic to aqueous flow ratio feeding the solvent extraction modules. This method minimizes the complexity of simulating such processes by using inexpensive batch solvent extraction data, and allowing for rapid theoretical optimization, by varying the process configuration and parameters from a graphic interface instead of the traditional code-based interface of most proprietary models. Comparison of the model predictions to pilot plant data reveals that the method can be used to accurately model rare earth solvent extraction processes, as illustrated by its application in the development of Rare Element Resources innovative process.INTRODUCTIONThe Rare Earth Elements (REEs) consist of 16 metals, specifically the 15 lanthanide elements and yttrium, which is typically found in the same mineral deposits as the lanthanides. Scandium can be associated with the rare earth elements, but is usually only present in trace amounts, and therefore omitted. The term “rare earths” originates from an old term used to designate minerals (earths) and their believed scarcity upon their initial discovery. The rare earths designation is now considered a misnomer because it was demonstrated that the crustal abundance of some rare earth elements, such as cerium, is known to be higher than many common metals, such as copper. However, enriched deposits are fairly uncommon compared to other similarly abundant metals. The REEs are typically divided into groups commonly consisting of light rare earths (LREEs), medium rare earths (MREE), and heavy rare earths (HREEs). Light rare earth elements include lanthanum to neodymium, medium rare earths include samarium to gadolinium and the heavy rare earth elements include terbium to lutetium, and yttrium. The REEs exhibit similar chemical characteristics and are usually extracted from the ore and processed into a mixed rare earth concentrate. The rare earth concentrate requires further processing in order to separate the REEs from each other and produce a series of single element products."

Jan 1, 2016

By Eva Surová, Molák. Bohumil, Márta Polgári

The Úrkút rhodochrosite deposit and Branisko Mn showings (rancieite, manganiferous calcite), located in Lower Jurassic marine sedimentary rocks with black shale, were studied by organicgeochemical methods. Both depositional localities were affected by the Lower Jurassic Toarcian anoxic event. UrkUt shales are rich in organic matter (av. 2.94 wtOJo total organic carbon), the composition of which indicates derivation mainly from marine sources, with some terrigenous component. The shales matured in a bacterially active environment under reducing conditions of diagenesis-catagenesis. Branisko shales (~0.2 wt % TOC) with lenses of Mn oxide ore were weakly metamorphosed and their organic matter thermally degraded. The model for Mn carbonate ore formation envisages reaction of Mn derived from sediments, with carbonate generated by a bacterially mediated process of decomposition of organic matter that also involved Mn reduction.

Jan 1, 1992

By Tyson C. Birkett

Initial indicator mineral sampling covering 425,000 square km of northern Quebec and subsequent follow-up of positive results convinced the Ashton ? SOQUEM joint venture to acquire mineral rights to 380,000 hectares prospective for diamond in late summer, 2000. Drilling in 2001 and 2002 identified eight kimberlitic bodies, all significantly diamondiferous. Commercial size stones (retained on a square mesh sieve with openings 0.85 mm) and encouraging grades have been returned by several bodies tested to date: The Renard bodies are formed by steep-sided breccia pipes with kimberlitic matrix surrounded by irregular outboard breccia zones within country rock. These bodies were emplaced in high-grade metamorphic rocks of the Superior Province of Archean age. Orthogneiss with lesser tonalite hosts the breccias, although regionally paragneiss is also present. Diatreme facies portions and nearby country rock are intruded by minor to major (Renard 1) amounts of hypabyssal-facies kimberlitic rock. Renard bodies are macrocrystic, with large olivine crystals set in a groundmass of olivine, phlogopite, monticellite, spinel, carbonate, apatite and serpentine. Proximity of various Renard bodies, with most in a core area of 0.5 square km will allow planning of an efficient mining operation. Geophysics, especially magnetic surveying, has contributed to identifying bodies of kimberlitic rock.

May 1, 2003

By Jose A. Jimenez

"Mining operations generate an enormous amount of data that is difficult to organize, analyze and act on. These data require an extremely broad range of experts to investigate and manage the cross-disciplinary information. The data collects in paper files, diverse databases, historians, stand-alone applications, and excel files. This collection of sources represents everything from monthly, weekly, or daily inputs to real-time feeds or sporadic unscheduled entries. With the operational complexities ever increasing and fewer engineers per mine, an efficient operation is becoming more and more challenging. Engineers are typically burdened with data collection, clean up, and administrative efforts leaving very limited time for engineering assessment and/or optimization analysis. Often optimization becomes limited to the analysis of equipment uptime through existing field automation systems. A great portion of the field data is tucked away in historians seldom reaching those engineers who might leverage the data. Few mine operators have the time or budget to re-architect their operations data collection or management practice, so solutions must enable improvements without requiring expensive or time-consuming implementation. This presentation highlights examples where the aforementioned challenges are addressed using a solution framework designed to enable: 1) data integration and connectivity, 2) monitoring and opportunity recognition, and 3) engineering workflow automation. The initiative extends the concepts and success proven in the automation market segment to all disciplines across the mine operations. INTRODUCTIONThe mining industry by its very nature spends a great deal of its capital on equipment maintenance and replacement. In addition, periodic shutdowns due to equipment failure are typically very costly in terms of interrupted operations. Keeping mining equipment running at peak performance and avoiding costly shutdowns can make a huge difference in the overall return from mining operations. Today, information can be make available that can go a long way towards spotting equipment issues and permitting timely intervention to avoid costly unplanned shutdowns. That said, gathering all of the information from numerous points on many different pieces of equipment necessary to enhance overall equipment effectiveness presents its own daunting issues."

Jan 1, 2016

By Brett Triffett, Mark Weidenbach, Christopher Treloar

OZ Minerals owns and operates the Prominent Hill copper-gold concentrator in South Australia, built in 2008 and commissioned in early 2009. The concentrator operates via semi autogenous grinding in a thirty four foot ThyssenKrupp Polysius mill followed by a twenty four foot Polysius ball mill in closed circuit with hydro cyclones, designed for an ore throughput of eight million tonnes per annum. The main aspects of designing the circuit are discussed along with the issues faced in the early stages of operation. A review of the optimization strategy applied to the milling circuit such as cyclone optimization, advanced process control strategy implementation and reline management to improve availability is then discussed highlighting areas of significant process improvement that have seen the plant exceed nameplate throughputs above nine million tonnes per annum.

Jan 1, 2012

By J. A. Drozdiak, A. Bamber

In this paper we examine, through pilot-scale testing, the possibility of operating a circuit comprised of two stages of HPGR comminution, followed by grinding through a horizontal stirred mill. In order to assess whether the novel circuit design could achieve the reduced energy requirements indicated in the literature, two more-established circuits, a cone crusher / ball mill and an HPGR / ball mill, were examined using a combination of testing and flowsheet simulation. The results showed that, based solely on the specific energy requirements for comminution, the HPGR / stirred mill circuit achieved a reduction of 9.2% and 16.7% over the HPGR / ball mill and cone crusher / ball mill circuits, respectively.

Jan 1, 2012

By Carlos Nieble

Ferteco Mineracao, belonging to the CVRD group, is one of the several iron ore mines in the south east of Brazil. Some of these mines have pit walls of over 350-m height and operations under difficult geo-technical conditions are steadily increasing. In order to mine the 15 million tonnes of high grade hematitic ore remaining in the Fabrica pit, Ferteco had to deal with the following restrictions: Warrant power to its concentrator and pellet plant, relocate the load-out rail road loop, stabilise a poor phillyte slope, relocate a creek on a bench, lower the water table and mine at maximum angles at a slope with phillyte and loose itabirites directly under the rail road loop. Considering these aspects, 3 stages of operations were designed, considering a safe operation, but with the lowest possible security factors at the last mining stage, before the pit would be filled in again with tailings. Stage one above the rail road loop and below the high tension power mast, where the poor phillyte slope was secured by a flexible retaining wall, using old rails and anchors up to 27 meters (80ft) with a working pressure of up till 30 tonnes and stage two with different slope angles, and deep wells, high wall blasting perpendicular to the highwall with relief holes and rerouting the creek in steel half culvert and stage three, the filling in with tailings and recuperation of the deep well pumps. Following studies and analysis were made: Geotechnical and geological studies of all rock formations including rock strength test, a hydrological study to define the lowering of the ground water level, slope stability analysis for every bench and all possible combination of benches, definition of blasting parameters close to the pit slope, a monitoring plan, including topographical movements, vibrations due to blasting, piezometers and pressure cells as well as a plan how to fill up the pit again with tailings in combination with the rising of the ground water level. A close co-operation between the geo-technical consultant, pit operations, the blasting contractor and the geological department resulted in an operation without any incidents, lowering the pit with an additional 3 benches and mining an additional 5 million tonnes of high grade ore.

May 1, 2003

By I. Osvath, I. Gombköto, G. Mucsi, Z. Molnár

"In the present research, a deposited brown coal fly ash was used as raw material for geopolymer. The reactivity of the fly ash was altered using mechanical activation, which is one of the promising methods to improve bulk and surface reactivity. The mechanical activation experiments were carried out in a high energy density mill using 5 m/s circumferential speed, and various residence times (1, 3, 5, 10, 15 and 60 min). The effect of mechanical activation on particle size distribution was measured by a laser particle size analyzer and structural changes using FT-IR. Geopolymer samples were prepared from mechanically activated fly ash with an alkali solution. The progress of geopolymerisation was monitored using an Isothermal Conduction Calorimeter. The heat flow curve obtained indicated that reactions were more prominent and started much earlier in the mechanically activated samples. This observation is further supported by the compressive strength results which also improved in geopolymers using mechanically activated fly ash. Based on the obtained results, it can be inferred that mechanical activation is a possible way to enhance the reactivity of fly ash and consequently properties of resulting geopolymers.INTRODUCTIONCoal fired power plants generate fly ash and slag in huge amount worldwide, about 780 million tons/year (Heidrich et al. 2013). Due to the relatively low utilization rate, enormous quantities of these wastes are landfilled in ponds. The fly ash is the finest grained particle fraction of the solid ash, which is transported with flue gas, and removed by electrostatic or bag filters. The fly ash has pozzolanic activity, it does not react with water, but in the presence of calcium hydroxide solution hardens and solidifies, producing a reaction product practically insoluble in water (Opoczky, 2001). The most important property of the fly ash regarding geopolymerization is its reactivity, which depends on the chemical and phase composition, the dispersity (specific surface area, particle size distribution), and the morphology of the fly ash particles, and determined by the physical properties and chemical composition of the fly ash. Geopolymers concerning their chemical structure are polysialates, where the sialate (silicon-oxoaluminate) network is built up from the bonds of Si-oxide and Al-oxide by sharing oxygen atoms (Davidovits, 1988)."

Jan 1, 2016

By M. McKim

"Due to the fact that there were no formal papers submitted for this session we can only print the discussions of the papers. a) Maqnetic Mill Liners : M. MckimE. MarcotteFalconbridge LimitedReplyIn looking at the slides on magnetic mill liners a question comes to mind, particularly in the case of a large diameter mill using large grinding media, concerning the potential hazzards which may exist from large chuncks of steel hanging in the mill. Would you comment.The magnetism was sufficiently strong from liner to liner to hold ........................ .(We are sorry but we could not transcribe the full reply to this question as no microphone was used by the speaker and i't was impossible for us to complete the rest).·"

Jan 1, 1984

By Murray W. Grabinsky

This paper considers thickening mine tailings to dense non-segregating slurry or paste for surface disposal. The driving motivation for this initiative is the elimination of ponds, reduction in containment dams and significant decrease in water being sent to the tailings basin. This inherently reduces risks of environmental and structural failure. Some of the engineering challenges in creating a stable stack of thickened or paste tailings are identified, and possible field and laboratory testing techniques in support of design are discussed. Finally, the integration of monitoring activities into the ongoing management of the surface disposal site is considered.

Nov 1, 2002

By F. Shi

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT’s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

Deformation is a critical indicator required to evaluate the structural safety, stability, and integrity. For example, the deformed shape of a building structure is a key parameter that needs to be measured and tracked during laboratory testing or post-disaster inspections. However, existing techniques used for the deformation measurement and tracking do not have all the desirable characteristics, such as: reliability, accuracy, low-cost and simplicity of tools installation. In order to address this issue, a novel method has been proposed in this study. The method consists on using the image processing technique to automatically measure and track the deformations of concentrically braced frame (CBF) structures. Accordingly, the critical points in a CBF structure are first identified and the topological configuration of the structure is retrieved. The points and topological configuration characterize the basic shape of the structure. In this way, the deformation of the structure can be determined by measuring and tracking these points and their topological configuration. To show its effectiveness, the proposed method has been tested against the manual deformation measurements.

Aug 1, 2013

By S. Y. Mostowy, P. W. M. Shibley

"When Texas Gulf Sulphur Company discovered the Kidd Creek ore body in 1964, a crash program began almost immediately for the design and construction of a modern concentrator. It was necessary to mill two distinct ore types; one containing copper and zinc, the other lead, silver and zinc minerals. The final concentrator design was to handle 9,000 tons of ore daily in three circuits. One circuit was to treat copper-zinc and another lead-zinc ore exclusively on a permanent basis. A central circuit was designed with adequate flexibility to treat either of the above ore types in accordance with planned mining schedules. Ecstall Mining Limited, a wholly owned subsidiary, now operates the mine and concentrator complexes for Texas Gulf. The mine is located 15 miles north of Timmins and the concentrator 15 miles to the north-east along Highway 101. The ore is hauled from the mine to the concentrator over a 17-mile railroad. Initial milling operations began in November, 1966.1 - ABSTRACTThis paper deals with bulk reagent handling at the Kidd Creek concentrator. The reagent section at Kidd Creek has operated excellently since milling began in 1966. The bulk handling techniques are satisfactory. They have contributed substantially to good working conditions, economical practices and metallurgical efficiencies. The bulk handling features described should be considered in existing and proposed concentrators."

Jan 1, 1970