Search Documents

By Forrest A. Kerr

Northern British Columbia is a term which probably conveys to various individuals quite different meanings. To the average person it signifies an area of indefinite size and indefinite position which may start at Prince Rupert, Stewart, or somewhere else, and end at Alaska or .the Yukon. Many people, in their conception, fail to encompass in their mind's eye that vast tract of land lying ~o the east of the panhandle of Alaska. Few realize that the area north of an east-west line through Stewart represents more than one-third of the Province and is, of course, the part most appropriately designated as northern British Columbia. This section, more especially the northernmost 100,000 square miles, from political, geographic, and economic viewpoints stands isolated perhaps more than any other part of British Columbia. Unlike the rest of the Province, it has no coast line, being cut off from the Pacific ocean by a narrow strip of Alaska. It is bounded on the north by the Yukon, and on the east by Alberta. In the south this northernmost 100,000 square miles is limited by a divide of rugged mountainous country separating the drainage basins of the Stikine and Liard rivers from those to the south.

Jan 1, 1929

By E. V. Manlapig, U. Erol, V. Ross, K. Tshimanga

Lonmin RoM ball mills are treating two types of feed ore produced by conventional mining and mechanised mining methods. It was reported that reduction in mill throughput was observed when treating the mechanised mining ore. Detailed grinding surveys were conducted for troubleshooting. Ore samples were collected for breakage characterisation using a JKRBT based on different particle density components. XRD analysis was conducted to investigate the association of minerals with density components. The plant surveys and the breakage characterisation tests all suggested that the two mining methods did not significantly affect either the ore breakage properties or the RoM mill performance. Instead, the mill discharge open area exerted a remarkable influence on mill throughput. The RoM ball mill operated at Lonmin K4 Concentrator has been proven to be a versatile mill that performed stably with variations in feed size distribution and feed ore changes by different mining techniques. The reasons are elucidated by the multi-component breakage characterisation and the plant surveys data.

Jan 1, 2012

By Laxman M. Amaratunga, David N. Yaschyshyn

"In the mining industry several types of fills are used for backfill operations. They are broadly categorized into three basic types: rock fill, hydraulic/slurry fill, and paste fill. Recently, paste fill has become the popular alternative for backfilling because of its many environmental and operational advantages including its ability to use total tailings, both fine and coarse fractions.Amaratunga and Annor (1989) first presented the concept of agglomeration of fine tailings, which are otherwise excluded from backfilling, for utilization in backfill as a readily available supplementary fill material. Previous experimental work investigated the use of agglomerated fine gold mill tailings in low density slurry fills (60 -70% pulp density), consisting of varying agglomerate and tailings compositions.This paper presents the ongoing research into utilizing these agglomerates in a high density paste fill (70 -85% pulp density). Various binder dosages, curing period and combinations of pellet to tailings ratios were studied. Slump of the raw fill and compressive strength of the cured fill were examined. Results from the above study indicate that agglomerated tailings paste fill (ATPF) has superior strength characteristics when compared to total tailings paste fills.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. These tailings consist of a coarse fraction and a fine fraction and can be either reactive (acid generating) or non-reactive. Most mining operations utilize the coarse fraction for backfilling while the fines have been traditionally disposed of in surface tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10 - 30% w/w of >45 µ,m) in the fill. This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused portion of fine tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMD) seepage from these ponds has proven to be a costly environmental problem and long term liabilty.One practical method to reduce the environmental impacts associated with the tailings pond and to modify the physical and chemical properties of the fine mill tailings so that they can be utilized and disposed of in an environmentally safe manner through surface or underground applications is through agglomeration using the Cold-Bond Tailings Agglomeration technology (CBTA). Amaratunga and Annor (1989) first presented the concept of agglomeration of fine tailings for use as coarse aggregates for underground backfill, gravel or surface covering material. CBT A reduces the necessity of impounding tailings on surface while providing a suitable coarse aggregate resource material for practical use. Although the CBT A technology has been mainly limited to pelletization agglomeration alone, other forms of agglomeration like pressure agglomeration which include the techniques of briquetting and extrusion have also proven successful (Amaratunga, 1995)."

Jan 1, 1996

By Carlos Antônio de Morais, Renata Dias Abreu

The present work describes a study of the separation of terbium and dysprosium from heavy RE concentrate through a solvent extraction circuit in a counter-current system. As the efficiency of the REE extraction by acid extractants rises with the increase of the atomic number of the element, the aim of this work is to extract the elements with higher atomic number maintaining Tb and Dy in the aqueous phase. Thus, terbium was separated first with subsequent separation of dysprosium. The experiments were carried out by using IONQUEST®801 as the extractant and a REE-hydrochloric liquor as feed solution. The optimum operational circuit in terbium separation was comprised of 37 stages: extraction, scrubbing, stripping, and solvent washing. For the dysprosium separation 39 stages were required. Terbium separation over 92% with over 95% purity and a Dy separation over 97% with over 95% purity were obtained.

Jan 1, 2014

By M. I. Kalashnikova, Y. M. Shneerson, E. E. Zhmarin, Y. V. Degtiarev, E. M. Vigdorchik

Separation of a magnetic fraction from nickel concentrate following matte flotation, and its treatment in a separate circuit enable reduces precious metals losses. The magnetic fraction is treated in two stages of oxidative leaching: atmospheric and pressure leaching. A study of the atmospheric stage, using mathematical modelling, is described in this paper. The mathematical model and experimental data were used to carry out industrial process calculations. The model enabled extrapolation of the results of batch laboratory test to industrial-scale continuous processing and the selection of optimal process conditions and large-scale equipment. In December 2004, commercial oxidative leaching tests were performed on the magnetic fraction at the Severonickel Plant (Monchegorsk, Russia). A comparative analysis of the mathematical modelling results and the actual process parameters is presented.

Jan 1, 2005

By Kazem Oraee

Implementing stable final pit walls in open pit mines during the open pit design phase and mine exploitation has become one of the most important concerns of mining engineers in recent years. Failure of mine walls can potentially cause loss of life, roads blocks, and damage to mining machinery, temporarily or permanently halt production at the face and in the worst case scenario, close the mine. Thus, the role of creating stable mine walls is crucial to safety and general operations of mines and any effort to optimize this process has great economic value for mine operators. This paper aims to illustrate the technical aspects of use of the successful presplit blasting method in metal open pit mines. It also shows that using this approach not only increases safety in mines through wall stabilization, but also will boost economic profits by savings in stripping ratio. In this regard, appropriate practical concepts for designing the drilling and blasting patterns and the role of selecting the correct drilling rigs are elaborated in detail through conducting a case study in Chador Malu iron ore mine in Iran.

Aug 1, 2013

By N. Aydogan, H. Dundar, Å. Partapuoli, A. Fredriksson, P. Wikström, K. Tano, G. Adolfsson

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By Karl Houseley, Dr. Robert J. Chapman

"A gravity concentration process has been applied to ores from the Clogau Mine, north Wales, the Tyndrum deposit, central Scotland and an alluvial ore from Leadhills area of Scotland. In the case of the Welsh ore and the alluvial deposit the gold grains in the concentrate and tailings streams have been characterised in terms of their three dimensions.In the case of Welsh ore, the thickness of a gold grain has been shown to be the single most important factor in determining behaviour in a gravity concentration operation. Six indices were used to quantify the overall geometry of the gold grains and those which incorporate a thickness term have proven to be effective in predicting the destination of gold particles within the concentration circuit. It is proposed that the most simple of these, the Heywoods flakiness ratio, has potential for the control of milling operations as an alternative to the established practice of characterising the size of the mill discharge.The effect of grain geometry on the recovery of fine gold has been studied using Tyndrum ore. The recovery of gold by gravity concentration increased from 20% to 70% when the criteria used to design the milling operation was the prevention of over grinding of gold grains.The destination of alluvial grains in the concentration circuit did not show such dependence on shape, and this has been attributed to the effective classification of all the gold grains in the sample by fluvial action producing a population of similar geometric characteristics."

Jan 1, 1996

By Anthony P. Makuch

Dynatec Corporation is an integrated mining services company, providing mine development, operations management, engineering, drilling and metallurgical services to the North American mining industry. Dynatec was the contract operator of the Ken Snyder Mine in Midas, Nevada from start of production in January 1999 to September 2001. This paper summarizes Dynatec?s experience and approach to the use of longhole stoping methods for mining to widths of 1.3 to 2 metres in a steeply dipping narrow vein orebody.

Oct 1, 2001

By V. I. Peresypkin, A. Y. Lein, N. S. Bortnikov, Yu. A. Bogdanov

"Abstract - The lipid component in hydrothermal deposits of the Logachev vent field, at 14°45_N of the Mid-Atlantic Ridge (MAR) and Broken Spur vent field, at 29°N of the MAR, was studied. Biochemical, gas chromatographic (GS), and molecular mass methods (GC-MS) research established the mixed nature of the organic matter (OM) including phytoplanktonogenous, chemosynthesized lipids, and lipids of questionable origin. Specific local conditions around the sulfide ores of the black smokers (absence of free oxygen and presence of reduced copper, which prevents OM degradation) facilitate the preservation of biogenic material, including bacteria. The main differences between the lipid compositions of the hydrothermal deposits of these two vent fields relate to the variable nature of hydrothermal circulation systems.At the 14°45_N vent field, high-temperature hydrothermal fields are forming due to the reaction of sea water with upper mantle ultrabasic rocks during serpentinization (a deep hydrothermal circulation system). High pressure and temperature (>400°C), a reducing environment and the presence of various metal oxides are favorable for the abiogenic synthesis of CH4 and oil hydrocarbons (HC). At the Broken Spur vent field, hydrothermal deposits are forming above axial crust magma chambers due to the interaction of sea water and basalts (an axial hydrothermal circulation system). Abiogenic synthesis of HC also occurs in this situation, but to a considerably lesser extent."

Jan 1, 1999

By M. Muinonen, A. R. Barnes, R. Pandher, M. J. Lavigne

Over the past three years, Ring of Fire chromite ores have been tested extensively at both the bench scale and pilot scale at XPS Consulting and Testwork Services. Following bench scale testwork, two smelting campaigns were completed using a 300 kW DC arc furnace on different chromite deposits from the Ring of Fire. A ChemSheet model was developed to aid in the design and optimization of the recipes, and its predictions were confirmed with both the bench scale and pilot scale tests. A total of 7.5 tonnes of chromite ore was smelted at XPS. The results of the testwork demonstrate excellent reducibility for the ores tested with good reduction kinetics when compared with South African chromites.

Jan 1, 2014

By T. Krumins, L. Zunti, R. Frischmuth

Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals, in high-temperature operations. In a vent application, titanium ignition risk is reduced by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature conditions and therefore titanium ignition risk is dependent on standard operating procedures, and process control interlocks and permissive conditions. It is not uncommon for standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions.

Jan 1, 2014

By Erica J. Wanless, Ghislain Bournival, Seher Ata, Jose Hamilton Tavares

In froth flotation valuable particles are captured by bubbles and transferred to a froth layer where bubbles are in close proximity. Bubble coalescence frequently occurs in flotation, especially in the froth layer. The coalescence of two bubbles causes a release of energy, which may expel particles from the bubble surface. A series of experiments were carried out to determine the effect of bubble interfacial properties on the detachment of particles upon the coalescence of capillary-held bubbles of 2 mm in size. The interfacial properties of the bubbles were changed by the addition of low molecular weight alcohols, namely 1-pentanol or methyl isobutyl carbinol (MIBC). Using esterified glass particles (? = 43 °) with a 10 % and 90 % cumulative passing diameter of 47.2 and 92.5 µm, respectively, as model particles, it was found a certain concentration of frother, different for each additive, is needed in order to observe a reduction in the detachment of particles. In the presence of frother, the detachment was evaluated at approximately 65 % which was a considerable reduction in the detachment compared with the value of approximately 85 % found in the absence of frother. Frother molecules changed the properties of the airwater interface. Upon the coalescence of two bubbles, the release of energy caused the merged bubble to oscillate; effectively resulting in the detachment of particles. The addition of frothing agents augmented the elasticity of the bubbles, which appeared to be related to the detachment of particles. Whereas frothing agents are generally used to prevent bubble coalescence and stabilise the froth phase, only transient stability is imparted. The results suggested that an additional role of frothers in flotation is to decrease the detachment of particles from bubble surfaces. The type and concentration of frother can be strategically selected to improve metallurgical recovery as an economic incentive.

Jan 1, 2016

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

In the last 30 years numerous mining plants have been developed in North America but only a handful of these have required freezing the area where the shaft was sunk. The most recent mine shaft to be sunk using this technique is located on an island off the coast of Louisiana. The project required the input and skills of numerous people in several companies, including the owner, engineers and contractors. The Cote Blanche installation is one of several mines in the area which extract salt from a dome which extends under the Gulf of Mexico. The geology of this area is, however, markedly different from others in the region because there is approximately 460 ft of water logged soil above the salt dome. Because it is not possible to sink a shaft in ground that is this soft, the overburden where the shaft is located must be frozen before excavation can take place. The Cote Blanche mine is a producing facility which was built in 1958 by the Carey Salt Company. The original facility included a 14 ft diameter production shaft and a 7 ft-8 in diameter service/ventilation/escape shaft. This system was installed by The Cementation Company. In 1996 the owner decided to improve both the mine ventilation and production hoisting system by installing a third shaft. This shaft would be designed to extract 650 tons per hour from a depth of 1600 ft and provide 500,000 cfm of ventilation to the mine at a maxium design pressure of 4 in WG. These parameters resulted in a requirement for a 16 ft finished inside diameter concrete lined shaft and a headframe designed as a pressure bulkhead. Because the mine would operate from one level only, the most efficient hoisting system for the application was determined to be a ground mounted koepe running on rope guides. With these criteria fixed Cote Blanche embarked on a program which would see construction start in June 1998 with the first salt produced in February 2001 at a cost of $US18M. The major players in the design and construction were G.L. Tiley & Associates Ltd., BLM Bharti Engineering, Freezewall Inc., Phillips Mining, Geotechnical and Grouting Inc., Don Hart Consulting and Dynatec International.

May 1, 2002

By F. Parada L

Two copper concentrate with medium and high enargite content were leached in a 3 L autoclave reactor under conditions based on the CESL process. Copper, arsenic, sulfur and iron were checked in all the experiments and antimony, zinc and molybdenum were evaluated in selected tests. The 98% of the obtained copper extraction is agree with others authors, but the behavior of arsenic, iron an sulfur have some differences. The solid residue was characterized by chemical analysis, DRX and QEMSCAN®. Finally a comparative analysis with neutral roasting as an option for the treatment of this concentrate is done.

Jan 1, 2014

By Yuwang Wang, Yanggeng Tan, Kezhang Qin, Zengqian Hou

Abstract- The large Derni Cu-Co (-Zn) deposit in Qinghai Province exhibits unusual geological features, and its genesis is controversial. Based on previous research and detailed field investigations, petrographic studies of the host volcanic rocks, isotope and trace element geochemistry of the sulfide ore, and comparison with typical ore deposits, this deposit is a VHMS (submarine volcanichosted massive sulfide deposit) type. This argues against previous interpretations of a magmatic or a hydrothermal replacement origin. Systematic rock, mineral and geochemical studies of the host serpentinites of the ore district indicate that the protoliths of several types of serpentinites that are widespread in the ore district are mainly ultramafic volcanic rocks. The mineralization formed within an ultramafic volcanic breccia, or between the breccia and its overlying Mg-rich carbonate rocks and volcanic sedimentary rocks. The ore-forming components were derived mainly from ultramafic rocks and partly from mafic rocks. The ultramafic rocks are MgO-rich, CaO-poor with a high MgO/FeO ratio, and the mafic rocks are rich in Na2O and poor in K2O. The chemical composition of the ultramafic rocks is similar to that of volcanic peridotite, or komatiite. The volcanic rocks that host the Derni deposit are among the most basic host rocks known for VHMS deposits, and the Derni deposit represents the most basic member in the VHMS deposit spectrum.

Jan 1, 2000

By Edmond Chow

Shovel bucket blast fragmentation analysis is an alternate way to assess blast performance and its effects on downstream mining processes. A camera is installed on the boom of cable shovels, and the stick of hydraulic shovels. Images are captured automatically as the shovel digs, and are processed to acquire rock size information. The automatic data acquisition makes this method safe to use with minimal manual labour. It also allows for a large set of sample data to be captured from both the surface and the interior of a bench face. The system has been deployed in several mines to provide an objective assessment of blasting performance. Images are captured from their cable or hydraulic shovels. The images are grouped into sets based on the shovel location and time to match the fragmentation to specific blasts. Blast fragmentation reports are created for each blast after reviewing the results. Measuring blast fragmentation from the shovel bucket proves to be an effective alternative for blast performance assessment with unique advantages. The blast fragmentation information has been valuable to the mines, and the mines have begun adopting it into their operations.

May 1, 2011

By R. Scheepers

"Mineral deposits and prospects of the Pan African Saldanian orogenic belt in the southwestern Cape Province South Africa, are reviewed. Despite the entire absence of operating base or precious metal mines in the area, this study has established at least four metal associations that offer enticing exploration potential.The poly-phase deformed, low-grade metamorphosed volcano-sedimentary Malmesbury Group constitutes a complex, poorly understood supracrustal sequence that has been loosely subdivided into the Tygerberg, Swartland and Boland tectono-stratigraphic terranes by northwesterly trending fault zones. Syn- and post-tectonic granitoids of the Cape Granite Suite selectively intruded these terranes. Early S-types preferred the Tygerberg terrane whereas the later I-types dominate the remaining areas. Anorogenic A-type granites, however, occur in all three domains. Known metallization is directly or indirectly related to the intrusives, yet syngenetic deposits are conspicuously absent from the supracrustals. Four metal associations have been identified.• Cassiterite-wolframite (± Au, Cu, Mo, Fe-sulfides) in quartz and quartz/aplite veins hosted by tourmalinized and locally greissenized S-type granite. Similar exo-granitic veins occur in proximal metamorphites.• Juxtaposed disseminated, stockwork, breccia and vein style Cu-Mo-Fe-(Au)-sulfide mineralization hosted by mafic to intermediate intrusives of high K calc-alkaline, I-type affinity. • Cu-Mo-Au-sulfides hosted by hydraulic breccia pipes, stocks and veins occurring in anorogenic A-type alkali feldspar granites and amphibole quartz syenites.• Scheelite with minor Cu-Mo-sulfides and Au-associated with endo- and exo-skarns spatially related to I-type monzogranite, granite and alkali feldspar granite.The first three associations occur along the Yzerfontein-Helderberg-Zone, a 180 km lineament in the Tygerberg terrane, a zone exploited by syn-, late- and post-tectonic intrusives and their related mineralization. The fourth association is typical of the Boland terrane. The spatial and temporal relationships between the various metal associations is interpreted as the result of sequential intrusion of relative early high level S-type, followed by intermediate level I-type and finally anorogenic A-type granitoids during the evolution of a contracting continental margin arc and its irmer arc. This plate tectonic setting suggests subduction in an easterly direction underneath the Kalahari craton. The spatial configuration of the various terranes at the present erosional levels is the result of rifting and significant differential vertical displacement following cessation of subduction, a terminal tectonic event possibly synchronous with intrusion of the A-type granitoids.Near surface preserved roof zones and cupolas of both S- and I-type granitoids in the Tygerberg and Boland terranes, respectively, render these areas extremely prospective for Sn, W, Mo and Au mineralization. The presence of intermediate to mafic volcanics, a diversity of calcareous lithotypes and favorable plate tectonic setting of the Malmesbury Group suggest potential for the thus far elusive VMS, MVT and Sedex base metal and minor precious metal deposits."

Jan 1, 1994

By Stephen Williams

This paper examines manning best practice in the Australian mining industry. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 15 open pit and 37 underground studies in Australia. The data was collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2008. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. Finally, the paper considers perspectives on best practice with regard to manning in the Australian mining industry and the limitations in application of this type of analysis in a global context.

May 1, 2009