Search Documents

By D. E. M. Plaumann

"The wet grinding of asbestos has attracted the attention of engineers for many years as a means of improving fibre liberation from the ore. Today, added impetus for wet grinding has resulted from a need to minimize worker exposure to asbestos dust in conventional dry mills using air, as well as a need to provide a cleaner, technically superior fibre for use by product manufacturers. However, high viscosities of asbestos slurries create transport and grinding difficulties which have been a factor impeding use of a wet grinding process.Laboratory evaluation of reagents to reduce viscosities of asbestos slurries found that one reagent, XFS-4272.00, reduced the viscosity of a 35% (by weight) slurry by 75%. The impact of XFS-4272.00 on actual grinding parameters were evaluated using a pilot plant rod mill. Slurries containing 78% solids and XFS-4272.00 were successfully milled and asbestos fibres from that milling compared favourably in liberation and relative surface area to asbestos fibres obtained from milling a 4% slurry without additives. IntroductionAlthough the use of asbestos has been declining over the last few years, the large deposits of chrysotile in eastern Canada (Quebec in particular) remain very important. Asbestos production in Canada stands ninth in volume for mineral production with over 740 000 tonnes produced in 1985. Of this quantity, 722000 tonnes were exported with a value of $446 million. Canada is second in world production of asbestos behind the U.S.S.R. The milling of asbestos ore has been done primarily by a series of steps involving crushing, dry-grinding and aspiration using large quantities of air to release the fibres. Contrast this process to those practiced in the purification of virtually every other mineral. Ores other than asbestos are crushed and milled using an aqueous slurry in rod, ball or pebble mills. The finely ground mineral, still as a slurry, undergoes beneficiation by froth flotation, heavy media separation, hydrocyclones or any of the other aqueous techniques currently employed in mineral processing.One of the driving forces behind the use of air instead of water as a means of separating asbestos is the nature of the aqueous asbestos slurry. While most slurries of minerals contain as much as 80070 solids and can still be pumped and transported, asbestos slurries become highly viscous with as little as 10070 solids. These high viscosities reduce the pumpability of the slurry and create severe handling problems. Mills become prohibitively large and uneconomical due to having to handle slurries containing only 10% rock and 90% water.Health-related issues have affected the use of asbestos in many countries. In Canada, the asbestos-producing provinces have introduced stricter occupational legislation to improve safety in the workplace. This primarily means strict control minimizing release of air-borne asbestos fibres . Quebec and Ontario have set limitations of airborne asbestos at 2 (2) and 1(3) fibre per cubic centimetre of air. With present milling technology, maintaining these low levels in the workplace requires constant vigilance."

Jan 1, 1988

Thermal barrier coating (TBC) systems provide thermal insulation to high temperature for aero¬propulsion. A fracture mechanical model developed earlier for multilayer systems is applied on TBC to realize superior performance by enhancement of fracture resistance. Functionally gradient materials (FGM) solution concept is the basis of approach followed here. A few realistic FGM TBCs are considered in the analysis in addition to a conventional TBC as the base case and a hypothetical worst case with YSZ-YSZ interface. Parameters like number, composition and thickness of graded layers and elastic modulus are considered for the analysis and quantitative improvement of fracture resistance of TBCs. The analysis is confined to deep crack with crack size to width ratio as 0.5.

Jan 1, 2010

By R. Druffel, P. Wittke-Gattermann, M. Wittke

"The two tubes of tunnel Hirschhagen along the highway A44 in Germany, underpass the federal road B7, a railway line and the valley of the river Losse close to the city of Hessisch Lichtenau. The ground in the area consists of Triassic sand- and siltstones (""Buntsandstein"") as well as tertiary clays. Prior to tunneling, the groundwater in the area is planned to be lowered by means of a gallery of deep wells. As a basis for the design of this dewatering gallery, two large pumping tests have been carried out. The results of these tests have been evaluated by means of 3D-Finite Element analyses. By means of the large-scale model, the influence of the anisotropy resulting from jointing and bedding and the influence of fault zones in the area have been taken into account, which lead to a thorough basis for the design of the dewatering gallery.INTRODUCTIONThe 4.2 km long Tunnel Hirschhagen of the highway A 44 crosses below the federal road B7, a railway line and the river Losse close to the city of Hessisch-Lichtenau in central Germany. Both tunnel tubes are located in a subrosion depression in which Triassic sandstone and tertiary clay prevail. It is planned to lower the groundwater table in the area of the meadow of the Losse prior to tunnel heading [1]. Groundwater lowering is planned to be achieved by means of a series of large pumping wells. The bottom of the river Losse will be sealed in order to avoid direct inflow of water from the river into the ground (Fig. 1 and 2)."

Jan 1, 2015

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011

By Bertrand Wolfman, William E. Stanley

"This paper reviews the traditional mine accounting systems, including ""custodial accounting"" and unit costing, and then suggests that the use of flexible budgets represents a more suitable method of reporting costs in order to assist the mine manager in improving productivity. Examples of various applications are given to show that the result is a clear reporting structure.Custodial Accounting is Emphasized in Traditional SystemsTraditional mine accounting has been mainly concerned with the accuracy of financial reporting to ""head office"" for the use of the directors and the company's bankers and shareholders. This is often called custodial accounting and it represented the main purpose of accounting when first developed in Europe hundreds of years ago. This important development permitted the establishment of enterprises which were separated from their owners because they could rely on accurate financial reports of management's stewardship.As custodial accounting is fairly broad and historical in nature, it is often not very useful to the mine manager for ongoing monitoring of performance of mining, milling, maintenance, and other support and staff groups. In spite of the considerable investment in accounting staff and computer support, many accounting systems have not been upgraded so that they accurately reflect workplace performance on a weekly or monthly basis.Budgets are Often FixedMany mines today also still emphasize fixed budgets. Thus, the mine plan which is set in the fall of one year is converted to a monthly tonnage and detailed dollar budget for periods of up to sixteen months in the future. The only certainty in this plan is that actual events will differ; timing, mix of mining methods and production volumes will differ on a monthly basis.Unfortunately, the fixed budget has no capability to reflect these operational changes. It is frozen for the full year. The result is that actual results will inevitably be compared to an outdated target."

Jan 1, 1982

By J. Bensabat, B. Figueiredo, A. Niemi, J. Rutqvist, C. F. Tsang

"A hydro-mechanical model was developed to study the interaction between mechanical deformation and fluid flow in the fault zones during CO2 injection and storage at the Heletz site which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The potential reservoir for CO2 storage at the Heletz site consists of three sand layers separated by lowpermeability shale layers. The potential consequences caused by fault reactivation, focusing on the shortterm integrity of CO2 storage, are evaluated. The difference in the results obtained by considering the three-layer as an equivalent layer storage formation is analyzed.INTRODUCTIONLarge-scale storage of CO2 in deep underground reservoirs may cause considerable pore-pressure perturbation as well as flux migration and concern has been raised over whether shear slip displacements may be induced in nearby faults, as a consequence of their reactivation. A state-of-the-art review can be found in Rutqvist (2012), which describes the various possible effects resulting from CO2 injection into a deep sedimentary basin, including those involved in reservoir stress–strain changes, micro-seismicity, caprock sealing performance, and potential fault reactivation. Moreover, several studies have recently shown how CO2 injection may produce seismic events both on major faults (i.e., large faults with large initial shear offset) (Cappa & Rutqvist, 2011a, b, 2012), and on minor faults that might have gone undetected during the site characterization, e.g., faults less than 1 km long and without detected initial offset (Mazzoldi et al., 2012).The present paper is concerned with the Heletz formation which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The Heletz site located at the southern Mediterranean coastal plain of Israel and the structure is an anticline fold with a crest of about 4 km by 2 km. The structure is gently dipping to the east, truncated by a pinch-out line to the west and subdivided into a number of blocks by transversal normal faults with small displacements. The water table is located at 300 m below the land surface. An areal sketch of the site with the elevation of the caprock and the location of the borehole that has been chosen for the CO2 injection experiment is presented in Figure 1."

Jan 1, 2015

By K. N. Subramanian, H. Kanduth

"It is well known that chalcopyrite can be dissociated into simple sulphides by heating with elemental sulphur at about 475°C:CuFeS2 + S -> CuS + FeS2Experimental work was undertaken to determine whether this ""activation"" could be used to advantage in the selective leaching of copper from chalcopyrite concentrate.A method of treating copper concentrate with molten sulphur was developed and the activated product was leached in dilute sulphuric acid using oxygen, ferric iron or manganese dioxide as the oxidant. The object was to obtain a solution suitable for electrowinning with minimal purification, but it was impossible to obtain rapid extraction of copper without simultaneously dissolving a large proportion of iron. This was attributed to the fact that some of the copper was present as a low iron-copper sulphide (idaite) and that the pyrite formed during the ""activation"" step was more easily oxidized than natural pyrite."

Jan 1, 1973

By Chri Langille, Dougal McCreath, Samantha Espley

"In 1993, trials of two innovative applications of liner support involving the replacement of bolts in the ground support system were undertaken at Inco mines. The first trial involved an evaluation of the effect of dynamic loading on mesh-reinforced boltless shotcrete in a sub-level cave mining area on 2400 level at Stobie Mine. The second trial involved an evaluation of the MIROC Mineguard spray-on liner as a replacement for bolts and screen support, or as a replacement for screen support alone, in a topsoil heading of a bulk, VRM (vertical retreat mining) stope on 3240 level at Lower Coleman Mine.In the Stobie Mine trial, an uppers retreat heading was supported using a two-pass system. First, shotcrete was applied 2 inches thick, followed by pinning of mesh screen to the back and walls. A second pass of another 2 inches of shotcrete was then performed. For recovery of the ore zone, a vertical slot was created using a Borepak blind boring machine. The uppers rings were blasted, one or two rings at a time, starting at the slot and retreating out of the heading. During blasting of the production rings, blast monitoring was used to record the ppvs (peak particle velocities). For a series of 5-ring blasts, the maximum ppvs were measured to be 0.4 m/s (16 in./s) with a maximum charge weight per delay of357 kg (800 Ib). Six 5-point convergence measurement stations were set up and after each blast the total rockmass convergence was measured using a tape extensometer. Although a maximum displacement of 100 mm (4 in.) was measured, the shotcrete still managed to provide some support junction. A support damage assessment was also done to try and relate blast vibration to effectiveness of the mesh reinforced shotcrete liner. This trial demonstrated the effect that blasting has, on a support system, and it also demonstrated the necessity of having the mesh reinforcement properly placed within the shotcrete."

Jan 1, 1995

By M. L. Jeremic

"Hydraulic mining consists of coal erosion by powerful jet s of water from hydraulic monitors operated by remote control. The broken coal is crushed and mixed with water and then transported from the face to the surface using gravity whenever possible. This is a simple, safe and productive method. It will easily satisfy North American productivity standards if the structural features and coal properties are favourable for water jet cutting technology (Kaiser Resources Ltd. , hydraulic mine). General ConsiderationIn open-pit mines, placer mining (Fig. I) and hydroelectric construction projects, hydraulic earth moving techniques have been successfully applied. The stripping and transporting of the overburden has been accomplished by means of large monitor jets augmented by slurry pumps and pipes. An extension of this technique has led to the underground extraction of coal and ores. To date, the method has been most successfully used in undergrond coal mining, because the coal can be easily cut and flushed away by water jets, and the rocks of the roof strata can be left behind. Due to this favourable situation, the hydraulic mining definition only relates to the underground coal mines.At present, there are four basic types of hydraulic mining, which can be defined according to the coal breaking technique used in each case. The methods are briefly discussed below:(1) Coal excavation may be carried out by conventional techniques, but the mine is designed and equipped for the hydraulic transport of the mineral from the working place to surface. Under these circumstances, the coal breaking may not be influenced by the water jet, however it may be indirectly involved. For example, pre-loosening of the coal may be done by water infusion-hydraulic fracturing. Water may also be used to flush the broken coal, which has been excavated either by drilling and blasting or by mechanical cutting, into the transport flumes. In other cases, a mechanical loader may load the coal directly into the hydraulic transport system, without using any water for the extraction process. This hydraulic mining concept is primarily used for hard and impermeable coal, such as anthracite."

Jan 1, 1980

By Nick Vagenas

"Loading and transportation are important activities of the mining process. Automation of these activities in underground hard rock mining has been discussed for a long time. This paper deals with the performance evaluation of a prototype automatic Load-Haul-Dump (LHD) vehicle (a 7-ton GHH LF LHD model) operating in Zinkgruvan mine, Sweden. The purpose of the data analysis is to evaluate the operational and maintenance characteristics of the automatic LHD system in the mine. Graphical and numerical methods have been used for the statistical analysis of the data. IntroductionDuring the past years, the idea of integrated automation and tele-operation on Load-Haul-Dump (LHD) machines (Fig. 1) has attracted considerable interest in the Swedish mining industry. This is mainly due to the demand for improvement in the working environment and due to the rapid development of economic and reliable microprocessors for mining vehicles. Several advantages can be foreseen with the application of a Remote-controlled/Automatic LHD (RAL) system in underground mining. Some of them are (1)':• better utilization of working hours;• less interruption in production at shift changes;• better operational control of a fleet of vehicles;• improved safety; and• one operator may be able to operate more than one vehicle simultaneously."

Jan 1, 1993

By Rachel S. Prudhomme, Michael L. Jeremic

"The consolidation of mine backfill by free zing is a concept which has been under study in the mining engineering laboratories at Laurentian University during the past three years. The proposed underground application of freezing involves the artificial freezing of in-situ backfill by means of a refrigerated brine solution which would be circulated through a circuit off freeze pipes. The most interesting findings to date are: (I) The uniaxial compressive strength off frozen fill is considerably higher than that of cemented fill in a ratio of 20:1 (aggregate to cement), and (2) load deformation characteristics of the frozen fill suggest that a higher ice content results in more brittle failure and that samples which have initially failed can still support up 10 one-half the ultimate load without additional failure.Although at this early stage a derailed economic analysis of the procedure has not been possible, a general evaluation of the costs involved suggests that the method could be competitive with the hydraulic placement of cemented backfill. Results obtained from laboratory investigations indicate that the freezing of backfill is a structurally feasible option .IntroductionGround consolidation by freezing is based on the principle of transformation o f water contained in an aggregate-slurry into ice, which act s as a binding agent between the bulk particles, and which results in the transformation of a granular soil into a ""rock -type"" material. The abrasive nature of the particles enhance s the strength o f the ice by providing internal friction. As a result of this internal friction, the chances of plastic flow of the frozen mass when in a loaded condition are reduced(1). T he strength of a frozen aggregate is al so dependent on the grain shape of the aggregate particles which may or may not promote particle interlocking(2) and on the temperature since, below the freezing point of the water/aggregate mixture, the strength of the frozen mass increase s with decreasing temperatures.In the shaft sinking industry, artificial freezing of loose , unconsolidated soils has been in practice for several decades. Shafts for Saskatchewan 's potash industry have been sun k to depths of 3000 feet by employing artificial freezing to stabilize the Blairmore Formation(3). The common procedure for freezing ground for shaft sinking is summarized as follows(4,5): I) 150 mm diameter bore holes spaced on 1.5 m centres are drilled in a circular pattern with a radius of 1.5 m outside the periphery of the proposed shaft."

Jan 1, 1985

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By S. Shairp

Copper is an impurity as well as a necessary reagent in the processing of zinc sulfide concentrate at Hudson Bay Mining & Smelting Co., Limited's (HBMS) zinc pressure leach plant. Copper is present in the zinc concentrate as chalcopyrite, which consumes reagents necessary for zinc leaching. A small percentage of copper precipitates in the autoclaves, discharge lines, and flash tanks, requiring maintenance of the equipment and disposal of the solids. Copper also precipitates in the neutralization stages and is removed to low levels in a specific copper removal stage of purification. Yet some copper, as copper sulfate, is required, along with potassium antimony tartrate, in the final purification stage to improve cobalt removal from the zinc sulfate solution prior to electrowinning. The behaviour of copper experienced at HBMS's zinc pressure leach plant is discussed.

Jan 1, 2008

By V. G. Minenko, A. L. Samusev

For efficient leaching of gold from sulfide ores and the oxidation of sulfides into sulfates, it is necessary to introduce a substantial amount of oxidant - atomic oxygen, hydrogen peroxide, ozone, potassium or sodium hypochlorite. In this paper, hypochlorite electrochemical treatment is proposed as an effective method of intensification of refractory ore leaching. The objective of the study is to increase the gold recovery from refractory ores with the application of chlorinated solutions that are modified by chemical or electrochemical treatment. The advantages of the use of the modified chlorinated solutions instead of cyanide for gold-sulfide leaching are considered to be the following: a high concentration of the oxidizing agent (hypochlorite ions) in solution helps to achieve a high speed of gold dissolution in the form of chloride complexes; the possibility to produce hydrochloric acid solutions that may be used for the recovering gold by electrolysis; the possibility of the processing of carbonaceous, arsenic-bearing and others kinds of refractory gold ores. The mechanism of the interaction of the modified chlorine solutions with gold-bearing sulfides (pyrite and arsenopyrite) was investigated. The efficiency of the application of chemical and electrochemical leaching method was proved. The main factor that limits the rate of gold dissolution is a high concentration of sulfate ions (SO4 2-) formed in the solution by the oxidation of sulfide minerals. The optimal parameters of chemical and electrochemical leaching method and effective ways to remove sulfate ions were determined. The method helps to increase the level of the gold recovery up to 87% from refractory ores. The intensification of leaching by chemical and electrochemical treatment opens up opportunities for the creation of modern efficient and environmentally-friendly technologies that may be applied for gold extraction from refractory gold ores.

Jan 1, 2016

By V. C. Wittchen, T. R. Yu, J. E. Croxall

"The consolidated rockfill at Kidd Creek Mines is a weakly cemented, minus 15 cm aggregate which posed problems for conventional drill/blast drifting methods. Consequently, lateral access to mineable ore adjacent to backfilled areas was gained by drifting around the fill in shattered rock.In mid-1987, Kidd Creek Mines began to investigate means of mechanically excavating drifts in backfill . The results of this investigation led to a trial program using a Dosco MK-2A Roadheader to excavate the required drifts in backfill.The roadheader was tested at Kidd Creek Mines from July to November 1988, in 28-735 X /C to be used as the top access for drilling and blasting 32-74/ ST. During this period, the roadheader excavated 54 m of a 4.3 m by 3. 7 m arched drift in backfill. Cutting rates over the period averaged 0.8 m/cutting hour as projected with a daily high of 2.0 m/cutting hour.Wood-lagged 2-piece steel arches on 1.2 m centres were chosen as ground support for the trial. Shotcrete will be tested in a roadheader drive for its potential to improve productivity by replacing the steel arches.The trial program included evaluations of point-attack picks, two sizes of cutter motor, 20 MPa (3000 psi) water-assisted cutting, cuttings-removal systems, and environmental control devices."

Jan 1, 1990

By I. Pérez-Rey, J. Arzúa, L. R. Alejano

"The decrease in strength with increasing rock specimen size is usually associated to the increase in the number of defects inside the specimens at small scale (centimeters) but also to the role of the rock mass structure at the rock mass scale (meters to decimeters).This matter of concern was particularly focused when determining the size of pillars in underground mines. Some formulae regarding strength of pillars have been proposed but they usually consider only the size and shape of the pillars and the strength of the intact rock. The structure tends to be overlooked or hidden behind the scale, but it is probably very relevant. For standard tunnel design, the approach by Hoek and Brown (1997), taking the structure into account in terms of the GSI, is commonly used. However, this approach does not specifically consider the size of the tunnel. Thus, a size larger than the so-called representative elementary volume is implicitly contemplated.The authors have recently performed a lab study on the effect of the structure in the strength, deformability and post-failure characteristics of granite at lab scale (NX size) extended here. This experimental program included intact and artificially jointed rock specimens. Obtained results permit to observe the changes in strength, deformability and post-failure behavior of this “small scale rock masses”, associating the role of the structure to the observed complete stress-strain response of the specimen, which can improve our understanding of the actual complete mechanical response of rock masses."

Jan 1, 2015

By Zhang. L.

Ordered intermetallic PtSb had been synthesized by arc-melted and then sintering treatment. The electro-oxidation of formic acid on PtSb was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results are compared to those at a polycrystalline platinum electrode surface. It was found that PtSb intermetallic was catalytically more active than pure platinum according to the onset potential and current density. XRD and XPS technologies had been used to investigate the crystal structure and electron effect. We think formic acid decomposition on PtSb favors the reactive intermediate route and is not very much affected by the CO intermediate as compared to Pt.

Jan 1, 2005

By B. N. Church, A. R. Pettipas

"The second vertical derivative method of processing aeromagnetic data from low level helicopter surveys yields results correiatable with the known geology and may be utilized to indicate possible targets for future exploration in the Silver Queen and Equity Silver mines areas, near Houston in central British Columbia . The principal zones of alteration associated with mineralization, known from detailed mapping, are further delineated and extended in a way not possible by a cursory examination of the original magnetic data.IntroductionThe second derivative method of processing aeromagnetic data is a long established procedure used to enhance the short wavelength content of the magnetic fields. Some recent exam pies of the use of the second derivative technique have been published by Chandler (p. 385), Sun Yunsheng et al. (p. 424) and Yarger (p. 223) in Hinze, 1985. According to theory, the ""second vertical derivative"" is closely related to the rate of curvature of magnetic (or gravity) fields and is particularly useful in resolving and sharpening local anomalies. The contours on second derivative maps may coincide with important features such as lithological boundaries, faults and mineralized zones.In the Houston area, central British Columbia, aeromagnetic data supplied by local mining companies provide a ready base for analyses. Examples are data sets for the Silver Queen and Equity Silver mines centred 35 km and 34 km south and southeast, respectively, from Houston (Fig. 1), (Cochrane, 1970 and Church, 1985)."

Jan 1, 1990

By Marc Lavigne

"The Lac Knife graphite deposit was estimated, as part of a feasibility study, using a geostatistical ore reserve estimation method: ordinary kriging. Based on the geology and its interpretation, the results of a variogram study, and the statistical parameters of the grade distribution of the core samples and the composites through the mineralization, the deposit was divided into three separate zones (west, centre and east), and each of these zones was then analyzed and kriged independently.The geological ore reserve estimation results of ordinary kriging are compared to the results of a conventional method (sections) used previously. The two methods gave almost similar reserve figures. The conventional method provided a +2% estimation for tonnage and + 10% for grade because it ignored the spatial relation between sections and samples, and ordinary kriging gave a more accurate longitudinal definition of the deposit.Finally, the paper concludes with the advantages of proceeding with ordinary kriging, namely: higher flexibility (change of cut-off grade), better deposit resolution and enhanced selectivity for the design of the open pit.IntroductionWithin the context of a complete feasibility study for the Société d' Exploration Minière Mazarin Inc., specialists of the Mines and Geology Division of Roche Ltd., Consulting Group, defined a modelling method appropriate to the graphite deposit of the Lac Knife property near Fennont. Many patterns were considered. Based on the geology of this deposit, the planned mining method, the statistical parameters of grade distribution and the variogram study, the process of reserve estimation retained was to use the ordinary kriging in a selective way. It was required because the geometry of the deposit is such that it was unthinkable to apply ordinary kriging without restrictions.This paper gives a detailed explanation of the observations and interrogations which led to the choice of this ore reserve estimation method, and the calculation procedure itself."

Jan 1, 1991

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011