Search Documents

By A. Otsuki

"This paper discusses the primary collector adsorption onto a sulphide mineral in mixed collector systems to understand its adsorption mechanism. UV-vis measurements were performed to identify the primary collector concentration adsorbed on pyrite, and the adsorption kinetics under different conditions were compared to distinguish their difference between single and mixed collector systems. Small amount of secondary collector addition prior to the primary collector addition significantly improved the adsorption kinetics of primary one. The result was explained by the combination of two previously proposed mechanisms (i.e., different adsorption site mechanism and multi-layer product mechanism). This study showed UV-vis measurement as an effective tool to study mixed collector adsorption behaviour.INTRODUCTIONCollectors are surfactants composed of heteropolar molecules with a non-polar and a polar group (Lotter & Bradshaw, 2010). In a froth flotation process, the function of collector is to improve the hydrophobicity of target minerals and selectively float them with the aid of gas bubbles. Because of the chemical or physical attraction between the polar group and the mineral surfaces sites, collector molecules adsorb on the particle surface with the non-polar group assigned towards the bulk solution (i.e., water), thus the mineral particle surface becomes hydrophobic (Wills & Napier-Munn, 2006).Thiol collectors are major collectors widely used in sulphide mineral flotation. Potassium amyl xanthate (PAX), dithiocarbamate (DTC), dithiophosphate (DTP), mecaptobenzothiazole (MBT) are some common thiol collectors. Previous studies reported that some mixed collectors systems enhanced the flotation performance (e.g., Bradshaw, 1997; Bradshaw et al., 1998; Rao & Forssberg, 1997). Thiol collector mixtures are often used in the flotation of sulphide ores, and discussed with the synergistic benefits (Bradshaw et al., 1998) which include lowering the total collector dosage requirements, improving the sulphide recovery and the rate of flotation as well as the improving the froth characteristics. The current paper mainly considered the mixture between two thiol collectors (PAX and DTC, considered as a weaker and selective collector, and stronger and less selective collector, respectively (Bradshaw, 1997)) to further understand their adsorption mechanism that should assist in improving the flotation performance of refractory gold ore."

Jan 1, 2016

By W. Yang, R. Rajasingam, B. Tadesse, K. Mohanarangam

Copper electrowinning is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. Acid mist is produced by these oxygen bubbles bursting at the electrolyte free surface. It is an undesired by-product of the Electrowinning process which unchecked could result in mist generation higher than the recommended time-weight-average exposure limit. Various approaches to alleviate the problem have been adopted by companies, all with varying degrees of success. All of these have been attempts to treat the symptom acid mist rather than the inherent problem, often proving expensive and, in some cases, ineffectual. In this paper, a new method was developed for acid mist quantification based on ‘total acid mist’ capture above the EW cell under well controlled conditions. With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables including current density, flow rate, temperature, etc. independently and their effect on bubble size, bubble velocity, gas hold-up as well as acid mist generation and its droplet size. Results show that total acid mist capture increases with an increase in current density but remains more or less constant between 300–500 A m-2. Total acid mist also shows an increase with increasing electrolyte temperature. These findings are substantiated with the aid of bubble size and gas hold-up measurements with the transparent EW cell.

Jan 1, 2019

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By S. Avalos, J. M. Ortiz, W. Kracht

Semi-autogenous grinding mills are intensive energy consumers. Current models base their energy consumption inference on operational variables and feeding ore characterization. While they provide adequate design guidelines, they are not suitable for real-time energy forecasting dealing with gaps in operational dataset and up/downstream process bottlenecks. This work explores the capability of Gated Recurrent Units to learn the semi-autogenous grinding mill consumption behaviour. Gated Recurrent Units are trained to forecast different time-support consumptions under a time-series operational dataset. The results show high performance on small supports (30 minutes) to capture local variability and long-trends while larger time supports (8 hours) can only capture time-trends but not local variability. The proposed technique seems promising for further research and implementation on real mine cases since the input variables are low-cost and easy to obtain. INTRODUCTION Current changes in the Chilean energy matrix (Román-Collado, Ordoñez, & Mundaca, 2018), from fossil fuels to renewable energies, have impacted different industries and particularly the mining sector. Solar energy incorporation into greenfield/brownfield projects will help reducing costs and will lead to rethink foundational paradigms (production and processing strategies) (Pamparana et al., 2017). Also, integration of new space-time predicting tools together with automated real-time updating models are some of the main challenges in the geometallurgical framework (Ortiz et al., 2015; van den Boogaart & Tolosana-Delgado, 2018). Those contexts encourage and demand the development of tools capable of predicting the energy consumed by mining systems, being comminution the greatest energy consumer with an average close to 50% of the entire mine consumption (Cochilco, 2013). In comminution, the semi-autogenous grinding mill (SAG) represents the largest energy consumer (~10 nominal each SAG). Theoretical and empirical energy consumption models (Jnr & Morrell, 1995; Morrell, 2004; Silva & Casali, 2015) base their inferences mainly on feed/product size distributions, SAG sizing, bearing pressure, feed hardness, water addition and grinding charge level, and commonly assume steady-state and work isolated from up and downstream processes. While those techniques provide adequate design guidelines, they are not suitable to predict hourly, daily or even weekly energy consumptions on interconnected comminution circuits where upstream/downstream bottlenecks lead SAGs to operate below designed regimes. Forecasting energy consumption is required by short-term energy management, medium and long-term planning energy consumption, designing the nominal capacity of renewable energy sources, among other. Also, when models are input-sensitive and some of those input measurements are expensive and/or time consuming, model robustness suffers when real-time predictions are required.

Jan 1, 2019

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By Mustafa Kumral

Monte ? Carlo simulation is often used to assess the risks associated with uncertain variables in mining operations. The success of Monte-Carlo simulations depends upon reproducing the dependencies among variables to some extent. However, some variables may exhibit different dependency patterns. In these cases, classical techniques for dependency quantification cannot capture dependencies. As an alternative, the copulas allow modeling nonlinear dependencies. Furthermore, any choice of marginal distributions can be used. Especially, for the data, which is sensitive to extreme case such as financial crisis, the copulas arise as a means to reproduce the correlations among variables. In this paper, the copulas are introduced to mining practitioners using Monte-Carlo simulations for risk assessment. Then, a case study is given to show the superiority of the copulas over classical techniques using ModelRisk Software. In conclusion, it was observed that the copulas enhance the quality of Monte-Carlo simulations by capturing variable dependencies.

Aug 1, 2013

By David Deglon, Martin Harris, Mehdi Safari

"This study investigates the effect of energy/power input on the flotation of a platinum ore in a pilot-scale oscillating grid flotation cell. Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Secondary rougher feed and primary cleaner tail streams were floated in a pilot-scale oscillating grid flotation cell at power inputs from 0 to 2.5 W/kg, using 0.50 and 1.50 mm bubbles. From this study one may conclude that the effect of energy/power input on the flotation rate is strongly dependent on the particle and bubble size. Flotation rates generally increase with increasing particle size and decreasing bubble size. Increasing energy input generally leads to an increase in the flotation rate for finer particles and an optimum flotation rate for intermediate & coarse particles. Optimum conditions for intermediate/coarse platinum ore particles are using small bubbles at low energy inputs, or large bubbles at higher energy inputs. These results suggest that higher energy inputs are generally beneficial for the flotation of platinum ores as these consist predominantly of finer particles (-75 µm) and most industrial flotation applications operate with larger bubbles (1.0-2.0 mm).INTRODUCTIONThere is a considerable body of experimental and theoretical evidence to suggest that energy/power input plays an important role in flotation kinetics, particularly in the finer particle sizes where flotation efficiency is poor (Deglon, 2005). A number of excellent studies into the effect of energy on flotation kinetics have been carried out in impeller stirred cells (Ahmed and Jameson, 1985; Deglon, 2002; Pyke et al., 2003; Newell and Grano, 2006). Investigations using this type of cell have a number of limitations. The impeller influences particle suspension, bubble break-up and agitation in the cell. In addition, turbulence is highly inhomogeneous and anisotropic, with power intensities near the impeller orders of magnitude higher than those found elsewhere in the cell (Deglon, 1998; Koh and Schwarz, 2003; Schubert, 1999, 2008). These limitations have resulted in the development of novel cells for the investigation of energy input."

Jan 1, 2016

By A. L. Irwin

THE disposal of tailing or waste material, which is generally a very large proportion of the ore treated, is a major problem in the location and operation of any concentrating enterprise and especially so where the life of the operation is expected to continue for many years. Many factors need to be taken into consideration in the selection of a tailing site, chief among which are economical handling of the material, subsequent re-treatment of the tailing, and precaution against stream pollution by waste water. The final location of many mill sites bas been governed largely by the selection of a sui table area for tailing storage. The Sullivan concentrator of the Consolidated Mining and Smelting Company is situated about three miles from the Sullivan mine at Kimberley, B.C., and one of the deciding factors in its location at this distance from the mine was the availability of a suitable area in which tailing could be deposited. In view of the indicated long life of the property, a far-sighted policy bad to be adopted in the matter of tailing storage, for not only would it be necessary to accumulate a huge tonnage of finely ground material, but also reclamation for iron recovery at some future date bad to be considered. Some idea of the extent of the problem may be grasped when it is noted that, by the end of 1938, over 18,000,000 tons of tailing bad been impounded in an area of some 200 acres.

Jan 1, 1939

By G. M. Proudfoot

IN June, 1940, a .Longyear 3420 blast-hole drill rig was purchased by the Hudson Bay Mining and Smelting Company for the purpose of experimental blast-hole drilling. The early work showed that the diamond drill could compete successfully with the Leyners then in use and by January 1st, 1941, the diamond drills were placed on contract. They may be considered to have gone into production at that date. Prior to the introduction of the diamond drill, our bench drilling was clone with Ingersoll-Rand S-70 and S-83 Leyner drills. Holes up to 40 feet were drilled, using coupled 1 1/4-inch round steel. Bits with a gauge of 3 inches were used in starting these holes, with a drop of 1/8-inch gauge for each 2-foot run. The holes normally ended with 1 1/2 or 1 5/8-inch gauge, though bits down to 1 1/8 inches were available for holes longer than normal or for holes drilled in abnormally abrasive ground. This method of drilling was very satisfactory and was a distinct improvement on the three-bench method of drilling used previously (1). During 1937 and 1938, when experienced miners were available, Leyner long-hole drilling was carried on with great efficiency. However, in 1939 and 1940, labour turnover in-creased and experienced long-hole drillers became scarcer. This resulted in a marked decline in the efficiency of the drilling operations, with increased costs and less tonnage drilled per shift. EXPERIMENTAL WORK The initial diamond drilling test work was carried on with a Longyear 3420 air-driven blast-hole drill rig, drilling a 1 3/16-inch hole. Tests indicated that diamond drilling could be successfully adapted to local conditions and that overall costs compared favourably with costs obtained with the Leyner long-hole method. Leyner long holes on stope benches usually bottomed at a larger diameter than the 1 3/16 -inch diamond-drill holes. More powder could therefore be introduced into the Leyner holes than could be placed in the diamond-drill holes. To achieve the same fragmentation, additional footage was required when diamond drilling. Diamond-drill holes of larger diameter were indicated.

Jan 1, 1943

By Jin Li

The tensile properties and microstructure of AZ91 Mg alloy before and after equal channel angular extrusion (ECAE), and the fracture behavior during tensile testing for as-extrusion and ECAE AZ91 were investigated. The alloy was performed ECAE from one to eight passes at 498K. The elongation decreased with the pass number increasing after ECAE. Grains were refined, partial coarse ß-Mg17Al12 phase fell to pieces, fine ß-Mg17Al12 precipitated in the AZ91 Mg alloy after ECAE. During tensile test the a-Mg/ ß-Mg17Al12, a-Mg/Al8Mn5 interface and the grain boundaries in a-Mg matrix acted as the crack initiation sources. The frequency of micro-cracks at the a-Mg/ß-Mg17Al12 interfaces and grain boundaries increased after ECAE, which accelerated the growth and coalescence of the micro-cracks during tensile test and resulted in the decrease of elongation of AZ91 Mg alloy by ECAE.

Jan 1, 2006

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016

By T. Kagawa

Ever-increasing demands for non-ferrous metals owing to population growth and improvements in the standard of living in the world, under the constraint of limited availability of natural resources, would easily make us imagine that more efficient and sustainable developments in mining and smelting activities are required in the near future with due consideration for environmental concerns. In order to realize the efficient and sustainable development of mining and smelting activities and operations, the following issues are indispensable: (1) to investigate the up-to-date pollution control technologies of mine and smelter, (2) to promote those technologies, (3) to develop technologies which are environmentally friendly. This paper discusses the recent technologies for environmental conservation/prevention and their diffusion in the world, and also the key technologies required for the most desirable sustainable development.

Jan 1, 2007

By P. J. Oakley, W. M. Thomas, S. W. Kallee, D. G. Staines

A Friction stir welding (FSW) is now extensively used in aluminium industries for joining and material processing applications. The (FSW) technology has gained increasing interest and importance since its invention at TWI almost 15 years ago. The basic principle, recent applications and the continuing development of the FSW technology are described. The paper will introduce some of the variants of FSW, such as Dual-rotation, Twin-stir(TM), and the Stir-lock(TM) technique.

Jan 1, 2006

By Horace Freeman

Introduction In the aggregate, directly and ?indirectly, the pulp and paper industry ? consumes very large quantities of a variety of minerals, or compounds prepared from minerals. This is especially true in the manufacture of news-print, but fine papers, also, account for some of this consumption, in the processes of loading, coating, and otherwise improving the finish. The more important of the minerals used in the industry in Canada are briefly dealt with in the following pages. The list is by no means exhaustive, however. Thus, barite, lithopone, zinc oxide, zinc sulphide, and titanium oxide are used in small quantities in Canada in filling and coating paper. Up to the present time, however, the quantities of these materials used in the paper industry have not sufficed to encourage their manufacture in Canada. In the case of barite (barium sulphate)-or of witherite (barium carbonate)-it may be said that, should deposits of commercial size be discovered in Canada, the ore would have considerable export value, for use in the paper and other industries. China-Clay (Kaolin) Considerable quantities of china-clay are used for brightening and improving the finish of paper, and there is a growing tendency to use larger amounts of this material in newsprint manufacture. No china-clay suitable for paper manufacture is at present produced in Canada, but samples have been forthcoming recently from a deposit near St. Remi d'Amherst, Labelle county, Que., about thirty miles north of the Ottawa river and approximately midway between Montreal and Ottawa, and plans are under way to conduct large-scale tests with this material. Present sources of supply are the United States, England, and Russia.

Jan 1, 1934

By R. Kong, X. W. Zhang

"High pressure (up to 50 MPa) isotropic compression tests were performed on marble, gneiss and sandstone specimens, of which represents the typical rocks, to investigate isotropic compression deformation characterization at room temperature. Experimental data with respect to volume change in loading and unloading are presented. An apparent volume change inflection point (sensitive stress) was observed at a lower pressure range for porous sandstone, indicating that the elastic-plastic behaviour arising in the isotropic compression stage, but for tight crystalline rock, the sensitive stress is much higher, not probed prior to 50 MPa. The irrecoverable volumetric strain in the unloading can be seen for sandstone as well. The anisotropic deformation was discussed in terms of the axial and radial strain measurement. It was found that essential features of mechanical anisotropy are the irreversible in deformation range. The deformation feature in the isotropic compression tests is a very complex issue due to the factors concerning the stress history, unloading in sampling and in-situ stress. INTRODUCTIONThe isotropic or hydrostatic compression condition that stress is compressive and has the same magnitude for all direction, which is expressed as s1=s2=s3 in principal stress space. A yield locus of soils subjected to the isotropic and anisotropic compression was widely known, for instance Cam Clay model, which forms a closure cap model. However, the similar isotropic compression yield curves for rocks, especially for hard rock, was not established due to the geo-stress in the rock mass is much less than the socalled isotropic yield stress. And hence, the previous experimental studies on the hard rock have been made tend to on the stress-strain-strength relationship (Handin & Hager, 1957; Edmond & Paterson, 1972; Menéndez et al., 1996). Perhaps the yield curves related to an increasing in the hydrostatic pressure is not forced to construct for hard rocks, undoubtedly, the deformation data in this processing is valuable to assess the bulk module (Fabre & Gustkiewicz, 1997), anisotropy (Niandou et al., 1997), field stress (Hakala et al., 2007). Furthermore, many rocks store much elastic volume strain energy link to the hydrostatic pressure exerted, following a deviator stress applying, to drive the unstable brittle fracture for hard rock. Latter was studied to interpret the incentive of rock burst. However, volume change characteristic in the isotropic compression behaviour have been scarcely studied experimentally to our knowledge, less application related to the fracture in hard rock as well. The mechanical behaviour in the isotropic compression of hard rock is notably affected by the original structure anisotropy, stress history and stress condition before sampling, all of which need reasonably assess. It is also a useful understanding to study isotropic compression that elastic and plastic volume change in the isotropic loading and unloading, and the micro crack evolution throughout it."

Jan 1, 2015

By A. C. Gagnon, H. Saroglou

"The focus of this paper is on the analysis of geometrical discontinuity properties for the rock mass located within an open pit mine located in Western Africa. Discontinuity data were collected using various techniques including oriented core logging, borehole televiewer surveys, surface pit wall mapping and photogrammetry. The geological setting was initially studied prior to the data analysis to produce threedimensional ground models of the regional and mine site geology along with block diagrams illustrating predicted fracture patterns. Stereographic and statistical discontinuity data analysis of the geometrical properties of the rock mass was subsequently performed to identify unique structural domains throughout the open pit area. The discontinuity data collected throughout the studied open pit area were primarily discontinuity orientation, frequency and spacing and the investigation focused on the reasons for observed differences between the various data collection techniques. Stereographic analysis was used to assess the preferred geometry of discontinuities filtered by lithology, data collection technique, borehole, discontinuity type and pit wall (footwall or hanging wall). The observed fracture pattern is explained adequately by the geological setting. The need for accurate ground models for the design of open pit slopes is highlighted.INTRODUCTIONThe Tasiast Mine is an open pit operation located in north-western Mauritania, approximately 300 kilometres north of the capital Nouakchott. The Tasiast mine, which is owned and operated by Kinross Gold Corporation (Kinross), began commercial operations in 2008. The Tasiast mine is located in an area characterized by flat desert terrain within the western reaches of the Sahara Desert region. The current mine site includes mill buildings, shop facilities, waste dumps, tailings facilities and two main open pit operations (Piment and West Branch). The West Branch pit is the focus of this paper. The current open pit plan for West Branch indicates a final pit measuring approximately 2.5 km long by 1.4 km wide and 510 m deep."

Jan 1, 2015

By L. I. Kiss, S. Perron, S. Poncsák, A. Perron

Aluminium industry has an increasing interest in the diminution of the energy consumption of the Hall-Heroult process by the reduction of the anode bottom covering with gas. Electrically isolating carbon-dioxide bubbles, produced at the anode, increase the ohmic resistance of the cell. As the gas production rate is determined by the applied current density, anode covering can be decreased only by a faster evacuation of the gas from the inter-electrode space. Among others, the inclination and curvature of the anode bottom promotes the release of the bubbles and thus decreases the mean value of the covering. Indeed, anode, insert in the molten cryolite bath has a square shape with horizontal bottom. However, inhomogeneous anode consumption, electro-erosion, bath circulation and the inclination of the bath-metal interface modify this shape gradually during electrolysis. Anode bottoms become inclined with rounded comers. This concentrates the gas generation to the center zone of the anode. As the bubble layer cannot be observed directly because of the hostile environment and the opacity of the bath, real scale air-water systems are used to study the impact of the anode geometry on the anode covering and the bubble induced flow. However, the physical properties of such a system are different than that we can found in the real cells. A simulator using the Lagrangian description of the bubble layer has been built and presented in earlier papers. This tool was used to investigate the effect of the anode inclination on gas covering and bath velocity, for both C02-cryolite and air-water system. Results obtained for the second system were compared to experimental data .

Jan 1, 2006

By D. K. Sarkar, Ying Huang

"Superhydrophobic thin films were fabricated on aluminum alloy substrates by chemical etching followed by passivation with organic acid molecules; (ii) electrophoretic deposition (EPD) of functionalized ZnO nanoparticles and (iii) electrodeposition of organic-inorganic composite materials. The physical and compositional analyses of the deposited thin films were characterized by SEM, FTIR, XRD as well as contact angle goniometer. The contact angle and surface roughness of the superhydrophobic surfaces prepared by the chemical etching process were found to be 156° and 2.29 µm, (ii) by the EPD process were found to be 155° and 4.54 µm and (iii) by the electrodeposition process were found to be 159° and 7.11 µm, respectively.The corrosion properties were analyzed with both polarization and electrochemical impedance spectroscopy (EIS) in NaCl aqueous solutions. The results demonstrate that the superhydrophobic thin films on aluminum alloy substrates display better anti-corrosion behavior than the as-received aluminum substrate. The comparison of results pertaining to the compositional and corrosion properties of these thin films on aluminum will be discussed in this work.INTRODUCTIONSuperhydrophobicity is defined as a surface property which provides non-wetting characteristics with a water contact angle larger than 150°. It is observed that the creation of certain micro-nanoroughness structures promotes the entrapment of air in the spaces of the rough surface morphology. In addition, lowering the surface energy helps to reduce the affinity of water drops to the surface, thereby weakening the water-surface interaction. Recently, various fabrication methods for superhydrophobic surfaces have been explored (Sarkar, 2010, Huang, 2010, 2011, 2013, 2015a, 2015b), such as the sol-gel process (Brassard, 2011), plasma treatment (Marchand, 2013), chemical vapor deposition (Zheng, 2009), chemical etching (Saleema, 2011), electrodeposition (Ying, 2011) and electrophoretic deposition (EPD; Huang et al., 2015b)."

Jan 1, 2016

By G. R. Guillet

Salt is restricted to five major beds in south western Ontario, totalling as much as 200 m in thickness. These beds are located at depths ranging from 270 m to 750 m below the surface, fringing Lake Huron and the Detroit River from Windsor to Kincardine, and extending inland as far as London. Manitoulin Island, the Bruce Peninsula and the north part of the Niagara Escarpment form the northeastern rim of the Michigan Basin, a major structural depression in which the salt was deposited 400 million years ago when much of North America was covered by the Silurian sea. Salt is mined underground at Windsor and Goderich; it is also brought to surface as brine through deep wells at Windsor, Samia and Goderich. Artificially- created caverns in salt beds are extensively used for storage of liquid hydrocarbons at Windsor and Samia.

Jan 1, 1984

By K. V. Gow, F. A. Jerabek

"THE NOVA SCOTIA TECHNICAL COLLEGE has been granting degrees in mining engineering since 1909. The college was established in 1907 to provide the final two years of the undergraduate program in engineering the earlier years of which are given at several small universities scattered around the Atlantic Provinces. Since the beginning of the program, 251 Bachelor of Engineering degrees have been awarded in mining engineering. Although the average class size has been small, increases in enrolment in the past few years have resulted in Nova Scotia Technical College being the second largest mining department in Canada, based on the number of graduates per year. This year 18 students received B.Eng. degrees, and next year 17 will graduate.In 1968, it was necessary to make a decision on whether or not to abandon, for economic reasons, the program in mining engineering. For several years enrolment had been very low and resignations among the mining engineering staff created a situation in which the program could easily have been dropped. However, it was decided to continue mining engineering, as it was the only such program in the Atlantic Provinces. New staff members with many years of practical experience in the mineral industry, not only in Canada but in the U.S.A., South America, Africa and the U.K., joined our department. At the same time the enrolment in mining engineering began to increase significantly."

Jan 1, 1972