Search Documents

By V. T. Panayotov, M. I. Panayotova

Wastewater from mining and mineral processing activities is often polluted by anion forming metals, such as molybdenum and chromium. Low cost materials, including zeolites, are studied for removing heavy metals from wastewater. It is widely accepted that natural zeolites are not effective in removing metals in anionic form. The paper presents study on use of metal modified natural clinoptilolite to remove Mo (VI) and Cr (VI) ions from model soft wastewater. Modification with Pb, Fe(III), Zn and Ba increases clinoptilolite uptake capacity with respect to Mo(VI) at low pH values of the water subjected to treatment, the efficiency decreasing in the order Pb > Fe(III) > Zn > Ba. Only lead-modified clinoptilolite shows high uptake of Mo(VI) in acidic, neutral and slightly alkaline conditions. Modification with Pb, Ba and Fe(III) increases zeolite uptake capacity with respect to Cr(VI) from neutral water. The effectiveness of Ba-modified zeolite decreases in slightly acidic water. Over 90 % uptake of initially available Cr(VI) is achieved by lead-modified clinoptilolite both under neutral and slightly acidic conditions. Increasing the initial pollutant concentrations increases the removed amount both of Cr(VI) and Mo(VI) for Pb-modified clinoptilolite. The findings could be a basis for using the natural clinoptilolite to remove in consecutive steps: firstly Pb(II) and/or Fe(III) ions and then loaded zeolite to be used for Mo (VI) and/or Cr(VI) removal. The kinetics of Mo(VI) uptake by CL-Ba, CL-Fe(III), CL-Pb, and CL-Zn is best described by the pseudo-first order kinetic equation. The kinetics of Cr(VI) removal by CL-Ba, CL-Fe (II), CL-Fe (III) and CL-Zn is best described by the pseudo-first order kinetic equation. Kinetics of Cr(VI) removal by CL-Pb obeys the equation for the first order irreversible reactions. Finding way to remove anions-pollutants from the mineral processing wastewater will render this industry more environmentally friendly and socially acceptable.

Jan 1, 2016

By A. Gourlie

"This paper describes the performance properties of a new 95 ksi minimum yield strength, oil well casing grade designed specifically to resist hydrogen sulphide stress corrosion cracking, SSCc. The new grade, Soo-95SS, demonstrates NACE Tensile threshold values greater than 90% specified minimum yield strength, SMYS, and NACE Bent Beam values in excess of 12.7 x 1()4 psi. The new Soo-9588 grade also exhibits superior collapse and notch toughness values. IntroductionIn recent years, a trend toward casing grade specialization has resulted in the introduction of numerous proprietary grades designed specifically for particular production environments, In response, Algoma Steel has developed, as part of a "" grade for service"" philosophy, two new 95 ksi minimum yield grades. The two grades are Soo-95, High Collapse (HC), and Sour Service (SS). This paper describes the development of Soo-95 Sour Service.Four main objectives were established:1. Definition of the steelmaking and continuous cast processing practices2. Determination of the acceptable maximum and minimum levels for all chemical elements3. Definition of special processing requirements4. Definition of the physical characteristics and ranges of the product properties.This paper provides a description of the experimental approach, followed by a presentation and discussion of the trial results . Finally, a number of conclusions are given."

Jan 1, 1988

By R. H. Nafziger

A novel process has been developed for preparing directly workable steel ingots from prereduced iron ore pellets by a two-stage process. The pellets are continuously charged into an electric arc furnace, where molten metal is separated from the gangue. The molten metal flows out of this furnace through a hollow nonconsumable graphite electrode immersed in a molten flux in an electroslag furnace. The molten metal solidifies on a continuously withdrawing base plate to form the ingot. A variety of standard carbon and alloy steel ingots . free of porosity , were produced using suitable decarburizers and ferroalloy additions. Some advantages of the two-stage process include: (a) consumable electrode fabrication is eliminated; (b ) no expensive deoxidizers are required; (c ) the uncontaminated electros lap flux can be reused; (d) energy consumption averages 25% less than in a conventional electric arc - electroslag operation ; and (e) the operation is continuous.

Jan 1, 1977

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006

By A. Ashrafi

The electrochemical deposition of polypyrrole coating on different pretreated aluminum-alloy 7075 substrates was carried out using cyclic voltammetry, The pretreatment of specimens consisted of mechanical polishing and/or electrochemical etching, In the latter case, an aqueous solution of phosphoric acid and ethanol was used, The electrodeposition solution was 0,25 M pyrrole and 0,1 M oxalic acid in double-distilled water, The cyclic voltammetry scan rate used was 700mv/s, Morphology of the coatings was examined using scanning electron microscope (SEM), Using the Tafel experiment, corrosion resistance of the coated substrates was investigated in 0.1 M NaC1 solutions, Results obtained revealed that electropolymerization of polypyrrole on 7075 aluminum alloy would increase the resistance against corrosion in 0,1M NaC1 solution, Also it was observed that, compared with mechanical polishing, electroetching pretreatment would be more effective.

Jan 1, 2005

By R. Carter, C. S. Samis

"SummaryThe results of this investigation indicate that the gold in the cyanide tailing of refractory gold cyanides is occluded in fused •particles formed during roasting. This conclusion was reached following microscopic examination of calcines produced at various furnace temperatures with different atmospheres, and a •comparison with calcines produced by decomposing samples of completely sulphated concentrate under conditions such that the maximum particle temperature varied between 6•50°C. and 1,100°C. This comparison showed that the particle temperature during a normal roast may be several hundred degrees higher than the furnace atmosphere, or that the fusion is associated with a low melting (950°C.) eutectic mixture of FeO and FeS.Because of the unavoidable particle fusion during a furnace roast, and because low particle temperatures are essential for gold extraction by cyanidation, aqueous medium oxidation under high oxygen pressures was studied. Gold recovery from calcines produced by this means was over 98 •per cent •compared with a maximum of 80 per cent from furnace calcines.IntroductionMANY arsenical gold ores are called 'refractory' because much ' of the gold cannot be satisfactorily extracted by cyaniding the raw ore or concentrate. Even when such ores are roasted to oxidize .the iron and arsenic and 'release' the gold, often 10 to 25 per cent of the gold present is lost in the cyanide residues."

Jan 1, 1952

By M. Kalin

Tailings deposits are frequently the source of ground water contamination due to the transport of contaminated tailings pore-water. If amendments to tailings covers could be made to facilitate a precipitation reaction and halt or reduce the generation of acid in pyritic tailings, the quality of pore-water quality would be improved which would in turn reduce the production of contaminants. The effects of phosphate wastes, added to base-metal mine tailings in Newfoundland, Canada, were tested. Laboratory and field experiments determined the effects of different mixing ratios of phosphate wastes to tailings volume (1:4, 1:8, 1:12 and 1:20, dry weight) for a total period of 3.2 years. The addition of phosphate at ratios of 1:4 to 1:12 substantially increased the pore water pH, and reduced both acidity and Zn concentrations. These results suggest that addition of phosphate wastes to tailings covers can reduce acidity generation and improve tailings pore-water quality.

Jan 1, 2004

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By Jean-Jacques Bouillon, Michel Jébrak, Stephane Faure

"Le gisement polymétallique (Cu-Zn-Au-Ag) des Mines Selbaie est forme par un réseau de filons encaisses dans une séquence de pyroclastites felsiques du sill on Harricana-Turgeon. Les minéralisations sont encaissées dans le tuf de Selbaie, situe sous une épaisse séquence d'ignimbrites Iitées. Ce gisement se distingue des autres gites archéens par une chronologie atypique des minéralisations: les veines de chalcopyrite, de sphalérite et de galène recoupent un amas exhalatifpyriteux stérile. Un vaste halo d'altération hydrothermale a chlorite et mica blanc est associe à cette minéralisation.La mise en place des veines minéralisées est associée à une phase d'extension NNW-SSE. Le complexe volcanique subit, par la suite, trois phases de déformation. Une compression, orienté N-S, développe une schistosité à peine pénétrative et un réseau de fentes de tension. Une réorientation des contraintes locales selon une direction WNW-ESE conduit au chevauchement de I' écaille d'andésite et de tonalite de Brouillan. Un réseau conjugue de failles normales cassantes est associe au relâchement des contraintes."

Jan 1, 1990

By Mei-Yan Yang, Ltd. Yunnan Yuntong Zinc Co., Yong-Xiang Li, Xing-Zheng Dai, Hong-Liang Wang, Meng-Yang Huang, Peng Zeng, Guo-Feng Li

"The removal of iron asgoethite from the high iron bearing solutions generated in zinc hydrometallurgy using a strong airflow device was investigated. The influence of oxygen flow, copper ion concentration, temperature and reaction time on iron precipitation as goethite was studied. The optimum conditions were: oxygen flow 0.2-0.35m3/h, copper ion concentration 0.25-0.5g/L, temperature 80-90oC, zinc oxide powder neutralizing agent and a reaction time of5to 7hours. Under the optimal conditions, the Fe2+concentration was reduced to 0.025g/L after iron precipitation, and the goethite residue contained 38.7wt.%Fe. The SEM and XRD analyses showed that the iron was present as well formed FeOOH crystals in the iron residue, and the amount of iron sulphate was very low. Production practice shows that, when the average iron concentration in the feed solution was 11.61g/L and 4.08g/L after precipitation, the weight of iron removed was 1,439kg/day. When the average iron concentration in the feed solution was 14.51g/L and 2.73g/L after precipitation, the weight of iron removed was 2,454kg/day. This represents a ~70 percent increase in iron removal.INTRODUCTIONThe objective of iron removal is to produce a small volume of iron residue, and our industrial goethite process meets this requirement. The high Fe(II) solution in our reactor isoxidized/hydrolyzed to precipitate goethite and the precipitate is sent to a pyro metallurgical furnace for final residue treatment. Some literature discusses (DengYong-guiet al., 2008;Meiguang-guiet al., 2001;Zhongzhu-qianet al., 1980) research on iron hydrolysis; one of the reported rate limiting parameters was the low availability of the oxidant when using air and another was the inhomogeneous air distribution. There are two iron hydrolysis-goethite precipitation methods; the Electrolytic Zinc process (EZ) and the Vieille Montagne process (VM) (Lei Xiang, 2006; Xuguo-qiang, 2007;ZhaoYonget al.,2005). The EZ method hydrolyzes the Fe3+directly to FeOOH. The weakness of the EZ process is the low recovery rate of the associated minor metals. The VM method reduces the iron to the ferrous state and then oxidizes the Fe(II)to Fe(III),with simultaneous hydrolysis/precipitation of the Fe(III) as FeOOH. Before iron hydrolysis, the minor metals, such as indium, could be selectively precipitated, because Fe(II)requires a high pH for hydrolysis. So the VM method has a high recovery rate for the minor metals. There levant goethite precipitation reaction is:"

Jan 1, 2016

By N. Shi, T. G. Joseph

ABSTRACT Before any large plant is moved onto an oil sands dominated surface, particularly those surfaces encountered in-pit, it is imperative that the ground be evaluated for bearing capacity. A 2230 tonne mobile in-pit hopper/crusher facility designed for operation in the Canadian oil sands was modeled. This evaluation focused on track and outrigger pad versus ground interactions as the key performance indicators of appropriate ground performance below the unit in both operating and repositioning propel modes. A study of cyclic oil sand behaviour was also inferred from laboratory cyclic plate load data as an extension of the simulation model indications.

Jan 1, 2013

By J. S. Roper

"IntroductionSNOW LAKE is situated in northern Manitoba at latitude 54° 55 and longitude 100°, 400 miles northwesterly of Winnipeg, 80 miles northeast of The Pas, 80 miles east of Flin Flon. A 38-mile road from Wekusko, on the Hudson's Bay railway, serves the community.The mine is located in and close to the southern edge of the Precambrian Shield in typical low-relief muskeg and lake country.The Howe Sound Exploration Company, Limited optioned the property from Nor Acme Gold Mines, Limited, after preliminary diamond drilling had outlined two orebodies of low-grade arsenical gold ore.Following the examination and study of geological data and of 50,000 feet of diamond-drill core, and metallurgical tests made during 1942 to 1945, a decision was made to develop the mine and build a 2 ,000-ton mill concurrently. This development has been described by G. C. Lipsey in a paper entitled The Development of a Mining Operation from Diamond-Drill Data which was published in the August. 1952, issue of Mining Engineering.Geological Features of the OrebodiesThe orebodies at Snow Lake occur in volcanic rocks of acid to basic composition and, to a lesser extent, in intrusive hornblendite. The hornblendite is a massive, uniform, .coarse-textured rock except in the immediate vicinity of the ore zone, where it becomes sheared and carbonatized. The acid volcanics have been converted to quartz-garnet-biotite gneiss, and the basic volcanics to amphibolite gneiss. Orebodies have been formed by the replacement of all three rock types."

Jan 1, 1955

By Z. Zhang, X. -G. Chen, F. Breton, A. Arici

"The microstructure of Al-10Si-0.3Mg-0.5Mn alloy with 0.27% Zr and 0.19% V addition was quantitatively analysed and compared to the base material. The addition of Zr and V in the AlSi10Mg alloy exhibit a beneficial effect on the Si modification, resulting in the reduction of the size of eutectic Si particles on both as-cast and T6 conditions. The quantitative image analysis results show that the Zr and V addition and T6 treatment can reduce the size of the intermetallic phases. In addition, the presence of Zr and V is favour to the partial dissolution of the intermetallic phases during the T6 treatment. Different heat treatment procedures were tested to optimize treatment parameters. The mechanical properties of the alloys were evaluated using hardness measurements and tensile tests. The results show that the addition of Zr and V can remarkably improve the mechanical properties on as-cast and T6-treated conditions. The correlation between the microstructure and mechanical properties of the alloys is discussed.INTRODUCTION Al-Si-Mg foundry alloys have been widely used in automotive and aerospace industries due to their high strength-to-weight ratio, heat-treatable capability and excellent castability. The alloying elements such as Cu, Mn, Fe are traditionally added into Al-Si-Mg alloys to improve their mechanical properties (Mohamed, Samuel, Samuel & Doty, 2009). In recent years, the attention has been paid to the effect of the transition elements such as Zr, V, Ti, etc, as minor alloying additives, on the properties of aluminum alloys (Elhadari, Patel, Chen, & Kasprzak, 2011; Kasprzak, Amirkhiz & Niewczas, 2014; Shaha, Czerwinski, Kasprzak, Friedman & Chen, 2015; Shaha, Czerwinski, Kasprzak & Chen, 2014; Mahmudi, Sepehrband, Ghasemi & 2006; Meng, Cui, Zhao & Zuo, 2013). Kasprzak et al., (2014) and Shaha et al., (2015) reported that additions of Zr, V, and Ti in Al-Si-Cu-Mg cast alloys can improve the alloy mechanical properties at high temperature by forming stable intermetallics and precipitates on as-cast and heat treatment conditions. On the other hand, the mechanical properties of near-eutectic and eutectic Al–Si cast alloys depend not only on the chemical composition but also, even more importantly, on microstructural features such as the morphology and size of eutectic silicon and intermetallic particles, which are present on both as-cast and heat treatment conditions (Mohamed et al., 2009). However, there is rather limited information on the effect of Zr and V on the microstructure features and mechanical properties of near-eutectic Al-Si-Mg cast alloys."

Jan 1, 2018

By I. Soosaiprakasam

This work investigated inhibition performance of copper carbonate (CuCO3), which is less toxic than conventional heavy-metal corrosion inhibitors in amine treating plants, The investigation was experimentally carried out in a bench-scale electrochemical corrosion cell under an atmospheric pressure, The inhibition performance of CuCO3 in an aqueous solution of monoethanolamine (MEA) was examined under a wide range of operating conditions and reported as a function of process parameters including inhibitor concentration, temperature and solution velocity, The results show that CuCO3 functions as an anodic inhibitor. The addition of CuCO3 decreases corrosion rate of carbon steel but might induce pitting corrosion/

Jan 1, 2005

By J. U. MacEwan

Introduction The equilibrium between copper, zinc, and chlorine may be considered as the simultaneous equilibrium of the two separate chemical reactions of formation of the stable chlorides of copper and zinc at the temperature of the reaction i.e., l440°K. (1,167°C., 2,133°?F.)§ [Zn(g) +Ciz(g) ZnCl2z(g). ... (1) ] [2Cu(l)+Cbi'g) Cu2Cl2(l 1 ....... (21 ] Subtracting, [Zn(g) +Cu2(Clz(l i ZnClz(g) +2Cu!l) ... . (3) ] If this reaction is carried out with a copper-zinc alloy at some constant temperature above the melting point of brass, and at a total pressure of one atmosphere, the equilibrium concentrations obtained will depend on the free energy decrease .of the reaction as written in (3) and on the activities of the various components in. the reaction mixture. If the equilibrium is examined from the point of view of the phase rule, it is a three-component system, and if it exists in two phases (liquid and gas) it will have three degrees of freedom. If the restrictions of constant temperature and pressure are imposed, the degrees of freedom are reduced to one. This means that, in a two-phase system under these conditions, each different alloy phase will be associated with a gas phase of constant composition.

Jan 1, 1951

By T S. Cochrane

A variety of practical tests have been tried in the mining industry to determine the support properties of mine roof bolts. Such tests include torsion wrench readings, hammer blow tests and the use of plates with built-in tension indicators. This paper gives some details of pull tests with a hydraulic jack, as carried out in coal mines of western Canada. M A~Y criteria exist for establishing the efficiency of roof bolting, and the one adopted de-pends on the nature of the problem and on the individual leanings of the investigators. Consequently, sufficient studies have not been made from a common viewpoint or under similar geological and techno-logical conditions to compare these methods of evaluation. However, regardless of whether certain tests provide sufficient factual data to form a basis for theoretical research on bolting or not, many of these tests can and do provide a positive means of judging the suitability of chosen roof bolting techniques and equipment under definite geological conditions.

Jan 1, 1963

By M. Fainerman-Melnikova

The use of strong base ion exchange resins for the extraction of uranium was pioneered in the 1950?s. Ion exchange technology is applicable to dilute leach solutions such as those obtained from in-situ, heap leaching or in-plant processing of low grade ores. A further advantage of ion exchange processes is that fluidised bed technology allows for treatment of solutions with a relatively high concentration of suspended solids and resin-in-pulp technology can treat leach slurries. However, the extraction of uranium with strong base resins is severely affected by the presence of chloride ions in solution. In areas where high quality water is not readily available, the use of saline water as process water would extend the potential application for ion exchange in uranium processing. Our research program has studied the effectiveness of a wide range of commercially available ion exchangers in uranium extraction from saline solutions. In the present work, we examine the impact of salinity (ranging from chloride concentrations found in groundwater to those present in sea water), on the uranium extraction with weak base anionic resins (WBA). The effect of pH and the presence of the competing impurities are also discussed.

Aug 1, 2010

By Stewart W. Daniel

"Increasing labour costs, the trend to larger mills, the processing of lower grade ores and a diminishing sup-ply of well-trained and experienced mill operators contribute to the necessity of automating a grinding circuit. With sophisticated process control techniques, supervision of the mill line is reduced to an occasional inspection by the shift supervisor. Process operating decisions and/or adjustments are quickly and accurately performed by the electronic devices to be described. When the variables in the grinding circuit are stabilized using the sensors and controllers as discussed, the over-all grinding circuit is maintained at its optimum grinding load level, with ample protection against under-and overloading."

Jan 1, 1967

By J. R. Dinn

On the afternoon of Saturday, June 23rd last; there was an unusual occurrence at the surface plant of the Dominion Coal Company's Caledorria mine, Glace Bay, which operates on the Phalen seam, here lying at a depth of 170 feet from the surface. On that day, the writer, who was attending a business conference in the General Office about a mile distant from the Colliery, received a telephone call to the effect that there was a strong odour of gasoline or kerosene in the wash-house and lamp-house of the Colliery, and that the attendants in both the wash-house and the lamp-house had become ill and had had to be sent home. Instructions were given at once to cut off the electric current, and to close all doors to prevent access to the building. When the writer arrived at the plant and questioned the workmen, he was led to the belief that the gasoline tank in the lamp-house (used in connection with flame safety lamps) had leaked and that the gas, having volatilized, had displaced sufficient oxygen to cause the trouble. Emphasis was being placed on the kerosene, or, as some said, the gasoline, odour. In the lamp-house, there is a small shuttered window which opens on a corridor. Here the workmen receive their lamps from the lamp attendant. An examiner, with a flame safety-lamp, proceeded to test the atmosphere within the building by passing his lamp through the open window, since, if the trouble was due to volatilized gasoline, a gas cap would be shown on the flame of the safety-lamp. After holding the lamp for a few seconds inside of the window, he withdrew it and remarked, "There's no gas cap" . Almost immediately the lamp fell from his hand and he dropped unconscious to the floor of the corridor. The writer, who was standing beside him, felt no ill effects and removed him at once from the corridor. Steps were immediately taken to revive him ( artificial respiration) , and in about ten minutes he became conscious and was breathing naturally. In making the examination, his head was not inside the window, but in line with the frame of it. It was apparent that some gas more deadly than the hydrocarbons from gasoline was present.

Jan 1, 1934

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Constrained groove pressing (CGP), as a severe plastic deformation (SPD) technique, is one of the applicable methods for sheet metal forming capable of producing ultra-fine grained materials (UFGMs). In CGP, processing and die design parameters can significantly affect the deformation response of sheet metal specimen. Having said this, in the present research the effects of die design variables and processing parameters (i.e. shear angle and friction) on the deformation behaviour of an Al-Mg-Si Alloy are studied thoroughly. Finite element analysis (FEA), was used to evaluate the effectiveness of mentioned parameters on the deformation homogeneity, strain distribution and pressing load variations. Also, mechanical properties of the deformed sample in term of micro-hardness was analyzed. It is observed that with increasing the shear angle, effective stress, strain and pressing load are enhanced. Moreover, by increasing the coefficient of friction, pressing load enhances. The color coded micro-hardness measurement showed a good agreement with the strain distribution obtained from FEA (higher hardness for the zones associated with higher shear plastic strain values).INTRODUCTIONWork hardening results in enhanced mechanical properties upon cycles of deformation (Hosford & Caddell, 2007). However, the formability of the processed products are affected by work hardening reducing the possibility of processing in subsequent deformation cycles. Therefore, many industrial processes cannot be performed on sheet metals to produce products with desired mechanical and physical properties (Valiev, Islamgaliev, & Alexandrov, 2000). Severe plastic deformation (SPD) is an effective grain refining technique which can impose large plastic strains through cold working on a metallic specimen (Bisadi, Rastgou, Payganeh, Zeynali, & Ghahremani, 2010). SPD techniques are mainly categorized into three types; sheet, bulk and tube forming. Among SPD sheet forming methods, Constrained Groove Pressing (CGP) (Shin, Park, Kim, & Park, 2002), Accumulative Roll Bonding (ARB) (Saito, Tsuji, Utsunomiya, Sakai, & Hong, 1998) and Repetitive Corrugation and Straightening (RCS) (Zhu, Lowe, Jiang, & Huang, 2001) possess potential applications in manufacturing industries."

Jan 1, 2016