Search Documents

By J. G. George

A brief review of the silver industry is presented to set the stage for the analysis of the distribution of silver production by source from various types of mines in Canada and of the changing relationship between the total output of silver and the total output of base metals. The decline in the average grade of the Canadian mines is also discussed and a trend for the future is proposed. The report then examines in broader aspects the world primary silver production and concludes, in the section on outlook, that the effective supply in primary silver will grow at a rate significantly lower than the growth rate expected for base metals. A cumulative deficit of some 900 million ounces is projected for the period 1975-1980 and a further deficit of some 1,100 million ounces if projected for the 1980-to-1985 period.

Jan 1, 1977

By P. A. Riveros, J. Binvignat, V. M. McNamara, D. Koren

The recovery of cyanide from a gold mill solution containing high levels of copper (400 mg/L to 900 mg/L) using the AVR process was evaluated. It was determined that acidification to pH 2 to 3 provides a suitable balance between HCN generation, copper precipitation and acid consumption. A short pilot plant campaign showed that ~75% of the feed WAD cyanide was recovered while the remainder precipitated along with copper upon acidification. The acid consumption averaged 3.5 g H2SO4 per litre of solution. The copper precipitate, consisting mostly of CuCN and CuSCN, was readily separated from the solution by gravity. The volatilization of HCN in countercurrent packed columns averaged 98.7% efficiency. Reabsorption of HCN was practically 100% in NaOH solutions and slightly lower in a lime slurry. Basic volatilizer design parameters applicable to a large-scale operation were determined, including the Henry’s Law constant and the mass transfer coefficient of HCN gas.

Jan 1, 1998

By George P. Demopoulos, Nima Parsi Benehkohal, Marianna Uceda

Lithium-ion batteries (LIBs) find wide range of applications from portable electronics to electric cars and stationary storage or renewable energy. LIB electrode fabrication is done through mixing the active material (Li-ion host) with carbon (conductive component) and polyvinylidene fluoride (PVDF), which acts as a binder. These components are dissolved in N-methyl-2-pyrrolidone (NMP) to form a paste which is then doctor bladed onto the aluminum current collector. NMP is a toxic chemical and the overall fabrication process remains costly. Efforts are made of eliminating NMP by (1) replacing the binder and (2) using a new fabrication method. Of particular interest among these new methods is electrophoretic deposition (EPD). Via the application of DC potential, particles in suspension can be electrophoretically deposited on different conductive substrates in a relatively fast rate rendering EPD feasible for industrial application. A key aspect for successful application of EPD is the formulation of a stable suspension. Within the McGill HydroMET group, we explore the potential of EPD in fabricating LIB electrodes having demonstrated its effectiveness in the case of P25 nanotitania/carbon anodes. The performance of EPD fabricated TiO2/C electrodes is compared to standard PVDF-based electrodes and shown to have comparable charge capacity. This method is now being extended to other electrode materials. In this paper an introduction to the EPD method will be made and subsequently its use in fabricating LIB electrodes will be described. The performance of the fabricated batteries is evaluated via galvanostatic charging/discharging and cycling tests.

Jan 1, 2016

By James G. Lyons

All machines vibrate and make noise. An increase signals impending trouble. Vibration and noise analysis allows the condition of the machine to be determined without costly interruption in service for disassembly and physical inspection.

Jan 1, 1977

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980

By G. W. Poling

This paper evaluates current environmental protection legislation, guidelines and criteria, focusing mainly on the land and water disposal of mill tailings. Effluent criteria and regulatory mechanisms are proposed, and submarine tailing disposal is discussed at length. The importance of basing regulations on the best available rationale is stressed.

Jan 1, 1979

By W. Chi, R. Regan, R. A. Washington

"In uranium mines, the purification of underground mine air can be accomplished by the removal of dust particles and radon daughters using filters. Full-scale statistically designed experiments with flow rates up to 10,000 cfm have been conducted at Denison Mines Ltd. on mine air filtration with vermiculite as a filter material. Various filtration bed thicknesses were chosen, with different face velocities through each bed thickness. Results on total dust, respirable dust and radon daughter collection efficiencies were analysed statistically. It is shown that these collection efficiencies are directly related to the filter bed thickness. However, the different face velocities seem to affect only the collection of radon daughters. Optimum collection efficiencies for a clean bed of about 30% were found for respirable dust and radon daughters, and about 41>% for total dust, using an 8-in.-thick bed and a face velocity of 500 fpm. Dust build-up on the filter bed during operation led to an increase in collection efficiency, reaching 40 to 60% after two weeks."

Jan 1, 1973

By K. E. Barnes

"The “Jameson Cell” flotation cell was developed at Mount Isa Mines in the late 1980’s to address deficiencies in our flotation column installations. Early base metal installations had a variable record. The test work and trials showed they made an improvement metallurgically when operated correctly, but performance of the early installations was hindered by a range of operational and maintenance issues. The installations needed to be more robust, and we needed a better understanding of how to successfully integrate the cells into the plant flow sheet.During the 1990’s, Jameson Cells had great success in coal fines flotation and organic removal in SXEW applications, and became the standard in these applications in Australia. These installations improved the cell design and materials of construction and the cell flow sheet design, to make it low wear with self-regulating control, producing good performance with little operator input.These improvements have enabled a fresh look at the use of Jameson Cells in base metals. Recent new installations have shown significant benefits in “hybrid” circuits, that combine the best features of both Jameson Cells and conventional flotation cells, achieving better overall circuit performance in a smaller footprint than either technology could do by itself.Case studies of successful base metal applications are discussed, using size-by-size mineralogical performance to explain the improved circuit performance. The new methods of flow sheet test work design are also described."

Jan 1, 2006

By W. K. Coughlan

The Wabana deposit of Dosco Industries Limited is situated on the east coast of Newfoundland, at Bell Island in Conception Bay. It is a Clinton-type iron-formation of Lower Ordovician age. Five separate beds have been recognized, with others noted locally. Economic production has been obtained from the Lower, Middle and Upper beds, which are second, third and fifth in sequence, al-though at present only the Lower Bed is worked. The potential area of occurrence is about 70 square miles. It i;; bounded by major faults to the north, east and west and truncated by erosion at the south, where rocks of the de-posit crop out on the north side of the island. The iron is contained in oolitic hematite and chamosite, with minor siderite. As the deposit is submarine, conventional exploration methods are not applicable and much interpretation and projection from mined areas is necessary to guide exploration and development. With the interpretation of information from existing mined ores, it is possible, using a minimum of diamond drilling in advance of working faces, to maintain adequate ore reserves.

Jan 1, 1966

By D. Sprott, P. A. Kirsch, J. Harris, D. Cliff

This paper details the work of RISKGATE, the largest Australian Coal Association Research Program (ACARP) occupational health and safety initiative to date. The program is an interactive online risk management system developed to maximize health and safety performance in the coal mining industry by implementing continuous improvement in managing major unwanted events. The comprehensive knowledge base covers tires, collisions, fires, isolation, strata control underground, ground control open cut, explosions, explosives, manual tasks, and slips/trips/falls. All major Australian coal mining companies contributed topic experts to this broad industry initiative: nine coal mining companies, more than 80 experts, and more than 400 days of individual time for knowledge-capture workshops.

Jan 1, 2014

By Catherine T. Ziten

Introduction ?Environmental assessments required for permitting ?Focus on ammonia produced through mine construction & blasting ?Water quality guidelines: federal, provincial, IGO ?Reported values are typically estimates from other projects ?Predictive modelling of ammonia aimed to assist planning

May 1, 2009

By P. R. Geoffoy, T. Koulomzine

"The discovery of the Mogador deposit concealed by 100 feet of overburden was the result of combined application of geological reasoning, ground geophysical surveys, studies of glacial float and extensive diamond drilling. The ground was acquired because it lay on the projected intersection of the Manville and Laflamme River faults. Systematic ground prospecting led to discovery of mineralized floats. A first unsuccessful exploration campaign lasted several years and consisted of 137 drill holes.In 1951 the boulder nests were reexamined and an associat'on of the mineralized float with boulders of a granodiorite, unknown in outcrops of the district, was established. Consequently, ground magnetic surveys were extended and re-interpreted, and a large anomaly interpreted as corresponding to a batholith was outlined. The existence of the batholith was immediately confirmed by drilling and the Mogador deposit discovered in third hole of new drilling programme in a zone of fractured volcanics paralleling southern contact of batholith.The Mogador deposit is a complex replacement of silicified volcanics by pyrite, pyrrhotite, sphalerite, chalcopyrite and galena carrying values in silver and gold. A total of 1,230,000 tons has been indicated, most of it now classified as fully developed proven ore."

Jan 1, 1960

By F. D. Forgeron

"ONE OF THE FIRST DOCUMENTED APPLICATIONS of soil geochemistry in the Canadian Shield was that carried out by Chisholm in the Kenora district in 1949. This survey proved successful in outlining sulphide-associated gold veins utilizing cold-extractable metals. Since then, mining companies, government agencies - both provincial and federal - and universities have conducted soil investigations. Some of the results are documented in publications, others are on open file in provincial and federal mines departments and, unfortunately, many other investigations with both successful and unsuccessful results are buried in company files or have been discarded. This paper deals with soils within the scope of chemical studies of overburden in the Canadian Shield. The subject is a broad one and some definition is required. The soil investigations discussed herein are those aimed at the testing of specific targets more or less in the source area. This definition distinguishes soil investigations from other overburden studies which commonly monitor metal accumulations at some substantial distance from the metal source. Naturally this distinction is relative, because in many instances there is overlap."

Jan 1, 1971

By Hidenori Hatta, Takero Watanabe, Hideo Yoshida

"The effect of the quenching rate on age hardening in an Al-6.0mass%Zn-0.75mass%Mg alloy sheet was investigated. The quenching rates and aging conditions were as follows: water quenching (WQ) or furnace cooling (FC) followed by pre-aging at 20°C,then artificial aging at 120, 160 or 200°Cwere performed. The peak strength of the FC and the WQ are very similarat120°C aging. It is important high strength was obtained even at the extremely slow quenching rate. On the other hand, the strength of the WQ significantly decreased compared to the FCat200°C aging. GP(I) zones were formed during the pre-aging at 20°C even if the cooling rate was very slow like the FC, and were transformed into the GP(II) ones at 70°C or higher and then into the ?’ phase. However, these zones were dissolved by reversion during heating to 200°C. Thus the strength of the WQ decreased. On the other hand, it is considered that an unknown cluster or GP zone with a thermal stability formed during the FC was not dissolved up to 200°C and was transformed into the ?’ phase. Therefore, a higher strength was obtained in the FC for the200°Caging.INTRODUCTIONAl-Zn-Mg alloys are widely available in commercial production because these alloy have lower quench sensitivity and can be produced by air cooling (AC). Heat treatable aluminum alloys are usually produced by water quenching (WQ) to increase their strength because a high cooling rate inhibits the precipitation of the stable phase during cooling and increases supersaturated solute atoms. However, Baba(1967)reported the strength of an Al-6%Zn-1.8%Mg(mass%) alloy without additional elements quenched by very slow cooling (15°C/min) was 96% of that quenched by WQ. Furthermore,the age hardening at room temperature (RT) occurs after annealing at 410°C followed by furnace cooling (FC, 0.5ºC/min or less)in these alloys. Therefore, the process of annealing at 410 to 430°C for 120 min followed by AC, and reheating at 230°C for 240 min, then cooling is recommended in the specifications (Japan Aluminum Association, 2011). Matsuda and Yoshida(1996)also recommended annealing at 300°C for Al-Zn-Mg alloy extruded products to inhibit age hardening at RT by precipitating the solute atoms and decreasing them in the matrix. It has been considered that the higher the content of excess quenched-in vacancy becomes by WQ, the higher aging rate at RT is obtained. Therefore,it is theoretically and commercially important to clarify the reason why the age hardening occurs relatively quickly in almost no excess quenched-in vacancies such as the FC, and why the same strength as the WQ can be obtained in the FC"

Jan 1, 2018

By James Pirie

"The major Archean gold deposits in the Red Lake greenstone belt, which have produced over 374 million grams of gold since 1930, occur near the top of the lower komatiitic to tholeiitic mafic to ultramafic metavolcanic sequence. The upper calc-alkalic mafic to felsic rocks form three discrete and separate ediftces overlymg this lower sequence.The gold deposits are classified according to their stratigraphic or lithologic associations into:1) mafic-volcanic-hosted deposits;2) felsic-intrusive-hosted deposits; and3) stratabound deposits.Group 1 and to a lesser extent Group 2 deposits occur within zones of alteration several square kilometres in extent. The nature of this pervasive alteration can be characterized by comparison of petrochemical data from the altered rocks and their fresher equivalents some distance away. The altered rocks have substantial addition of SiO2> CO2, K2O, As and Sb and subtraction of Na20, CaO, MgO and total Fe. Cr, Ni, Co and Zr appear to have been relatively immobile. Hydrothermal alteration and gold deposition probably accompanied early fumarolic activity and continued during subsequent deformation the metavolcanic sequence, with gold eventually being mobtltzed and concentrated into major vein structures to form the present orebodies. The smaller Group 2 deposits formed by emplacement of felsic intrusions into already altered, anomalously gold-bearing mafic metavolcanics, with the heat from the intrusions setting up parasitic hydrothermal systems which mobilized the gold and deposited it along with minor sulphides in fractures in the cooling intrusions."

Jan 1, 1982

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By J. Gotor, C. Frias, E. Delgado

The Iberian Pyrite Belt (IPB) is one of the world's largest reserves of primary sulphides containing base metals (Cu, Zn, Pb), precious metals and some special metals such as indium. Estimated resources are over 1,500 million tonnes of volcanogenic massive sulphide ores. From 1980´s Europe lives the decline in its mines mainly motivated by the low price of the metals. One aspect that contributed equally to this was the ecological disaster produced by the discharge of more than seven million tonnes from the tailings dam of Boliden-Apirsa (Aznalcollar) in 1998. Today the situation is different; the companies present in the IPB have given evidence that it is possible to reconcile mining projects and care on the environment, and the regional authorities are opening a public tender to re-start Aznalcollar mine. A new challenging era has been started at this Spanish/Portuguese mining area. This paper presents the results and preliminary economics of a project devoted to IPB primary sulphides processing through different technology approach, e.g. conventional selective flotation against bulk flotation or mixed metals flotation combined with hydrometallurgical processing.

Jan 1, 2014

By M. J. Collins

"Autoclaves were first used in the metallurgical industry in 1893 to recover alumina from bauxite. In the 1940s and 1950s, several high temperature and pressure processes were invented in the laboratory of Professor Frank Forward at The University of British Columbia, in parallel with advances in equipment and processes by the Chemical Construction Corporation. Sherritt Gordon Mines Limited enlisted these groups to help develop the nickel sulfide ammonia leach process that was commercialized in 1954. Autoclave processes that have since been commercialized include high-pressure acid leaching of laterites, zinc pressure leaching, and pressure oxidation of refractory gold feedstocks. RÉSUMÉ En 1893, l’industrie métallurgique est la première à utiliser les autoclaves pour l’extraction de l’alumine dans la bauxite. Dans les années 1940 et 1950, plusieurs procédés à haute température et à haute pression sont inventés dans le laboratoire du Pr Frank Forward de l’université de la Colombie-Britannique (UBC) ; parallèlement, la Chemical Construction Corporation fait de grands progrès en matière d’équipement et de procédés. Sherritt Gordon Mines Limited fait appel à ces groupes pour qu’ils aident la société à développer le procédé de lixiviation du sulfure de nickel dans de l’ammoniaque, commercialisé en 1954. Les procédés de lixiviation en autoclave commercialisés depuis incluent notamment la lixiviation acide à haute pression de latérites, la lixiviation sous pression du zinc et l’oxydation sous pression des matières premières de l’or réfractaire.INTRODUCTION Autoclaves are chemical reactors that are built to contain processes taking place at elevated pressure. They are used in metallurgical refineries throughout the world to take advantage of the increased reaction kinetics and different reaction products that can be obtained in aqueous systems above the boiling temperature at atmospheric pressure. The word autoclave comes from the French “auto” and the Latin “clavis” and literally means self-locking—that is, the core distinguishing feature of an autoclave is that it includes a means for pressure regulation (e.g., a pressure relief valve). Denis Papin (Figure 1a), one of the inventors of the steam engine, was the first to make use of a safety valve to control steam pressure. He is credited with inventing the autoclave in 1679. Papin’s “digester” (Figure 1b) was a type of pressure cooker that was originally used to liquefy bones. Most commercial autoclaves are horizontal, multicompartment vessels with mechanical agitation, as shown in Figure 2a; however, the steam-agitated Pachuca vessels used to leach laterite ore in Moa, Cuba (Figure 2b), are also classified as autoclaves according to the self-locking definition provided above."

Jan 1, 2018

By R. H. Pemberton

"THE Mattagami district of Quebec has, during the past few years, experienced intense exploration by virtually every mining company operating in Canada. As a result of this activity, a number of well-mineralized zinc-copper bearing bodies have been found, some of which will almost certainly go into production. Much of the area has undergone what is now termed ""Saturation Prospecting"" or intense and detailed geological and geophysical surveying, followed by the drilling of nearly all possible bets. Considering only the airborne geophysical surveying, some blocks of ground have been flown by virtually every geophysical instrument which has to date been installed in an aircraft. A list of these different geophysical instruments would include: l. Fluxgate-type total field magnetometers 2. Vertical field magnetometer ,3. Nuclear-precession magnetometers 4. Single-frequency out-of-phase electromagnetometers 5. Dual-frequency out-of-phase electromagnetometers 6. Horizontal component measuring electromagnetometers 7. In-phase and out-of-phase electromagnetometers8. Dip-angle measuring electromagnetometers."

Jan 1, 1961

By Edwin G. Sharp, Frank S. Gaunce, George M. Freeman, Denis J. Kemp, Eric Dulson, Paul Salmon, Ernest R. Hamilton, Carl E. Parden

"THE ECSTALL ZINC PLANT was built for the treatment of the Kidd Creek zinc sulphide concentrates. Construction proceeded throughout 1970-71, with operations beginning in April 1972. The two concentrate types treated differ principally in minor impurity and precious metal contents. Processing flexibility was required to allow efficient recovery of the by-products, especially cadmium, copper and silver. The conversion of the zinc sulphide concentrates to end products follows a sequence of operations that are common to most electrolytic zinc plants and typical of the ""Tainton- Jephson"" flowsheet.1. Roasting in air at an elevated temperature to convert the metal sulphides to soluble metal oxides (calcine) and sulphur dioxide. The sulphur dioxide is converted to sulphuric acid in a contad plant and shipped by train to market.2. Leaching of the calcine in spent electrolyte to effect extraction and recovery of zinc as zinc sulphate solution, leaving an insoluble residue.3. Purification of the clarified zinc sulphate solution by cementation with metallic zinc dust to remove impurities detrimental to the electro-deposition of zinc or detrimental to product purity. The solids from cementation are the starting materials for secondary metal recovery.4. Electrolysis of the purified zinc sulphate solution to reduce the zinc to the metallic state while coincidentally regenerating the sulphuric acid for recycle to the leaching step."

Jan 1, 1974