Search Documents

By Eric Konigsmann, Doug Spence, Scott Jones

"The Williams Gold Mine is located in the Hemlo camp of Northwestern Ontario and is one of Canada’s largest gold producers with annual gold production of 400,000 ounces. The operation is owned and operated as a 50:50 joint venture between Teck Cominco Limited and Barrick Gold Corporation.In July 2002, the decision was made to introduce paste backfill produced from mill tailings as the primary backfilling method in the mine and to decommission the existing cemented rock fill system. This required a fast track design to be completed for both a surface paste backfill plant and an underground paste distribution system followed by an intensive construction phase through the fall and winter of 2002/2003. The paste system was commissioned on schedule in late April 2003 and was in full production within 4 weeks of the initial start up. Overall, the project duration was only 42 weeks from initial project release to commissioning and it was completed $2 million under the budget of $14 million.This paper presents an overview of the lab testwork and process flowsheet design, process control methodology and describes the construction and commissioning phases of the project. Preliminary paste plant performance and operating cost data is also presented.IntroductionThe Williams Gold Mine is located in Northwestern Ontario adjacent to the Trans Canada Highway in the Hemlo Gold Camp as shown in figure 1. The mine currently produces approximately 400,000 ounces of gold annually and is owned and operated as a 50:50 joint venture between Teck Cominco and Barrick.The deposit was discovered as part of the Hemlo gold discovery in 1981 which led to the development of three mining operations within a 2 kilometre radius. The neighboring operations are the Golden Giant Mine, currently owned and operated by Newmont Gold, and the David Bell Mine, currently owned and operated by the same joint venture which is running Williams. David Bell ore is blended and milled in the Williams concentrator."

Jan 1, 2004

By S. Chung

Mining in highly stressed ground conditions has been an increasing challenge at the Brunswick mine. Over the past 30 years, two large regional pillars were established on the 1000 m Level to support the ground for safe extraction of the surrounding ore. The South Regional Pillar contains about 5 Mt of ore and the North Regional Pillar has about 3 Mt of ore. In the fall of 2000, mining activities were suspended following a series of ground movements around the South Regional Pillar along weak geological structures. After extensive geotechnical investigations, a decision was made to carry out a mass de-stress blast in the West Ore Zone (WOZ) to cut the principal stress across an area of 135 m along strike and 86 m high. At the end of July 2001, the WOZ mass blast was successfully initiated. Following this success, the mine decided to take a similar approach to de-stressing the North Regional Pillar (NRP). The final mass blast was taken in early February 2003. Advanced blasting technologies, including state-of-the-art electronic detonators and blast simulation, played an important role in achieving the successful blasts. The high precision of delay timing and long delay duration of the electronic detonators ensured accurate and reliable initiations of over 800 blastholes in the WOZ mass blast. Orica’s DMC_Blast (Distinct Motion Code) simulation code was used to study different blasting blocks for the desired timing in the initiation sequence. This paper describes the process of applying electronic detonators in complex blasts, and discusses how blast simulation results were interpreted to guide engineering design of the mass blasts.

Jan 1, 2005

By Dominic Fragomeni

"The mineral processing industry has had a long history of innovation that is recognized but not often celebrated. These include significant advances in mineral measurement, testing, comminution, mineral separation and process control technologies that have transformed mineral assemblages into ore.This presentation presents some of the major mineral processing innovations and the impact they have had on our industry. As we look to the future, it is critical that we innovate and change. We will explore some examples of the next developments and how they can be catalyzed in the face of risk management, lower metal price cycles, resource constraints, inertia and the challenge of short term value delivery."

Jan 1, 2017

By R. W. Mei, R. A. Strombom, D. J. Moore

"Heat-shrinkable cable accessories are solving problems in the mining industry. This paper describes a range of products used by the industry, including low-voltage splices, high-voltage splices to 8.7 k V, cable repair sleeves, mining cable terminations used on system voltages up to 25 kV and motor connection kits up to 8 k V. Technical procedures and designs are illustrated.IntroductionThe development of high-performance heat-shrinkable materials slightly over 20 years ago proved to be one of the major technological breakthroughs in power cable accessories. Heat-shrinkable products were introduced initially for use as low-volt age cable accessories in the aircraft and electronics industry. A program of continuous development and product introduction now enables the manufacturer to offer a broad range of products for mining, industrial and utility electrical systems.With the advent of atomic energy, an important discovery was made-exposure of some plastic materials to high-energy electrons can cause the permanent crosslinking, or intermolecular joining, of adjacent molecules. Once the material has been crosslinked, it will not melt or flow at any temperature.The unique properties of heat-shrinkable products also result from the exposure of special thermoplastic formulations to high-energy electrons. Because of crosslinking, these products have perfect elastic memory. The heat-shrinkable products are supplied in expanded condition. When heated, they will shrink and tightly cover the object over which they have been placed. 'The functional and operating demands of mine cable accessories exceeded the classic electronic applications of heat shrinkable materials. These demands required a very sophisticated program to develop materials and adhesive systems that could endure the operational environment associated with the mining industry,Ease of assembly, low installed cost and operational reliability are among the main reasons for the acceptance of heat-shrinkable mine cable accessories in electrically powered mines. For over a decade, these systems have been demonstrating proven performance."

Jan 1, 1980

By T. G. Joseph

Mines must manage variability from within their operations as well as those imposed upon them by external forces. This paper provides a framework to manage both internal and external variability through the review and adjustment of the mine plan where applicable to minimize lost production and maintain operational safety.

Nov 1, 2011

By L. K. Walker, G. A. Kosick, P. D. Young

"MillEX is an information management system designed by mineral processors for mineral processors. The system utilizes ""cutting edge"" software technology to gather and store all automatically and manually recorded data from the plant operation and laboratories. This data is delivered to the desk of superintendents, metallurgists, technicians and managers, and permits the user to query, correlate, graph, report and present this data in minutes. In the past this task would have taken days and even weeks of tedious work to complete.MillEX allows the engineer/analyst to quickly develop a very thorough understanding of the complex relationships of process variables and equipment that exist in the plant, and their effect on product quality and quantity. The time and resources that are currently wasted on duplicating data entry will be an effort of the past.This paper describes the structure of MillEX and how it conforms to the needs of mineral processing personnel.INTRODUCTIONPicture a personal computer on your desk which will carry out the following commands:1. Plot a graph over the last six months, using weekly averages, of percent minus 200 mesh material in the primary cyclone overflow.2. Overlay this graph with a graph of concentrate grade versus recovery over the same time period.3. Retrieve a prior month end report, update all operating supplies tables and metallurgical performance with this months data, and embed the graphs created above.4. Edit text and print the current month end report. This is only one example of the type of power MillEX isbringing to the mineral processing industry."

Jan 1, 1992

By Sanjeeva Latchireddi, Travis Orser

"Today’s high capacity semiautogenous grinding (SAG) mills expend vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. The energy efficiency of these high throughput grinding mills can be attributed to the field of breakage and slurry discharge system. The charge motion and breakage of particles inside the mill depends on the shell lifters design, while the discharge of ground particles is controlled by the grate and pulp lifters. The limitations imposed by poor grate and pulp lifter design become increasingly apparent with increasing size of ag/sag mills and their operation in closed circuit. The design of these mill components has been largely based on trial and error and hence varies considerably between manufacturers. This paper discusses the use of two state of the art design tools - Millsoft™ and FlowMod™. Millsoft™ is an effective tool to design the shell lifters and optimize charge motion, whereas FlowMod™ simulates the slurry discharge system to design grate and pulp lifters. The application of these simulators will be discussed using case studies of full scale mills.INTRODUCTIONMany large mining operations around the world have one or more semi-autogenous (SAG) mills doing bulk of the work in their size reduction operation. The SAG mill is usually followed by a ball mill to finish the size reduction prior to the concentration step. In the past when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the SAG mill operation. As a result mines have shifted their emphasis in optimization from ball mills to SAG mill"

Jan 1, 2005

By W. P. Campbell

Introduction OWING to the necessity of curtailing the length of this paper, nothing like an exhaustive treatment of the subject will be attempted. Instead, merely a few aspects will be considered, viz., water trouble in wells, sampling of waters, analysis, methods of reporting analysis, and the comparison of a few typical waters. The waters discussed will not be confined to those occurring in areas where oil or gas has already been found, but will include samples from areas in which drilling is being carried on in the hope that oil or gas may be found, i.e., from unproved fields. The Water Problem The problem of dealing with water encountered in oil and gas producing areas has engaged the attention of petroleum engineers from the early days of the industry. Water was not always considered a menace to oil sands; indeed, a certain amount of it was considered beneficial in some areas, but if such exist today they are very exceptional. In some fields, the problem is more acute than in others, and at times has baffled all attempts to solve it satisfactorily. Wells have been brought-in with promise of good production, but after a brief period have 'gone to water'. Whether ?it has always been a case of poor engineering in the form of unsuccessful water shut-off of 'top' or 'bottom' water, or because 'edge' water was present and water and oil were in such close contact it was impossible to remove the one without the other, is hard to say.

Jan 1, 1929

By D. Wolfe, K. Reid, T. Nunn

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. In order to minimize front-end rejects, and to allow for high throughput, the ore top size at Aurora has been set at a nominal 125 mm. These relatively large lumps have a significant effect on both pump performance and pipeline pressure gradient. Current design methods underestimate the solids de-rating effect of lumpy slurries in pumps, and do not accurately describe the distribution or magnitude of the lump effect on pipeline pressure gradient. Data from the Aurora hydrotransport systems has been compiled, to quantify the effect of lumps on the pump head ratio and pipeline pressure gradient, and how this effect changes as lump ablation occurs along the length of the pipeline. A model has been built, using a logarithmic curve, which predicts the effect of 125 mm lumps on pipeline pressure gradient as a function of velocity and the distance from the start of a hydrotransport pipeline. This model is applicable only to Aurora hydrotransport operation, but similar models could be developed for other operations using the same methods. Using accurate pipeline pressure gradients and pump head ratios when designing future hydrotransport pipeline systems will help improve their reliability and operability."

Jan 1, 2014

By Michael Young, Peter Allum, Mingwei Gao

"Tough economical conditions and high grade but fine-grained ore processing have forced the mining industry to look for more efficient processes. Isa Mill Technology for ultra-fine and fine grinding is one such process employed at several mining operations in Australia including Mount Isa Mines Limited in Australia. Mount Isa Mines is a business unit of MIM Holdings Limited. MIM is an Australian-based international mining and mineral processing company with around 8000 employees worldwide. Major products include copper, gold, zinc-lead-silver, coal and technology sales.The Isa Mill is a horizontal stirred mill with sizes up to 3 m3 chamber net volume and 1 120 kW installed motor. It was jointly invented by Mount Isa Mines of Australia and Netzsch Feinmahltecknik GmbH of Germany for ultra-fine and fine grinding duties in the minerals industry. Isa Mill operations started in 1994 at the Mount Isa Mines Leadzinc Concentrator and then at MIM’s McArthur River Mine in 1995. These Isa Mills have been used to liberate sphalerite and galena at Mount Isa and silica at McArthur River by grinding to less than 7 micron.This paper discusses the Isa Mill Technology and reports on the metallurgical performance of the Isa Mills at Mount Isa Mines, including work done over the last 9 years to improve mill design, process efficiency and maintenance, which has resulted in the current state-of-the-art Isa Mill Technology.INTRODUCTIONThe current leadzinc deposits at Mount Isa Mines (George Fisher, Hilton and Isa) have an average grade of 10.5% zinc, 7.2% lead and 165g/t silver. Fine grinding, in particular in the zinc retreatment circuit requiring a milled product P80 of 7 micron, is essential to treat the ores from the Mount Isa Mines deposits. Every one micron size reduction in the zinc retreatment circuit below a P80 of 10 micron improves the overall plant zinc recovery by 1%, resulting in an increase in revenue of about 1 million dollars per annum."

Jan 1, 2002

By John Folinsbee, Brian Danyliw, Tony Y. Chong

"Control of fugitive dust has become increasingly important in the mining industry both from a health and safety and environmental standpoint. Mining operations in particular have required improved fugitive dust control due to recent lowering of the allowable airborne silica concentration to which workers can be exposed. Experience has now proven that the implementation of a surfactant based chemical dust suppression system can enhance existing mechanical dust control methods resulting in much more efficient control of fugitive dust.The Porcupine Joint Venture (Dome Mine) utilizes dry secondary crushing and screening that makes it particularly prone to fugitive dust emissions. A variety of potential dust control systems were evaluated and this led to the installation of a surfactant based water spray system to augment the existing mechanical dust collection systems.A great deal was learned through the implementation of this system. This paper describes the entire process, from testing, system design and installation, through optimization and standardization of operation. In addition a variety of problems were identified, and innovative solutions were provided. Also, the metallurgical impacts on down stream processing are highlighted. Finally, a full discussion of overall results including a discussion of the relationship between silica and total dust concentrations is included."

Jan 1, 2005

By W. Greg Maybee

Separations, which form along stratigraphic boundaries in the roofs of potash mines, pose a serious safety concern. If these separations go undetected they can lead to falls of ground. The current method of identifying the location and extent of these separations is through manual scaling (sounding) using an aluminium rod. The potash mining companies would like to have a tool, which could quickly and reliably detect these separations and distinguish between them and clay seams. This paper presents the results of field trials undertaken at various potash mines in Saskatchewan belonging to the member companies of the Saskatchewan Potash Producers Association. A ground penetrating radar instrument from RST called SUSI (stepped frequency, ultra-wideband, synthetic aperture radar instrument) was used. SUSI has the ability of working over various frequency bandwidths. Four mines were chosen for these field trials, covering the different geological characteristics encountered in the Saskatchewan potash mines: Potash Corporation of Saskatchewan?s (PCS) Allan and Lanigan Divisions, Agrium?s Vanscoy Potash Operations and IMC Potash?s K2 Mine. These field trials indicated that stepped frequency ground penetrating radar technology could be ?tuned? to identify both separations and clay stratigraphy in the softrock, potash mine environment, based on the different spectral responses of the features.

May 1, 2004

By A. Taylor, J. Shelegey, H. Sullivan, J. Doucet

"Historically, performance at Vale’s Clarabelle Mill was measured by Mill throughput and Mill recovery. After the economic collapse in 2008, a series of reviews were performed to drive improvements in business efficiency. These identified that product quality (e.g., concentrate grade, variability in concentrate grade) had a profound impact on downstream processes and suggested that improved control of these parameters would generate the greatest value for the customer (the Copper Cliff Smelter) and the company (Vale). Consequently, a movement was initiated to transform the Mill operating philosophy to consider customer needs as paramount. Systems and strategies used to drive the transformation are described. In 2011, an unexpected furnace failure resulted in decreased capacity at the Copper Cliff Smelter. In response, a two-stage change in production strategy was developed at Clarabelle. The first stage was to modify the ore blend feeding Clarabelle so that the concentrate grade could be significantly increased with minimal impact on recovery. The second stage was a circuit modification to ensure the elevated concentrate grade could be sustained. Execution of the first stage was complete five days after the failure and the second stage was complete within 10 weeks. Steps involved in each stage are outlined and the overall benefits are presented.INTRODUCTION Clarabelle Mill is located in Copper Cliff, Ontario, Canada (approximately 350 km north of Toronto). The Mill treats copper (Cu) and nickel (Ni) sulphide ores. The primary diluents are pyrrhotite (Po) and non sulphide gangue rock (Rk). The process description of the circuits at Clarabelle is documented in the paper by Taylor, Doucet, Blanchette, Barrette & Lawson (2012) in this Proceedings and will not be repeated. The Mill treats ore containing Cu, Ni and platinum group elements (PGE’s) and produces two concentrates; a Cu concentrate and a bulk Cu/ Ni Concentrate (referred to as nickel concentrate). The Cu concentrate is sold to market while the Ni concentrate is thickened at the Mill and pumped to Vale’s smelter complex in Copper Cliff Ontario for further processing. Since commissioning in 1971, Clarabelle Mill has undergone many circuit changes to suit the changing needs and wants of our customers, both internal and external. The Mill processes ores of varying quality, based on mineralogy and size and until 2009 the Mill daily performance was primarily based on throughput. The second key performance indicator (KPI) of “good” or “bad” performance was quality of the concentrate and third; Mill metal recoveries. There were other plant level KPIs such as flotation feed grind size, slurry densities and mass flows to the separation circuit, but for the most part each day was good or bad depending on how many tons were processed through the Mill."

Jan 1, 2012

By H. R. Banks

IF you have ever travelled in the valley lying between the Selkirks and the Rockies in the East Koorenay district, you will have noted that the former mountains are rounded and massive, while the serrated peaks of the latter, fingering into the sky, bring an entirely different. picture. These two mountain ranges, with the comparatively level valley between, serve splendidly to introduce the subject for discussion. It is rather strange that, despite the fact that wear is undoubredly the greatest force with which human ingenuity bas to contend, it has come in for very little study from the stand point of pure science. Empiricism has been the sole ally in the fight for improvement! That we may have a clear understanding as to what we mean by wear, I would include in the term the breaking dawn of ail solid matter, from the natural wearing dawn of the mountains previously mentioned, to the hale in the mill pipe-line, which forces one to shut-down-usually at some un-earthly hour-to carry out a repair. It seems a far cry from mountains to mill launders or pipe-lines, but, magnified sufficiently, most of the materials with which we have to deal would show surfaces not unlike those we see around us. The progressive steps of wear, or ?erosion' as our geological friends would prefer to term it, are exemplified in the two ranges of mountains and the valley between. True, the wearing dawn by natural forces is a slow process. The aeons which have passed since first these mountains were formed seem endless. The natural forces pitted against them seem puny in the light of the interminable rime that has been needed to effect the changes. But here, as in the case of the materials with which we are dealing day by day, the combination of many forces ultimately brings about that condition which we describe as 'worn out'. In the case of the mountains, it is when they are finally levelled into plains, and in the case of equipment which we use, it is when that equipment will no longer serve its purpose.

Jan 1, 1943

By E. W. J. Thornton

During the past six or seven years extensive research has been performed on ore samples procured at the Bruns1,vick Tin Mines which is located in the south-west corner of New Brunswi.ck. This property was originally staked by Mount Pleasant Mines and they did considerable metallurgical and geological work on a small copper, zinc and tin deposit. In 1969, the property was obtained by the Sullivan Mining Group and after much geological and diamond drilling work, an entirely separate ore body \Vas located two miles south of the previous workings. The major economic metals in this ore zone are tungsten, bismuth and molybdenite, but many other metals exist as well. As the ore contains a host of different mineral species, it can be seen that considerable time WRS required to develop a practical flow sheet.

Jan 1, 1977

By Ian Bruce

Tailings and water management facilities are essential and integral components of mine and mill operations. They must be managed for the long term in order to ensure that safe and environmentally responsible stewardship is achieved. Toward this end, in 1998, The Mining Association of Canada (MAC) published A Guide to the Management of Tailings Facilities, which recommended the implementation of a tailings management framework (Figure 1) to integrate environmental and safety considerations into each stage of the life cycle of a tailings facility, from initial site selection and design, through construction and operation, to eventual decommissioning and closure. By February 2000 it was becoming apparent that while mining companies were making significant progress toward implementing and documenting tailings management systems, and integrating them with overall environmental management systems, further effort was warranted in their application at the operational level. In particular, a need was identified for further guidance in preparing manuals that outline procedures for the safe operation, maintenance and surveillance (OMS) of tailings and water management facilities.

May 1, 2002

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By Chuck Edwards

"Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. Over that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin close out the paper.INTRODUCTIONThe roughly oval Athabasca Basin in northern Saskatchewan occupies nearly one third of the surface area of the Saskatchewan Shield. Its sandstone-like deposits lie unconformably on the older basement. The basin hosts many high-grade unconformity-type uranium deposits(Saskatchewan Energy and Resources, 2010) for which the Athabasca Basin is world famous. Uranium production in the Athabasca Basin has come from four mills. In the order of startup these are Rabbit Lake, Cluff Lake, Key Lake and McClean Lake. General data (AREVA, 2010; Cameco, 2010; Denison 2010) for each mill are shown in Table 1."

Jan 1, 2011

By Robert E. McIvor

"The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill’s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “circuit classification system efficiency” (or CSE, McIvor, 1988a), and ultimately the discovery of the Functional Performance Equation (McIvor, 1988b, and McIvor et al, 1992). The CSE is the percentage of “coarse” (typically with reference to the plus P80) size material occupying the mill (versus “fines” or product size material, finer than the circuit P80), and can be calculated by taking the average of the percentage of coarse material in the mill feed and mill discharge. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, which is derived as follows.We define “fines” as any product size material, and “coarse” as that targeted to be further ground, the two typically differentiated by the circuit target P80. For any grinding circuit, the production rate of new, product size material (fines) must equal the specific grinding rate of the coarse material (i.e. fine product generated per unit of energy applied to the coarse material) times the power applied to the coarse material."

Jan 1, 2009

By Lee Nichols

Convergent Bitumen Recovery Context of discussion It should be noted that the CBR process is a conceptual bitumen recovery feed methodology, designed to provide supplemental bitumen to the oil sand operations of Northern Alberta. To date the following have beencompleted. ?Bench Scale testing. ?Peer group brainstorming. ?Energy Balance ?Confidentiality agreements have been signed with several companies Discussions are ongoing with industry and although conceptual atthis stage the process holds significant promise.

May 1, 2007