Search Documents

By Mi, Dong Liang, Jingyuan Bai, Victor Zhou, Xujun

Squirrel cage induction motors are the mostly used motors at present. Currently, the rotors of the squirrel cage induction motors are produced by aluminum die casting technique with the advantages of low cost of rotors. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size. Considering the huge quantity of motors, the die casting process is the best solution to produce copper rotor with economic cost. Because of the characteristics of copper, it is difficult to produce copper rotors by casting similar to that done in aluminum rotors. In order to improve the die casting quality of copper rotor, a new tooling structure was developed and the casting process of copper rotor was simulated and analyzed by Any-casting software. The filling process, solidification process, inner gas distribution and residual melt modulus were analyzed. It was found that the design of symmetrical runner and inner runner on both sides was helpful to reduce the impact of molten copper to the cavity surface during the filling process. The use of Slag traps array can reduce die casting defects inside the end rings. That will be helpful to improve the rotor quality. INTRODUCTION Squirrel-cage AC induction motors are most widely used in the world. In 2017, the total installed capacity of AC motors in China has reached more than 1.2 billion kW, and the annual power consumption accounts for about 60% of the total national electricity consumption. To improve the efficiency of squirrel-cage motor will be helpful to energy conservation and environment protection. There are several ways to improve efficiency of induction motors, using copper rotor is one of the most effective solutions. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size.

Jan 1, 2019

By S. Steinlechner

"Today the common recycling technologies of automotive catalysts are either energy intensive pyrometallurgical processes generating huge amounts of residues or hydrometallurgical ones which have to cope with effluent problems. Next to that, other valuable metals beside PGMs such as rare earths from the wash coat are not recovered.Therefore, the present paper introduces a hydrometallurgical concept developed in cooperation with the company Railly & Hill for the recovery of the PGMs as well as cerium from the wash coat of the catalysts in a closed loop. Next to the process concept, the required parameters for the different steps are discussed, including the chemical reactions, leaching efficiencies and mass flows, which form the basis for an economic estimation of the concept.Contrary to the pyrometallurgical recycling where the monolith is completely melted down to slag which is typically dumped, in this process the remaining monolith forms an utilizable product for the ceramics/refractory industry. As a result of the closed loop of the leaching media an environmentally friendly process was developed from which nearly no new residues or effluents are generated, with a sustainable usage of chemicals."

Jan 1, 2014

By J. A. Ressinger

"The purpose of this paper is to discuss some of the differences between various methods of excavating and loading as they relate to mining operations. The intent is not to provide ""pat"" answers, but instead to raise some questions and set forth some reasonable guidelines.Specifically, the paper deals with the differences and relative merits of power shovels versus rubber-tired front-end loaders - or, carrying this further, comparing what could be called ""stationary"" loading or excavating devices to ""mobile"" types."

Jan 1, 1972

By D. R. Murray

A four-year study was carried out to determine the ability of coniferous trees to aid in the reclamation of uranium tailings at Elliot Lake. Five species were planted: white cedar, white spruce, jack pine, scotch pine and red pine. More than 570 bare-root, two-year-old seedlings were planted on bare tailings and in areas of established grasses. A further division was made between areas of coarse and fine tailings. Over-all survival and growth of the trees has been far below expectations based on previous experience with several varieties of grasses. The criteria for assessment have been per cent survival and yearly growth as determined by plant height. Pine was superior, with 68% survival when planted in bare coarse tailings, 45% for vegetated coarse tailings and 34% for vegetated fine tailings. Cedar had the worst survival rates at 49%, 14% and 7% respectively. No species survived on bare fine tailings. The survival and growth of the coniferous trees have been related to species, environmental conditions and tailings properties.

Jan 1, 1978

By J. Lui

Inco Copper Cliff Smelter commissioned two new Inco flash furnaces in 1991/1993 as part of its S02 abatement program. Each flash furnace is equipped with a fluid bed dryer. The ~ 12 wt% water content in the concentrate filter cake, flux, reverts and sludge is removed in the fluid bed dryer. The dry solids are discharged from the dryer together with exhaust gases into the baghouses where they are separated. The dry solids are transferred to four storage bins. In September 2003, for the first time since startup in 1991/1993, a large amount of elemental sulfur accumulation was discovered on the walls, roofs and floors of the outlet side of the baghouse chambers. Several baghouse fires were experienced during cleaning and conducting maintenance work in the elemental sulfur contaminated baghouses. Laboratory scale test work at the Inco research lab was conducted to understand the mechanism. A plant solution to minimize elemental sulfur formation was implemented with success. This paper summarizes the efforts to understand and minimize elemental sulfur formation in the baghouse chambers.

Jan 1, 2007

By W. R. Smith

Introduction No commercial deposits of silica sand are known to occur in British Columbia, so all requirements for foundry and other uses must be imported. During the war, nearly 5,000 tons per year were used, all originating in Illinois and delivered to local consumers for about $12.00 per ton. Present requirements are somewhat less, but the cost is still of the same order. The relatively high cost of silica sand in British Columbia is not only a serious item for present consumers, but might be a deterrent to the establishment of a glass industry, should this be contemplated at any time. The present investigation was undertaken in an attempt to provide a cheaper source of silica sand within the Province. In 1936, a large number of beach and bank sand deposits in the lower coastal region of British Columbia were examined by the British Columbia Department of Mines, and samples were analyzed chemically and mineralogically. The deposits over the whole area proved remarkably uniform in mineral composition, consisting essentially of quartz, feldspar, ferromagnesian minerals, rock fragments, and various accessory minerals, and differing only in the relative proportions of the various constituents. In no case did the quartz content of any sand exceed about 40 percent and the average was of the order of 20 to 30 percent.

Jan 1, 1947

By Gordon Smith

ABSTRACT Gold-bearing quartz veins in the northeastern Ontario and north western Quebec mining camps are shown to have been mineralized in part by epithermal solutions. The vertical gradient of pressure during this stage of mineralization is calculated, using decrepitation temperatures of quartz and thermoelectric potentials of pyrite. The base of the Cobalt sediments, which lie uncomformably over part of the mining region, may be taken as datum level in calculating the depth of erosion into the basement below that level. The vertical extent of the epithermal gold mineralizaiton in this region is at least 9,000 feet below the datum level. INTRODUCTION IT WOULD have been difficult a few years ago to convince economic geologists that after making a series of measurements in a laboratory in Toronto, the depth of erosion which has taken place below the base of the Cobalt sediments at any place in the Ontario-Quebec mining region can be calculated to the neare.st 500 feet, or that the same series of measurements would also serve to allow a prediction of the minimum vertical depth of probable ore in a producing mine in the same region, with the same degree of certainty. Possibly it is just as difficult today, but the following description of the data and calculations may help to demonstrate the reliability of the method.

Jan 1, 1951

By M. Lahtinen

Traditionally, there have been three main methods for iron removal in the hydrometallurgical production of zinc. These methods are atmospheric precipitation of jarosite or goethite and pressurised precipitation of hematite. Jarosite precipitation is without doubt the leading and the most commonly used technology for iron removal. However, jarosite precipitation has some drawbacks, such as a low iron content (and, thus, high residue volume), high moisture content after filtration and often a high zinc content. These features make any environmentally acceptable way of using or disposing of jarosite more expensive, as compared to hematite and goethite. The importance of environmental regulations has grown in the zinc industry during the last decade, which will have an increasing effect on new investments. Hematite has several advantages over jarosite, such as a high iron content, low moisture and low zinc content. An important advantage of hematite is that it is suited for further use in the cement industry. However, until now the need for autoclave equipment has limited the spread and implementation of hematite precipitation in the zinc industry. Outokumpu Technology Oy has recently developed an alternative method for iron removal, which is the atmospheric precipitation of hematite. A patented method for precipitating hematite at atmospheric pressure is presented and compared with conventional methods for iron removal. The process conditions, the quality of the hematite precipitate and the environmental aspects are also discussed.

Jan 1, 2006

By C. J. Brown

Regeneration of hydrochloric acid steel pickle liquors has traditionally been accomplished by pyrohydrolysis. However, a number of factors have recently conspired to reduce the attractiveness of this approach. Moreover, the process is not amenable to small-scale operations. On the other hand, the standard technique for regeneration of sulfuric acid pickle liquors, which is the low-temperature crystallization of ferrous sulfate is applicable to any size operation. A similar technique has recently been developed to regenerate hydrochloric acid. Sulfuric acid is added to the ferrous chloride-bearing spent HCl pickle liquor. The temperature is then reduced to below 0°C, resulting in the crystallization of ferrous sulfate heptahydrate and liberation of free hydrochloric acid. Depending upon the crystallization temperature, variable concentrations of sulfate are left in the regenerated acid. Although this residual sulfate has an impact on the pickling characteristics of the regenerated acid, tests have shown that by adjusting the conditions, pickling rates will be at least equal to those using pure HCI, and an acceptable surface finish will be produced.

Jan 1, 2006

By John Knox

The object of this paper is to present an analysis of the major problems encountered both in the design and application of downhole drills. Particular reference is made to design features governed by: physical size limitations; metallurgical material standards; physical operating environment; range of commercial materials to be drilled; high power output required, coupled with simplicity from the operating and maintenance viewpoint; and bit design. The history of attempts to develop downhole drills is discussed, and representative mechanical configurations are illustrated. The general design and application aspects of the different types are commented on. The application of this drill type in various commercial fields, such as (a) oil-well drilling, (b) open-pit mining and (c) underground mining, is discussed, along with the limitations presently imposed by the commercial state of the art in the manufacture of accessory equipment; e.g., drill rods, air compressors, mountings, etc. Suggestions on the possible future direction of the development and application of this tool are put forth.

Jan 1, 1965

By K. Dinh

The Ground Penetrating Radar (GPR) has been studied for a long time as a non-destructive evaluation (NDE) technology for inspection of concrete structures. Currently, the most widely used technique for interpreting GPR data of concrete bridge decks is the one that based on the amplitudes measured at various interfaces such as asphalt-concrete, top rebar, or slab bottom. The assumption behind this technique is that a sound concrete deck should have the same reflection amplitude at these interfaces while any low number would indicate some sign of deterioration. Unfortunately, this assumption is not completely valid in most cases. As a consequence, the reported test results usually do not reflect real condition of concrete bridge decks in question. The main goal of this paper is therefore twofold: (1) to discuss the limitations of the amplitude analysis method, and (2) to propose a new model that interprets GPR data of concrete bridge decks. The model methodology is based on the comparison of GPR A-scans between two inspections, using the so-called correlation analysis. The results, indicated by the correlation coefficients, are then employed to develop a contour map that estimates different levels of deterioration. The model is then implemented to a case study in order to illustrate its methodology.

Aug 1, 2013

By L. H. Smith, D. S. Taylor

"AbstractSherritt has been applying hydraulic drives to concentrator equipment since 1967. The initial application was made on a bank of 5- by 5-in. slurry pumps. This has now been extended to all slurry pumps requiring less than 40 hp and several conveyors which require variable-speed or low-speed/high-torque characteristics. The pump motors are directly connected through a flexible coupling, whereas the conveyor systems are directly mounted onto the head-pulley shaft extension.The different applications and design concepts will be described, with outlines of the operating and maintenance advantages and disadvantages and costs. The paper also outlines future possible applications, together with the limiting conditions, of such systems.IntroductionSHERRITT GORDON MINES LIMITED has been operating a mining division in Northern Manitoba for almost 50 years. The original mining operation was at Sherridon, Manitoba and was a copper-zinc producer. This mine was exhausted in 1948 and the mining plant was moved north to its present location at Lynn Lake, Manitoba. The Lynn Lake Mine is a nickel-copper producer. Since 1960, two new mines have been discovered and brought into production in the general vicinity of Lynn Lake. The first of these was the Fox Mine, a copper-zinc property operating at 3,000 tons per day from an underground operation. This mine started production in May 1970."

Jan 1, 1977

By T. G. Carter

"Damaging seismicity associated with deep faulting in both mining and civil excavations not infrequently occurs without warning, and often before proper mitigation measures have been put into place. Severe squeezing is also a common problem for excavating through deep major faults. While both problematic conditions are difficult to predict and characterize, there is often a need at pre-feasibility and feasibility level to more reliably estimate the possible level of risk posed by such geologic structures. This paper introduces some structural geologic techniques that have potential application for both mining and civil applications for aiding forewarning of the extent of these types of problem.INTRODUCTIONEncountering adverse faulting at depth in deep excavations, whether for mining or civil purposes can create serious economic and safety impacts. For deep mines or for deep tunnel projects, measures are available for aiding prediction of the extent of possible influence that large scale faults could create, but these techniques are rarely if ever applied as part of routine site investigation programs, or even as part of risk assessment evaluations. Several well established structural geologic methods of palao-history reconstruction have potential application for aiding forewarning of the extent of these types of potential problem by allowing estimates to be made of:• controlling stress orientations that might engender reactivation movement;• principal stress magnitudes that could lead to failure initiation, and• probable mechanisms of fault deformation - brittle (bursting) or plastic (squeezing).This paper explores several structural geological and rockmass characterization techniques that have application for unravelling fault structure of importance to deep engineering projects. Their application for mining or tunnelling purposes is advocated in conjunction with conventional rockmass characterization assessment approaches using GSI, RMR and/or Q to aid early recognition and definition of potential adverse ground condition behaviour associated with intersection of significant faulting at depth."

Jan 1, 2015

By J. P. Morris, J. T. Novak, E. A. Sarver

"A variety of reagents are utilized in coal preparation, but aside from performing their desired function relatively little is known about the behavior of these reagents within the processing circuits. Where exactly do reagents go once dosed? In this paper, we present preliminary results of partitioning studies on frother (i.e., MIBC) and collector (i.e., diesel) chemicals commonly used in coal flotation, and examine implications for water management (e.g., in closed-loop systems). Additionally, we discuss the usefulness of such data in predicting environmental transport and fate of chemicals – which is currently a top priority for industry.INTRODUCTIONThe purpose of coal preparation is to upgrade mined coal into more valuable products. Since coal is primarily used as a fuel source for electricity generation, product specifications are typically contracted to minimize unwanted constituents that detract from the overall heat value (e.g., ash and moisture) or that add to environmental pollution or other problems like corrosion at a power plant (e.g., sulfur) (Pitt & Millward, 1979). Failure to meet specifications results in a financial penalty for the coal producer (Szwilski, 1986), and thus preparation processes have evolved to simultaneously optimize recovery of valuable “clean” coal with rejection of mineral matter and moisture. In addition to advancements in equipment and circuitry, development and application of various chemical reagents has dramatically improved the performance of coal preparation processes.Contemporary preparation plants typically include multiple circuits that can be categorized by the size of particles they process: coarse, intermediate, and fine/ultra-fine (Figure 1). Coarse and intermediate circuits generally rely on size classification and gravity separations (e.g., dense-media cyclones), and do not require significant chemical reagents. However, fine and ultra-fine circuits often use froth flotation to separate coal from impurities, which requires chemical additives (Table 1). The primary additives include collectors, which coat the surface of the coal particles to render them (more) hydrophobic and thus more likely to attach to air bubbles and float; and frothers, which aid in the formation and stability of the froth that will accumulate the floated coal particles. Modifiers are also commonly added to flotation circuits to regulate pH in instances where coal or impurity characteristics may change water chemistries (Laskowski, 2001). Following flotation, coagulants and flocculants are often utilized in solid-liquid separations (i.e., dewatering or clarification) for coal products, and for tailings slurries prior to their disposal in impoundments. Coagulants function via double-layer compression1 to bring colloidal particles together, while flocculants promote bridging between the grouped colloids – and the combined result is enhanced sedimentation (Wills, 2006). Defoaming or anti-foaming agents may also be required to avoid fouling of dewatering operations."

Jan 1, 2012

By J. L. Llanca

The New Level Mine project (NLMP), the planned underground expansion of the El Teniente mine in Rancagua, Chile, is expected to reach a daily extraction rate of 137 to 180 ktpd upon achieving full capacity. Production is planned to start in the year 2017 and the current plan is to meet that target through two development phases, from the year 2012 to 2014 and from the year 2015 to 2017. To achieve the 2012 to 2014 underground development schedule, the ventilation requirements have been estimated in the range of 189 m3/s (400 kcfm), and cannot be made available without significant modifications to the current system of El Teniente. As a result, a certain number of alternatives were explored to find a solution to this shortfall, for example, adding raises to generate parallel airways and installing fans to reinforce the current ventilation system. From the alternatives studied, the installation of a second main fan (system) in parallel to an existing one was identified as the best solution, and selected for implementation, however the location was not ideal and there were concerns as to the operation of both fans once the second fan was installed. This paper presents the study used to estimate the operational points of both the current and the new fan, and to justify the parallel installation of the additional main fan. An additional computational fluid dynamics study was undertaken to validate the operational point, given the particular geometry of the fan?s location and placement, to guarantee a stable operation of the fans. Finally, the protocols arising out of this work for starting the fans, and operating them in parallel to avoid generating a stall condition and damaging the investment are discussed.

Aug 1, 2013

By R. C. E. Bray, Peter Price

"The property of Pamour Porcupine Mines, Limited, is in the eastern Porcupine area, about 12 miles northeast of Timmins. It covers parts of lots 3-6 (inclusive), cons. 5 and 6, Whitney tp., Cochrane district, Ontario. It is an amalgamation of the old La Palme, Three Nations, and Porcupine Grande properties.The first discovery on the Pamour was made in 1911. During 1911 to 1914 a small shaft was sunk on the Three Nations vein to the 200-foot level and a 100-ton stamp mill was put in operation, but only a small production was achieved. The property remained idle from 1914 to 1923. In 1924 some diamond drilling was done along the Keewatin-Timiskaming contact with some encouraging results, but the gold mineralization encountered was too low in general at the price of gold then prevailing to warrant further · work. The increase in the price of gold revived interest in the area, and the above noted amalgamation was effected in 1934. Options were taken and successively dropped by two large mining companies. Following this, exploration both on the surface and underground was started by Quebec Gold Mining Corporation, Limited. Diamond drilling in the early part of 1933 showed considerable ore in conglomerate and greywacke to the east. In the middle of 1935 Noranda Mines, Limited, assumed control and management. A new shaft was sunk and the property was ·equipped with a mill having an initial capacity of750 tons a day. This was subsequently enlarged to 1,500 tons a day.From the commencement of milling (May 16, 1936) to the end of 1946, 5,025,545 tons of ore having an average grade of 0.1327 oz. a ton ($4.64 at $35 an oz.) have been mined and milled."

Jan 1, 1954

By R. Kumar, A. K. Verma

"In this paper, an anisotropic shear behavior of rock joints is investigated under constant normal load condition (CNL). The natural rock joint roughness is transferred to artificial rock samples using room temperature vulcanizing (RTV) silicon rubber. Artificial cylindrical rock joint samples (90 mm diameter and 50 mm height) are made by mixture of cement, sand, and water in the ratio of 1:1.5:0.45 (by weight). Direct shear tests are conducted on these samples in twelve directions at 30º apart at four different normal stresses (250kPa, 500kPa, 1000kPa, and 1500kPa). Thus, 48 samples are tested in laboratory. Test results shows that the peak shear strength (?) of rock joints is anisotropic in nature due to change in morphological features in particular shearing direction. Joint roughness coefficient (JRC) is determined in each shearing direction by trial and error method using Barton’s model (1973). Further, cohesion ( c) and angle of friction ( ? )of joint surface in each direction is determined. Finally, a relationship between angle of friction ( ? ) and joint roughness coefficient (JRC) is developed. Experimental shear strength and Barton’s shear strength is compared and it is found that effect of anisotropic decreases with increasing normal stress. INTRODUCTIONRock mass is generally composed of discontinuity which refers collectively to joints, faults, bedding plane and folds etc. ISRM (1978) defined joint as a line of break of geological origin along which there is no visible displacement. Joint is three dimensional discontinuity which composed of two matched/mismatched surfaces. The presence of joints in rock mass plays an important role to define its overall shear strength, deformability behavior, in-situ stresses and hydro-geological properties. The shear strength of rock joints is important in the design of near surface/ deep geotechnical works (mining excavation, dam foundation, power plants, underground caverns, and slopes).In last 40 years, many constitutive models are developed to predict shear strength of rock joints under CNL conditions (Patton 1966; Landanyi and Archambault 1969; Barton 1973; Goodman 1976; Barton and Choubey 1977; Plesha 1987; Desai ad Fishman 1991; Amadei and Saeb 1992; Maksimovic 1992; Wibowo et al. 1993; Huang et al. 1993; Amadei et al. 1998; Indraratna 2000; Homand et al. 2001; Wang et. al. 2003; Samadhiya et. al. 2008; Asadollahi and Tonon 2010; Ghazvinian et al. 2012). These constitutive models have limitations to predict shear strength of rock joints in one direction. Till date, among all constitutive models, Barton (1973) model is widely used in practice due its simplicity. It includes parameters such as joint roughness and joint compressive strength (JCS) to quantify joint surfaces."

Jan 1, 2015

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By Bahjat Khoshaba, Bern Klein, Haixing Yan, Libin Tong, Andrew Bamber

"When a conductive or magnetic particle was put into an electromagnetic field introduced by an electromagnetic sensor, the particle can influence the electromagnetic field which can be used to characterize this particle. The electromagnetic technology based on eddy current theory was explored to investigate its potential in both the separation of minerals and the pre-concentration of a base metal ore. Samples tested in the study included the minerals obtained from Ward’s Science and the low grade copper ore particles obtained from Mount Polley Mine. The effects of mineral type, sensor frequency, particle size, particle position on the sensor surface, and particle lift-off on the magnitude and phase of the electromagnetic spectra were investigated. The electromagnetic spectra of various minerals show that it is possible to separate chalcopyrite or magnetite from tested minerals, simply based on the magnitude of the spectra. The spectra of the ore particles were determined by the mineral in the particles with the strongest signal. The effect of the pre-concentration of the low grade copper ore is determined by the association of chalcopyrite with magnetite. Direct sorting is the mechanism in the separation of mineral particles, while indirect sorting is the mechanism for low grade ores.INTRODUCTIONSensor-based sorting technologies include radiometric, X-ray transmission, X-ray fluorescence, near infrared, photometric, inductive, microwave heating and so on. Sorting not only discards barren rocks away from the concentrator but also recovers metal bearing that would be lose to the waste dump. The benefits of pre-concentration using sensor-based sorting are achieved on reduced energy consumption for comminution and reduced water usage on a volume per weight of metal basis (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Kleine & Wotruba, 2010; Knapp, Neubert, Schropp, & Wotruba, 2014; Kobzev, 2014; Lessard, de Bakker, & McHugh, 2014; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013). Amongst others, high frequency electromagnetic sensors were developed for ore sorting at MineSense Technologies Ltd. and are subject of this paper. Improving the understanding of ore heterogeneity is the basis for developing a successful semi-bulk or bulk sorting systems by incorporating the sensors in the material handling equipment (MineSense Technologies Ltd., 2016). The present study focuses on the bulk sorting potential and bulk sorting mechanisms of the electromagnetic technology in the pre-concentration of minerals or ores."

Jan 1, 2016

By T. W. Wlodek

"AbstractIn this paper a new type of durable 'spiral-rolled' drill set is introduced and its performance discussed. Efficient and economical mine drilling-depends to a great extent on durability of the drill-set employed. Premature failure of this element damages the drill bit and is costly when tungsten carbide bits are used.Time of drilling of 'spiral-rolled' drill sets introduced at present in Canada is considerably larger than for the presently used drill steel, but laboratory simulated service tests and practical field tests show that the 'drilling life' of the spiral-rolled drill set is several times that of ordinary drill steel.Some features of differential plastic deformation and differential surface rolling, so called 'spiral-rolling', are given.Relations between the drilling machine drill set and characteristics of the ore are discussed. The effect of shims on conical drill rod attachments, the mechanism of failure of drill steel, .and stresses during mine drilling, are analysed.IntroductionIN MINE DRILLING operations, the main interests are: the drilling machines as a source of working energy, the drill set as the tool transferring the working energy to the cutting edges of the bit, and, finally, the drilling characteristic of the .ore or waste rock.This paper includes a review of the possibilities of metallurgical and mechanical improvements in the drill set, with particular attention to drill steel and the attachments.For economical and efficient mine drilling operations, a durable drill rod, attachment, and drill bit are essential. Premature failure of any of these parts interferes with mining operations and is costly."

Jan 1, 1955