Search Documents

By J. F. Henderson

THE National Advisory Committee on Research in the Geological Sciences was established seven years ago - in 1949. In 1952, shortly after the Committee had really begun to function and had issued its first report, a paper ( l) was presented describing the objectives and organization of the Committee and the progress to that time. Another four years have gone by and the Committee feels a further progress report may be of interest. HISTORY Ten years ago, in 1946, the Geology Division of the Institute set up a Committee on Geological Research. This Committee, under the Chairmanship of Dr. J. E. Hawley, recommended that "a National Advisory Committ.ee on Research in the Geological Sciences be formed" (2). With the backing of the President and Council of the C.I.M. this recommendation went forward to the then Minister .of Mines and Resources and, with his approval, to the Committee on Scientific and Industrial Research of the Privy ?Council. As a result, the National Advisory Committee was set up in 1949.

Jan 1, 1956

By H. E. Miard

"IntroductionIT HAS BEEN SAID, with good reason, that the future of the coal mining industry, in our mountainous regions at least, depends on ability to extend operations successfully to depths greater than those reached until now. However, at many points, Nature has given definite hints that trespassing there could be fraught with very un-pleasant possibilities, unless the intruder be governed by a series of rigidly observed principles. In the coal mines of British Columbia, so far, bumps have taken place only at the Coal Creek colliery, but there they gave ample evidence of the extent to which they can hamper underground operations. Some of these manifestations have also been experienced at the McGillivray Creek colliery, in Alberta, at Carbonado, in Washington, and at Sunnyside, in Utah.Cognate phenomena, known as 'air blasts', have been experienced also in some deep metalliferous mines in British Columbia. Such occurrences were responsible for three fatal accidents at the Le Roi and War Eagle mines, near Rossland, in 1916 and 1917.In more or less disturbed coal fields, another form of stress release, equally detrimental, has been still more generally experienced than have been the bumps. Coal outbursts have taken place at Morrissey and Coal Creek, in the Crow's Nest Pass district, and at Cassidy, South Wellington, and the Nanaimo Reserve colliery, on Vancouver island. Manifestations of this kind have been made the subject of intensive study in European countries where they occurred on a really impressive scale, which must not be construed as meaning that some of our own outbursts did not approach a comparable magnitude."

Jan 1, 1953

By C. D. Williams

The following paper deals with some of the aspects of the law as it relates to the oil and gas industry in the Province of Alberta, but it should be stated here that consideration of this large subject will be confined to discussion of only those laws, rules, and regulations which affect actual exploratory operations. The paper will not touch on those branches of the law which deal with such matters as income tax, customs, and other kind red subjects which are of a highly technical nature and which are more properly the field of the specialist. Generally speaking, any system of law consists of certain major components. There must be, firstly, a national authority capable of ensuring the existence of the state itself and of maintaining the stability and continuity of its institutions; secondly, a philosophy of government covering the relationship of the state to the individual and of the individuals to one another; thirdly, a body of law to effect the purposes of the philosophical principles; and, fourthly, a judiciary to arbitrate any disputes that may arise from such relationships. All of these components and the system itself are, of course, subject to a varying degree of modification with the changing times and with the influence upon them of other systems of law. Now. while it is true to say that all systems of law comprise these similar basic features, it is apparent that the end result of any two systems of law in their impact upon the individual may be quite different.

Jan 1, 1951

By J. Guha, A. Gobeil, P. Pilote, A. Tremblay, E. Dimroth

The Mount Bourbeau Lac Berrigan area is located just to the north of the Town of Chibougamau. The axial trace of the Chibougamau syncline borders the northern part of both areas. The area contains Archean rocks of the Roy Group, intruded by the Cummings Complex and the Line Lake tonalite stock. Proterozoic sedimentary rocks occur in a series of outliers. Various Cu, Zn, Pb, Ag, Au and Mo showings are dispersed over the area in a wide range of time and space. Pre-Kenoran (stratiform and stringer) showings related to volcanic activity may be distinguished as well as the syn-or post-Kenoran (vein) types whose nature is imprecisely known. In this area, the stratiform showings occur in the Gilman and Blondeau Formations, whereas the vein type showings occur for the most part in fractures or breccias within or along the contacts of the various sills of the Cummings Complex. Mount Bourbeau is distinguished by the greatest variety of showings as well as the proximal volcanic facies of the Blondeau Formation. A volcanic centre is presumed to lie a short distance north or east of the locality. Locally, the Line Lake stock contains significant silver, molybdenum and gold mineralization. Its role as a metal reservoir, a source of heat for the circulation of hydrothermal fluids and its control of the local tectonic style remains to be determined.

Jan 1, 1984

By E. Sharifi, B. Komishke, R. Heffel, D. Schwartz

"The oil sands resources in Canada are one of the world’s largest hydrocarbon deposits. Processing of oil sands uses hot water to extract bitumen. The process generates tailings slurry that must be settled for final deposition. The tailings contain fine material, with poor water release characteristics which makes water recovery challenging. Polymer flocculants are added to assist in settling and dewatering the fine tailings. The amount of polymer addition is dependent on tailings characteristics, including the particle size distribution (PSD). If the PSD of the tailings is unknown, an excess amount of polymer needs to be added in the dewatering stage to flocculate the particles. Over flocculation also has a detrimental effect on the water release characteristics. Measuring the particle size distribution using an on-line analyzer could have major benefits over common laboratory methods as it provides online and fast insight into the process enabling the operators to implement required changes to minimize the reagent consumption, while achieving optimal flocculation. Online measurement of PSD using laser diffraction has long been used in base metals beneficiation processes. A series of test work using Outotec PSI500® particle size analyzer on oil sands samples from different operations have been conducted. Tests were performed by recirculating the slurry in closed circuit to simulate real plant conditions. This paper presents a summary of the results.INTRODUCTION Canada’s oil sands are the third largest reserves of crude oil in the world, with an estimated 165.4 billion barrels of recoverable oil (Government of Alberta 2016). Oil sands are a mixture of sand, water, clay and bitumen. Bitumen is a form of oil that is too heavy or thick to flow or be pumped without being diluted or heated. About 20% of bitumen reserves are close enough to surface to be mined. In mining methods, oil sand is transported from an open pit mine to the processing plant and bitumen is separated from solids and water. The separation process involves ore preparation, such as addition of hot water, steam and caustic (NaOH), followed by gravity separation and froth treatment (Masliyah et al. 2004). A general scheme of the extraction process is presented in Figure 1."

Jan 1, 2018

By F. R. Nogas

"Because of the elements of uncertainty and instabilitp associated with single-enterprise communities, there is increasing interest in the alternatives to developing additional new communities of this nature. Gulf Minerals Canada Limited has chosen a unique alternative means to accommodate employees at a new uranium mine/mill complex at Rabbit Lake in Northern Saskatchewan. Gulf has adopted a fly-in program which moves their staff from a 450-mile radius, in and out of the on-site facilities, on a 7-day rotation."

Jan 1, 1976

By W. H. De Blois

Introduction In the contact process for ?the manufacture of sulphuric acid, sulphur dioxide gas - produced by the burning of sulphur or of sulphur-bearing ores, or as a by-product in the treatment of sulphide ores - is made to combine with the oxygen of the air to form sulphur trioxide, which then only requires the addition of water to form sulphuric acid. The substance, as for example platinum, causing this combination is usually referred to as a catalyst, a convenient term, in the definition and explanation of which many pages have been written. Catalysis is now a comparatively common means of effecting chemical combination, but if the question were raised here tonight as to what actually goes on when this apparently innocent third party unites the parties of the first and second . part, without itself being altered in any way, I am afraid even our most learned members would have to confess their inability to entirely explain the phenomenon; for although the subject is under investigation, there is still much to learn. The contact process, however, is one of the outstanding achievements in chemical engineering. ? From the standpoint of the difficulties involved and the time absorbed in their solution, it probably stands alone in the field of technical chemistry. In fact, the manufacture of sulphuric acid has, from the earliest days, been surrounded with problems which have interested the ablest chemists. The Chamber System Although this paper has particularly to deal with the contact process, it may not be amiss to refer briefly to the chamber system, which was, and still is, a most important factor in the sulphuric acid industry.

Jan 1, 1927

By H. W. Manley

SULPHUR, like the minerals of coal, iron and petroleum, is one of the essential materials in our modern expanding industrial civilization. Before discussing the salient features of the production of sulphur from the Canadian sour gas, it seems appropriate to outline the historical past and probable future utilization of sulphur. The ancient Greek writer Homer spoke of its "pest-averting sulphur" and the "divine purifying fumigation". Ancient alchemists found sulphur to be a fascinating and baffling material. The discovery of gun powder in the year of 1250, and its application to the art of war a, century later, made sulphur an important commodity in the progress of mankind. The initial manufacture of sulphuric acid in the year of 1736 by the Englishman Joshua Ward, established the basis of a chemical industry that today utilizes 80 per cent of the consumption of elemental sulphur. Commercial production of the chemical soda ash ( N a2C03) discovered in 1787 by the famous Leblanc Process, in-creased international demand for the element sulphur and marks the birthday of the Sicilian sulphur industry.

Jan 1, 1961

By G Anders

Underground tests of slusher cables at first might seem to be quite simple and inexpensive. They do, however, take a long time and give results that may be ambiguous and unreliable. Also, because underground test conditions are not exactly duplicable, tests carried out at different times or in different mines could not be compared. An attempt was made to develop a laboratory test method that would provide for all factors affecting slusher cable performance underground in such a way as to make it possible to achieve comparable results from different series of tests by exactly duplicating test conditions. Such a method should also make it possible to vary individual factors systematically in order to give a proper assessment of the effect of changing conditions on cable performance. A set of tests, comparing the same two types of cable both underground and in the laboratory, is described. AN assignment at the Algom Nordic mine called for the comparison of two types of %-in. slusher

Jan 1, 1964

By T. J. Wells

THE blast furnace is the base of the steel industry, since there is no commercially practical way of converting iron ore directly into steel. In three hundred years, the blast furnace has developed from a small unit using charcoal as fuel and producing about one ton of iron in twenty-four hours to a furnace making upwards of 1,500 tons a day. The principle of the blast furnace is briefly this: A descending column of stock, consisting of ore, fuel, and flux, is met by an ascending stream of gases, consisting in part of gases formed by the combustion of the fuel and in part of pre-heated air which is blown into the lower part of the furnace. The flux combines with the impurities in the ore and the ash in the fuel to form slag, which is drawn off as liquid.

Jan 1, 1943

By M. J. Latva-Kokko, T. J. Riihimäki

"Oxidation autoclaves are normally operated at elevated temperature and pressure. The improvement in kinetics is due to combined effect of temperature and partial pressure of oxygen. In this paper exclusive effect of pressure has been studied with a low grade sulphide ore at below 100 °C temperature. These studies are related to development of a novel tower-like reactor that utilizes hydrostatic pressure. Technology is designed to generate high amount of effective fluid volume for high solid content slurries with lower energy consumption and improved kinetics compared to normal atmospheric operation.INTRODUCTIONEconomical utilization of low-grade ores requires handling of enormous amount of material. This sets new requirements for process equipment in terms of size and energy efficiency. For example on the field of mineral processing this has lead to a six fold increase in the operating volume of mechanical flotation cells over the past two decades. Ore beneficiation methods like flotation greatly reduce amount of material that needs to be further processed in smelters or hydrometallurgical refineries. However with some ore types, such as nickel laterites and refractory gold ores, traditional concentration technologies cannot be utilized. Thus direct leaching of ground ore could be an attractive option. In many cases normal atmospheric tank leaching has traditionally been a non-feasible option mainly due to high capital and operational expenses induced by large amount of stirred reactors required. Main restriction for increasing reactor size to beyond 500 m3 has been mechanical load and power requirements set by mixing in cases when high dispersion efficiency of gas is required. THEORETICAL BACKGROUNDIn hydrometallurgical industry autoclaves are typically operated at elevated temperature and pressure. In many cases increase in operating temperature is the desired phenomena and improvements in kinetics are strongly related to that. Thus increase in pressure might be induced solely by water vapor pressure. However when gaseous feed is present, pressure itself has a strong effect on leaching kinetics for various reasons and its role should not be neglected."

Jan 1, 2012

By A. M. Cameron

THE HOISTING PLANT at the Stobie section of the FroodStobie mine is a two-shaft installation designed to handle a daily production of 18,000 tons of ore at depth. The two vertical shafts are within 100 feet of -each other, an arrangement made to provide the needed capacity and to give flexibility of operation (Figure 1). No. 7 shaft, used for handling men and supplies as well as for hoisting ore, has been sunk to the 3000 level and is served by a manhoist handling two cages and an orehoist with two 14-ton capacity Kimberley skips. No. 8 shaft, so far completed to a depth of 1,900 feet, handles only ore. The hoist is semiautomatic with push-button control and the skips are 15-ton capacity bottom-dump. The ore-loading pocket for first stage hoisting at both shafts is 120 feet below 1,600 lev-el and additional pockets are planned, as the shafts are deepened, at 800 foot intervals down to 4,000 feet.

Jan 1, 1956

By Jon Errey, Aleksandar Petrovic, Karl Haase

"Developing a gold deposit of this magnitude in the Amazonian jungle of Guyana posed many challenges. This paper describes not only the process & logistical challenges arising from the remote mine site location in a tropical environment with a local industry unaccustomed to recent large scale gold mining operations, but also the innovative technical solutions employed to address the unique ore body characteristics. The best examples of this approach were dealing with the initial high clay content saprolite ore from the development phase and primary mining pits whilst ensuring that the design also implemented the right method to deal with the future fresh rock in an environmentally sensitive habitat. In order to do this separate individual crushing flowsheets were generated, focusing on the specific material handling equipment that would be suitable to handle these various types of material and ensure high recoveries were maintained.INTRODUCTIONAurora gold mine is located in forested region of Guyana, 170 km west of capital Georgetown, and 130 km West North-West of Bartica, a settlement at the junction of the Essequibo and Cuyuni Rivers.The Aurora gold project (Aurora) is a 5,000 tonne per day open-pit/underground operation, which will produce a total of 3.29 million oz. gold – averaging 194,000 oz. per year – over an initial 17 year mine life. At the final investment decision in 2014 Aurora had a total resource of 6.54 million ounces in the measured and indicated categories (62.83 million tonnes at 3.24 g/t Au) as well as additional 1.82 million ounces in the inferred category (16.93 million tonnes at 3.34 g/t Au)."

Jan 1, 2016

By A. Klingberg, M. Svensson, N. Smolko Schwarzmayr

"Removal of silicates and carbonates from sedimentary phosphate ores by the use of new synthetic collector/formulations was investigated in a comparative study with traditionally used collector systems as references. In the direct carbonate flotation the new formulations showed higher efficiency, contributed to an improved balance of P2O5 recovery and P2O5 enrichment in the recovered material. Efficiency of the new formulations containing synthetic surfactants was 1.5–2 times better than potassium salt of fatty acid sulfonate based formulations that are traditionally used for that purpose. The new formulations also provided up to 7% increase in P2O5 recovery at the same P2O5 grade. The new synthetic collectors for removal of silicates showed extremely good selectivity towards silica bearing minerals. The selectivity factor for the flotation tests when new formulations were used was 32–52 and for the flotation tests with the traditional collectors: 20–32. The ratio between distribution of an amount of silicates (as SiO2) and distribution of phosphate in the froth (waste) is defined as the selectivity factor. The new formulations provided more than 2% decrease of the amount of SiO2 at the same P2O5 recovery.INTRODUCTIONPopulation growth and decrease of arable land are the main reasons for constant increase of consumption of apatite (phosphate ore) in the fertilization field (Lannefors, Gorochovceva, Klingberg, Lima, & Gustafsson, 2015). Fertilizers play a key role for farmers to produce more with less land. The phosphate component of the fertilizer is vital for producing healthy and large amount of crop. As a result the demand for phosphate rock is growing.The largest producers of phosphate rock are the Unites States, Morocco, Tunisia, China, Russia, and Brazil. The term “phosphate ore” includes all phosphate-bearing minerals and rocks, but only two of them are of industrial interest: apatite (igneous origin) and sedimentary phosphate (Peres, Araujo, El-Shall, Zhang, & Abdel-Khalek, 2007). The majority of the world’s phosphate deposits are of the sedimentary type. There are two different types of sedimentary phosphates: siliceous and carbonaceous which are categorized based on gangue minerals (such as quartz, carbonates, mica, and clay)."

Jan 1, 2016

By Harry Jomini

Introduction The Wakefield plant of the Aluminum Company of Canada, Limited - a member of the Aluminum, Limited, group of companies - produces magnesia, magnesia fertilizer ingredient, and hydrated lime, from brucitic limestone. Wakefield is on the Gatineau river in Wakefield township, Quebec, some 22 miles north of Ottawa. The plant is near the western bank of the river adjacent to the Ottawa-Maniwaki highway and branch line of the Canadian Pacific railway. The plant is unique in the sense that it is the only place in Canada where brucite is processed. It is also distinguished for its outstanding safety record, as not a single lost-time accident occurred during either 1948 or 1949. The plant is amply provided with safety and comfort provisions in keeping with the standard practice in all of the twelve plants operated in Canada by Alcan and its associated companies. History Following the identification of brucite in the Rutherglen and Bryson districts in Ontario, occurrences of the mineral were discovered in the Wakefield area, Quebec, in 1939. After exploratory work on these deposits and investigation by the Bureau of Mines, Ottawa, on a method of extracting the brucite from the ore, a plant for treating the ore from the Maxwell property was built in 1941 by the Aluminum Company of Canada and commenced operations in early 1942. The process used is more or less in accordance with the method worked out by Mr. M. F. Goudge of the Bureau of Mines.

Jan 1, 1950

By V. S. Papezik

Pyrophyllite, a hydrous aluminium silicate, is used mainly in the ceramic industry and to a lesser extent as a filler in the manufacture of paper, rubber, insecticides and baby powders. Commercial deposits of pyrophyllite in North America are restricted to the "Avalon Zone" , a belt of late Precambrian volcanic and sedimentary rocks that extends along the eastern flank of the Appalachian orogenic belt f rom Georgia to Newfoundland. The only commercial Canadian pyrophyllite deposit lies near Foxtrap on the A valon Peninsula of Newfoundland. Here, steeply dipping lenses of altered pyrophyllite rock occur in a north-trending rhyolite belt near the contact with a granitoid pluton. The altered rock is massive, light greenishyellow and contains varying proportions of pyrophyllite, sericite and quartz with lesser amounts of diaspore and traces of barite and rutile. A lteration was produced by acid solutions, either derived from or activated by the intruding pluton, at temperatures of 250° to 270°C and pressures not exceeding 2 kbr. The largest of the Foxtrap pyrophyllite lenses, discovered in 1897, was mined intermittently f rom 1903 until the early 1950s. The present owner of the mine, Newfoundland Minerals Limited, acquired the property in 1959 and ships between 27, 000 and 36,000 tonnes annually to th e company plant in Lansdale, Pennsylvania, for use in ceramic tile.

Jan 1, 1984

By G. A. Bezuidenhout, J. Davis, S. M. Bradshaw, J. P. T. Kapusta, D. K. Chibwe

"This research work forms part of an assessment to complement the feasibility of implementing high pressure sonic injection into relatively small (2.25 m I.D by 3.66 m I.L) Peirce-Smith converters (PSC) used at Lonmin Plc. Work has been carried out to characterize the fluid dynamics of three-phase (air, matte and slag) fluid flow in these converters using Computational Fluid Dynamics (CFD) simulations. The investigation has been done to study the flow pattern of the three phase system at high air pressure injection achieving sonic velocity at the tuyere exit into the converter. The 2-D and 3-D simulations of the three phase system were carried out using the volume of fluid (VOF) and realizable k -e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were implemented using the commercial CFD numerical code FLUENT. A detailed study of the flow pattern has been presented in the form of contour plots and the results obtained are useful for understanding plume extension and velocity distribution, shear wall stress distribution, and phase distribution characteristics in the system. The results provide a basis for further development of sonic injection technology into relatively small industrial Peirce-Smith converters with the ultimate objective of achieving lower energy consumption, improved process efficiency and increased throughput of the converting process. INTRODUCTIONPeirce-Smith converters (PSC) have been used in copper (Cu) and nickel (Ni) making smelters for more than a century for the purpose of removing iron (Fe) and sulphur (S) chemically associated with copper-nickel mattes through exothermic oxidation reactions. This process is commonly referred to as conversion. In principle, conversion is a submerged injection process, where typically air (or oxygen enriched air), at subsonic velocity (typically < 150 m/s), is laterally blown into liquid matte (Cu-Ni-Fe-S system). Oxygen preferentially reacts with Fe and S to produce iron oxide (FeO), which is slagged off, and sulphur dioxide (SO2), which reports to the process off gas."

Jan 1, 2012

By W. W. Heywood

"IntroductionCIRCULAR structures on the Arctic islands were first noticed early after World War II. During the indexing of the 1950 Royal Canadian Air Force photographs their occurrence was brought to the attention of the Geological Survey of Canada by Mr. W. B. Waugh, Surveyor General. As a result, I. C. Brown ( 195l) of the Geological Survey of Canada studied the air photographs of these structures and discussed theories that might explain their origin. The author, as a member of the Geological Survey of Canada, spent several months in 1952 and 1953 in reconnaissance study of the geology of Ellef Ringnes island, using the Isachsen meteorological station as a base. Twelve days in the summer of 1953 were spent mapping the Isachsen dome and adjacent areas. The Isachsen dome, one of several similar structures occurring on Ellef Ringnes island, is situated 35 miles southeast of the meteorological station.PhysiographyEllef Ringnes island is a mature, stream dissected plain having an average elevation of about 400 feet. The surface of the plain is undulating with a relief of about 150 feet; only a few of the numerous streams that form a dendritic drainage pattern have eroded valleys this deep. Long, low, cuesta escarpments cross' the plain, which is underlain by sedimentary rocks of Lower Cretaceous and possibly younger age. The sedimentary strata have a low regional dip to the southeast; exceptions are found in the vicinity of the domes, where the strata are up-turned, and in the plateau region, northeast of Deer bay, where they are flat lying. The plateau, which is underlain in large part by basalt, is deeply dissected and has an average elevation of 1,000 feet."

Jan 1, 1955

By Douglas R. Piteau

"Assessing the stability of a slope cut in rock is basically a problem of engineering geology - geology, because it involves a sound understanding of the important aspects of geology, such as geological structure, ground water, weathering and other natural phenomena, which all relate to or exist in a geological environment, and engineering, in that quantitative evaluations and calculations are necessary, these being based on mechanics and relating to the strength of the geological materials and the forces causing instability of the slopes. The engineering geologist must make every attempt to. provide, in a quantitative way, information on those geological factors which are necessary for making calculations of the probable stability of the slope. These include numerical assessments of quantities relating to the characteristics of structural discontinuities, rock types, topography, hydrogeology, tectonic history and other environmental factors. Based on the development and extension of these general principles, both preliminary and final slope stability studies of some open pits in South Africa, Swaziland and Zambia have been conducted. Some of the basic concepts and techniques developed to carry these studies out are described."

Jan 1, 1972

By J. H. Brown

"THE need for continuing education has been recognized only in fairly recent years as a major concern of the engineering profession. Formerly, it was acknowledged that engineers were required, at least informally, to follow the professional literature and to give some attention to new technical and technological developments. However, those relaxed days, when progress could be followed in a casual or incidental evening of reading, have disappeared in these days of mushrooming information. The engineer is now in the position of the man trying to control the flow from a fire hydrant with a child's pail. Our problem is that of developing an effective flow system -be it trough, hose, pipe or a bigger pail.The first step in achieving an effective means for continuing the education process is to realize that the need for the system is really an outgrowth of an increasingly sophisticated society. It is merely one more symptom of that society; others would• include the facts that new engineering graduates are more highly trained than those of several years ago, that graduate schools are now the norm and that even some fairly recent technologies are becoming outdated. There-fore, let us examine the education-al systems from which the bulk of the increasing sophistication has grown."

Jan 1, 1966