Search Documents

By Alf Hartling

"Most of the Paleozoic section of the Williston Basin is a thick accumulation of numerous carbonate to evaporite, shallowing upward, cyclic sequences. These sediments were deposited in broad epeiric seas, and the deposition of the evaporite facies marked the final stage of each cycle. Many of the sequences display a pervasive replacement dolomite in the uppermost portion of the carbonate units. This secondary dolomitization is, at least in part, an early diagenetic event, synchronous with evaporite deposition.The inception of evaporite precipitation resulted in the seepage of a dense, Mg-rich brine into the underlying sediment. The heavy brine moved down the gentle regional dip displacing the more normal marine interstitial pore fluid and dotomitized the primary calcitic sediments en route. The supply of Mg-ions decreased away from the source, and correspondingly, the degree of dolomitization decreased and larger crystals formed because of slower nucleation at fewer sites.The seepage refluxion of dolomitizing brines gave rise to the frequently observed textural variation of cryptocrys talline, impervious dolomite grading into a finely sucrosic, permeable dolomite down-dip. This diagenetic facies change provides the critical up-dip barrier for potential hydrocarbon reservoirs. The lateral pool boundaries are controlled by either structural relief or a similar diagenetic facies change. The reservoirs are capped by the tight evaporites.Hydrocarbon production is attained from diagenetic traps in the Mississippian Oungre Zone and the Ordovician Red River 'C' Zone . Reservoir creation and the pooling mechanism are the result of dolomitization by the seepage refluxion of dense, Mg-rich brines beneath restricted, hypersaline lagoons. When formulating an exploration/ exploitation program for these oil prone horizons, it is essential to understand the complete geological history in order to establish where the reservoirs will be found and to define the areal extent of each accumulation."

Jan 1, 1984

By Ruan Chi, Zhenyue Zhang, Zhengyan He

In order to understand what governs the leaching of exchangeable rare earth (RE) and impurities and enhance the RE leaching process, the effects of the concentration of ammonium sulfate, pH and leaching temperature on the migration of RE and aluminum (Al) during the leaching of weathered crust elution-deposited rare earth ore was studied. The elution curves for ammonium ion (NH4 +) were also studied to reduce the consumption of the leaching agent. It was found that a high concentration of leaching agent can enhance the leaching process of RE and Al, reduce the breakthrough volume of NH4 + and more rapidly obtain the equilibrium of NH4 +. However, excessive leaching agent can both increase the cost and the burden on the environment. There is almost no variation on the elution curves of RE and Al in the pH range of 4-8 and control of the pH of the leaching agent can be omitted. It is better for the leaching work to be done in summer since higher temperatures can enhance the RE leaching process and improve the use ratio of ammonium. Using 0.1 mol/L ammonium sulfate for leaching 250 g RE ore, 95.42% RE extraction can be obtained when the volume of leachate is 102.6 mL. At this moment, only 18.17% of NH4 + is used to exchange RE and 49.22% of NH4 + is left in the leachate that can be reused as leaching agent by replenishing ammonium sulfate. The results of our studies can provide theoretical guidance for high efficiency and low consumption exploitation of RE ores.

Jan 1, 2016

By Jacque Turgeon, Gontran Foy

"The Mineral Research Centre of the Quebec Department of Energy and Resources has worked extensively on the development of a dry process to extract pure mica flakes from a phlogopite ore. The liberation of mica from the gangue is effected basically by impact crushing, and the ground ore is screened into several fractions, each having a fairly narrow range of grain size. Each sized fraction is then fed to an air separator where heavy grains are separated from light flaky grains. Heavy fractions are returned to hammer mills where gangue minerals are ground finer and blocky mica particles are exfoliated. A second stage of screening is performed and each fraction is sent to an air separator. This sequence is repeated until mica products are virtually free of gangue. These different fractions are then treated in a cage mill in which mica flakes undergo a more orderly exfoliation along cleavage planes. The ground mica is again submitted to a final screening stage, after which each fraction constitutes a final commercial product.This process permits the recovery of about 70% of the mica contained in the ore. The over-all process will be described along with technical details of each unit operation. Recent work on a wet grinding method to produce very fine mica will also be discussed.IntroductionRecords of production of mica in Quebec date back to 1886. Production has been more or less continuous since that time, with peak activity during the war years. Production was interrupted in 1966, but started again in 1972 when Marietta Resources and Laviolette Mining and Metallurgical Corporation started their joint operation in Canton Suzor, northwestern Quebec. Mica deposits of more or less importance exist in different parts of Quebec, of which three have attracted attention in recent years: the Canton Suzor deposit, the Canton Lamy deposit and the Canton Chasseur deposit. The Suzor orebody was first identified by Carl Faesler in 1936, who described the rock as ""brown biotite in flakes half an inch in diameter, with interstitial augite, apatite and feldspar""."

Jan 1, 1982

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"Abstract-A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995

By Gary S. Anderson

Rajant Corporation is the global leader in mining communications systems implemented a vision to develop a wireless network that is rapidly deployed, self-powered and managed, for portable or fixed configurations ? Mobile, Portable, Self-Powered, Secure and High Bandwidth. The network configures itself allowing for very rapid deployment without the time delay and personnel typically required for set-up and configuration. Rajant?s proprietary technology ?InstaMesh®? is incorporated in a device called a BreadCrumb®. Rajant has filed several patent applications on its proprietary technology and has received trademark protection on its brand names. The BreadCrumb® uses technology which allows mining, military and first responders to easily establish internet connections at remote sites or situations where existing internet communications has been disrupted. The BreadCrumb® products are standards-based Wi-Fi 802.11 a/b/g compliant, ruggedized, lightweight, portable; self-meshing and the system can be established by just turning on several of the BreadCrumb® units. The Rajant Network has evolved in the ?One Network? philosophy and has been deployed by both the military and homeland defense organizations. With multiple radios, transmitting on multiple frequencies as the same time, bandwidth is doubled, the speed of the network is enhanced, management is simplified, and manageability is made easier. Rajant has partnered with world class integrators and partners, including ten CAT dealers, a world-wide mining technology company, a mining and construction software company and leading technology innovators in mining automation and operations. Recently, Rajant provided a significant network to Rio Tinto?s Iron Ore of Canada Mine in Labrador City, Newfoundland, Canada, Kennecott Utah Copper Mine, and is currently the wireless standard at Peabody Energy and several mines in Australia. These networks range from 20-250 BreadCrumbs®. The result is a meshed mobile broadband network capable of operating in a vast open pit active mining space. Simultaneous applications currently running on these BreadCrumb® networks in the mining sector consist of Caterpillar?s VIMS?s, CAESultra grade control and Aquila Drill Management Systems, Carlson Grade Control systems, Jigsaw Technologies and Modular Mining fleet management system, Ground Probe Radar, an Automatic Train Operation and various video and VoIP applications. All vendor applications have been turned off and all applications are running on Rajant?s ?One Network?.

May 1, 2010

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995

By M. Okada

Consumption of refined copper in Asia, especially in China and India, has soared, and the copper price is at its historic height. New smelters and refineries have been built in the region with state-of-the-art technology to meet the unprecedented demands. Supply of copper concentrate, on the other hand, has fallen short of the growing demand for concentrate by the smelters and refineries with expanded production capacities. The shortage of copper concentrate is attributable to the delay in the mining development, caused by the prolonged price slump of before 2005. The mismatch between supply of concentrate and smelting and refining capacities may cause disorderly movement of copper price, and hamper the sound development of the industry. The recent high copper price may prompt substitution with alternate materials. With electrical and thermal conductivity and workability, copper is one of the most customer-friendly materials. It is regrettable for both customers and suppliers if the high copper price would become an impediment to promoting copper use. Some outdated and environmentally unfriendly facilities still operate. In view of recent lower-grade copper concentrate with higher sulfur content, these facilities must reform their equipment to environmental-responsive one. The current level of per capita consumption of refined copper in Asia shows that the demand of copper will further grow. It is necessary to realize stable supply of refined copper and stable copper price, to help developing countries including China and India to economically take off. Hence, it is essential that the development of the copper industry be accompanied by environmentally friendly facilities, and harmoniously increased capacities between mining and smelting and refining.

Jan 1, 2007

The tensile test results of as-cast A356.2 grain-refined alloy castings show that the tensile strength can be improved by strontium modification (`SrM'), superheating at 900°C OM, and melt thermal treatment of the Sr-modified alloy melt (`SrMTT'). Both SrM and SrMTT processes can greatly improve the ductility (percent elongation) of the as-cast alloy. During solution heat treatment at 540°C, eutectic Si particles undergo fragmentation, spheroidization, and coarsening, thereby affecting their morphology. The effects of solution heat treatment on the tensile properties of the variously treated A356.2 alloy castings can be summed up as follows: the yield strength of the castings is significantly improved after 8 h solution heat treatment due to the precipitation of Mg2Si, after which it remains more or less the same with the further increase in solution treatment time up to 80 h; the ultimate tensile strength is also greatly improved within the first 8 h of solution heat treatment and then remains at the same level thereafter, up to 80h of solution treatment. The improvement in UTS is attributed to Mg2Si precipitation, dissolution of Si within the aluminum matrix, and changes in the Si particle morphology (spheroidization). The ductility of the as-received grain refined non-modified (`NM'), grain refined and superheated at 900°C (`SH'), and melt thermal-treated grain refined (`MTT') A356.2 alloy castings can be improved considerably with solution heat treatment e.g. from ~6% in the as-cast non-modified casting to ~10% after 80 h solution treatment.

Jan 1, 2011

By M. Pierce

Empirical relations exist for the estimation of rock block strength at scales larger than standard core sizes. Two recently published relations account for the significant impact that microflaws (pores, open cracks, veins) and weathering/alteration can have on scale effect. These relations were used to estimate the rock block strength of heavily microfractured quartzite from the Bingham Canyon Mine. Predictions were compared to the results of Uniaxial Compressive Strength (UCS) tests conducted on cylindrical core samples of varying microfracture intensity and diameter. The comparison confirms the sensitivity to microfracturing suggested by existing relations and suggests that they would benefit from more detailed consideration of microfracture strength, density and persistence over a range of scales. The results of a numerical study illustrate how Synthetic Rock Mass (SRM) modeling techniques could be used to complement empirical data in the development of such relations.

May 1, 2009

By John D. Smith, Robert J. Mitchell

"There is a world-wide trend toward underground bulk mining methods employing hydraulically placed backfill. This trend is recent and therefore there is little in the literature to assist an operator in the design of backfill properties, the design of drainage facilities, the calculation of the operating forces on a bulkhead, and the control procedures considered necessary before, during and after pouring. This paper presents recommended procedures that are based on over to years of experience in the various aspects of backfilling large openings. Free-draining timber or concrete block bulkheads are shown to be a viable alternative to massive reinforced concrete bulkheads for the containment of backfill pours. Hydrostatic pressures cannot develop in backfills provided adquate drainage facilities are installed.IntroductionThe increasingly adverse relationship between mining costs and mineral values has led mining companies to develop more productive, lower-cost, bulk mining methods. This has led to the increasing use of large, more or less continuous, hydraulically placed backfill pours to enable the recovery of a higher proportion of pillar ore. The success of any bulk mining method depends on the degree of stability maintained during the stoping operations with reference to the mining rate, the performance of the backfill with respect to the per cent extraction of pillar ore, and the control of the mine structure with respect to safety and productivity. One such method has been previously described(I) where a steeply dipping orebody is being mined with a sub-level method that employs large, hydraulically placed tailings pours for delayed pillar recovery. The paper describes the rock mechanics analysis undertaken to establish the stope and pillar geometry and the approach taken to establish backfill strength requirements to prevent dilution during pillar recovery. Production with this method started in 1970 and because few, if any, large bulk pours had previously been used in- this way (judging by the lack of information in the literature), design data and criteria were needed for several aspects of the work. Methods to establish backfill quantities and pertinent ""in-place"" fill properties are described in 2, 3 and 4 in the list of references. Results of field measurements taken to establish fill pressures for bulkhead design purposes are described in 5 and 6. Laboratory large-scale model tests undertaken to confirm a fill strength design equation, which takes into account fill arching, have recently been completed. A paper describing these tests and the results will be forthcoming in the near future."

Jan 1, 1982

By C. Pichler, S. Luidold, C. Wagner, C. Sagadin, D. Kreuzer

Engineers and scientists have been combating the attack upon refractory materials of molten metals/matte and slags for hundreds of years. The details in many cases are still questionable or at least debatable. The corrosion is a major concern for furnace operators as refractory wear or failures inevitably results in reduced production efficiency and furnace reliability. Also the cost to industry is considerable and only a thorough understanding of all the complexities of the process will help to minimize that cost. One of the critical questions to overcome is the correct selection of refractories for the individual process steps to provide long and predictable refractory life together with high furnace availability. To understand the nature of the reactions involved in refractory corrosion, it is crucial to determine the complex thermo- chemical equilibria of the reactions occurring between the refractory materials and the process phases. A simulation model coupled with commercial software like FactSageTM is demonstrated aiming to understand the corrosion mechanisms between refractories and the molten process phases and draw implications for improving the performance of refractories and refractory lifetime. INTRODUCTION The extraction or recycling of valuable materials, e.g. metals, can be done by two main routes, pyro- and/or hydrometallurgical processing, depending on the chemical behavior of the used ore, scrap or pre-treated concentrate. Sometimes it is also necessary to use both process routes for the extraction or the recycling of valuable materials. In the case of a pyrometallurgical treatment, the usage of refractory materials is inevitable. This is mainly caused by high temperatures, prevailing during processing. The interaction between refractory material and slag, metal or matte leads to different reactions and interactions. As a main result corrosion of the furnace lining (refractory material) takes place. Hence, recurring furnace shutdowns occur for renewing the refractories. This leads to reduced production efficiency. Such refractory lifetimes are between some hours and decades, depending on the processes.

Jan 1, 2019

The cost benefits of controlling dilution of extracted ore have been very well understood by miners and mining professionals for many years. However, as we strive towards more mechanization, the dilution factor has been compromised in order to fit ?equipment? that is better suited to provide improved safety and productivity. Alternately, the drilling and ground support is accomplished by handheld drilling. In 2007, a short study, commissioned by CAMIRO (Canadian Mining Industry Research Organization) on the safety of hand held drilling vs. mechanized drilling, concluded that the risk of injury with handheld drills was seven times greater than with mechanized drills. Armed with this data, MEDATech Engineering proposed to the CAMIRO group to fund development of a ?MICRO Bolter?.

May 1, 2009

By William D. Swank, Prabhat K. Tripathy, Tedd E. Lister, Eric S. Peterson, Delon C. Haggerd

More than half of the primary neodymium, produced directly from ores, is being used to manufacture neo magnets. Neodymium, being a critical element in supply, has attracted considerable interest worldwide to recover this metal from a variety of waste streams. From among different recycling processes, hydriding-dehydriding can prove to be highly effective in recycling discarded neo magnets present in consumer electronics. In the present study, manually removed magnets from discarded Hard Disk Drives (HDDs) were subjected to the hydriding-dehydriding process in order to evaluate the resultant products for the re-fabrication of the magnets. The paper describes the effect of experimental parameters on both the hydriding and dehydriding processes as applied to different magnet chemistries.

Jan 1, 2014

By Michel Chouteau

"A very conductive zone was revealed in 1977 and 1978 by magnetotelluric (MT) measurements carried out near Ste-Mathilde, 6 km northeast of La Malbaie . In order to identify the structure causing the anomaly, thirty-five MT soundings were recorded in 1980 and 1981 on and around the conductor within a radius of4 km. Results confirmed that the conductor is of limited extent (less than 2 km by 0.4 km). The proposed model is a highly conductive vertical slab, the top of which is within 200 m from the surface. At a depth of approximately 825 m this structure joins a conductive layer which extends to the northwest but not to the southeast. The large conductivities and the depths involved can only be explain ed by a fractured zone flooded with electrolytic solutions, by graphite veins or by metallic mineralization (sulphides). The former seems to be the most likely hypothesis because an EW fault running across this zone could have allowed percolation of water and the leaching of disseminated pyrite out of a mylolisthenite filling the fault.IntroductionLa Malbaie is located 130 km northeast of Quebec City on th e North Shore o f the St. Lawrence River (Fig. I). Four major groups o f rocks have been mapped in this area: charnockitic rocks to the west , granitic rocks in the north east and southeast, gneiss and pegmatites northwest and south of La Malbaie , and Paleozoic sediments in the Clermont-La Malbaie Valley and along the shore of the St. Lawrence River (Rondot, 1966). Two major features dominate the structure of the region: Logan ' s line , a major thrust fault beneath the St. Lawrence which separates the Grenville Province to the north from the Appalachian regime to the south, and the Charlevoix Crater , a large Paleozoic impact crater that created an almost perfect annula r structure centred on Mont des Eboulements (Rondot, 1970). Ste-Mathilde is a village lying 6 km northeast of La Malbaie, just outside the ring-like graben zone caused by readjustments after meteorite impact. The survey area spreads over a granite body which is more than 2 km long and 0.6 km wide, surrounded by a wide migmatite zone which is injected by many bodies of pegmatite, the latter likely related to the granite body (Fig. 2). A zone of leptynites lies west of the area. An east-west trending fault (FA1) related to the Charlevoix Crater runs mid -way across the survey area; a second parallel fault (FA2) south of FAI separates the gneissic rocks from the Paleozoic sediments. The overburden is usually thin with outcrops frequently encountered except for the centre of the survey are a where 10 m of glacial sediments are expected (E. Gaucher, 1982, personal communication)."

Jan 1, 1985

By Todd Kennedy, Kurt Tischler

"This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry … We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues. INTRODUCTIONThe first Siemens Gearless Drive in mining began operation in 1980 and was installed on an iron ore grinding mill. As of September 2011, 40 Siemens Gearless Drives will have accumulated 136,000 machine days of operating time. According to pure rules of statistical analysis, this accumulated operating time may be too low to be used for a sample of field data to provide precise statistical values of availability, however we consider it large enough to provide indicative values of worthwhile consideration. This paper deduces the availability statistics of Siemens Gearless Drives in the mining industry from information received from end users and factors in all major issues that Siemens has experienced with our Gearless Mill drives. This paper does not consider Gearless Drives in other industries such as the cement industry. The cement plants, especially in the northern hemisphere, interrupt production for several months in the winter. This lengthy downtime is used to maintain the complete plant including the mills, their motors and their drives. The mining industry has more stringent and higher production requirements. In the mining industry, production must run 24 hours per day, 365 days a year."

Jan 1, 2012

By E. Topuz, C. Duan

"INTRODUCTIONOperations research (OR) applications have experienced a substantial growth within the mining industry during the last three decades. The purpose of this paper is to present a summary of the results of a comprehensive survey of the application of various OR techniques to the major mining activities. It is hoped. through this sur vey , that the most widely used OR approaches, the important areas of application, and future trends have been identified.This survey included more than 500 articles published in this field in English since the late 1950s. Most of the relevant literature was found in mining publications, but, in terms of quality and originality, important applications were also found in literature not related to the mining industry. The sources constituted periodicals, proceedings research reports, and a few books. A listing of selected publications from which three or more articles reviewed in this survey appear is given at the end. Operations Research MethodologiesOperations research is concerned with optimal decision making in, and modeling of, deterministic and probabilistic systems that originate in real-life situation s. One basic feature of the OR methodologies is the attempt to optimize certain design parameters, subject to a set of constraints. This distinction has been employed in the survey as a guideline for selection of the techniques covered under the title "" OR methodologies"". The methodologies thus encountered in the literature are listed below. In a few cases, simulation has not been considered because it is not an optimization method per se."

Jan 1, 1989

By J. C. Farge, G. G. Jacox

"The effect of composition and process variables on the properties of Marmet and modified Ni-Hard slugs will be discussed. The effect of shape on the over-all performance of grinding media and its relationship to the end product has been investigated and these results will be reviewed. The cost effectiveness of slugs versus balls has been well documented under various operating conditions and this will be presented in detail. IntroductionThe selection of grinding media is based on the cost-to-wear ratio combined with the consideration that it must stand repeated impacts without breaking. The specific consumption of grinding balls and slugs depend s primarily on their microstructure, which, in turn, is controlled by chemical composition and by the processing condition s to which they are subjected during manufacture.The first part of the paper deals with the optimization of alloy content to produce cast iron slugs with microstructures consisting essentially of marten site and carbide and with hardnesses of 650 B.H.N. and higher. The second part deals with the use of cast iron slugs to replace forged steel balls in milling operations. Tests indicate that the shape of the media has little if any effect on results and that the hardness and microstructure of grinding media will determine its relative performance. Where price is equal under similar milling conditions, the cost effectiveness of cast iron slugs is superior to that of forged steel balls.In order to understand the role of alloying elements in cast irons, it is judicious to consider the microstructural changes which occur during solidification and subsequent cooling, particularly from above the eutectoid temperature. Solidification starts with the formation and growth of dendrites of austenite. As temperature decreases, an eutectic nucleates and grows between the primary austenite dendrites. Immediately after solidification, the structure consists of proeutectic austenite and of the eutectic of primary carbides and austenite. On cooling to room temperature, austenite can be retained or transformed to pearlite, bainite, martensite or mixtures thereof. It is necessary to prevent decomposition of austenite into pearlite by adjusting the alloy content. For best abrasion resistance, the microstructure at room temperature should consist essentially of martensite and carbide. These types of irons are known as ""martensitic irons "". Depending on the carbon content of the austenite and cooling rate, "" as-cast"" martensitic irons will contain different proportions of martensite and retained austenite. The more carbon in solution in the austenite, the lower is the temperature at which the martensitic transfoemation takes place. By the time room temperature is reached ., the transformation is seldom complete, and the end product is generally a mixture of martensite and retained austenite."

Jan 1, 1980

By M. J. Merwin

Heat treated seamless tubular products are processed in a fashion that can be easily modified to produce dual phase microstructures, through the implementation of intercritical soaking prior to quenching. Dual phase steels are known to possess low yield strength compared to tensile strength. The steel line pipe market is interested in low yield-tensile ratio materials for application in reel barge pipe laying operations. In the current work compositions of commercially produced material already in use for the line pipe market were examined and dual phase microstructures were successfully developed. The microstructure and properties of the materials were found to be stable over the range of intercritical temperatures employed. Tempering temperature and, somewhat unexpectedly, small chemistry differences were found to have the largest influence on properties. Excellent toughness performance was observed in samples tempered at temperatures in excess of 550°C. Tempering in this temperature regime produced materials with strength suitable for application as API X60 line pipe. A difference in tensile strength between steels of similar chemistry was observed, and is not fully understood at this time. Welding performance was considered through simulation of three regions of the heat-affected zone. Neither intercritical temperature, nor tempering temperature, were found to have a significant influence on the heat-affected zone properties. The peak temperature achieved in the thermal cycle was the only significant factor. The hardness of the heat-affected zone was found to increase continuously with increasing peak temperature. While toughness was found to be low for both partially-transformed and coarse-grain heat-affected zones, the toughness of the fine-grained heat-affected zone was substantially better. Based on the results found in this laboratory study, a limited production trial is expected.

Jan 1, 2005

By A. B. Morrow

Consulting engineers are well aware of large variations in plant operating cultures between countries, companies, and even within sites and operating crews. These operating cultures must be considered when designing Advanced Process Control (APC) applications in order to maximize utilization rates and return on investment. Designs must be driven by an understanding of the totality of unit operations. Economic factors, equipment constraints, management philosophy, maintenance department responsiveness, instrumentation reliability, operating crew skills and teamwork, and individual operator concerns are all important and must be considered during application design. A general approach to incorporating operating culture considerations into APC application design is described. A case study for an iron ore concentrator plant is presented.

Jan 1, 2014

By N. Ahern, M. Barbanell

Mercury is often present in gold ores and can be released during processing. In view of health and environmental concerns related to mercury, the mining industry takes leadership in the responsible management of mercury. This paper reviews various aspects of mercury management, including an overview of mercury deportment in typical gold processing flowsheets; trends in mercury legislation impacting the international flow and management of mercury in the gold mining industry; and treatment, storage and disposal options for mercury and mercury containing materials.

Jan 1, 2014