Search Documents

By Owen Owens, W. P. Armstrong

Abstract- The process of arriving at the size and grade of: (a) a newly-discovered body of mineralization, (b) a potential ore resource, (c) an orebody proposed for mining, or (d) the ore reserves in a mine, requires fundamental geological, and geometrical determinations as well as physical and chemical analyses. This paper outlines geological and geometrical features considered critical, in the authors' experience, in realistic reserve determination. These are discussed under the headings "The Four Cs". They include the Character, type or nature of the mineralization; the Continuity of various types of mineralization in the deposit; various key concerns in the Calculation besides the mathematics; and the Classification section which refers to basic considerations in classifying a mineral estimate. It is suggested that the responsibility for the calculation of a Resource or Reserve should be that of a geologist experienced in the ore type under review. Further, it should be the responsibility of the board of directors of the company owning the deposit to ensure that a sufficiently experienced person is chosen to carry out the process.

Jan 1, 1993

By CIM Mineral Resource

On January 9, 2018, the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Council formed the CIM Mineral Resources and Mineral Reserves Committee (CIM MRMR Committee), which is a combination of the previous Standing Committee on Reserve Definitions and the Best Practices Committee. As part of its mandate, the CIM MRMR Committee updates guidelines for use by Industry, which include the Uranium Practice Guidelines. The 2024 CIM Uranium Leading Practice Guidelines were adopted by CIM Council on November 22, 2024, and supersedes the 2003 version. The main principles and guidelines relating to preparation of Mineral Resource and Mineral Reserve (MRMR) estimates are provided in the CIM Estimation of Mineral Resources and Mineral Reserves Best Practices Guidelines (MRMR BP Guidelines, as updated from time to time). The MRMR BP Guidelines provide information pertaining to metalliferous and other deposits and many sections are readily applicable to the preparation of MRMR estimates for uranium deposits. However, additional guidance is appropriate for uranium deposits due to the radioactive nature of uranium, and its amenability, in some cases, to in situ recovery (ISR) mining methods.

Nov 1, 2024

By J. J. Jonas, G. R. Stewart, A. M. Elwazri

Two important parameters for dynamic recrystallization can be derived from the changes in the strain hardening rate: the critical strain for initiation of dynamic recrystallization and the point of maximum softening. In this work, these values are determined from the flow stress-strain data obtained in continuous compression testing in the range 900-1100°C. The resulting strains are used to calculate a kinetic model of dynamic recrystallization for two materials: 304 austenitic stainless steel and a hypereutectoid plain carbon steel. The mechanical parameters used to define the proposed model are confirmed with quantitative metallographic analysis of the recrystallized microstructure.

Jan 1, 2004

By N. E. Nelson

"The Hidden Creek mine is about l~ miles north of the north end of Granby bay; a nearly landlocked body of water on the west side of Observatory inlet; 90 miles north of Prince Rupert; British Columbia.The main haulage way of the mine at 385 feet above sea-level has been driven north into the somewhat precipitous end of a north-south ridge that rises from the tide flats between the east and west forks of Hidden creek. The outcrops of the principal orebodies, two prominent bluffs of stained rocks and sulphides, were higher on the face of the ridge and extended from about 530 to 850 feet elevation. North from the bluff tops, the ridge comb rose gradually to about 1,200 feet elevation. The name of the discoverer and the date of discovery of the Hidden Creek orebodies are probably unknown, but the discoverer is believed to have been an Indian from one of the reservations along Observatory inlet. The deposit was brought to the attention of John Flewin, Government Agent at Post Simpson, near the beginning of the present century. Mr. M. K. Rodgers, developer of the Nickel Plate mine at Hedley, did the first organized work on the deposits. Next the Hidden Creek Copper Company prospected the property. Rodgers acquired the prospect a second time, did more work, and finally in 1910 optioned the property to the Granby Consolidated Mining, Smelting and Power Company, Limited, at that time operating at Phoenix and Grand Forks in the Boundary district of British Columbia. The optionees stepped up the development work and brought the property to production in 1914. The ores were direct smelted until 1924. In that year a mill was built. From 1930 until the end of the productive life of the properties in 1935, all of the ore was milled and the concentrate smelted. From March 17, 1914, until July 31, 1935, the production from the Hidden Creek mine was, in round numbers, 18,000,000 tons of 1.70 per cent copper ore and 6,000,000 tons of low grade dilution rock. The Hidden Creek mine ""died with its boots on"". During 1934 the average monthly production was 146,377 tons of 1.06 per cent copper ore. For 7 months of 1935 the average was 161,750 tons of 1.03 per cent ore, and for the final month, July 1935, the production was 156,950 tons."

Jan 1, 1954

By L. Jones, S. R. Lawrence, A. R. Holloway

Whilst dense medium separation is best known for its ability to concentrate diamond and coal deposits, the process is now being employed in southern Africa as a pre-concentration step to improve the economics of platinum group metal and nickel ores. DMS plants built for these industries (such as the 1600tph unit at Tati Nickel, Botswana), are spearheading an expansion in this area by reducing mine and process operating costs yet maintaining economic metal recoveries. This paper provides an overview of DMS technology and examines the economic benefits available to North American operators and projects, with recent case studies as reference.

Jan 1, 2009

By Gerald S. Cole

It used to be that a science/engineering presentation on "light weight" at a metallurgy conference, would relate to the materials science, processing, component fabrication and applications of aluminum, magnesium and titanium. Within the automotive industry, light weight now includes how to "lighten up", how to lightweight, or how to mass reduce vehicle components and systems. Increasingly stringent global emissions-reduction requirements require increasing vehicle fuel efficiency; mass reduction is an enabler to achieve this. While light metals certainly are the basis, a host of other materials can be used to optimize mass reduction while meeting vehicle performance, safety and cost requirements. New grades of ultrahigh strength steels and even nanosteels can be thinned down and save over 1/3 the mass vs conventional mild steels. A compacted graphite cast iron engine can be made lighter than an aluminum one. Aluminum components in vehicles were only castings; now aluminum stampings, forgings and extrusions are becoming more visible components of mass reduction. Lower mass high temperature polymers, and carbon fiber polymer composites now replace aluminum and steel. These materials often require specialized processing and manufacturing techniques to produce a component, including superplastically formed twin roll cast sheet aluminum and magnesium, and hot stamped/in-mold quenched steels. The assembly of hybrid structures requires unique joining/bonding, and corrosion-inhibiting techniques that might include sophisticated structural adhesives. This thinking "light" presentation, will conclude with a discussion of U.S. and Canadian government engineering and research support for mass reduction, including the proposed $148 M American Lightweight Materials Manufacturing Innovation Institute.

Jan 1, 2014

By David Thomas, Charles Harper, Brian Watters

The Star-Waddy Lakes area lies withjn the northeasterly-trending early- to mjd-Proterozoic volcanoseilimentary-pl utoruc belt referred to as the La Range Domllin. In the area investigated the domajn is composed of the Central Metavolcaruc Belt which is bordered by metasedimentary belts of the Crew Lake and MacLean Lake Belts to the northwest and southeast respectively. The boundaries between the Central Metavolcanic Belt and the flanking belts are generally marked by prominent zones of shearing. The volcanosed imentary succession is intruded by a variety of ultramafic to felsic plutons which, on the basis of lithology, field relations and geochronology, can be broadly subdivided into three groups or episodes. These are: a) an 'early' (ea. 1866 Ma), possibly subvolcanic, episode marked by composite intrusions ranging from gabbro-diorite to granite, b) an 'intermediate' (ea. 1854 Ma) plutonic event distinguished by more homogeneous felsic intru ions ; and c) a 'later' (ea. 1835 Ma) event characterized by leucocratic quartz-rich grani te intrusions. The La Range Domain has undergone polyphase deformation with a strongly developed northeast-trending structural grain. Large scale folding is manjfested by large regional sy nforms, arcuate and triangular patterns associated with many of the plutons and by tight to isoclinal folds within the adjacent metasedimentary belts. Inhomogeneous strain characterizes much of the Star-Waddy Lakes area. With strain gradients being typically very steep, zones of high strain consisting of zones of extreme extensional fabrics, discrete shearing, as well as broader zones of cataclasis and structural slicing, are often juxtaposed with areas of relatively minimal deformation . Dilation structures tend to favour these zones of highly contrasting strain. Late, brittle fractures, faults and shear zones are widespread and appear to be particularly important as loci for gold mineralization. Metan1orphic mineral assemblages indicate that upper greenschist to middle amphibolite facies conditions were attained. Geological and geochenucal evidence indicates that the Central Metavolcanic Belt evolved in an island arc environment. Metavolcanic rocks from both the Waddy and Star Lakes areas display similar characteristics on variation diagrams (e.g. AFM and the Jensen cation plot) in that the dominant trend is calc-alkaline with some basic to intermediate types having a mildly tholeiitic character. A few samples from the southern end of Lower Waddy lake display komatiitic to basaltic-komatiitic afl'injties. The relatively immobile minor and trace elements (e.g. Ti , Zr, Nb, Y, Cr) provide reliable characterization of the metavolcanics, particularly of the basalts, which have highly distinctive trace element properties. Geochemical patterns for the basalts are similar to those for modem volcanic arc basalts. Low initial 87Sr/86Sr ratios (0.7017 - 0.7019) are consistent with a subduction-related origin for the volcanics. The major plutons have chemical properties typical of volcanic arc granites and are largely calc-alkaline in character, showing little chemical variation from the volcanics.

Jan 1, 1986

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016

RÉSUMÉ L’estimation la plus précise possible des coûts de minage est d’extrême importance pour les études de préfaisabilité afin de diminuer les risques financiers des projets miniers. Les méthodologies existantes d’évaluation des coûts de minage ne permettent pas de les évaluer avec des marges d’erreur acceptables tout au long de l’évolution des projets miniers. Elles visent à évaluer les coûts unitaires de minage des études préliminaires de faisabilité, pour les principales méthodes d’exploitation, en prenant pour l’hypothèse que ces coûts dépendent principalement du taux d’extraction journalière. Si cette hypothèse peut être justifiée pour l’évaluation du coût d’opération, elle est fort discutable pour l’évaluation des coûts de minage. Pour démontrer que cette hypothèse est inadéquate nous avons analysé la méthode d’exploitation la plus populaire sur le continent nord-américain c’est à dire celle par chambres vides avec retrait horizontal (Hr – Horizontal retreat), ou « Longhole » et celle avec retrait vertical (VCr - Vertical Crater retreat). Il ressort de cette analyse que les coûts unitaires de minage dépendent principalement des conditions géotechniques du massif rocheux et de la largeur du gisement et non pas du taux d’extraction journalière du minerai.

Jan 1, 2010

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

By Norman J. Tienkaivip, Christopher J. Preston

"This paper describes the use of electronics for physical measurement and computer analysis in both open-pit and underground mining operations for the ultimate purpose of optimizing production blasts. Techniques in monitoring single borehole blasts using both pressure and vibration sensors to establish in-situ dynamic rock properties are outlined, including characterization of multiple borehole production blasts with regard to stress generation.Once field derived measurements are computer analyzed, they are channelled as input parallel to other data, such as the explosives thermochemical performance properties generated by a sophisticated computer program called ""HT-65"" into BLASPA . BLASPA, a blast simulation computer program, then couples these input with a mathematical model which defines the blasting processes. Aspects such as the blast geometry, explosive loads and distribution, hook-up, and costs are studied. The final output table gives specific blast performance or quality factors for each blast procedure. These results are then easily compared and rapidly optimized to achieve maximum performance at lowest blasting and drilling cost."

Jan 1, 1984

By W. J. Kempson

In recent years, substantial progress has been made with respect to the definition and control of the primary energy requirements in underground mines. Little has, however been done to develop a more detailed understanding of how to limit the various pressure losses which are intrinsic to shaft systems. This is in spite of the fact that more than half of the pressures generated by the ventilation fans in deep level mines are dissipated as pressure losses within the shaft system. This paper presents research which has been completed to optimise the pressure losses which occur in shaft systems as a result of the ventilation air flowing through them. In this regard, the response of various shafts to the ventilation air flowing through them was measured. These results were evaluated against the current theory for the calculation of shaft pressure losses. Finally the results of the measurements and calculations were used to calibrate a Computational Fluid Dynamics model of the shaft systems. This model was then iterated to allow meaningful conclusions as to the specific make up of the shaft equipment which contributes the most to pressure losses in shaft The results of the above analysis demonstrated that the current theory used for the evaluation of these pressure losses is deficient. The paper discusses these conclusions and the specific ramifications of the analysis. Finally, the understandings gained with regards to the above research are applied to the design and layout of equipment in mine shafts. In this regard, the shape and orientation of the shaft steelwork is evaluated and it specific interaction with the piping and conveyance is evaluated. Coming out of this evaluation are specific recommendations for the design of future shaft systems. These recommendations are based on the above models and offer specific savings on the lifetime operating costs of shaft systems.

Aug 1, 2013

By R. J. Labine, D. I. Brisbin, R. Roussain, P. R. Coad

"Abstract - The Owl Creek Mine is located near the west end of the Neo-archean Abitibi greenstone belt, 17 km northeast of Timmins, Ontario, and 4 km north of the Destor Porcupine fault. Gold occurs in epigenetic quartz veins and their pyritic wallrocks in two zones within a package of east striking, steeply north dipping, volcanic and sedimentary rocks. At the West Zone, 1 729 603 t of ore with a grade of 4.83 g/t Au (268 587 troy oz.) were produced from an open pit centered on a wedgeshaped unit of Tisdale Group basalt that occurs between two overturned, south facing units of Porcupine Group graywacke and argillite. Basalt/graywacke contacts are locally marked by graphiticcarbonaceous argillite, strike-parallel faults and massive quartz veins.Deformed quartz+/-ankerite veins occur along the graphitic sedimentary/volcanic contacts and in gently to moderately dipping fractures in basalts, and, to a lesser extent, in graywackes. Veins also occur sub-parallel to steeply dipping 070° foliation. Altered host basalts are composed of iron carbonate, sericite, quartz, carbon, chlorite and disseminated pyrite. Gold occurs as inclusions in pyrite, and less commonly as free gold in fractures and along graphite-quartz grain boundaries in quartz veins. Fractures preferentially developed in more competent basalts during pre- to syn-ore deformation are interpreted to have provided the permeability required for emplacement of mineralized quartz veins. Carbonaceous basalt/graywacke contacts further enhanced gold deposition by acting as chemical traps. The interaction of hydrothermal fluids with these carbonaceous sedimentary rocks led to the characteristic local darkening of host basalts due to carbon impregnation and chlorite development."

Jan 1, 1998

By C. Campero, C. Nicolau, L. Pagliero

The Chilean Congress has recently promoted desalination as a solution to meet the mining industry’s growing water demand. However, this rapid expansion of desalination infrastructure comes with trade-offs. This includes a significant energy cost for treatment, as well as socio-environmental impacts on indigenous communities, tourism, fisheries, and the marine ecosystem. This paper advances a regional-scale model for analyzing competing trade-offs through a case study in the Antofagasta mining region of Chile. Through geospatial data analysis in ArcGIS, new desalination infrastructure investments supplying water to mines are overlain with features of concern raised by communities during the environmental impact assessment (EIA) process, such as national parks, fisheries and exploitation areas for benthonic resources. The resultant model provides a test-bed for analyzing the cumulative effects associated with desalination expansion and for investigating scenarios to mitigate negative social-environmental impacts. The model simulates alternative scenarios for desalination locations and pipeline routes according to competing constraints (i.e. to minimize cost and energy constraints while also avoiding ecological and social hotspots). The ultimate contribution of the work is a demonstration of how the proactive adoption of a regional-scale infrastructure planning might have led to different desalination investment decisions. INTRODUCTION Chile represents the largest producer of copper globally, and holds approximately a third of the world’s estimated copper reserves. However, access to water represents a major constraint to industry expansion and creates conflicts with competing water users (Aitken et al., 2016; Côte et al., 2010). Recently, the Chilean Congress has promoted desalination as a solution to meeting the industry’s growing water demand, which is likely to lead to significant growth in desalination infrastructure to support large-scale mining projects that extract freshwater over a rate of 150 l/s1. By most recent projections, the Chilean copper mining sector is set to increase seawater use by 230% by 2029 (Faversham House Group Ltd, 2019). By the year 2015, Chile had 11 projects serving the mining industry and there are at least other 12 planned plants (Cochilco, 2015). While the use of seawater allows continued expansion of the sector without depletion of scarce underground aquifers, it is nonetheless accompanied with important socio-environmental drawbacks. One such challenge with desalination is the associated energy costs, expressed, both economic and environmental (e.g., CO2 emissions). This includes the energy required for reverse osmosis treatment facilities, as well as to pump water to inland regions at high elevations around 3.100 m.a.s.l in Chile. (Dixon, 2013; Knops et al., 2013). Additionally, the impacts of desalinated water use on flotation chemistry are generally poorly understood, necessitating the need for further research into the impacts, both positive and negative (Cisternas and Gálvez, 2018; Liu et al., 2011).

Jan 1, 2019

By T. S. Golosinski

"This paper reviews the types of selective continuous miners (SCMs) available at present, and compares their main features. Furthermore, operating practices and mine planning aspects of the SCMs applications are reviewed and conditions for efficient application of this equipment are defined. Finally, the potential applications of the SCMs in surf ace mining of oil sands are discussed INTRODUCTIONIn the 1970s the United States Bureau of Mines (USBM) conducted a program of investigations, design and demonstration of various continuous surface mining concepts, This included continuous mining equipment which was an adaptation of several civil engineering and/or underground mining machinery concepts to surface mining. Upon termination of this program, the related development was continued by a number of equipment manufacturers, leading to development of several types of SCMs. This new type of surface mining equipment is able to mine selectively hard and thin multi-layered formations at high, sustained, and economically viable production rates.While used mostly in coal mining at present, the characteristic features of this equipment permit conclusion that it may prove to be an efficient tool for surface mining of oil sand, and/or related overburden stripping. Of particular interest here may be the ability to mine thin layers of hard material, without a need for its earlier fragmentation, and the ability of the SCMs to load a variety of haulage equipment, including belt conveyors."

Jan 1, 1989

By Jean Descarreaux

"The Rexspar uranium deposits are located near Birch Island in central British Columbia. The property lies within the Omineca crystalline belt of the Cordilleran Orogen. Gneiss, schist, tuffaceous and porphyritic trachyte are the main rock types encountered on the property. These rocks are of pre-Late Triassic or probable Mississippian age.Lenticular bodies of mica and pyrite-rich rock are the host of three closely spaced uranium deposits and are found close to a fluorite deposit. The altered trachytic rock as well as the fluorite and uranium deposits are found in the upper part of the trachyte unit. The latest tonnage estimates are 1,441,820 tonnes averaging 23.46% CaF, for the fluorite deposit, 490,966 tonnes of 0.084% U10afor the 'W' deposit, 164,290 tonnes of 0.074% UP8 for the ""B"" deposit and 459,124 tonnes of 0. 071 o/o UP8 for the ""BD"" deposit.A hydrothermal replacement origin was first proposed for the fluorite and uranium deposits. The mineralizing and altering solutions would have been genetically related to a felsic batholith outcropping a few kilometres south of the property. Another hypothesis has been proposed more recently. A volcanic centre has been tentatively identified in the upper part of the trachyte unit, close to the mineral deposits. The fluorite and uranium deposits could possibly be volcanogenic, rather than related to the Cretaceous felsic batholith.IntroductionFluorite and uranium mineralization occur on the property of Consolidated Rexspar Minerals and Chemicals Ltd. in central British Columbia. The exploration and development works executed over the years are summarized in this paper. The deposits and their geological environment are described but the origin of the mineralization has not been definitely established."

Jan 1, 1986

By G. Girard, A. Larouche, J. Colbert, G. Doyer

"The Direct Chill (DC) casting process uses water to extract heat from molten aluminium and helps to control the solidification process. Many factors such as the water flowrate, water distribution around the mould and water impingement angle have significant impacts on the solidification process. It has been noted that the chemistry variation of the cooling water is also an important factor that has a major impact on the presence of defects on the ingot. A significant change in the water quality can produce defects on the ingots such as cracks, bleedouts, or runouts. Understanding the impact of water quality variation on ingots is therefore essential to ensure good ingot production and reduce defects. This paper aims at describing a new approach to follow the variations of process water quality over time. It is an original and innovative method, which is still under progress. A water quality and stability index (WQSI) is under development to evaluate changes in the water composition based on water physico-chemical parameters. The index is calculated by comparing each of the actual parameters with historical values previously modeled by a statistical law. It is a dimensionless number having an adjustable weight factor for each parameter. The positive or negative contribution of each parameter, with respect to the water cooling capacity, is taken into account to calculate the WQSI. The current selection of parameters is based on knowledge from the literature as well as on empirical experience. When the developed tool will be mature, it could be used to track water variations upon time and anticipate problems, enabling proactive actions to ensure good ingot production.INTRODUCTIONFor many years, the impact of water chemistry on heat transfer, during DC casting, has been of great interest in the aluminum industry. Several papers have been published to demonstrate the correlation between water chemistry and heat transfer (Yu, 1985), (Gildemeister, 2014). Although numerous studies do present the effects of water parameters (i. e. hardness, conductivity, oil, and grease…) on cooling capacity under controlled experimental conditions, they do not reflect the strong interactions between the parameters and variations present in a casting center. Wells and Cockcroft also demonstrated that laboratory based studies are not fully representative of real heat transfer in an industrial casthouse, there are too many factors involved (Wells, Li, & Cockcroft, 2001). In this context, it becomes very difficult to obtain a quantifiable relationship between the capacity of water to cool the ingot and ultimately the performance of the cast."

Jan 1, 2016

By L. R. Bower

"This paper describes a highly versatile variable speed unit with a torque multiplication feature as a direct replacement for a fluid coupling .The unit is comprised of a modulating clutch with torque converter and lock-up options.The UCD does not start or stop the motor. This is carried out in the normal manner.The UCD continually monitors and rapidly regulates the output speed to the requirement of a set point demand from input signals or a pre-set program with full manual override.The pre-set program can include start and stop ramps, top speed and minimum speed regulation and also mid-speed set point with security for man-riding, etc. Speed variation is from zero to 100% on a constant duty basis.The input signals can be from any source, e.g. belt weigher. load profile bunker probes, mine monitoring system, etc.The UCD when fitted with a torque converter has a torque multiplication feature which automatically provides a starting torque up to two and a half times greater than the full load torque without exceeding the normal motor power levels.IntroductionIt is common practice in the mining industry to drive conveyors, whether they be belt or chain, through a transmission system incorporating a fluid coupling between the driving motor and gear-box .However, there are drawbacks and in an effort to attain a better degree of drive and control, two-speed motors - inverters cycle- converters - hydrostatic drives, etc ., have been introduced."

Jan 1, 1986

By R. Edinger

Aerospace and space products depend, probably more than any other products in industry, on advanced materials. While there are many ways of producing aerospace parts, in many cases the process does not allow the design of the metallurgical properties according to the part or product requirements in accordance with its mechanical configuration. Key to the next level of innovative manufacturing is the capability to control the amount of energy applied to the process, as well as the addition of materials in form of vapor or solid particles such as powder in order to build up the metallurgical composition required. With the development of a high speed pulsed laser-electron beam source, the LASTRON(TM) technology, we deliver the basic requirement for a digital manufacturing process of aerospace and space products. This technology, combining Laser and electron beam, finds application in welding, drilling-machining, and is currently modified to allow digital coating (PEB-PVD) methods. In addition to the coating, a powder metallurgical process, called Rapid Manufacturing (RM), will allow the precision melting of parts based on CAD/CAM files. The RM process and the digital coating will allow the production of graded aerospace alloys in parts for jet engines and aero-structures.

Jan 1, 2006

By M. Noaparast, N. Nickoletopoulos, André R. Laplante

"This paper presents an application of the use of synthetic ores to study gold recovery by gravity. Three case studies are presented: the first focuses on the use of tungsten to study applications of Knelson Concentrators for upgrading gravity concentrates; the second on tungsten again, in this case to study the performance of a 86 Falcon Concentrator; and the third on lead to mimic gold's grinding behaviour.It is shown that the use of synthetic ores with metallic substitute for gold is not only expedient, but it can also lead to an increased understanding of separation and grinding mechanisms, because of the more accurate results and controlled particle shapes. The case studies highlight the problems associated with gold particle flakiness and gangue density. The grinding behaviour of malleable materials is shown to be complex, as particles can migrate to coarser size classes by flattening and cold welding, and to finer size classes by folding and actual breakage.IntroductionThe title of this contribution is not entirely misleading. Mineral processing has much to do with philosophy, rather Philosophy, as described by Georgius Agricola:""Furthermore, there are many arts and sciences of which the miner should not be ignorant. First there is Philosophy, that he may discern the origin, cause, and nature of subterranean things; for then he will be able to dig out the veins easily and advantageously, and to obtain more abundant results from his mining. ""1"

Jan 1, 1995