Search Documents

By David O. DeGagné

While mine backfill plants are becoming increasingly more automated and instrumented, especially with paste fill operations, underground backfill distribution systems have hardly changed over the years. While fill properties are appropriately measured in the preparation plants, as backfill enters the mine borehole, the technology for control, data gathering and reporting is somewhat lacking. Mines typically experience problems with borehole and pipeline plugging, pipeline bursting, bulkhead failure and exposed fill sloughing. With adequate instrumentation of the backfill system it is possible to obtain a complete, continuous and detailed picture of the entire filling operation from preparation to post-pour. Good data will, over time, provide the basis for needed improvements of backfill systems and will be essential to safer, more efficient and less costly fill practices. This paper will review the areas of the filling operations where monitoring would prove critical to eliminate failures such as pipelines, bulkheads, fill exposures, stope walls, etc. The types of monitoring systems currently available will be reviewed and potential areas for development will be highlighted.

May 1, 2001

By Peter White

Mine Planning Shaft Collar Shaft Sinking Raises Ramp Underground Water Storage

May 1, 2009

"The Ernest Henry Mining (EHM) ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite. At the end of 2009, EHM converted the ball mill media charge from forged steel to high chrome media. At high pH values (above 10.5), forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response. Given this, the pH in the roughers was dropped from 10.6 to 9.6 and it was found that there was a slight increase in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold. With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.INTRODUCTION The Xstrata Copper Ernest Henry Mine (EHM) is situated 38 km north east of Cloncurry, Australia. The mine began as an open-cut operation in 1998 and transitioned to a multi-sourced operation in December of 2011, utilising ore from the newly completed underground mine in addition to ore mined from the Mount Margaret Mining operations. EHM produces a combined copper gold concentrate containing 25 000 t of copper and 35 000 oz of gold annually, utilising a three stage grinding circuit along with a four stage flotation circuit. In addition to this EHM also produces 1 000 000 t of magnetite concentrate annually via a further grinding and three stage magnetic separation circuit. Based on metallurgical test work performed by Magotteaux between 2002 and 2008, the step to change from forged steel media to 18 percent chrome media was taken in 2009 in a bid to alter the pulp chemistry to improve the flotation performance in the plant (Greet, Kinal, Twomey, & Peatey, 2010). This plant trial resulted in: • Increased dissolved oxygen levels within the pulp, • A ball mill discharge Eh shift of 25 mV to more oxidising pulp potentials, and • An EDTA extractable iron percentage reduction. These improvements in the pulp chemistry resulted in an increase of 1.7 ± 0.6 percent in copper recovery and an increase of 2.9 ± 1.7 percent in gold recovery. As the plant trial using high chrome media was successful, the use of the media was adopted as the standard for the ball mill. This implementation opened the door for further process improvements around the flotation circuit."

Jan 1, 2014

By Hamid-Reza Manouchehri

Mining & Sustainability? A Paradox?! ? Production: gradually or exponentially increasing (giant mining) ? Ore Grades: gradually declining, ? Open Cut Mining: now widespread, likely to be sustained in the future though the long-term is hard to predict as new mineral deposits are likely to be deeper ? Waste Rock / Overburden: increasing rapidly, likely to be sustained in the future and closely linked to open cut mining, especially for coal and base metals ? Economic Resources: commonly increasing but some remain stable or gradually declining, future is linked closely to exploration, technology and economics; Increasing population, changing life style and technology development, ultimately result in sustainability in mining industry to hang in the balance and continue.

May 1, 2013

By Zorigtkhuu Davaanyam, Bern Klein, Stefan Nadolski, Amit Kumar

"The High Pressure Grinding Rolls (HPGR) is a relatively new comminution technology that has been shown to be more energy efficient compared to semi-autogeneous (SAG) mills. Full and fair consideration cannot be given to HPGR-based comminution circuits in early stage projects, because presently pilot scale testing is required for assessing and sizing; pilot scale testing requires bulk samples weighing more than one tonne. A CAMIRO research program was conducted at the University of British Columbia to develop bench scale tests that would reduce the quantity of sample required to assess HPGR.Three test procedures were developed.1. The Direct Calibration Methodology calibrates piston press test results to pilot scale test results such that piston press tests can then be used to determine the energy–size reduction relationship for a range of ore types.2. The Database Calibrated Methodology, which is similar to the Direct Calibration Methodology except that it calibrates piston press tests against a database of pilot scale and piston press tests.3. The Semi-Mechanistic Methodology was developed to use piston press test results as an input for an HPGR based energy-size reduction performance model.Through utilization of these methodologies, the energy–size reduction performance of an HPGR can be predicted with minimal sample requirement. In addition, piston press testing is far more cost effective, faster, and accessible than pilot-scale HPGR testing.IntroductionOne could argue that in the future, decisions regarding selection of comminution circuits will be made primarily on the basis of energy consumption. The following facts and predictions support the argument:"

Jan 1, 2015

By K. Yamaguchi, Sekimoto. H.

"Platinum Group Metals (PGMs) used as catalyst which reduces toxic substances in emission gas exhausted from an automobile should extensively be recycled because they are rare metals produced only at the limited regions. The recycling process is to smelt an alumina honeycomb, in which PGM is built, in molten iron with flux such as lime and silica to separate them. PGMs are concentrated in molten iron while alumina in slag.The objective of this study is to understand the factor to concentrate PGMs in liquid iron as much as possible. Fundamental research of the distribution of the PGMs between the slag and liquid iron was carried out to recover the value metals of platinum, palladium and rhodium from the three-way auto catalyst. The distribution ratios of platinum, palladium and rhodium between the Al2O3-CaO-SiO2 slag and liquid iron are from 10-6 to 10-5, and these are concentrated in comparison with slag phase by about 1 million times to the liquid iron at 1873 K. The distribution ratios of platinum between the FexO-CaO-SiO2 slag and liquid iron decrease from 0.1 to 2?10-4 with increasing the CaO content in the slag. The CaO addition to the FexO unary slag is effective in concentrating platinum in molten iron.Based on the distribution ratios obtained in this work, recovery of PGMs was determined. The recovery of platinum, palladium and rhodium increase with increasing the mass ratio, Mmetal/Mslag. In the case of the conditions of Mmetal/Mslag = 0.04, the recoveries of PGMs showed more than 99.97%. The use of liquid iron and carbon saturated liquid iron as the collector metal is advantageous for the PGM recycling of the three-way auto catalyst. We found that PGMs are enriched to the molten iron or the carbon saturated iron and the slag loss of PGMs is negligible small."

Jan 1, 2014

By Louis J. Cabri, Donald Hoy

"Samples with contrasting gold mineralization were studied quantitatively prior to metallurgical tests. The AD samples are coarser-grained and characterized by abundant Sb minerals (jamesonite, berthierite, stibnite). The finer-grained MW sample has abundant pyrite and pyrrhotite, with arsenopyrite and galena next in abundance. A large number of gold mineral particles were determined by SEM investigation of hydroseparation concentrates, ranging from 150 to 597 per sample. The grain-size distribution of the gold minerals shows evidence of bimodal grain-size distributions (volume %), with the coarse fraction being most significant in sample MW-1 (maximum ECD=308µm). The coarsest gold minerals in the AD samples range from 139µm to 281µm ECD.The deportment of gold minerals is as electrum, aurostibite, native gold, and a possible new mineral (AuNiSb4). Gold also occurs in nisbite. The gold minerals are dominated by electrum in three samples and aurostibite is next in abundance. The major gold minerals are probably representative of three stages of gold mineralization. The first stage is represented by electrum, which is partly to completely replaced by Sb-rich mineralization forming aurostibite, and the last stage is native gold, often occurring as rims on one or the other earlier gold mineral. The gold minerals are strongly associated with sulphides in the AD samples (55 to 60 vol.%). At the grind used for the hydroseparation the liberated gold mineral quantity (volume %) is also significant, ranging from 65% for sample MW-1 to 30 to 37% for the AD samples.INTRODUCTIONThe Clarence Stream deposit is located 70 km south-southwest of Fredericton and 25 km northnorthwest of St. George, south-western New Brunswick, near the international boundary with Maine (Fig. 1)."

Jan 1, 2007

By R. Jackman, D. Koningen, G. Wilcox

"Gowest Gold Ltd. is in the process of developing the Frankfield East gold deposit located along the largely undeveloped Pipestone fault northeast of Timmins, Ontario. In addition to resource development and environmental permitting work the company has had an ongoing program of metallurgical and engineering studies aimed at evaluating options for processing the Frankfield East ore. Mineralization at the Frankfield project contains arsenopyrite and pyrite as the major sulphide minerals. Bulk flotation of all sulphides results in extremely high gold recovery. However, the gold is almost entirely associated with the arsenopyrite fraction of the ore and is refractory in nature requiring preoxidation treatment. Selective flotation was investigated to recover a gold-arsenopyrite concentrate thereby reducing the mass which would be subjected to further gold processing. As part of this work, a pyrite concentrate low in arsenic content was also recovered that would be suitable as a source of sulphur for a smelter (or other pyrometallurgical facility). Production of separate arsenopyrite and pyrite concentrates is frequently examined but rarely adopted due to the distribution of gold between the two products or the inability to achieve adequate separation. Several flowsheet options were investigated in the study. The best results were achieved following a sequential flotation flowsheet. The flowsheet configuration was key to meeting the targets for the two products. In this paper, the various options investigated are reviewed and the results of the final flowsheet are presented. The overall plan by Gowest was to evaluate all process options to bring the Frankfield East deposit into production. The ability to effectively separate the arsenopyrite and pyrite components in the ore provides Gowest with added opportunities to pursue both short and long term production scenarios."

Jan 1, 2012

By Rob Barber

This paper shares the experience of the Alberta Energy and Utilities Board (EUB) Field Surveillance Branch over the past few years in building relationships with Aboriginal communities. Our goal is to provide and encourage best practices that may benefit you and your organization and result in strong, mutually beneficial relationships with a focus on Aboriginal communities. Historical information provides insight that aids in establishing effective working relationships with Aboriginal communities. An important component is appreciation of the perspective of these communities, which is achieved through awareness training. The use of local Aboriginal resource people as part of the training is recommended. A plan that is supported by management and staff is essential and lays the foundation for successful relationships. However, the plan must be flexible enough to change as circumstances warrant. The concept of having local people in communities address local issues is essential. This ?grass roots? approach, combined with the goal of exceeding a community?s expectations with respect to addressing issues, will go a long way to establish trust and credibility. Measuring the effectiveness of this work is the final building block to complete the picture.

May 1, 2004

By Dave Rose, Jacques McMullen

"The Detour Lake mine is located 200 km northeast of Timmins, Ontario, Canada.The mill processes a free milling gold ore using both a gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 tpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The Detour Lake mine has one of the largest gyratory crusher in the world (60"" x 113"") and over the years, many improvements have been made to this crusher with the result of improving plant throughput. This paper will present how choke feeding the gyratory crusher has been found to be one of the main influences on crusher product particle size and plant throughput. It will explain how the effect of choke feeding the gyratory was measured and from that, the various changes made to improve choke feeding of the gyratory crusher.IntroductionOre is hauled from the open pit mine and dumped directly into a single 60"" x 113"" primary gyratory crusher. The live capacity of both the feed and discharge hoppers of the gyratory crusher are designed for two (2) truck loads each, assuming a nominal payload of 300 tonnes per truck. The surge bin under the primary crusher feeds an apron feeder that controls the ore feed rate at approximately 4,200 tph onto a 227 metres long x 1.52 metres wide belt conveyor with a nominal capacity of 4,200 tph.The primary crusher is operated at an open side setting of 172 millimetres to produce a F80 feed to the secondary crushing circuit of 135 millimetres."

Jan 1, 2017

By J. A. Meech, G. R. Baiden

"A dynamic simulation of a mine-mill complex has been conducted using networked microcomputers (IBM PC/AT and IBM PC/XT). These models allow simultaneous operation of an open pit using shovels and trucks, a primary crusher, and a secondary crushing plant. Each process transmits information via the network, linking all operations together. The effects of blasting, ore quality, equipment utilization and configuration on productivity can be studied either interactively or from a report listing at the end of each shift. Programs are menu driven leading the user through the decisions required in day to day operations. The mine-mill simulator is currently being used as a teaching tool at Queen's University to provide senior mining and mineral processing engineering students with an experience and appreciation for the operating problems across the mine-mill interface. The need for coordination and close communication between the mine and mill can be aptly demonstrated using these models. The simulator could be used to contribute to the training of operating personnel in a real mining operation. INTRODUCTIONThis paper describes a computer simulator that is capable of showing the interactions and operating strategies between a mine and a secondary crushing plant. The simulator uses two models developed at Queen's University; one for open pit mining and the second for secondary crushing. PITSIM is a dynamic shovel/truck haulage model origin2lly developed by P.D.D. Chick (1) and K.G. Fytas (2) to solve shovel/truck scheduling problems. CRUSHSOFT is a dynamic secondary crushing plant model developed by R.J. Tucker (3) and C.A. Harris (4) to study alternative operating and control strategies in a crushing plant."

Jan 1, 1987

By J. P. Van Cruyningen, M. J. Puro

"A 2400 acre extension to the existing Tailings Area is under development at Inco's Copper Cliff Milling operations.The new area is being developed in stages as production levels dictate thus minimizing immediate capital expenditures while permitting disposal operations to proceed as further site work progresses.The first stage of the new storage site will be fully operational by early 1987 and will include a 400 acre site specific to the storage of Pyrrhotite rejected from milling circuits. The Pyrrhotite site is located in the centre of the Tailings area and is designed for water cover throughout much of its projected life.The new development incorporates perimeter dams designed to operate with low phreatic levels for maximum structural stability. Acid seepage water is collected behind secondary impermeable dams for return to the Tailings Pond.Tailings are deposited by up-stream methods permitting segregation of coarse fractions for use in future lifts of the perimeter dams."

Jan 1, 1987

By Henry Stoch

It?s a green, green world ? Public concern about the impact of human activities on the environment and the roles that businesses play in that impact is rising. What?s happened in the last few months? ? Recent news: ? British Columbia announces carbon tax in 2008 budget ? Federal Court ruling stalls oil sands approvals due to a lack of consideration of GHG implications ? US Energy Independence and Security Act could limit government procurement of oil sands-derived fuels ? Western Climate Initiative (WCI) suggests a ?first seller? approach for regulating generators outside WCI jurisdictions ? Implications ? A cost for carbon has arrived ? The lack of a GHG strategy can have a material impact on your business ? Regulations in other jurisdictions could affect your organization

May 1, 2008

By Ahmad Ghahreman, Lin Li

Silver and cupric ions have been proven to play the roles of catalysts to promote the oxidation kinetics of chalcopyrite in acid solution. In this study, the interaction between silver ions and cupric ions during ferric leaching of chalcopyrite in sulfuric acid solution has been investigated. The electrochemical study by Tafel analysis showed a significant boost of dissolution rate for chalcopyrite dissolution in Fe3+- Cu2+ containing sulfuric acid solution after Ag+ was added in the solution. For 10 ppm Ag addition, the dissolution rate of chalcopyrite increased to 7.94 ×10-6 A/cm2 from 3.2 ×10-7 A/cm2, when Ag+ was absent. On the other hand, the effect of Cu2+ on the dissolution of chalcopyrite in Fe3+-Ag+ containing sulfuric acid solution was not obvious from electrochemical measurements. The chalcopyrite leaching tests in different acid solutions showed that silver addition had an obvious catalytic effect on promoting chalcopyrite dissolution. Comparing the leaching rates of chalcopyrite leached in Fe3+ containing, Fe3+-Ag+ containing, Fe3+-Cu2+ containing and Fe3+-Cu2+-Ag+ containing sulfuric acid solutions, it was found in Ag+-Fe3+-Cu2+ containing sulfuric acid solution, the leaching rate was highest among all the aqueous acid systems. Further leaching tests suggested that with increase of the Ag+ concentration from 0 to 20 ppm, the leaching rate of chalcopyrite in Ag+-Fe3+-Cu2+ containing sulfuric acid solution also increased and reached 57.62% with 20 ppm Ag+ addition after 24 h. INTRODUCTION Chalcopyrite is the most important copper mineral in copper hydrometallurgy and it accounts for nearly 80% of the universal copper resource (Olvera, Rebolledo, Mora, Dixon, & Asselin, 2018). The hydrometallurgy of chalcopyrite has been intensively studied with emphasis on solving the slow dissolution kinetics of chalcopyrite in acid environment. A variety of aqueous systems, such as sulfate (Hiroyoshi, Miki, Hirajima, & Tsunekawa, 2001), chlorides (Liu, Chen, & Yang, 2017), and ammonia (Hua et al., 2018) have been studied to improve copper leaching. From another perspective, chalcopyrite leaching studies have indicated that the mechanism of chalcopyrite dissolution in acid solution is essentially electrochemical (Li, Kawashima, Li, Chandra, & Gerson, 2013). Therefore, extensive studies have recently been carried out to explain the dissolution kinetics of chalcopyrite in different media by various electrochemical techniques.

Jan 1, 2019

By Stephen A. Gasiorowski, Frank J. Hrach, James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity - up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle-particle contact. The small gap, high electric field, counter-current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Jan 1, 2012

By Gary Anderson

??Privately Held Corporation ??Incorporated in Delaware, May of 2002 ??HQ in Malvern, PA (just outside Philly) ??Approx 40 employees ?9 Field Engineers ?MSHA Certified ?10 Development/NOC Engineers ?Site Survey/Site Design ?RF Engineers ??Standards Based ?IEEE 802.11 ??Commercial Off the Shelf (COTS) ?Gateworks, Ubiquity, Atheros, Linux Based ??Technology was developed and inspired by the lack of communications during the terrorist attacks of Sept. 11, 2001

May 1, 2009

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019

By Karl Marquis

La Mine Mouska exploite depuis deux ans certains blocs de réserve à l?aide de la méthode long trou. Même si, à priori, la méthode long trou semble rentable, le contrôle de la dilution ainsi que le respect d?un échéancier serré s?avèrent primordiaux afin que cette méthode d?exploitation puisse être justifiable économiquement. La présentation suivante fera la comparaison économique entre cette méthode et celle de chambre-magasin.

Oct 1, 2001

By Vu Van Dong

Resource estimation is the science of determining the amount and quality of a given material in the ground that has the potential to be mined at a profit. This is because during this time computers have become more widely available and more powerful and software packages have become more comprehensive and user friendly. Over the past three years The Mining Geology Company with the support from Vinacomin Group has developed the Coal Geological Modelling and Reserve Estimation ? VMG system. The VMG system enables the geological and mining engineer to start at the reserve estimation for the mine design and planning. The VMG system enables the national and international standards (NI43-101, CIM-Canada; SAMREC Code, Africa, and JORC Code, Australia) and user friendly with menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Geological and mining data input through digitized map files and drill-holes information files stored in the database that is an integral part of the VMG system with the main function for collection, validation, and recording, storing and processing of data will include both ?primary? (observation and measurement) and ?interpreted? data. It is recommend that data be stored digitally, using a documented, standard format and a reliable storage medium that allows for easy and complete retrieval of the data. The coal reserve estimation through standard polygon methods with the increased use of these mathematical techniques (geometrical modelling, geostatistical method, least square method, ?) over the last ten years corresponds, to some degree, to a decrease in both the amount of the coal deposit mapping and, in particular, coal seam structural interpretation and modelling, and permit rapidly evaluation of coal seam and overburden quality and quantity. The understanding of the relationship between the coal mineralization of interest and the likely related complicate geological processes and structure that govern its emplacement and geometry within the geological framework is essential to the establishment of the geological controls for coal mineralization. System outputs includes: drillholes summary reports, stratigraphy, cross-sections, isopach maps, structure, contour maps, premining and post mining topography maps, and 3D perspective view on coal seam structure.

Oct 1, 2009

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988