Search Documents

By Ken Dyck, Chuck Edwards

"Cameco's McArthur River is the world's largest high grade uranium mine. Production started in late 1999. Cameco carried out the engineering design and construction management for the McArthur River project, including all aspects of mining, ore handling and ore transportation. The ore composition was expected to vary dramatically (0 to 30% U3O8; 0 to 25% clay; etc). To cope with the composition swings, sizing screens were selected to provide classification in the grinding circuit. The grinding circuit started up close to the design to provide minus 500 micron slurry. The 50% solids (wt) ground ore slurry proved to be difficult to transport to and process at the Key Lake Mill. Slurry containing high concentrations of high density pitchblende (about spgr 8.0) and low concentration of stabilizing clays, would settle in containers. Ore transport efficiency to Key Lake was found to be unacceptable.A test classification cyclone was installed in the grinding circuit at McArthur River early in 2002. The cyclone operating parameters were not typical, but the cyclone was made to work very successfully. Transportation efficiency to Key Lake increased due to more stable slurry. Preferentially ground (fine) pitchblende particles were easier to leach at Key Lake. The radiation exposure for operators and maintenance personnel to handle the more stable slurry was also reduced.The classification sizing screens were removed from the McArthur River grinding circuit and replaced by permanent classification cyclones late in 2002.INTRODUCTIONThe McArthur River mine and Key Lake mill operations are located in northern Saskatchewan, approximately 650 and 720 kilometres from Saskatoon, respectively. Figure 1 is a location map. McArthur River is the world's largest, high-grade uranium mine, with a production capacity of 18.7 million pounds U3O8 annually. (Rosner and Edwards 1998, Dyck 2000, Jamrozek 2000, Rodgers 2001) Proven and probable reserves are more than 473 million pounds U3O8. McArthur River ore, grading on average 21% U3O8, is milled at Cameco's Key Lake operation, 80 kilometres southwest by road. McArthur River production began in December 1999."

Jan 1, 2004

By R. G. K. Morrison

By arrangement between the Ontario Mining Association and Messrs. John Taylor & Sons, Mining Engineers, 6 Queen Street Place, London, E.C.4, the writer was engaged for a period of not more than three months to report on the rockburst situation in Ontario mines. This was later amplified, by mutual agreement, to include, at the expense of detail, visits to the larger camps where rockbursts had not occurred, to get a general picture of conditions and to discuss the subject with operators in their respective areas. Scope of Activities Visits were paid to the following properties for the purpose of enquiry and discussion; the underground workings of those mines marked with an asterisk were visited on one or more occasions: KIRKLAND LAKE * Macassa Mines, Limited * Kirkland Lake Gold Mining Co., Ltd. * Teck-Hughes Gold Mines, Limited * Lake Shore Mines, Limited * Wright-Hargreaves Mines, Limited Sylvanite Gold Mines, Limited Toburn Gold Mines, Limited EAST KIRKLAND & LARDER LAKE Upper Canada Mines, Limited Chesterville Larder Lake Gold Mtng Co., Ltd. Kerr-Addison Gold Mines, Limited Omega Gold Mines, Limited PORCUPINE * Hollinger Consolidated Gold Mines, Ltd. * Mcintyre Porcupine Mines, Limited * Dome Mines, Limited * Buffalo Ankerite Gold Mines, Limited Paymaster Consolidated Mines, Limited Preston East Dome Mines, Limited Pamour Porcupine Mines, Limited Broulan Porcupine Mines, Limited Hallnor Mines, Limited Naybob Gold Mines, Limited Delnite Mines, Limited Moneta Porcupine Mines, Limited DeSantis Porcupine Mines, Limited Coniaurum Mines, Limited SUDURY lnternational Nickel Co. of Can., Ltd. * Falconbridge Nickel Mines, Limited LITTLE LONG LAC AREA * Little Long Lac Gold Mines, Limited MacLeod-Cockshutt Gold Mines, Ltd. Hard Rock Gold Mines, Limited Bankfield Consolidated Mines, Limited Magnet Consolidated Mines (1936), Ltd. à PICKLE LAKE AREA * Central Patricia Gold Mines, Limited * Pickle Crow Gold Mines, Limited UCHI LAKE * Uchi Gold Mines, Limited McKENZIE ISLAND AREA Gold Eagle Gold Mines, Limited * McKenzie Red Lake Gold Mines, Ltd. * Cochenour Willans Gold Mines, Limited RED LAKE * Howey Gold Mines, Limited Hasaga Gold Mines, Limited Madson Red Lake Gold Mines, Limited

Jan 1, 1942

By M. C. Villeneuve

A numerical modelling approach was developed to explicitly simulate geomechanical characteristics of intact rock: mineralogy, grain size and fabric. The approach involved creating a representative constitutive model for each of three common rock-forming minerals: mica, quartz and feldspar. The constitutive models developed are valid within the low confinement realm of excavation boundaries, where tensile fracture processes dominate. The mineral types were assigned to numerical elements, which were associated with each other through an algorithm created in a finite difference model, FLAC 2D (Itasca 2007a), to simulate real crystal geometries and orientations. The numerical models were used in a parametric investigation of the geomechanical characteristics and compared with published observations of the rock yielding process in laboratory testing. This approach has allowed the explicit grain-scale investigation of the impact of geomechanical characteristics on rock yielding at low confinement, leading to an improved mechanistic understanding of excavation-scale rock yielding processes at excavation boundaries.

May 1, 2009

By R. A. Hill, J. D. Pitts

"Long distance slurry pipeline systems have been successfully trans-porting steam coal, iron concentrates, copper concentrates and limestone for an aggregate of nearly 60 years and nearly three billion ton-miles annually. A phosphate concentrate pipeline is nearing start-up and systems for coking coal, lead/zinc concentrates and fly ash are planned. The solids pipeline concept, first patented in the early 1900's and commercialized in the 1950's, is now a proven technology providing an economic, environmentally pleasing and safe method for long distance bulk transport.The challenge for larger tonnage and longer distance movements of solids, for traversing increasingly rugged terrain in grass roots mineral developments, for transporting untried materials and for shipping more economic forms of proven materials still remains. This has necessitated continued refinements and optimization of the technology. The economic and environmental incentives for slurry pipelines when compared to other transport alternatives has justified substantial activity in this area. The scope of planned systems in coal, iron and other minerals is indicative of the firm place slurry pipelines will have in worldwide mineral development.In this presentation, the state-of-the-art in long distance slurry pipelines is reviewed with a focus on major systems of interest to the mineral processing industry. An overview of new developments in the application of this concept is presented, and finally, a projection of the future of pipelines in mineral development both worldwide and in Canada is discussed."

Jan 1, 1978

By M. G. Dellow, D. W. Hendriks

"In early 1988 the decision was made by Noranda Minerals Inc. to install pressure filters at the GECO mill to replace the vacuum disk filters and bunker-C fired rotary kiln dryers. Two filters were installed, one for copper concentrate and one for zinc concentrate. Completion of the project was scheduled for the third quarter of 1989. The filters were made operational in October 1989. Some work remains to be done yet on loadout conveyors for total project completion. Capital expenditures for the project have been approximately $2,700,000 to date. The paper describes the selection criteria for the filter, the installation, startup and associated problems.1. INTRODUCTIONThe filter model chosen for the project was the Verti-Press model VP-50-6(7) (Figures1 ,2 and 3) by Filtra Systems of Farmington Michigan, USA. The decision to purchase the Filtra Systems filter was based on gaining familiarity with a different, mechanically simpler pressure filter than the Larox design and to a lesser extent a necessity for repairs to the the disc filter, rotary kiln dryer system used at the GECO operation for its' copper and zinc concentrates. The fact that it is manufactured in North America was an important consideration. The same basic principles of pressure filtration as the Larox machine are used but the implementation is quite different and somewhat simplified with some interesting innovations. 2 filters were installed to allow direct and immediate comparison of the same machine on both fine and coarse materials. Copper concentrate is reground for cleaning on the flotation circuit while zinc is not. Screen analysis of composited samples of concentrates for 1988 indicated that expected copper concentrate would be approximately 66% minus 400 mesh and zinc 50% minus 400 mesh (Tables 1 & 2).The filter is composed of six horizontal chamber module layered vertically and held together in a frame by 1 O large bolts; torqued down to 4000 ft-lbs. 6 individual belts are used; each with its own drive system. The belts themselves are of a 3 piece design with a filter cloth portion, a support belt and a rubberized intermediate portion. They are held together with steel clipper lacings. A basic description (1) of the filter operation is as follows. ""The horizontal filler chamber is closed by hydraulically pressurizing seals across each end of the filter chamber to 200 psi. The feed pump then pumps slurry into the filter chamber. Suspended solids are retained on the filter belt and the filtered solution drains into a lower drip tray and flows from the filter by gravity. At the end of the filtration or feed cycle, a rubber diaphragm in the filter chamber is pressurized hydraulically to 100 psi pressure. This removes all free liquid from the filter chamber and the filter cake. After the diaphragms are retracted the filter cake is blown with compressed air to remove any residual cake moisture. The seals are then retracted and the belt is advanced to discharge the filter cakes. During the cake discharge the belts are washed with a spray header located at the drive end of the filter. The belt assemblies move one (1) complete revolution during the cake discharge cycle. The cycle automatically repeats until the filter is shut down by the operator."

Jan 1, 1990

By Jocelyn Bouchard, Claude Bazin, Sami Makni, Rolando Quispe

"Finely disseminated minerals in ores require intensive size reduction to achieve sufficient liberation for the subsequent concentration process. The use of small grinding media in conventional ball mills as a replacement for the usual 2.5 to 3.8 cm balls (1.0 to 1.5 in) produces a finer size distribution at a lower power drawn by the mill motor. However, the conditions ensuring a successful application of using small media for fine grinding are still not fully understood and some plants faced issues to keep the newly introduced steel charge inside the mill during industrial trials. The retention conditions of small media are investigated in this paper using a continuously operated 40 x 40 cm laboratory grinding mill. The tests assess the effect of the steel charge level, the slurry solids concentration and the feed rate on the rate of ejection of the grinding media. The dominant variable is found to be the filling of the mill with the grinding media, followed by the mill feed rate. Results show that increasing the slurry solids concentration within a grinding mill may be favorable for the retention of the media inside the mill.IntroductionProcessing of complex ores often requires the use of fine grinding to liberate finely disseminated minerals. Grinding requirements for a P80 of less than 0.02 mm are not uncommon, and different grinding mills are available for such application (Leonida, 2014; Pease et al., 2006; Davey, 2006; Orford et al., 2006; Nesset et al., 2006). Even conventional horizontal ball mills charged with of 2.5 cm or larger grinding media can be used for fine grinding. However, simulation (Orford and al., 2006) and plant observations (Alves and L-Bouchet, 2005; Brisette, 2010; Brisette and Roman, 2012) demonstrated the advantages of using smaller grinding media in terms of size reduction and energy consumption."

Jan 1, 2015

By Lyne Côté, Jose Adante

"The Caribou underground mine, 50 km west of Bathurst, the Restigouche open-pit mine, another 30 km west and the concentrator located at the Caribou mine site resumed operations in July 2007 after a nine year shutdown. The Caribou operations achieved commercial production on Jan 1. By June, 2008, all metallurgical targets had been achieved or surpassed with the production of lead and zinc concentrates assaying approximately 50% Zn and 45% Pb respectively with recoveries exceeding 80% for Zn and 70% for Pb.The deposit features very fine-grained massive sulphide mineralization, which in the past has proven difficult to process. ISA Mill Ultra Fine Grinding Technology in combination with conventional flotation technology is used to process these complex oresSeveral modifications arising from experience gained from past operations, an extensive research project at Lakefield Research and post startup flow sheet and reagent alterations have been employed to achieve this break through performanceThis paper describes the design, start up and optimization of the Caribou operations including the many challenges faced including the flotation of mineral particles with K80s ranging from 35µm to 8µm.HISTORICAL BACKGROUNDThe Caribou massive sulphide deposit was discovered by Anaconda geologist Cam Cheriton in 1959. Anaconda initiated an extensive underground exploration and discovered a super gene copper blanket which was developed into a small open-pit mine-mill operation that ran from 1970 until the depletion of the copper ore in 1974. East West Minerals, an Australian public company, purchased the mine in 1986 and operated for only seven months producing a single bulk lead-zinc concentrate. In 1995, Breakwater acquired the Restigouche Open pit and Caribou underground deposits. Breakwater began milling operations in July 1997 but Caribou Mine failed to commercialize production, and the company decided to shut it down in August 1998, because of declining metal prices. The mill was plagued by mechanical and design problems, but deficiencies in metal recoveries prevented the operation from reaching desired levels."

Jan 1, 2009

By S. A. H Tyrrell, R. Rotzinger

"Taseko Mines Limited recommenced operation of the Gibraltar copper-molybdenum mine in 2004 and embarked on series of development projects to modernize the mine and increase throughput capacity. The Gibraltar Development Plan 3 (GDP3) project included a second stand-alone copper-molybdenum concentrator, a stand-alone molybdenum separation plant and associated services. Ausenco was contracted to commence the detailed design in 2Q2011, commissioning commenced in 4Q2012 and first ore was processed in 1Q2013. This paper discusses the design, implementation and commissioning of the GDP3 Concentrator.INTRODUCTION The Gibraltar Mine (Gibraltar) property is located in the Cariboo Region of south central British Columbia, approximately 360 kilometers northeast of Vancouver. The site is accessed via an 18 kilometer paved road from the town of McLeese Lake, which is located on the province’s main north-south highway between the cities of Williams Lake and Quesnel. Gibraltar was originally developed by Placer Development and commenced production in 1972. Gibraltar was acquired, while on care and maintenance, by Taseko Mines Limited (Taseko) in 1999 during a period of unusually low metal prices. Taseko recommenced operations at Gibraltar in 2004, and embarked on series of development projects to modernize the mine and increase throughput capacity. The 1972 Gibraltar process flowsheet incorporated two-stage crushing followed by rod and ball milling and flotation. In 2008 Gibraltar completed their first development stage that included the installation of a SAG mill, converting the existing rod mills to ball mills and adding additional flotation capacity. Gibraltar continued development with the installation of an in-pit primary crusher, expansion of the bulk regrind circuit, expansion of the cleaner flotation circuit, replacement of the tailings pumping system and replacement of the concentrate filters and dryer."

Jan 1, 2014

By F. P. Hassani, H. B. Poorooshasb

"A kinematically admissible velocity field is applied to study the arching phenomenon in a cohesionless granular backfill placed between two rough vertical inflexible walls. The study is different from the previous works which are almost entirely based on statically admissible stress fields. It is shown that the development of arches is strongly influenced by the previous loading history of the backfill which controls the nature of the constitutive laws that govern the mode of stress deformation of the backfill. This preliminary study employs simple models in order to show the potential use of such an approach in evaluating and understanding mine backfill behaviour in the underground excavation. The pressure exerted on the floor supporting the backfill is also studied in some detail.INTRODUCTIONAlthough the importance of the design of mine backfill has been discussed extensively by a number of authors, i.e. Hassani et al. (1985), such theories have not as yet been incorporated in design criteria for underground mine backfilling operation . One factor that such theories must incorporate is the so-called arching action .The phenomenon of arching has been the subject of study by many researchers in the field of civil engineering and mining engineering. Among these scholars the works of Terzaghi (1943), Krynine (1945), Lusher and Hoeg (1964) and Handy (1985) are noteworthy. All these authors use a statically admissible stress field as a starting point to develop their theories. The approach taken by the authors of the present paper is completely different because they employ a kinematicallyadmissible velocity field. It is their belief that the arching phenomenon is closely linked to the interlocking of grains as manifested by the degree of dilatation of the granular mass when subjected to a shearing process.This paper is written in the following sequence. To define the interlocking quantitatively it is necessary to state the constitutive law governing the stress deformation characateristics of the granular mass. This is done in the next section as the law proposed by Poorooshasb and Pietruszazck (1985, 1986) is stated and simplified to suit the present analysis. Next the mode of formation of an arch in a simple system consisting of a mass of backfill sandwiched between two vertical rough walls of infinite extent is examined. The velocity field obtained from the above example is used to obtain solutions to two more complicated situations. The first situation assumes that the backfill is supported, in addition to the vertical rough walls, by a Winkler foundation at its base. The second situation assumes that the Winkler foundation has been replaced by a horizontal beam of uniform section and simply supported at its extremities. The findings of the study are summarized and their practical implications discussed in the concluding remarks."

Jan 1, 1989

By R. Al-Hent, M. Aissa, J. Asfahani

"This paper focuses on determining the favorable geological and hydrogeological conditions for forming uranium occurrences in the Froqlos-Jabal Abou Rabah region, Palmyrides, Syria. Eighty rock samples from this area were analyzed by spectrometric gamma-ray technique to determine the radioactive concentrations of eU and eTh, and of %K. Uranium concentrations in shallow and deep groundwaters were also determined. High uranium concentrations were registered owing to the presence of phosphatic outcrops in the study region. The uranium migration trends and its remobilization were analyzed through the analysis of the behavior of eU, eTh, and their ratio. A positive relationship between eU and eU/eTh, and a negative relationship between eTh and eU/eTh in geological formations of different ages supports the secondary remobilization of uranium. The role of groundwater movement in transportation and redeposition of uranium mineralization is discussed: deep waters are less oxidizing than near-surface waters, and do not appear to have significantly remobilized uranium. This indicates that the source of secondary uranium mineralization is surficial or near surficial, and is mainly related to the leaching of outcropping phosphatic layers.Integration of the results with established radioactive and geological sections reveals four radioactive anomalous zones: north Froqlos, Kherbet Hannora, northwestern flanks of Jabal Abou Rabah (Kherbet Al-Hajar), and the northwestern limit of the Ghuntor depression. The high uranium concentration in north Froqlos is because of its original presence in the phosphate beds and extensive fracturing, which allows groundwaters to penetrate and remobilize the uranium. High uranium concentrations in the other three locations are caused by the presence of evaporites and capillary action, which draws solutions upwards and causes redeposition as surface crusts (gypcrete)."

Jan 1, 2009

By G. Couture

"The Glencore Raglan mine Concentrator, located in Quebec’s Nunavik region, has been in operation since 1997. The nickel metallurgical plant was originally designed to process 100 tonnes per hour of ore to produce 130 000 tonnes of nickel concentrate per year at 16% Ni. The increased grinding capacity and the discovery of rich ore bodies have increased the annual production to more than 190 000 tonnes of concentrate at 19% Ni. In 2014, the Metallurgical group, with support from BBA, implemented an expert control system on the flotation circuit. This project was initiated to cope with the high variability of the concentrator’s feed. Increasing the plant recovery and final concentrate grade were also important project objectives. The implementation of the expert system ensures better control of concentrate inventory while maintaining maximum plant throughput. This paper describes the successful implementation of the new control system, the control technology selection and the flotation circuit optimization. It will also discuss the performances obtained with this new approach and the improved process stability.IntroductionThe Raglan Mine is located in Northern Quebec along the 62th parallel. It has been in operation since 1997 and was originally designed to produce 130 000 tonnes of concentrate annually at 16% Ni. The increasing of the grinding capacity and the discovery of rich ore bodies have increased the annual production to more than 190 000 tonnes of concentrate between 18 and 20% Ni."

Jan 1, 2015

By J. A. Finch

"A method of sampling and presenting bubbles for imaging for use in full-size flotation cells is described. The device (bubble viewer) comprises a tube attached to a sealed glass viewing chamber. The assembly is first filled with frother-containing water (to prevent coalescence) and the tube immersed at the desired location below the froth. For a few minutes bubbles are collected in the viewer free from slurry and are readily imaged. To reduce bubble overlap and the problem of defining the plane of view, the viewing chamber has a sloped side. Bubbles rise, encounter this slope, spread into a single plane and slide up. This simple expedient virtually eliminates overlap and provides an unambiguous focus plane - the underside of the sloped glass. The bubble image is captured and processed to give size data. The bubble viewer has been employed at several concentrators on different types of flotation cells. Examples of the images are given. The impact of position in the cell and the effect of changing gas rate on bubble size are illustrated. This technique provides a sensitive measure of the effects of process variables on bubble size.INTRODUCTIONDespite the extensive use of flotation in the mineral processing industry, the methodology employed for cell design is largely based on empirical rules rather than on first principles. One of the main reasons for this state of affairs is that the local flow structures encountered in industrial-scale machines are very complex. These flow structures are difficult to simulate under the controlled conditions of the laboratory and the difficulty to solve the mathematical models that treat the randomness of such flows also mean theoretical treatment is limited. Understanding flotation cell hydrodynamics requires reliable data, which involves the implementation of measurement techniques capable of performing both at the laboratory- and the industrial-scale, In addition, it is desirable that such techniques are amenable to automation to reduce extensive manual intervention in the data collection process."

Jan 1, 2002

By André van Wageningen

Long term mine scheduling is one of the most difficult optimization problems. The problem is said to be NP-complete in that the best possible solution cannot be found any quicker than checking all possible permutations and combinations. In current mining operations, it is important to report changes in long term plans as soon and as accurately as possible. Where geological data can change rapidly, such as in narrow vein deposits, the need to quickly identify and optimize different long term alternatives becomes a difficult task and can lead to many permutations of the long term mine plan. The question arises, is the new plan optimal or not? Can the company objectives be met while adhering to operational constraints? Although a number of optimization techniques have been used in the past, many include significant simplifications or fail to produce acceptable results within the required timeframe. Genetic Algorithms (GAs) are among the most promising optimization techniques within operations research. They are based on natural selection and evolution of solutions to complex problems. They have been known to quickly converge within a few percent of the optimal solution by examining only a fraction of the possible permutations. The GA itself contains very little problem specific information and, as such, in this study, has been linked to a discrete-event simulation (DES). The DES is able to evaluate each sequence proposed by the GA and determine the effectiveness and value of each schedule. The DES feeds information regarding the feasibility and quality of the solutions back to the GA during the optimization process. In this paper, GAs and DES are described and the coupling of the two methods is outlined. The GADES module is then used to ?optimize? a narrow vein theoretical case study and the results discussed in a broader mining context.

Oct 1, 2004

By Christoph Broeckmann, Andrew Gardula

"The adoption of high-pressure grinding throughout the cement industry has yielded enormous savings in energy and wear material costs. There are also a number of installations, which are applied in iron ore and kimberlite processing operations. High pressure grinding offers the same potential for energy and media savings, as well as opportunities for improved, downstream metallurgical performance, in hard rock mineral processing. This paper focuses on developments in machine design and wear surface engineering for high-pressure grinding of the hard rock ores in the mineral processing industry.INTRODUCTIONIn the early eighties 3.4 % of the world electric energy was consumed for crushing and grinding operations of minerals and 0.6 % in the ore dressing industry. During that time using a laboratory press Prof. Schönert found that interparticle comminution at high pressure requires remarkably less energy as conventional grinding technologies. In grinding of cement clinker he expected energy savings between 33 and 50 % compared to ball mills [1]. Piston presses are limited in throughput. Thus, the principle of interparticle comminution was adapted by the use of high pressure grinding rolls (HPGR) to a continuous plant process. Figure 1 shows the main components of a roller press: The roller nip of width s is formed between the floating roller (1) and the fixed roller (2). The diameter of the rolls will be denoted with D, the width with B. The total press force F can be adjusted using a hydraulic system with two or four pistons (3). In order to compare machines with different roll geometries the specific pressing force p is introduced:"

Jan 1, 2005

By S. J. Haynes

"This paper documents the characteristics of the different quartz veins, and their relation to gold, in the turbiditic Meguma domain of eastern Nova Scotia. Eleven different types have been distinguished in the greenschist facies on the basis of form, internal structure, mineralogy, wallrock alteration and crosscutting relationships to each other and to regional structures. Gold is present as rare visible disseminations in host rock slates and in ore-grade, early-formed veins, that pre-date the formation of upright Acadian folds and intrusions of Devonian granitoids. Four vein types pre-date Acadian folding. Five gold-deficient vein types are associated with Acadian folding (syndeformation); whereas two gold-deficient vein types clearly post-date this deformational event: Previously unreported, wall rock alteration is associated with early crosscutting and semiconcordant auriferous veins. In contrast, early stratiform veins are devoid of wallrock alteration. It is suggested that the auriferous vein arrays formed as submarine exhalitive systems over synsedimentary tensional faults and that the Meguma domain may represent the opening of a basin similar to the modernGuaymas rift .IntroductionThe term ""turbidite-hosted gold deposits"" is introduced to distinguish gold deposits contained within a turbiditic sequence of wackes and shales (or their metamorphosed equivalents) from gold deposits in other types of sediments. Usage and justification for the term is similar to ""carbonate-hosted lead-zinc deposits"" or ""volcanogenic massive sulphides"". A range of different characteristics can be present in individual deposits, some of which may be indicative of specific deposit types in the same manner that volcanogenic massive sulphides can be subdivided into ""Cyprus type"", ""Kuroko type"", ""Besshi type"", etc. Historically, gold deposits hosted by turbiditic flysch were an important class of quartz-vein gold mines in the 19th century. They included the goldfields of Victoria, Australia, Otago, New Zealand and Nova Scotia, Canada. Production from most of these fields had ceased by World War II and interest in this type of deposit waned. However, the recent exploration interest in gold has resulted in both re-assessment of the classical mining camps and the discovery that ""turbidite-hosted"" gold deposits are present in many parts of the world.Mapping of the regional geology and gold deposits of the Megumadomain of Nova Scotia was carried out by E.R. Faribault of the Geological Survey of Canada between 1886 and 1939. Faribault produced a comprehensive series of maps and reports for each gold district, a compendium of which was published by Malcolm (1929)."

Jan 1, 1987

By F. D. Ford, Z. Dai, A. Byers

Manitoba Mining and Milling operations consist of three underground mines (Thompson T1, T3 and Birchtree), feeding the Thompson Mill. Three years ago, a collaborative effort involving Mines Exploration, Mines Project Development Group, Mill Technical Services and Vale Base Metals Technical Excellence Center was initiated to establish and verify the cause of high variability in concentrate quality and Ni recovery at the Thompson Mill. One outcome of this work was a program to systematically characterize the mineralogy and metallurgical performance of current and future orebodies feeding the mill. Mineralogy results show that high value enabling ores typically have a high pentlandite to pyrrhotite ratio and benign silicate mineralogy (mostly quartz and feldspar from sedimentary host rocks), while metallurgically challenging ores contain some combination of pyrite and/or hexagonal (non-magnetic) pyrrhotite and/or elevated quantities of talc (with associated carbonates) derived from altered ultramafic host rocks. The metallurgical performance of these two ore types has been simulated by an Excel particle flotation model, which calculates the relative floatability of particles based on the particle’s mineral composition and mineral locking determined from MLA images. The relationship between these mineral properties measured by MLA and metallurgical performance was established using 13 monthly composite samples from Thompson Mill. The model was then validated with results of laboratory flotation experiments on individual orebodies submitted for evaluation. The validated model can be used to predict plant metallurgical performance based on individual ore bodies feeding the mill. Individual orebody’s grade-recovery curves are assumed to be additive, and can be weighted in proportion to the mill feed to predict mill recovery over the same time period. The ore mixing can be done with a simple Excel spreadsheet and comes with a graphical output for easy visualization of the resulting grade-recovery curve.

Jan 1, 2015

By J. A. López-Molina, S. García, V. Castellanos-Pedroza

"Groundwater inflow into underground constructions may cause hazardous working conditions and environmental problems. It is essential to localize and characterize potential flow paths and to estimate the amount of water leakages, so that appropriate sealing works can be performed. Estimating the amount of water ingress is a multi-phase process starting from qualitative and quantitative examination of rock mass. Due to association of uncertainty, vagueness and incompleteness with the monitored data set, particularly resulted from the in situ tests, accounting relevant approaches such Fuzzy Logic and Recurrent Neural Networks, are proposed in this research for learning acquisition, extraction of rules and prediction of behaviors. The computational set of artificial tools permits using the complex information entities or information granules (rock types, geologic structures, hydro-fracture potential) for data abstraction and derivation of knowledge from records (numerical or linguistic format). This is more a theoretical perspective than a set of methods or principles. As a theoretical perspective, this proposal encourages an approach to data that recognizes and exploits the information present in indexes at various levels of resolution or scales. In this sense, it encompasses the methods which provide flexibility and adaptability in the resolution at which knowledge or information is extracted and represented. The product of merging these tools is a 3D artificial-mapping of rock classification (Qi-system), geological conditions and Lugeon units that permits, as far as possible, to understand more and better the flow behavior."

Jan 1, 2015

By Maarten van de Vijfeijken, Marco Rufli

"By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The advanced operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore highest availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives (Ravani von Ow and Bomvisinho, 2010; Ravani von Ow and Gerhard, 2010). However this paper will not only show and explain the operational benefit of these functions, but will focus on the experiences gained with this kind of sophisticated ring geared mill drive system. Several measurements of different operating conditions (starting, frozen charge remover, controlled roll back, backlash, etc.) made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. Also the accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.INTRODUCTIONLooking at the demands of grinding mills, we can split them into operational, maintenance and protective demands. For smooth and safe operation, it is important that critical situations are avoided as much as possible. Maintenance functionality must be quick and easy to execute, while protection of the system is important during all operating conditions. ABB has considered all these demands during development of their dedicated mill functions. By adding an additional controller (mill controller), not only a lot of application related functionality and protection is included, but also the interface between the mill drive system and the customer’s distributed control system (DCS) is simplified."

Jan 1, 2011

By A. J. MacRae

Metallurgical furnaces are made up of complex multi-component systems that must function either together or in parallel for safe, and reliable operation. Thermal expansion of single material components experience induced stresses during heating and cooling, which can lead to cracking or failure. Multi component elements and systems can experience significant thermally induced stresses during both steady state and transient temperature conditions. Examples pertaining to temperature effects on refractory, copper cooling blocks, furnace shells, and complete systems will be discussed. The purpose of the paper is to highlight how stresses and strains are developed due to differential thermal expansion.

Jan 1, 2015

By Richard Maurice

RÉSUMÉ La restauration du site minier Poirier, à Joutel s?est déroulée entre 1998 et 2001. Le principal élément des travaux a été la restauration du parc à résidus et des zones d?épanchement qui totalisaient 4,5 millions tonnes de résidus répartis sur une superficie de 74 hectares. Les résidus sont fortement générateurs de drainage minier acide. La première partie de la présentation consiste en un bref rappel du concept de restauration suivi d?une description des principaux éléments de travaux avec l?emphase sur les leçons apprises de l?exécution des travaux. La deuxième partie de la présentation est axée sur les résultats du programme de suivi en cours depuis la fin des travaux en 2001. Les éléments de suivi se rapportent à la baisse du niveau de la nappe phréatique à l?intérieur de la cellule, au tassement des résidus dans la cellule, aux mesures de température et d?oxygène à l?intérieur de la cellule et finalement à l?amélioration dans la qualité de l?eau de surface. ABSTRACT The reclamation of Poirier Mine, in Joutel, was carried out between 1998 and 2001. The main component of the works has been the reclamation of the tailings basin and tailings spill area which contained a total of 4,5 million tonnes of tailings and occupied some 74 hectares of ground surface. The mine tailings are highly acid-generating. The first part of the presentation will deal with a brief review of the reclamation plan followed by a short description of the main work components laying emphasis on experience gained during construction. The second part of the presentation will deal with the results obtained from the environmental monitoring program still in progress since the end of reclamation work in 2001. The aspects discussed include the drawdown of pore water inside the covered tailing pile, the settlement of mine waste material, the monitoring of moisture, temperature and oxygen underneath the liner and finally, the reduction of loadings in surface water.

Nov 1, 2002