Search Documents

By Albert G. Zima

THE conservation of strategic materials during war rime gives rise to many problems not commonly encountered in times of peace. During normal times, when world trade is unrestricted, we are apt to become lavish to a point of extravagance in our use of those materials which, during rime of war, become scarce owing to inadequate transportation and production facilities or because the enemy may be in position to control sources of supply. It becomes necessary, then, to enforce rationing of available sup-plies, and in some cases, where such supplies are wholly inadequate, we find we must resort to the use of substitute materials. We are now confronted with such a problem to an extent never before experienced, with the result that many of the commodities upon which our civilization depended are now either shut off completely or, because of the heavy demand occasioned by war production, are not available in sufficient quantities to meet requirements predicated on peace-time standards and manufacturing methods. It has become necessary, therefore, to make many changes, some of them very drastic indeed, to enable us to carry on our war effort effectively. This? discussion will deal briefly with one phase of this problem, namely, the conservation of alloys required in the making of steels necessary for war production. In line with a request from the War Production Board, the Technical Committee on Alloy Steels of the American Iron and Steel Institute made a study of experimental steels embodying the !east amount of alloying constituents, with the objective in mind of substituting these steels wherever possible for the standard alloy steels used heretofore. This study embraced the following phases: (1) The availability of silicon and manganese; (2) The average quantity of alloying elements recoverable from scrap; (3) The effect of increases in manganese and silicon contents on the general properties of steel; ( 4) The elements and ranges of elements which might be used to duplicate the hardenability of the steels now in use; (5) The effect of combining several elements in small quantities upon the properties of steel at various hardness and strength levels; (6) A determination as to whether or not the steels selected would suffice for general application. Working on this basis, the Committee arranged for the manufacture of several heats of steels containing various combinations of different amounts of such elements as silicon, manganese, chromium, nickel, and molybdenum. The steels thus produced were compared by hardenability tests.

Jan 1, 1943

By J. E. Hawley

"The zinc-lead deposit of the Lake Geneva Mining Company is on lot 7, con. VI, Hess township, Sudbury district, Ontario, about 10 miles northwest of the northern rim of the Sudbury Basin. Though a relatively small deposit, it shows some rather interesting relations to cross-cutting, pre-ore, quartz diabase dykes, which merit description.The deposit was discovered in October 1924 by J. H. Collins beneath iron-stained drift and oxidized sulphides. This proved to be the northwestern extremity of the orebody, the remainder of which extends southeast below swampy ground. Exploration began in 1927. In 1928 a vertical shaft was sunk to 250 feet and a level established at 235 feet. Later the shaft was deepened to 400 feet and new levels opened at 315 and 375 feet. In 1943 an inclined winze was sunk below the vein from the 315-foot level to a vertical depth of 640 feet, and two additional levels were opened at 525 and 615 feet respectively.The geology of the area has been described by T. T. Quirke (1), F. F. Osborne (2), F. J. Alcock (3), and Ralph Tuck (4). Private reports have also been made by Carl Tolman, J. E. Gill, and K. W. Fritzsche. Tuck's paper, covering the work completed to 1930, gives a detailed account of the character of the ore and enclosing rocks.Up to May 1944, when the property was closed, all ore above the 375-foot level and a small tonnage from below this elevation had been removed. Ore mined from 1941 to 1944 yielded the following:"

Jan 1, 1954

By V. Vakiloroaya

The paper aims at developing a hybrid solar-assisted air conditioner system for performance enhancement and energy efficiency improvement. To increase sub-cooling of the refrigerant at partial loads, we propose a new discharge bypass line together with an inline solenoid valve, installed after the compressor to regulate the mass flow rate of the refrigerant vapour passing through a hot water storage tank. For control design, a lumped parameter model is first developed to describe the dynamics of the system in an explicit form of input-output relationship. The system has been fully-instrumented to examine its performance under different operation conditions. The system model is then validated by extensive experimental tests. The predictions from the models exhibit a good coincidence with experimental results, judging by an RMS error less than 15%. Based on the obtained dynamic model, a linear quadratic regulator (LQR) is applied to optimize a cost function of the output errors and control efforts. The key challenge is to regulate the refrigerant temperature entering the condenser by controlling the valve opening. The design approach is then tested in a transient simulation tool to predict the system performance in transient conditions. The experimental results obtained from implementation with PLC demonstrate that the proposed system delivers higher system efficiency owing to the higher refrigeration effect in the direct expansion evaporator. Thus, the novel development is promising for improvement of energy efficiency, enhancement of the system performance while fulfilling the cooling demand. Consequently, between 25 and 43% of monthly electricity can be saved on average.

Aug 1, 2013

By Z. Huda

The effect of various percentages of cold-working and recrystallization on the microstructure and hardness of commercially-pure aluminum plate, has been studied. The 'A critical deformation for the aluminum, has been determined. Experimentation involved cold rolling and recrystallization processes followed by quantitative metallographic practice and the hardness measurements. The raw material chosen was a plate of commercial aluminum which was cold rolled to different percentage of cold-work and then recrystallized by heat treatment at 150°C. The critical deformation percentage of aluminum was computed to be around 30% of cold-worked.

Jan 1, 2007

By H. R. Butler, R. N. Browne

"The International Nickel Company of Canada Limited consumes some 33 ½ millions of gallons of fresh water and reuses more than 100 millions of gallons of water daily. The continuing search for suitable recycle methodology has enabled the Company to put one 25,000 TPD mill on line utilizing recycled water entirely and a second 35,000 TPD mill is under construction which will likewise employ the concept of recycled water. Future milling plans are aimed at the replacement of all fresh water with recycled water, including sewage effluent and mine waste water.WATER REUSE AT INCO’s SUDBURY MILLSAs man searches unexplored horizons for new and economic industry, he must be constantly and acutely aware of the presence or absence of that precious commodity without which Industry, indeed Man himself, could not survive -- W A T E R. The water requirements of the world today are magnanimous, considering that in 1960 the estimated consumption in the United States was over 300 billion GPD (l) or more than 1,700 GPD per person(5) The magnitude of the problem can be visualized as one considers that three times this quantity of water will be required in the United States by the year 2000, when the dependable supplies of water are estimated to be only two-thirds of that required(2). How, then can we continue to wreak such havoc on that life-sustaining substance - WATER?"

Jan 1, 1970

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By A. Shaak

The town of Hedley is some 200 miles due east of Vancouver and lies in the bottom of the Similkameen River valley, at the junction of Twenty Mile creek, at about the 1,700-foot elevation above sea level. The Nickel Plate mine camp is on Nickel Plate mountain at an elevation of about 5,600 feet, four miles slightly east of north from Hedley, to which it is connected by 9 miles of road, and by 10,000 feet of tramway and electric railway. The latter is used both to transport the ore to the 275-ton mill at Hedley and to furnish the mine with supplies. History The Nickel Plate claim was staked in 1898 to cover the sole outcrop of the Nickel Plate system of orebodies. Soon afterwards it was optioned by the Marcus Daly interests of Butte and underground exploration commenced. Early exploration was successful, and a power plant, tramway, and mill were constructed. The mill began operations in 1904. Production under Daly control ensued from June, 1904, to August, 1909, and amounted to 167,000 tons. The Hedley Gold Mining Company was organized and commenced operations in 1909. The capacity of the mill was increased by stages to 200 tons and a steady production, except for short periods in winter, was maintained until 1930. By 1930, gold to the value of nearly $10,000,000 had been produced since the discovery in 1898. The South American Development Company optioned the property in 1932. Active exploration was conducted during 1933 and 1934 by the Kelowna Exploration Company, a subsidiary of the South American Development Company. This work was sufficiently successful that, coupled with the increase in the price of gold from $20.67 to $35.00 per ounce, production re-commenced in December, 1934, and continued uninterrupted until July, i946, when, along with all B.C. gold mines, a strike closed operations. Under the present ownership, the mill capacity was increased to 275 tons.

Jan 1, 1946

By C. A. Campbell

"There has been a significant reduction in maintenance hours and improved performance by maintenance crews at the MacLeod mine since the introduction of a Maintenance Control system which includes the use of maintenance standards. This paper deals with the steps taken to develop and implement the program. The objectives of the program and the organization and training of the control group are outlined. The work-order system, standards application, classification of work and the preventive maintenance procedures will be discussed.All maintenance information is processed on a Model 360-20 IBM computer, which turns out maintenance records and control reports for management action. Information in these reports, and reasons for reporting, will be discussed and the benefits resulting from the program reviewed."

Jan 1, 1973

By H. Mindivan

In the present study, the feasibility of recycling AA6061 Al alloy chips by a combination of ciyomilling, cold compaction and hot extrusion processes was investigated. Furthermore, the effect of Al powder addition to the recycled Al alloys chips on the mechanical properties was investigated. The characterization of recycled Al alloys was made by structural examination and mechanical tests (hardness, compression and dry sliding wear tests). The results indicated that by increasing wt. % of Al powder added to the recycled Al alloy chips the studied properties (the density, hardness, compressive strength and wear resistance) increased due to reduction of porosity in the recycled Al alloys.

Jan 1, 2011

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018

By D. M. Baird

"THE Island of Newfoundland lies on the extreme eastern edge of the continent of North America and at the extreme northeastern end of the Appalachian geological province. Its belonging to the Appalachian province is shown in the geological history of the region and in the rock types and structures.Geosynclinal sedimentation in early and middle Palaeozoic times was interrupted by Taconic and, more profoundly, by Acadian, mountain building activity. Mid-Palaeo-zoic intrusions range from masses of serpentinized ultrabasic rocks to granite batholiths. A Carboniferous overlay of continental and shallow, drying sea types covers the earlier developed complex. Local basins in these times were filled with products of the erosion of tl1e earlier rocks, and, locally, grew the right kind of vegetation to make thin, discontinuons seams and pockets of coal. Post-early Pennsylvanian history is one of erosion and pene-planation with renewal of movement along many of the older fault systems."

Jan 1, 1960

By G. Hamel

The LCL&L process (Low Caustic Leaching & Liming) is a patented hydrometallurgical route developed by Rio Tinto Alcan (RTA) to economically process spent pot lining (SPL) generated by aluminum cells. The three resulting end-products (carbonaceous, fluorinated and caustic liquor) are inert and have valorization possibilities. An industrial size pilot plant located in Saguenay (Quebec) was inaugurated in mid-2008 to demonstrate and optimize the technology. This paper describes characteristics of the LCL&L process and the experience acquired by RTA since the plant's start-up, including ramp-up capacity and technology challenges that were overcome. Possible end-products valorization methods are also presented. The carbonaceous end-product can be separated into carbon and brick rich fractions and used as either alternative fuel, reducing agents, or as raw material for third party processes. The development of a conversion process for the fluorinated end-product would allow its reuse as a substitute to fluorspar mineral for aluminum fluoride production. Finally concentrated caustic liquor is already valorized at the nearby RTA Vaudreuil alumina refinery.

Jan 1, 2011

By Maurice Lauzon

"Aerial surveys of the open pits have been conducted regularly at Lake Asbestos of Quebec, Ltd. -a subsidiary of American Smelting and Re-fining Company -since 1958. Ground controls are supplied by Lake Asbestos, and a topographic map of the pits at a scale of 1 in. to 50 ft., with 2-foot contour intervals, is obtained by aerial photography. The information from the topographic map is then transferred by the Lake Asbestos engineering staff to sections from which the volumes removed are calculated. Considering the size and complexity of the operation, this system has proved to be the cheapest, fastest and most accurate way of determining the quantities of rock and overburden removed. More than 11,000,000 tons of ore and waste are mined each year in three different pits. Further-more, the nature, shape and extent of the orebodies make it necessary to mine on many (up to eight) benches of a pit during a single year. In addition, there are sections of the pits where it is impossible or un-safe to survey the crest of some benches by standard ground methods. For these reasons, the tonnages obtained by truck count are checked and adjusted by aerial survey. These surveys are now taking place every six months. With this system, it is possible for a two-man surveying crew to look after all field work in the mine area."

Jan 1, 1967

By A. Rousselet, H. Gilbert-Tremblay, A. Berton

"Robex Resources interrupted production at the Nampala Mine in September 2014 following throughput and gold recovery results which were below expectations during the first months of operation. After a thorough plant audit, an important brainstorming took place in order to identify an economical path to resume production. It was clearly identified that a significant investment was necessary at the concentrator prior to restarting the plant, namely the addition of a ball mill and a new elution system.The mineral processing simulation software USIM PAC was used in order to simulate the grinding circuit in design. The simulations’ outputs allowed the ball mill characteristics and the surrounding classification devices to be designed with more accuracy. Many ball mills available from second hand retailers were therefore studied in the simulated circuit. The chosen ball mill, which was in perfect condition, had the advantage of being available for rapid delivery on site.The paper first describes the ball mill sizing method in comparison with the conventional Allis Chalmers method. It then describes the phase 2 concentrator start-up (that took place in 2016) with the commissioning of the ball mill, the classification circuit, the gravity concentration, the four (4) new carbon-in-leach (CIL) tanks, and the Zadra elution system (The phase 1 start-up took place in 2014). It finally provides production data compared to expected simulation data, as commercial production was reached in January 2017.IntroductionDesigning a new concentrator or new equipment within an existing concentrator requires significant efforts to identify possible bottlenecks and their causes (i.e. limiting equipment or sectors) and accurate sizing of major equipment can have a tremendous impact on the economy of the whole project. In the presented case study, the ball mill was the critical equipment and oversizing it could have brought the Capex to a level where the project would not have gone through. Inversely, undersizing the mill could have resulted in lower production and therefore no economic viability for the project once it is in operation.During engineering studies, equipment sizing often relies on a static mass balance and one-by-one sizing of all pieces of equipment. The sizing is then left to the equipment manufacturer or in the case of mills, evaluated with empirical models mostly relying on the Bond equations (Allis Chalmers method) [Rowland and Kjos, 1978]. This methodology shows the disadvantage of not considering interaction between equipment in a mineral processing circuit, especially when recirculation occurs. Also, it has the disadvantage of not using the more advanced grinding models that include the use of the whole particle size distribution as well as phenomenological components by only using limited parameters in the ore particle size distribution (i.e. the P80). This can be explained by the lack of data that sometimes needs to be gathered in order to tune the more advanced models but also by the conservative mindset in mineral concentration engineering which does not always favor the use of process simulation. In many aspects of process engineering, Soutex has demonstrated its affinity to using simulation in order to size equipment with more accuracy, consider process variability, simulate complex systems, and study supply chain management (Berton et al., 2015)."

Jan 1, 2018

By G. Barr

"The Polymetallic Twin Metals Project deposits in Northern Minnesota are being developed by Twin Metals Minnesota. Amongst the flowsheet alternatives being examined at a prefeasibility study level is one involving flotation of a bulk concentrate followed by high temperature autoclaving of the concentrate using the PlatsolTM Process to solubilize all the valuable metals in the concentrate (Cu, Ni, Pt, Pd and Au). Autoclave operating conditions have been established in which recoveries of all the pay metals are in the 92 to 99% range, and the autoclave residence time has been reduced to an hour. The stability of the precious metals in solution after autoclaving has been assessed, as well as the impact of internally recycling process liquors to the feed to the autoclave.INTRODUCTIONPlatinum group metals (PGMs; platinum, palladium, rhodium, ruthenium, iridium and osmium) are traditionally recovered from their ores by production of a high-grade concentrate by flotation and/or gravity concentration followed by smelting of the concentrate. Concentrates are smelted to remove nonsulphide minerals and converted to remove iron and sulphur. The resulting high PGM grade matte is processed hydrometallurgically to leach the base metals, leaving a residue with a very high grade (20-40%) PGM concentrate for final refining to individual PGMs. Due to the complexity of this process and its high capital cost, this process can only be applied economically to high grade PGM ores. Lower grade PGM concentrates might be accepted as copper and nickel concentrates but may not yield attractive payment terms for the PGMs. The mineralized Duluth Gabbro region of Minnesota hosts several low grade base and PGM deposits and Twin Metals Minnesota is working to develop the Twin Metals Project deposits. Earlier studies at both pre-feasibility and feasibility level, by other mining companies, have failed to yield an economically viable project based on the traditional process. It is possible to produce a saleable copper concentrate from these ores, but economic recovery of nickel and PGMs into saleable concentrates proved elusive.In the late 1990’s and early 2000’s the Platsol™ process was developed at SGS in Lakefield, Ontario (at the time Lakefield Research Limited) for the NorthMet deposit (also within the Duluth Gabbro) owned by PolyMet Mining. The process developed was a high temperature chloride-assisted pressure oxidation process capable of dissolving simultaneously the base metals (Cu, Ni, Co, Zn), gold and the PGMs."

Jan 1, 2012

By Ausenco Engineering Canada

"This paper demonstrates the selection of grinding circuit technology for a number of recent projects including discussion of the key drivers and the role of energy efficiency. Decreasing head grades combined with a strong and sustained increase in operating costs has forced miners to examine increased project size, increased equipment capacity and efficiency improvements in order to reduce their unit operating costs and improve overall project economics. Comminution energy consumption, safety and capital cost considerations play a critical role in the success of projects. This paper presents some key guidelines for a successful and cost effective comminution circuit design and includes a case study on three projects, outlining the issues and the drivers which led to the ultimate circuit selection and the critical role that energy efficiency played.INTRODUCTIONComminution circuits for minerals processing are selected based on their suitability and efficiency in reducing run-of-mine ore to the desired feed size for the downstream process. The input material (ore) properties and downstream process requirements are the key determinants and there are standard approaches for each circumstance.The minerals processing industry has been a fast adaptor of efficiency improvements based on increasing capacity of equipment (e.g. trucks, crushers, mills, pumps) but less successful in adapting radically new technologies that disrupt incumbent flowsheets or processes.The installed power of grinding mills has increased linearly over the past 25 years (Meka & Lane, 2010) and pumps and classification equipment have kept pace. The autogenous grinding (AG) and semiautogenous grinding (SAG) mills displaced stage crushing as a dominant method of coarse rock breakage in many applications causing crusher manufactures to increase the capacity of cone crushers to meet the competitive demand.Examples of new comminution technology in the 20th and 21st centuries are the development and adoption of cyclone classification in the 1940s (Newtech, 2016), AG milling in the late 1950s, vertical grinding mills in the 1980s, high pressure grinding rolls (HPGRs) also in the 1980s and ultrafine milling technology in the 1990s (Meka & Lane, 2010)."

Jan 1, 2016

By J. D. Clucas, N. Verbaan, T. Grammatikopoulos, D. B. Dreisinger, C. Forstner, M. Aghamirian

"Search Minerals is currently exploring the Port Hope Simpson (PHS) Rare Earth Element District in southeastern Labrador, Canada. The Foxtrot Rare Earth Element (REE) Project in the PHS District has a 43-101 resource estimate consisting of 3,410,000 tonnes of Indicated Mineral Resources and 5,850,000 tonnes of Inferred Mineral Resources. The indicated and inferred resources contain 1.07% and 0.98% total rare earth element oxide (including yttrium), respectively. The dysprosium and neodymium grades are particularly attractive at 218 ppm Dy2O3 and 1687 ppm Nd2O3 for the indicated resources and 208 ppm Dy2O3 and 1494 ppm Nd2O3 for the inferred resources. The mineralization remains open along strike and at depth and is only one of a number of attractive exploration targets in the Port Hope Simpson area. The REE minerals fergusonite and allanite are present. The ore can be beneficiated by gravity, magnetic separation and flotation to a recovery of +80% for the individual REE. Acid bake and water leaching may be used to extract REE into solution for subsequent purification and recovery. The extraction range for single stage leach tests were 91-96% for Nd, 84-87% for Tm and 92-94 % for Dy with modest acid consumptions. INTRODUCTIONSearch Minerals Inc. (Search) is exploring the 100% owned Port Hope - Simpson District in Labrador, Canada for rare earth elements (REE). This District is approximately 135 km by 12 km in size, and is highly prospective for heavy and light rare earth elements. A total of 11 REE prospects have been discovered in the District to date, including the Foxtrot. In addition, Search is exploring in the 100% owned Henley Harbour region and has joint ventures with Quest Rare Minerals in the Strange Lake region, and with Great Western Minerals Group in the Red Wine complex, all in Labrador. These exploration locations are illustrated in the Figure 1. The focus of this paper is the investigation of the mineralogy and processing of Foxtrot REE materials. The Foxtrot resource falls within the claims held by Search in the Port Hope Simpson REE District. The infrastructure available at Foxtrot is excellent with a deep water port, air strip and road and power infrastructure at Port Hope Simpson. Over $7 Million has been spent to date on exploration and development of the District. The Foxtrot has been explored using prospecting geochemical methods, geophysics (airborne and ground), channel sampling of surface outcrops, mapping and three phases of drilling (18,934 m total)."

Jan 1, 2012

By F. L. Wu

Based on the analysis of a sealed coal mine resulting from a fire-triggered explosion, limitations were discovered in the re-entry procedures used to reduce the size of the sealed area that were being applied during the process of re-opening the mine. The analysis of two re-opening plans in a mine using mechanical ventilation showed that the estimation of the degree of damage of two air doors close to the working face with the fire was key to the identification of the optimum mine recovery plan. The operation points of airflow and air pressure of the main fan under either the doors? damaged or intact conditions can be estimated through the use of a ventilation network simulation program. Starting the main fan for a short time period and measuring its operation points of airflow and air pressure allowed their comparison with the simulated values. This procedure provided a reasonable estimation of the degree of damage of the ventilation structures and more confidence in choosing a recovery plan. Through this process, it was possible to conclude that the two doors were still intact. Consequently, the final plan of installing a new main fan in the main decline, sealing the initial upcast shaft and unsealing the auxiliary downcast shaft, was proven to be reasonable at the mine site.

Aug 1, 2013

By K. Jomoto, H. Majima

"Experimental work has been attempted to find a useful criterion of comminution which can be determined simply in a laboratory. The suitability of the ratio of the square of tensile strength to Young's modulus, St2/E, previously derived from the theory of elasticity as a criterion of comminution, was examined measuring tensile strength, Young's modulus and critical height for drop-weight impact of five different rocks. However, satisfactory correlation between St2 /E and critical height has not been obtained, suggesting the necessity of further experimental verification of the representative value of Young's modulus of rocks. The plot of St2 vs. critical height, however, shows one-to-one correspondence, and this finding suggests that St• may be a useful criterion of impact crushing. Also, a close relationship was observed between st• and the energy index for tumbling mill grinding of •the sample rocks. It is confirmed from these findings that the quantity St• is a useful criterion of comminution of rocks, not only for impact crushing but also for tumbling mill grinding. As shown in the experimental part of this paper, the determination ol St with irregularly shaped specimens is simple."

Jan 1, 1972

By S. K. Dimitrov

?Ellatzite Med? is one of the biggest mining companies in Bulgaria, processing about 12,000,000 t of ore per year. Waste materials left after extraction of copper concentrate are deposited in tailings dam ?Benkovski 2?. The hydraulic structure is built according to the downstream method, through hydrocyclonization where the downstream batter and the body of the wall are formed by the separated coarse sand particles of the separated tailings. In connection with the prolonged concession of Ellatzite Med and the enlarged capacity of Benkovski 2, the tailings dam has expanded on to the surrounding terrain. To guarantee a normal hydrocyclonization and build up of a tailings wall during waste deposition from the ore mill, the technological scheme of the hydraulic transport system of Benkovski 2 has been changed.

Aug 1, 2013