Search Documents

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By Mario Gerards, Axel Wellendorf, Arulnesan Rajesh

"In times of increasing energy cost and global demand for improved machine technology, the optimization of industrial mineral processes in terms of efficiency and production cost is an important factor when choosing industrial equipment suppliers. Of course this applies for screening machines, feeders and distributers as well!Besides of the ability of a screening machine for being adjustable to changing requirements during the production process itself, it becomes more and more important to choose the correct screening machine type, peripheral equipment for arising screening tasks and to optimize the overall design of the screening machine starting at a very early stage.The different types of screening machines bring many advantages and disadvantages with them. The selection of the correct type of screening machine can improve the flow rate, energy, efficiency, yield, quality, output, availability and decrease the maintenance costs and structural steel work.The machine optimization has to be a consecutive process in which at any time results of simulation and “real-life measurement” are compared and the findings are implemented in machine development and design. As an example, it is possible to reduce machine weight and reinforce the steel structure of a screening machine at the same time, which enables the manufacturer to use smaller drives for the screen.This paper will present the methods ANSYS and 3D Solid Works used at RHEWUM GmbH for this way of optimizing machine design and construction and examples for results gained from this continuous improvement process."

Jan 1, 2016

By J. E. Nesset, W. Zhang, J. A. Finch

Frother influences water recovery through control of bubble size and a chemical effect. De-coupling the two is necessary to establish the extent of the chemistry effect. A setup is described to give steady state water overflow rate (Jwo) along with measurements of bubble size into and on top of the froth. Arguing neither bubble size correlates directly with water overflow, a frother mass balance is solved to estimate the bubble surface area flux in the overflow (Sb0 ). The solution required measurement of frother concentration using TOC analysis and frother adsorption density using surface tension data. The relationship between Jwo and Sbo reveals the frother chemistry effect, quantified for discussion purposes by an equivalent water layer thickness.

Jan 1, 2009

By P. A. Distin, Jr. da Silva

The history of commercial processes for zirconium/hafnium production and separation is reviewed. A new technology is then proposed as a potential alternative for zirconium/ hafnium separation in a simpler, cleaner way than achieved with current processes. Primary sources of zirconium always contain small amounts of hafnium that must be removed during production of zirconium metal for nuclear applications. This separation is usually carried out by a solvent extraction process, developed in the 1950s, that selectively extracts hafnium, as a thiocyanate complex, using methyl isobutyl ketone (MIBK). Environmental problems inherent to this process are the high aqueous solubility and low flash point of MIBK, and possible gaseous contaminants formation generated by the decomposition of the thiocyanic complexes in hydrochloric acid medium (H2S, HCN, mercaptan’s formation). The present work shows how these problems could be avoided by using organophosphorous extractants that were unavailable when the MIBK process was developed.

Jan 1, 1998

Orebodies of the Renison Bell - Mt. Bischoff tinfield in Tasmania are stratabound, conformable lenses of massive cassiterite-bearing pyrrhotite, with underlying discordant, fault-fracture-controlled and more siliceous ore. The deposits occur in eugeosynclinal, trough-deposited sedimentary and mafic volcanic rocks which are stratigraphically equivalent to diff erentiated volcanic rocks that contain volcanogenic massive base metal sulphide deposits in a parallel arc to the east. Textures of the massive pyrrhotite ore suggest that it has undergone metamorphic recrystallization. Although the massive ore contains both monoclinic and hexagonal pyrrhotite, a study of a few samples from one orebody suggests that their distribution is stratigraphically controlled, with the monoclinic variety abundant only at the base. The distribution pattern of rare-earth elements in massive ore is similar to that of volcanogenic massive base metal sulphides in New Brunswick, and suggests that mixing of sea water with exhalative hydrothermal brines occurred during ore deposition. Tin is a common accessory element in many volcanogenic massive base metal sulphide deposits providing strong evidence that it, too, is transported and deposited by volcanic affiliated hydrothermal brines. Sedimentary rocks containing the massive orebodies are fine grained, thinly laminated, compositionally banded and of mixed chemical sedimentary-tuffaceous origin. They include finely recrystallized chert, carbonate-rich and pyritic varieties; and soft sediment deformation structures in these rocks suggest that dense sulphides deformed underlying, less dense chert prior to lithification. Close to ore the chert becomes massive and coarsely recrystallized, as does the carbonate, which is here strongly enriched in Fe and Mn. Apatite is present in pyritic, cherty and carbonate-rich beds and in the ore itself, in all of which it shows a similar pattern of rare-earth element distribution, suggesting that it is of marine sedimentary origin. These deposits have traditionally been considered as epigenetic replacements of favourable carbonate horizons by hydro thermal flu ids derived from later Devonian porphyritic intrusions. Some of these intrusions have associated tinbearing greisens. The above relationships suggest, alternatively, that, like massive base metal sulphides, the tin deposits were of original syn-sedimentary origin. Circulating hydrothermal brines generated during early Cambrian eugeosynclinal subsidence and tectonism rose through steep fault-fractures, there giving rise to the discordant orebodies, and were discharged on the sea floor, where the massive pyrrhotite lenses were precipitated with the associated cherts and carbonates. In some places, Devonian intrusions remobilized the earlier deposits, forming greisens and newepigenetic veins. Finally , the geologic selling of these deposits, in trough deposited sedimentary and mafic volcanic rocks, suggests another favourable environment for massive sulphide exploration which is quite different from the domal felsic volcanic environment so heavily favoured currently in North America

Jan 1, 1979

By Lloyd H. Yeomans

"This paper will cover recent developments in conveyor applications with specific reference to capacities, bell speeds and distances. It will also discuss certain unique arrangements of horizontal, curved and loop belt systems. In addition, the recent changes in safety factors resulting from new conveyor construction methods will be reviewed.IntroductionConveyor belt systems are currently undergoing dramatic changes. Their use is being extended to providing a viable means for the transportation of bulk material over longer and longer distances.In this paper, a brief account of the historical development' of the belt is outlined, demonstrating how conveyor technology has adapted to changing market demands.Today, energy and environmental requirements are providing what may even be greater challenges. The ability of the belt conveyor to transport material and meet those requirements, places it in the position of replacing many conventional means of bulk material transportation.The paper also outlines some of the progress which has been recently made in this regard and includes a broad approach to the subject of belt design and application.Recent design developments have greatly extended the potential of conveyor belt systems to include applications thought impossible just a few years ago.Graphically illustrating the potential of this new technology IS a belting system currently operating in New Caledonia. Built in 1970, the system has an incredible centre distance of 43,000 ft, or about eight miles.Not to be outdone, the British Coal Board is currently constructing a belt system with a centre distance of 49,000 ft and a speed of 1,650 feet-per-minute. This system is expected to be completed in 1986.These innovative advances contrast dramatically to the conveyor belt's beginnings in the early industrial revolution. Oliver Evans, writing in the 1795 edition of 'Miller's Guide' defined the conveyor belt as a ""broad endless strap of thin pliant leather or canvas, revolving on two pulleys in a case or trough.""Obviously, the conveyor belt has come a long way since those early days."

Jan 1, 1983

By A. Gauthier, J .. E. Muir, M. Cormier

Falconbridge's Lac Shortt gold deposit is located in Gand Township, some 25 km north-east of Desmaraisville, The deposit was outlined in i980 by a drilling program me conducted by Falconbridge Ltd. in a joint venture with Corporation Falconbridge Copper after three years of systematic exploration by Falconbridge Ltd. in the Desmaraisville area. The gold bearing structure had previously been drilled by three other exploration companies. As based on an underground development programme conducted by Corporation Falconbridge Copper, the "in-si tu" mineral inventory to a depth of 500 metres at a cut-off grade of 3.0 g/t is estimated at 1 937 605 tonnes at a grade of 6.4 g/t (uncut) and 6.0 g/t (cut). Regionally, the stratigraphy consists of thick sequences of volcanic and volcanosedimentary rocks intruded by numerous and voluminous mafic (gabbro), felsic (granodiorite, syenite) and anorthositic intrusions. Structurally, at least two fold sets and one major fault system (E-NE) are present. Minor fault systems oriented E-NE and N-NW also occur. Mine stratigraphy can be divided into 1) - the hangingwall; 2) - ore zone; 3) - footwall. Hanging wall rocks include: a) green lapilli and blocky tuff b) transition zone c) green mica crystal tuff and d) red dolomitic tuff. Ore zone rocks include: a) bleached mafic tuff b) barren carbonates, c) pyritic dolomitic tuff (?) and d) brick-red syenite. Footwall rocks include: a) magnetic lava (so-called diorite), b) mafic lapilli and blocky tuff and c) alkali basalt, Native gold is the only gold mineral so far identified and it occurs both as free grains in gangue and as micro-inclusions in pyrite. Two geochemical groups were identified in the main rock units: 1) Alkali-rich rocks cons is ting of the ore zone and foot wall rocks and 2) Subalkaline group consisting of the hanging wall rocks. Ore analysis also shows Ba, Sr, W, Zr, REE and F enrichment in the ore zone. Footwall rocks are enriched in Na20. Present geological and geochemical data do not permit a clear interpretation of the formation for the Lac Shortt gold deposit but suggest it is a volcanic-hosted stratabound type. The bulk of the mineralization is associated with an exhalative phase following alkalic, carbonic, hydrothermal activity and part of the mineralization is associated with a late intrusive phase.

Jan 1, 1984

By Güney

"An investigation carried out to determine the tendency of coals to heat spontaneously in terms of time-temperature curves coupled with the resulting oxidation products in an adiabatically controlled laboratory setup is described. Tests were made at differing moisture conditions, including oxidation and also oxidation with either adsorption or desorption of water vapour on coal.From the experimental evidence, there is reason to believe that the oxidation of coal, although an important factor, is not the predominant one in the development of spontaneous heating. In addition to the temperature increase in coal and the gaseous products evolved due to auto-oxidation, the process is accelerated by adsorption and retarded by desorption of water vapour on coal."

Jan 1, 1971

By Peter M. Power

A microscopic study was made of a series of simultaneous slag and metal samples taken from a low carbon basic open hearth heat. An attempt was made to identify the various micro-constituents found. As the various impurities in the bath are oxidized, the metal structure changes from that of high-phosphorus white cast iron to that of low.-carbon steel. A detailed study of phosphorus distribution is included. The acid run-off slag has an .acicular orthosilicate structure which changes on 'shape-up' to a very basic tri-calcium silicate and calciuim ferrite structure. Many unidentified minor constituents are present in the slags. Though metallography will never replace chemic.al analysis of the bath, the microsopic study of polished slags has some promise of being useful in slag control work.

Jan 1, 1956

By Chris Twigge-Molecey, John Peacey

To meet the business objectives of a metallurgical project, there is often a need for new and untried technology or equipment, whose very novelty can present serious risks to meeting those objectives. The key risk management approach is a rigorous stepwise progression from theoretical evaluations and laboratory tests to pilot plant trials. These must be followed by demonstration-scale trials before final construction of a commercial scale plant, paying particular attention to the magnitude of the scale-up between phases. Success depends on following a well-defined program, not eliminating any steps, and ensuring adequate resources are available to the development team. Chapter 6 discusses the nature of technology risks to metallurgical plant projects, and the rigorous management practices needed to identify, analyze, evaluate, and avoid or mitigate them.

Jan 1, 2015

By Stanley G. Butcher

"Introduction Many operators in western Canada, with a background in the minerals industry, talk of ""coal beneficiation"", whereas the coal industry generally uses the term ""coal preparation"" . The sophisticated cleaning circuits and thermal drying units found in western Canada makes the term beneficiation particularly appropriate. This chapter uses standard coal preparation terminology(l,2J and assumes general knowledge of coal preparation unit processes and equipment(3,4,5). The geologic setting and mining methods of western Canada, described elsewhere in this volume, present for preparation run-of-mine coals which have particular problems. As a result the cost of preparation is a higher proportion of the total minesite production costs than in other coal fields . Preparation requirements are determined by the types of coals being produced and the markets in which they are sold. Western Canadian coals have a low sulphur content and do not require cleaning on this account. Prepared coal from western Canada has to be shipped vast distances -to the Pacific Rim countries and Ontario in particular -and the savings in transport costs justify the high costs of preparation. Factors which dictate selection and operation of the preparation processes are: i) Market specifications and coal rank. ii) Size distribution of particles and particularly the liability of coal and refuse particles to degrade during handling and processing. iii) Quantity and characteristics of the associated refuse. iv) Washability characteristics (the distribution of particles by specific gravity within each size fraction). v) Surface characteristics of the fines. vi) Variability of the raw coal. Where the product (coal or discard) has a high fines content special consideration must be given to dewatering, the removal of surface moisture, to give acceptable handle ability characteristics. In the severe winter climate of the western foothills and mountains thermal drying is necessary to prevent freezing of washed coal in stockpiles and railcars."

Jan 1, 1985

By C. H. Buck, A. J. Taylor

"In 2015 Vale’s Clarabelle Mill began the process change to enable a higher degree of Cu separation. The flowsheet modification was part of a complete divisional flowsheet change being implemented in Vale’s Sudbury Operations. This paper will centre on some of the Operational Readiness (OR) work, culminating in the commissioning of the circuit in March 2017. The emphasis will be on the implementation of an integrated test plan to prepare for the process flow change through the mill.BackgroundClarabelle Mill (CBM) began making a saleable Cu concentrate in 2006 with the installation of the Cu separation circuit. Typical separation rate was 35-40% of Cu in feed reporting to Cu concentrate based on a target Ni concentrate Cu:Ni target of 0.7-0.8. The remainder of the recovered Cu (55-60%) reported to Ni concentrate and was smelted through the Copper Cliff Smelter.In 2013 a capital project, Surface Facility Upgrade (SFU), was implemented to focus on matching the surface plants capacities with the future mine plan to maximize revenues. This was to be achieved by redistributing the metal flow, specifically Cu, through CBM to increase metal unit content through the Smelter. The amount of redistribution of Cu was determined to be based on maintaining a stable Cu to Ni ratio (Cu:Ni) in the Ni concentrate.The change in Cu:Ni ratio in the Ni concentrate would affect the Sudbury divisional flowsheet, and required process changes across the all of the surface plants. The detail that surrounds the flowsheet changes as a whole will not be discussed, but the outcome of the decisions plays a large role in the operational readiness interactions between the mill, its suppliers and its downstream customers."

Jan 1, 2018

By C. J. Newman, R. J. St. Eloi, G. Macfarlane

"The Kidd Creek copper smelter has been expanded from its original design of59000 tonnes of copper per year to over 120 000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and, generally, to optimize the operation.The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates. IntroductionThe Kidd Creek Division of Falconbridge Limited is a base-metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April 1964. Mining operations began in 1966 with a 9000 tonnes per day (t/d) concentrator corning on stream in November of that year. In April 1972, a 108 000 tonnes per year zinc plant was conunissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 t/d of ore. To expand zinc production, the world's second installation of the Commco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 136 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No. 3 tankhouse technology for the copper refinery."

Jan 1, 1994

By Beaumier. M., J. -P. Lalonde

"Les réultats obtenus dans les sols sur quatorze aires d'essai et six cheminements régionaux dans I'A bitibi-Témiscamingue indiquent clairement qu'il existe des variations régionales importantes dans les teneurs en éléments traces de l'horizon A1 formé sur l’épais recouvrement glacio-lacustre de cette région. Les anomalies obtenues correspondent à celles qui ont été décelées lors de précédents levés des eaux souterraines et du till de base.Selon les critères d'évaluation utilisés, treize des quatorze aires d'essai ressortent comme anomales dans Ie contexte abitibien; dix de celles-ci sont tres anomales. Ceci suggère fortement qu'un levé régional de sols, fondé sur une approche multi-éléments, identifierait entre 70 et 90 % des cibles géochimiques reconnues par des échantillonnages en profondeur. Les résultats d'un échantillonnage systématique effectué sur une région de 1000km2 viennent aussi appuyer cette hypothèse. Conséquemment, les sols formes sur les sédiments glacio-lacustres sont un médium très utile pour inventorier de grandes regions recouvertes par ce typ e de sédiments.L 'horizon A1 est Ie plus utile pour ce type de levé parce qu'i1 est facil e d échantillonner, qu 'it assure une plus grande constance du typ e de matériel échantillonne et qu'il contient des teneurs accrues.De multiples mécanismes de dispersion géochimique ont joué des rôles d 'importance variable pendant et après la mise en place des sédiments glacio-Iacustres. Les plus importants sont la pression hydrostatique, la diffusion chimique et électrochimique ainsi que la bio-accumulation. Si on veut progresser dans la connaissance de ce milieu complexe, on devra adopter une approche plus systemique tenant compte de I'interaction des mécanismes agissant dans l'environnement global avant, durant et apres Ie depôt du mort-terrain."

Jan 1, 1984

By Guangdong Institute of Resources Comprehensive Utilization, Y. H. Tang, H. X. Hu, T. S. Dong, Z. H. Zhang

"A world class rare metals ore deposit in Africa belongs to a massive granite type poly-metallic pyrochlore-niobium resource. Successful project development in realizing the resource is vital to Africa’s economy and pyrochlore processing technology.The ore properties are quite complex due to the presence of varieties of valuable minerals, fine dissemination and intimate association of minerals and the relative abundance of easy-floatable minerals. The separation of pyrochlore from zircon, calcite and mica is generally considered difficult. Whilst studies have previously been conducted by several independent institutions overseas, no satisfactory process has yet been developed to date for the ore deposit—possibly due to the process designed being too complex; high cost of regents; lower performance.Based on process mineralogy study and extensive testwork, the authors have in recent years developed a new technology—“De-slime—Iron-rejection—Zircon (with calcite) and Calcite reverse flotation—Pyrochlore flotation”. The flow-sheet is characterized by ?1prior removal of slimes and iron minerals; ?2 Zircon (with calcite) and Calcite reverse flotation; and ?3Pyrochlore flotation applying new type of chelating collector GYX3 developed by GZRINM in conjunction with selected regulators and depressants.The process involved in the new technology is simple to implement and facilitates stable operation; the flotation reagent regime is easily adaptable; the cost of main reagent is lower largely because it is easy to manufacture and is environmental friendly. Laboratory test results demonstrated that, for raw ore assaying 0.35% Nb2O5, 0.03% Ta2O5 and 0.45% ZrO2, pyrochlore concentrate grade of >35% Nb2O5 could be obtained with >74% recovery. Meanwhile, the Ta2O5 content in pyrochlore concentrate could be recycled, and ZrO2 recovery >50% could be achieved in zircon concentrate assaying ZrO2>63%—significantly improving the technical-economic indicator. These results were verified in pilot trials of 1.44t/d throughput. The paper presents the new technology in whole, summarizes the key factors affecting its performance and discusses in simple terms the mechanism of separation."

Jan 1, 2016

By Longjiang Li, Song Mao, Zhengyang Qiao, Qin Zhang, Guizhou University, Ling Wang

"After a study on the advantages and disadvantages of flotation column, according to the limitation of ordinary flotation column only is used for a flotation of microgranular minerals, the paper designed a new kind of layered convection coarse particle flotation column.Using a bauxite to test the rationality of the flotation column.The test results show that the new layered convection coarse particle flotation column is feasible.It has certain advantages about coarse particles flotation.INTRODUCTIONFlotation column has many advantages, for example,a simple structure, high efficiency and energy saving, the obvious advantage of fine particles flotation , the index superior and so on. The advantages gradually getting people's recognition. Research of flotation column has been a breakthrough, however, due to it only is used for the flotation of microgranular minerals, and the microgranular mineral particles will lead to a series of problems, and makes the processing cost is increased. Due to increase grinding fineness can save the grinding time and reduce the cost of grinding, also can avoid the disadvantage of fairly granular mineral particles cause a deterioration in the flotation. So it is necessary to research a kind of coarse particle flotation column.After a research on the advantages and disadvantages of flotation column, the authors designed and manufactured a new layered convection coarse particle flotation column, the flotation column both in theory and operation is better than flotation machine.DESIGN OF THE LAYERED CONVECTION COARSE PARTICLE FLOTATION COLUMNAdvantages and Disadvantages of the Traditional Flotation ColumnIn the field of mineral processing, as the increasing proportion of ore that has low grade, fine dissemination size, complex mineral composition characteristics. The limitations of traditional flotation machine is increasing[1],for instance, the high energy consumption, severe wear, inconvenient configuration , large amount of maintenance and so on. Compared with flotation machine, the flotation column with high separation efficiency, low investment and production cost, covers a less area low installation cost, less reagent dosage, more suitable for separation of fine particles and can automatically control, etc[2]. At present, the ore is facing the world energy crisis situation, and becoming increasingly difficult to flotation. So it is important to invent a coarse particle flotation column."

Jan 1, 2016

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

By Guangdong Institute of Resources Comprehensive Utilization, Y. H. Tang, H. X. Hu, T. S. Dong, Z. H. Zhang

"A world class rare metals ore deposit in Africa belongs to a massive granite type poly-metallic pyrochlore-niobium resource. Successful project development in realizing the resource is vital to Africa’s economy and pyrochlore processing technology.The ore properties are quite complex due to the presence of varieties of valuable minerals, fine dissemination and intimate association of minerals and the relative abundance of easy-floatable minerals. The separation of pyrochlore from zircon, calcite and mica is generally considered difficult. Whilst studies have previously been conducted by several independent institutions overseas, no satisfactory process has yet been developed to date for the ore deposit—possibly due to the process designed being too complex; high cost of regents; lower performance.Based on process mineralogy study and extensive testwork, the authors have in recent years developed a new technology—“De-slime—Iron-rejection—Zircon (with calcite) and Calcite reverse flotation—Pyrochlore flotation”. The flow-sheet is characterized by ?1prior removal of slimes and iron minerals; ?2 Zircon (with calcite) and Calcite reverse flotation; and ?3Pyrochlore flotation applying new type of chelating collector GYX3 developed by GZRINM in conjunction with selected regulators and depressants.The process involved in the new technology is simple to implement and facilitates stable operation; the flotation reagent regime is easily adaptable; the cost of main reagent is lower largely because it is easy to manufacture and is environmental friendly. Laboratory test results demonstrated that, for raw ore assaying 0.35% Nb2O5, 0.03% Ta2O5 and 0.45% ZrO2, pyrochlore concentrate grade of >35% Nb2O5 could be obtained with >74% recovery. Meanwhile, the Ta2O5 content in pyrochlore concentrate could be recycled, and ZrO2 recovery >50% could be achieved in zircon concentrate assaying ZrO2>63%—significantly improving the technical-economic indicator. These results were verified in pilot trials of 1.44t/d throughput. The paper presents the new technology in whole, summarizes the key factors affecting its performance and discusses in simple terms the mechanism of separation."

Jan 1, 2016

By T. Gerritsen, R. MacRosty, R. Pula, P. Gebski, W. L. Ying

Furnace run-outs can cause extended furnace downtime for repair, while leaks or more severe failures in the cooling system can lead to brick hydration or in severe cases, steam explosions. These incidents can result in lost production, damage to equipment, injuries and casualties. To prevent such incidents, reliable and accurate techniques to monitor the critical components of the furnace such as refractory lining, furnace structure, taphole integrity and main water circuits are required. This paper describes several advanced methods that have been developed to assess the condition of furnace integrity, refractory lining, tapholes and cooling water circuits.

Jan 1, 2015

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004