Search Documents

By Dale C. H. Nevison

One of the most intensive of material rivalries is the confrontation between zinc die castings and plastic injection moldings. Pressed hard by the plastics industry, zinc die casters are learning how to make parts with less material yet without sacrificing quality. The key to this new trend is the technique of Thin Wall die casting. The obvious benefits of Thin Wall are lighter weight and lower cost. Again, obviously, these are the very selling points that put plastics into many appliance and automotive parts formerly made of zinc. One of the factors that has been most conducive to the outstanding growth of plastics has been the increasingly prevalent concept that "adequate" properties are sufficient, especially if there are cost advantages. Most of modern design today is oriented around the reasonable life of a product, rather than indefinitely extended life. This is simply an acknowledgment of the existence of a design environment that pervades many areas, reflecting the life-cyclic desire for change. Too often, so-called "weight-saving" materials end up being very costly - not only in production, but in durability and dependability. Change for the sake of change usually doesn't effect a change for the better. In the majority of cases, the best bet is to design in traditional materials and minimize the material needed, while maximizing the efficiency of the production process. Component prices of products to be produced from either plastics or zinc must be studied in detail to determine which material will produce the lowest cost of manufacture. It is not uncommon for two parts, similar in appearance at a casual look, to have a considerable difference in energy requirements and production costs. Detailed cost estimates of the advantages of each material should therefore be prepared for zinc and plastic parts before the final design and material selection decisions are made.

Jan 1, 1978

By K. D. Hester

This paper will review the metallurgical aspects of the completed expansion program at Quirke, and the current rehabilitation and refurbishing program at Panel. During the Quirke program, completed at the end of 1977, the plant capacity was increased from a nominal 4,500 to 7,000 short tons per milling day. The expansion of crushing, grinding, neutral thickening and filtering, leaching, partial neutralization, sand-slime separation, sand washing, C.C.D., clarification, ion exchange, mine water treatment, and tailings neutralization and pumping will be considered. The application of Enviro-Clear thickeners in the mine water treatment circuit and in the C.C.D. will be briefly reviewed. An automatic grinding and classification circuit for limestone will also be covered. The refurbishing program underway at Panel will be discussed. The Quirke and Panel plants will be contrasted and compared. In particular, reference will be made to environmental considerations. The innovative system for producing yellow cake at Panel, LAMIX, will be considered as well as the proposed treatment system for Panel tailings.

Jan 1, 1979

By Peter A. Cain, John C. Folinsbee

"A 4-ft.-diameter shaft has been drilled to a depth of 2,790 ft. in strong, hard, basic Precambrian rocks at Lynn Lake Manitoba. This was done on the property of Sherritt Gordon Mines Limited for the purpose of ventilating and developing the ""N"" orebody, which is located approximately 4,000 ft. south of the Farley shaft.The drilling was done under contract by two drilling companies. Peter Bawden Drilling (1964) Limited drilled the initial 12:1,4-in. pilot hole to a depth of 3,000 ft. Shaft Drillers Limited of Canada then reamed the hole to 4 ft. in diameter to a depth of 2,790 ft. At this point, the reaming was stopped because of the difficulty in passing a change in direction in the line of the pilot hole. The hole was completed by driving a raise 200 ft. from the 3000 level to the bottom of the 4-ft. hole using an Alimak raise climber.Cuttings from the reaming operation were directed into the 12:1,4-in. pilot hole, where they fell to the 3000 level and were removed by a mucking machine and standard mine development cars.The elapsed time from the start of the pilot hole to the completion of the reaming operation was ten months, with an average advance of 279ft. per month. There was a two-month delay between the completion of the pilot hole and the start of the reaming operation.The 12:1,4-in. hole was drilled in an elapsed time of 45 days from the time of setting up the rig. The average advance per day was 66.8 ft.The reaming operation was done in an elapsed time of 194 days. A one-month delay required to repair damaged equipment left 163 days for the drilling and setting-up operation, for an advance per day of 17.1 ft."

Jan 1, 1966

By J E. Curfman

This paper deals with using track-type and rubber-tired machines in the ripping and handling of overburden and ores. The techniques and proper attachments pertaining to the ripping of materials are covered in some detail. Production and relative costs of ripping, as against other methods, are covered in cases pertaining to the mining industry. The use of the refraction seismograph in predetermining the rippability of materials, including a chart relat-ing velocity to rippability, is covered. This operates on the principle that sound waves travel through subsurface materials at different velocities, depending upon the degree of consolidation of the material. It is known that the same factors that affect consolidation also affect rippability. Proper equipping of the tractor to insure maximum efficiency is also covered in some detail. Introduction T HE idea of loosening consolidated materials prior to further handling and processing is probably as old as man. The purpose of ripping is to provide fragmentation of rock and loosening of consolidated materials.

Jan 1, 1965

By Philippe Angers

This article analyzes the social acceptability process of a mining project located in an existing city. It will explore how the principles of sustainable development have been integrated in the project of the Canadian Malartic open pit mine held by the Osisko Mining Corporation, and the corporate social responsibility (CSR) initiatives proposed to strengthen the social acceptability of the project. This mine is located on the ancient south quarter of Malartic and has required the displacement of hundred of houses and five institutions. The location and the inherent social impacts generated by the relocation of the citizens of the south quarter makes this case particularly interesting to understand social dynamics in an era of environmental consciousness. These major constraints of the mine generate high expectations within the urban population with regard to the social and economic benefits it will receive from the project. In a context where society demands higher CSR from the corporation, Osisko is closely followed regarding their actions toward the sustainable development principles to see if they respect the environment and the desires of the community. From the beginning, the company had to be a model of sustainable development in various aspects reflected by the manifold interest of the population. To understand the endeavor made by the company to fulfill the demand of CSR, we will analyze how the company understood sustainable development principles and what CSR initiatives Osisko company put forward. We will explore the involvement of the company in various social aspects like employment, employee satisfaction, and the level of commitment to non-discrimination policy in employment, notably with the native populations. We will also take a closer look at the relationship built by the company with the community and the level of commitment with the various stakeholders of the community. In this way, we will be able to seize the level of involvement of the company in the fulfillment of the principles of sustainable development toward a higher CSR, and to specify the trajectory adopted to build social acceptance.

Aug 1, 2013

By G. B. Langford

UOCK bursts are a phenomenon about which insufficient is known. This l.~ statement has a twofold meaning. In the first place, far too many people, both inside and outside of the mining industry, are woefully ignorant of the whole subject, and secondly, as those who are face to face with the problem in the mines realize, our knowledge of rock bursts is inadequate. The first group embraces the general public, who have never been enlightened on the subject, and a great many geologists and engineers who have never shown more than a curiosity about it. Such technical men do not realize what a vital problem it is to our mining industries. They are usually thankful that bursting ground is not their problem, and leave it to those unfortunate enough to run into it. From such men one often hears the pious opinion that if proper mining methods were used there would be no problem. It is hoped that this paper will give these people a different viewpoint. Those in the second group deserve much credit for what they have done and are doing. They are fighting a large and difficult problem. In the pages that follow, I have tried to give a bird's-eye view of that problem, and suggest new ways in which it may be attacked.

Jan 1, 1941

By S. V. Ulianov, A. Y. Senchenko, E. M. Kurchevskaya

"A process sample of old copper-containing tailings (-2.0+0 mm) from an iron-ore plant was tested in TOMS institute in order to develop a process for copper concentrate production. The study of tailings material composition indicated that -0.2+0 mm fraction was efficient and contained 97.26% of copper. Copper is predominantly concentrated in chalcopyrite which is present both in free form and in intergrowth with ore and rock-forming minerals. Study of chalcopyrite using an optical microscope and Qemscan SEM determined that the most grains surface was covered with oxide films. Additionally, a lot of grains had micropores on their surfaces that indicated a partial mineral leaching. The oxide films did not make it possible to float copper minerals from head material. It was recommended to apply an attrition operation to restore chalcopyrite floatability. In order to increase selectivity a regrinding stage for a primary copper concentrate was introduced to obtain P80 26 um. Taking these recommendations into account a flotation flowsheet was developed to process the old Cu-containing tailings. The flowsheet allowed us to obtain a concentrate with 23.5% Cu content at 71.5% recovery.INTRODUCTIONStudy of material composition is an important prerequisite for development of a minerals processing technology. Mineralogical study contributes to search for an efficient technology to recover valuables and for prospective methods of minerals processing.The use of such up-to-date analysis methods and equipment as Qemscan and Mineral-C7 allows one to determine minerals size, liberation degree, and mineral associations. Mineralogical data can reveal reasons for hard processing of minerals prior to development of the process.The advanced process mineralogical methods used to study Cu-bearing pond tailings indicated several factors that influenced development of the process. The first one is a barren size fraction which is to be removed from the process in order to considerably reduce the costs connected with grinding. The second is the presence of films on chalcopyrite surface; in this context, a preliminary attrition of the material was recommended. The third factor is finely disseminated Cu minerals in sulphide and in the rock, which predetermined selection of particle size for flotation. All these data led to significant decrease in time required to develop the process technology. The developed process flowsheet based on the obtained mineralogical data is present in Figure 1."

Jan 1, 2016

By D. E. Keeley

Introduction Gunite is a mixture of sand and cement applied to any surface by being shot by compressed air through a nozzle, where it is wetted just before leaving the orifice. The mixture is transported through a hose from a machine called a 'cement-gun'(l). Guniting of rock surfaces has been standard practice at the Mcintyre Porcupine Mines, Limited, for several years. Where used on walls and backs of cross-cuts; shaft stations, and other rock openings, as an air seal, gunite has eliminated the necessity of constant scaling to keep rock from falling from these places, and, under worse conditions, it has been used in place of timber supports. This has been of definite help in reducing costs, promoting safety, and minimizing fire hazards. During the past year guniting has been quite extensively used here in the rock head-works of the new internal shaft, No. 12, sunk from the 3,875-foot level. Gunite is at present being applied to the stations of that shaft well below a mile from the surface. This paper describes the method of guniting as carried out at the McIntyre, and illustrates how, by the adoption of this process, mining problems connected with scaling and loose ground have been completely solved. It is hoped that the information presented may stimulate discussion and assist in the use of gunite in this and other mines. The guniting method of applying cement was first developed by Carl E. Akeley (2), Curator of the Field Museum, Chicago, in 1907, and was exhibited in New York at the Cement Show in 1910. The museum was located in one of the old World's Fair buildings, built of roughcast and in bad repair. Mr. Akeley, who was a man of inventive nature, set about devising means of applying cement to repair the walls. The cement-gun was the result. Mr. Akeley was a taxidermist of note, a sculptor, and also the inventor of the Akeley camera. In his work, he was in the habit of using fast setting materials to build up foundations for statues, etc.

Jan 1, 1934

By Reik M. Winkel

Radar Technologies are successful implemented in the military industry since decades and recently found their way in the mining industry as level gauge radars for bin applications. The latest generation of microwave radar sensors are capable to provide geometrical data of the surrounding area of mining machines, too. Radar sensors are an improvement to laser scanners as they are more robust and able to penetrate dust and mist. Radar sensors will be the key source for operator assistance systems. indurad and RWTH Aachen University conducted a large series of tests at open pit mines and underground coal mines to determine the potential of the new two dimensional Dual Range Radar iDRR. Several applications were determined as highly feasible and are now completed respectively in the implementation stage. The authors are giving an insight in the experimental results, the implementation and an outlook of future applications for this technology.

Oct 1, 2009

By W. H. MacLean, P. J. MacGeehan, A. J. Bonenfant

"The Norita deposit is an Archean volcanogenic-exhalative Fe-Zn- Cu sulphide accumulation of the distal type, consisting of six overlapping stratiform massive sulphide lenses, interbedded with exhalative cherts and thin pillow basalt flows, which formed down-topographic-slope from a mineralized hydrothermal discharge zone in the Norita rhyolite. The sulphide lenses are of two main types: channel-fill deposits such as the Main Zone and Main Zone West, composed of intricately layered pyrite-sphalerite-chert, which formed by the dynamic down-slope transport and re-deposition of sulphide exhaled from the vent zone; and stratiform lenses such as the Cu-rich A-Zone and A-Zone West, which formed even farther down-slope, in basinal depressions flanking the dome. Although rotated into a vertical position by folding, the sulphide lenses are otherwise essentially undeformed and contain a wide range of preserved primary sedimentary structures.Of prime importance in exploration has been the recognition that the formation of the distal sulphide lenses was controlled by submarine paleotopography, and that it is possible to approximate the sea-floor paleotopography using variations in the thickness and strike extent of the interbedded volcanic rocks. This has proved to be a major and successful exploration tool in the search for further sulphide mineralization in the mine, and offers prospects for use elsewhere in the district."

Jan 1, 1981

By Laxman M. Amaratunga

Laboratocy flarmnability tests were perfonned on dust samples from Fraser Mine in a 1.2 L Lindenburg horizontal tube furnace to detennine the percentage of sulphur oxidized during ignition. The explosion pot ential of sulphide dusts depends on their degree of spontaneous oxidat ion, which was measured by the quantitative analysis of so2 gas released during ignition. Test results indicated that dusts with low sulphur content could exhibit a higher degree of oxidation than a sample with high sulphur content. txlst characterisation using image analysis techniques suggests that the structure and the texture of dust are important factors influencing the explosibility of sulphide dust at ignition temperatures. Therefore for safe mine operations% sulphur content cannot be considered as a reliable single index that could be used to predict the potential of a sulphide dust explosion. Physical, chemical and mineralogical characterisation of dust plays an important role in the detennination of suitable indices for the prediction and prevention of sulphide ore dust explosions.

May 11, 1988

By W. J. Cherones

This paper describes the history of the development and application of the electric mining shovel in open-pit mining, dea1ing particularly with far-reaching advancements in three primary areas: metallurgy, mechanical design and electrical systems. Hoist drives and crowd drives, including the Magnetorque and Electrotorque systems, and the integral propel drive are given close attention.

Jan 1, 1972

By W. K. A. Congreve

Introduction Less than a hundred years ago the engineer was able to do his job without concern for the science that underlay his practices or for the men who operated his machines. But toward the end of the last century science began to be applied to industry, and its success was such that the plant which clung to empiricism was unable to compete with the plant that followed science. Even more recently, the engineer has been forced to consider the men who operate his machines, for modern large-scale industry has given these men education, social security, and power. Hence the engineer can get good, steady labour to operate his machines only if he can offer inducements. Wages are in general outside the control of the engineer, but he is able to control working conditions. This essay is concerned with one factor of good working conditions: safety. The writer became interested in this problem during three months' summer employment as a student at the Sullivan concentrator of the Consolidated Mining and Smelting Company and was surprised at the distance his investigations led him from the field of pure engineering into the fields of psychology, education, and publicity. Nevertheless, because safety has to do with machines and with men who operate machines, and because it profoundly affects plant efficiency, it is the job of an engineer, not of a psychologist or teacher, nor of the salesman publicity expert who is often so unfortunately employed in personnel relations. The size and complexity of the subject has limited the scope of this essay to the consideration of only a few aspects of industrial safety. Considerable attention has been given to the underlying principles, but the mechanical side of accident prevention, the design of equipment, erection of guards, etc., and the very important problems of organization and administration, have not been given attention proportionate to their importance.

Jan 1, 1948

By M. Peshko, J. C. Gingerich, L. W. Matthews

"Noranda has successfully developed and implemented two leading-edge mineral exploration technologies — hyperspectral remote sensing and 3-D seismic surveying. Airborne hyperspectral imaging provides detailed geological and mineralogical mapping capability at both a regional and project scale that facilitates improved selection of prospective terrain and an accelerated exploration cycle. Noranda, in partnership with Falconbridge, has licensed the exclusive use of the Earth Search Sciences Inc. (ESSI) Probe-1 hyperspectral scanners (128- channel, 0.43 µm to 2.5 µm spectral range) that are capable of mapping in excess of 3500 km2 per day at 10 m pixel resolution. The technology has been successfully deployed on four continents over a broad range of terrain from desert to boreal forest and the high Arctic.To augment the company’s deep search initiatives, Noranda has successfully modified and implemented existing 3-D seismic technology to help targeting massive sulphides located at depths ranging from 500 m to 2000 m. In the fall of 1998 and early 1999, Noranda completed an 18 km2, 3-D seismic program in eastern Canada by successfully drill testing acoustic impedance anomalies locating massive sulphides at depths in excess of 1100 m."

Jan 1, 2002

By L. Dubourg, H. Habibi, D. Rasmussen

The combination of laser welding with Gas Metal Arc Welding (GMA W) forms the hybrid laser-OMA W welding. This process is an attractive tool with a high potential in welding lightweight structures, especially for aluminum alloys. For five years, this technology has increasingly attracted interest in both, industry (aeronautics, automobile, metal industries producing large structures) and academia (universities and research centers). Hybrid laser-OMA W welding process is generally accepted for its robustness, efficiency and flexibility. Coupling of a deep-penetrating laser beam with the heat and molten metal feeding of GMA W significantly expands the original welding application range of lasers. Its main advantages compared to the two individual components are deep and stable weld penetration, gap-bridging ability improvement, low distortion and easy filler metal addition. Hybrid welding allows a much wider groove tolerance compared to laser welding, especially for aluminum welding. Moreover, the reduction in distortion decreases the post-welding rectification needed and makes the assembly easier. In addition, if metallurgical factors are critical, the weld composition can be balanced with filler metal, decreasing the hot cracking susceptibility of some aluminum alloys. The combination of these two welding processes can also improve the weld bead shape quality (including the elimination of undercut), possibly reduce the porosity and increase the welding speed. This article reviews the recent works about the laser-OMA W hybrid welding of aluminum alloys. After a brief presentation on the interaction mechanisms between a laser beam and an electric arc, the paper depicts the typical welding parameters and experimental methods along with their characteristics.

Jan 1, 2006

By R. Blazej

Machinery Systems Division (MSD) in the Institute of Mining Engineering at Wroclaw University of Technology specializes in belt conveying systems analyzing, calculating and design. Within the division operates the certified Laboratory of Belt Transportation (LTT) and Laboratory of Rollers. Since few years, a group of several people have begun work on developing a comprehensive system for the automatic evaluation of condition of conveyor belts working in the mines. Group uses both magnetic devices developed by specialized companies servicing belts and its own machine vision system developed for assessment of belts covers and edges during belt movement (up to 7 m / s) on the specially designed for this purpose the test conveyor. Recently they have got the research grant funded by the National Centre for Research and Development (NCBiR) for development of the system for automatic diagnosing of conveyor belts? condition and aiding of rational belt management. On the basis of previously created diagnostic tool called ABCDE (Automatic Belt Condition Diagnostic Equipment) the five modules: vision-A magnetic-B, preventive-C, forecasting?D, and determining safety factor-E will be developed. They will automatically interpret data about conveyor belts? condition to indicate the extent and timing of repairs, to prevent failures and to select the optimum moments for their replacements. The system will use results of ongoing research & development and planned research concerning modeling of belt wear using evolutionary genetic algorithms. The reached stage of research can not yet allow to start the implementation work by potential users. It is therefore necessary to pursuit research in real scale, the development of new modules (C-E) and intensive testing of the system in working condition with system calibration to optimize the economic effects.

Aug 1, 2013

By L. M. Scovell

The Internet and its related technologies will radically change the way that mines manage and control their maintenance, repair, and operating supply chains. The Internet is creating new distribution channels and offers new technology platforms with significant advantages over more traditional methods. Mines will have to re-evaluate both the strategies and the tactics employed in these areas. Mines will use e-commerce to integrate their maintenance, repair, and operating supply chains. The integration will extend beyond traditional trading partners to a worldwide network of communities with similar interests and goals. The changes will transform the way mines operate, lower mining costs, and thereby increase their chances of success in an increasingly competitive environment.

Jan 1, 2000

By M. Imani, A. Fahimifar, A. H. Javid

"Current studies of bearing capacity for shallow foundations tend to rely on the hypothesis of an isolated footing. In practice a footing is never isolated; it is mostly in interaction with other footings. This paper focuses on a numerical study to evaluate the ultimate bearing capacity for two interfering strip footings resting on a rock mass in which the strength can be described by the generalised Hoek–Brown failure criterion. This criterion is applicable to intact rock or heavily jointed rock masses that can be considered homogeneous and isotropic.The material is assumed to exhibit perfect plasticity and obeys an associated flow rule. The effects of Hoek–Brown parameters including GSI, mi, and sci were studied and the corresponding results are presented. For different clear spacing (S) between the footings, values of the efficiency factor (?) were determined; where ? is defined as the ratio of the failure load for an interfering new footing of a given width (B) to that of a single isolated footing having the same width. The maximum value of (?) occurs at spaced between S/B = 0.5 to 1.0. The results have been compared with those available in the literature.INTRODUCTIONEvaluating the ultimate bearing capacity of rock masses is essential for important projects like dams and bridges. Closely spaced footings may occur on rock masses in the form of pier foundation and grillage footing. Close spacing lead to permit higher loads than can be bore by similar isolated footings. The ultimate bearing capacity of two interfering strip footings resting on cohesionless soil have been studied theoretically (Kumar, & Gosh, 2007; Kumar, & Kouzer, 2008; Stuart, 1962). Results revealed when two strip footings approached closely enough, failure zones affect each other and ultimate bearing capacity significantly increased."

Jan 1, 2015

By F. Daniel Rosenkranz, Peter L. Silveston

Experiments investigating the treatment of a ground wood white water waste from an Ontario pulp and paper mill by an HVCB coal are reported. Adsorption capacity for the waste, with a soluble COD contribution of 2,100 mg/I, amounted to 0.17 per cent, by weight, of the Nova Scotia coal used. Percolation of the white water waste through a coal bed indicated that soluble COD is removed. For finely ground coals, over 90 per cent of the suspended solids in the waste are retained on the coal. Plugging of the coal bed is rapid, so that any treating process using filtration would have to renew the surface of the bed frequently.

Jan 1, 1970

By F. Channier

The paper provides the most recent information on the construction of the AP60 phase 1 plant of Jonquiere which is due to be commissioned and started up in the first quarter of 2013. HSE management on site by RTA, and cooperation with local equipment manufacturers and contractors of the Saguenay-Lac Saint Jean region are highlighted in this section. The AP60 phase 1 Jonquiere plant aims to demonstrate of the AP60 technology at an industrial scale and allows the further developments of the AP60 cell. The advantages of the AP60 cell technology in terms of productivity, power consumption and environmental footprint are also briefly presented in the paper.

Jan 1, 2011