Search Documents

By Denis Thibodeau

The selected mining method for the Rodeo lower Zone is slot and slash. Initial design indicated that the stope height should be limited to a maximum of 18 m, thus six levels were needed to extract the ore. Higher stope height in the Rodeo Lower Zone means less development thus less capital required to extract the available reserves. It was proposed to eliminate one level by establishing 30 m and 24 m level intervals. To ensure that no stability problems will be encountered by eliminating one level, a Matthew analysis, based on diamond drill core information, was performed for the Lower Rodeo Ore Body. In addition, comparisons between the rock mass quality of Meikle Main Zone below 1825 L and Meikle East Zone between 1600 L and 1750 L with the rock mass quality of the Lower Rodeo were made

May 1, 2002

By Baoquan An

The energy required to fragment a rock is proportional to the increase in the fracture surface area and hence is proportional to the rock?s surface area. In comminution, the slope of the linear relationship between size reduction ratio and specific energy is usually defined as grindability. Another definition of grindability based on newly created specific surface area and specific energy is introduced. The two definitions for grindability reflect the grindability properties of rocks and can be used to measure of the efficiency of mills or crushers. The feed particle size distribution influences the energy needed to comminute the rock. For a given ratio of average feed size to product size, the smaller feed size requires more energy.

May 1, 2004

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By Chuck Edwards

Whatever your opinion of the validity of the scientific case for global warming, or of the wisdom of the Kyoto Protocol, it would seem judicious to err on the side of caution and try to sensibly minimize global climate change. To this end, we should take prudent steps to minimize our emission of greenhouse gases. Cameco is the world's leading supplier of uranium for use as fuel in nuclear power plants. Cameco’s uranium production fuels nuclear power plants in 16 countries. Nuclear power plants generate clean electricity without greenhouse gas emissions. This presentation describes the role that uranium and nuclear power can have in meeting the growing demand for electricity and at the same time combating global climate change.

Jan 1, 2004

By T. B. Armstrong

"The developing world energy crisis and spiraling fuel costs have created a new public awareness and general acceptance of the need for energy conservation.Plants will have different objectives for an energy conservation program but there appears to be a common approach on how to save electrical energy.Data for a 180tph Rod Mill powered by a 750 hp motor will be used to demonstrate the relationship of energy input and production levels and to seek an optimum operating condition.Energy Conservation:Plants that have examined ways of dealing with the energy situations have concluded that energy conservation has important benefits for industry, including reduced costs, fewer production slowdowns inthe event of fuel shortages and a continued competitive position.There have been some ""startling"" conservation achievements attained through such simple plant maintenance and operating practices as reducing unnecessary lighting in buildings and yards, turning off' equipment not needed at night or over week-ends, through planning maintenance and production schedules to minimize energy use and through improving quality control to eliminate waste.Significant reducti.ons in energy use have been achieved by some rather simple but vigorous maintenance and plant engineering efforts directed at finding and fixing energy ""leaks"" rather than technological advances or major rework or redesign of facilities and equipment.An Energy Conservation Program often must overcome such obstacles as historic operating practices and emp1-oyee indifference, i.e. the ris.ing costs of fuel should result in re-examination of so1ne basic attitudes to energy conservation. Some measures, rejected in the past largely on the grounds of capj.tal. expenditure, now make economic sense in the light of future escalating energy costs."

Jan 1, 1978

By Dina M. Aloi

In today?s evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to ?engage? communities without a clear understanding of ?how? to do this or to what end. This move, away from compliance, develops more of a focus on ?Community? Social Responsibility and sustainability. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of ?engaging? communities in mining project design and development leads to a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be ?engaged? in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this ?engagement? and manage this risk will be discussed.

May 1, 2007

By Yum Xiaoquan, Turgut Yalcin

"A laboratory study was carried out to determine the potential role and effect of ultrasonic irradiation in the flotation of a Sudbury copper-nickel sulphide ore. The use of ultrasound was tested separately at the pulp preconditioning, collector conditioning and flotation stages. While no significant benefits were evident in the latter two cases, ultrasonic preconditioning of pulp improved the grade-recovery performance and had the prospect of reducing reagent consumption rates. Tests were conducted on both the normal and oxidized ore samples, and several variables were investigated, including ultrasound frequency (25 kHz and 45 kHz), ultrasonic power (up to 1.6 W/cm2), duration of ultrasonic treatment (up to 60 minutes), and the intensity of pulp agitation employed during the application of ultrasound. Ultrasound frequency of 25 kHz and duration of 15 minutes yielded satisfactory results. Changes were found to occur in the temperature, pH and Eh of the pulp during ultrasonic processing. The favorable effects of ultrasound observed in this study were attributed primarily to its surface cleaning capability.INTRODUCTIONThe use of ultrasound for the surface cleaning of objects is well known. Ore flotation is based essentially on the surface properties of minerals, and hence stands to benefit from ultrasonic treatment which may help restore mineral surface characteristics that might have been lost or modified through oxidation, etc. Expected outcomes of this method of treatment include improved flotation kinetics, higher recovery, better selectivity, and savings in reagent consumption, as has been demonstrated by various researchers (Aldrich and Feng 1999, Celik 1989, Ozkan 2002, Letmathe et al. 2002, Nicol et al. 1986)."

Jan 1, 2005

By Charles Kocsis

Over the last few years a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell powered equipment into underground mines to replaced diesel engine powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine?s energy consumption, its associated greenhouse gas impact and also reduce a mine?s significant ventilation associated costs. Fuel cell powered equipment also has the advantage of lower noise and heat production compared to their equivalent diesel powered counterpart. The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions and minimum velocity requirements. However another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations these factors change, dispersion and buoyancy are limited; time may not be available and in non-coal mines ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical, consequently ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation such as a hydrogen leak from the fuel cell stack or its distribution system.

May 1, 2007

By Derek J. Cyr

Climate has an immense impact on the properties of Athabasca oil sands and the ease or difficulty with which it is excavated and extracted. During the winter months, exposed oil sands surfaces freeze. When hydraulic and electric shovels used in the various operations in the Fort McMurray area excavate the benches, large frozen lumps are created. These lumps are either destined for a lump dump where increased costs are incurred due to rehandle, or they are sent to the primary crushers where they can cause significant downtimes by jamming the crusher. The crusher down time can sometimes be in the order of hours of lost production. Studies on data from two consecutive winters at Syncrude Canada?s North Mine show a high correlation between climate and the generation of frozen oil sands lumps. Temperature, ground cover, traffic, bench exposure time, oil sands grade and moisture content all contribute to this problem. A 1D frost penetration model was used to predict the depth of frost expected in oil sands and the corresponding likelihood of frozen oil sands lumps. To combat the challenge of frozen lump generation, a number of proactive and reactive measures can be taken: artificial snow, shallow ponds, scheduling, blasting or ripping.

May 1, 2004

By Manqiu Xu, Peter Wells, Gord Bacon

"A methodology is proposed for milling flowsheet design using flotation rate, selectivity and residence time distribution data. The flotation rate data and the difference in flotation rates between the main minerals to be separated are determined from laboratory batch tests. The residence time distribution (RTD) data is calculated using the tanks-in-series model assuming each flotation cell is a perfect reactor. The rate, selectivity and RTD data can be used to calculate the optimum flotation cell number in a bank for rougher/scavenger in a commercial plant.This methodology is demonstrated in a case study of a nickel sulfide ore. It is shown that miniplant rougher/scavenger data can be closely predicted from a batch test using the proposed methodology.INTRODUCTIONIt has been the trend in the past several decades that large flotation cells are increasingly used. This is largely driven by the economics as ore grades are getting lower and the rate of ore processing must be increased in order to keep mining operations economically viable. The development and evaluation of 250 to 500 m3 WEMCO SmartCell and Outokumpu TankCell flotation machines are well in progress. There are many advantages in using large cells: fewer cells, less floor space, lower power cost (although this is now being questioned for fine particle flotation), simpler circuit, simpler control, and lower auxiliary equipment cost (Arbiter, 1999). As flotation cells are getting larger, the importance of cell hydrodynamics, namely, air/slurry dispersion, power intensity, froth transfer, residence time distribution (RTD) and short-circuiting are being fully recognized (Jonaitis, 1999; Weber, et al., 1999; Gomez and Finch, 2002). It is not the intention of this paper to discuss flotation cell scale-up. The intention is to answer what is the optimum number and size of cells in a flotation bank for a given throughput. Figure 1 illustrates this problem facing design engineers. The same mean residence time required for a given throughput can be achieved in a single large cell, or many smaller cells in a row. A few cells of large size may be more cost-effective but they may not be as effective as more cells of smaller size in achieving the optimum metallurgy."

Jan 1, 2005

By Charles "Chick" Rodgers

"The Key Lake uranium mine is the largest single uranium producer in the world. It is owned 2/3 by Cameco Corporation and 1/3 by Uranerz Exploration and Mining. Cameco is the operator. Current production is fourteen million pounds per year of uranium oxide (U308).The mine's location is 570 kilometres north of Saskatoon on the southern edge of the Athabasca Basin approximately at latitude 57° 11 'north and longitude 105° 34' west. Access to the mine is by an all-weather road and a private airstrip.The mill was commissioned in 1983. A molybdenum plant was constructed in 1989 in response to increasing molybdenum content in the yellowcake or final product. Early test work had showed that the first ore body to be mined, the Gaertner deposit, would present few problems with regards to molybdenum in the product. However, the test work also showed that the higher molybdenum content of the Deilmann ore, the second Key Lake orebody to be mined, would result in increased molybdenum concentrations. Without the molybdenum plant, penalties would become excessive and some product might not accepted by the refineries.This paper will describe the current Key Lake mill process with emphasis on the molybdenum solvent extraction process. It will cover the chemistry of the process, process development in the mid 1980's, and current operating practices.The Key Lake milling process consists of five individual plants, crushing and grinding, leaching -counter current decantation (CCD), solvent extraction, yellowcake/crystallization and bulk neutralization (Figure 1. Simplified Mill Flowsheet). A detailed mill flowsheet can be found in the appendix."

Jan 1, 1996

By Z. D. Hora

"There has been a number of new developments in British Columbia's industrial minerals field over the past few years. Several new industrial operations were started to diversify the line of British Columbia mineral production by magnesite, perlite and fuller's earth. Industry activities and geological projects have identified occurrences of rare earth minerals, niobium, kaoline, fireclay and zeolites. The Geological Survey Branch significantly improved its database on industrial minerals. New geological concepts based on recent work are opening a number of new opportunities f or further industrial minerals' exploration and development in British Columbia.IntroductionTraditionally, the value of industrial minerals produced in British Columbia in any given year comprises between 100/0and 15% of the combined value of minerals, coal, petroleum and natural gas. Over the years a wide variety of industrial minerals has been produced , often with different levels of marketings success. For some products, such as dimension stone and clay or shale products, initial strong demand gradually dissipated; for others such as asbestos and magnesite, new discoveries or new industrial activities created demand and new markets . In some cases, such as fluorite , talc, pyrophyllite and perlite, wider use has been prevented by small size, poor quality or remote location of the deposits. Also, British Columbia , with 2.6 million inhabitant s, provides only a limited market and the industry therefore has to look beyond provincial borders."

Jan 1, 1990

By Baki Özüm

Early evaluations of Pasquia Hills kerogen shale deposits by Geological Survey of Canada, Saskatchewan Geological Survey, Manitoba Energy and Mines and Sun Oil Company, using modified Fischer Assay, Rock-Eval and other techniques, estimated recoverable reserves of about 2.6x109 barrels of oil in areas favorable for strip-mining; each metric ton of ore was determined to yield about 30 L to 50 L of shale oil remarkably high in aromatic compounds. Western Petrochemical Corp. (WPC) is holding two Oil Shale Exploration Permits covering about 76,635 hectares in the Pasquia Hills Region of eastern Saskatchewan and conducting a 15-corehole drilling program to determine stratigraphic correlation on both first and second white specks kerogen shale. In this program, correlation will be established between oil yield and oil quality, using different retort techniques, including modified Fischer Assay, steam retort and Rock-Eval. Results will lead to further resource evaluation and to a preliminary engineering design for a shale processing plant, including selection of retort process, upgrading of shale oil to petrochemical feedstock, hydrogen management, energy balance and evaluation of environmental impact.

May 1, 2002

By Richard Jundis

At the Vale Inco Ontario Operations, the working environment is rapidly evolving with organizational changes, new business systems and software tools. These changes are required in order to meet today?s challenging business environment. Mining professionals are focusing on the development of safe and achievable mine plans to maximize mining value while reducing the potential of project delays and production shortfalls. This paper explores how new design tools, techniques and system designs in mine planning are being developed to optimize the value of every ton of ore mined and processed. To differentiate from other papers on long-term planning, this paper focuses on the concept of business planning at the mines. Business planning is the understanding and optimization of the relationship between mine plans and the value it adds in the overall process. The management and key stakeholders of Vale Inco have recognized that the development of a robust mine planning system and programs are essential for the long-term sustainability of the operations.

May 1, 2009

By Marc C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuelcell vehicles, a broadscoped project was initiated to quantify the costs associated with operating fuelcell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This article outlines the results of the investigations to date defining the costs/benefits associated with: capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment and infrastructure savings are possible with the application of fuelcells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuelcell mining equipment is currently higher than diesel versions, the high cost of fuelcells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case the operational savings would probably be sufficient to balance the supplementary capitalization costs. A comprehensive cost-benefit report will be issued in the near future.

May 1, 2003

By F. Hassani, R. Mikaeil, B. Ferdowsi

Two analytical solutions for estimating the ovaling deformation and forces in circular tunnels are widely used in engineering practice, due to soil-structure interaction under seismic loading. This paper discusses the discrepancy between the two analytical and finite difference methods. A comparison of the two analytical methods shows that the calculated forces and displacements are identical for the condition of full-slip between the tunnel lining and ground. However, the calculated lining thrusts differ by an order of magnitude when considering no-slip between the tunnel lining and the ground. The analytical solutions are compared to numerical analyses of the no-slip condition using the finite difference method to validate which of the two methods provide the correct method. To achieve the goal, numerical modelling, field data of the Kuhin railway tunnel and Manjil earthquake characteristics are used. Numerical analysis results agree with one of the analytical solutions that provides a higher estimate of the thrust on the tunnel lining, thus highlighting the limitation of the other analytical solution.

Jan 1, 2008

By Elizabeth Gardiner

Tailings and water management facilities are integral components of mine and mill operations. They must be managed for the long term to ensure that safe and environmentally responsible stewardship is achieved. The Mining Association of Canada (MAC) has developed and published two manuals to provide guidance to mining companies on sound practices for the safe and environmentally responsible management of tailings facilities: ???A Guide to the Management of Tailings Facilities; and ???Developing an Operation, Maintenance and Surveillance Manual for Tailings and Water Management Facilities. The Guides were designed to help companies develop and implement tailings management systems that include environmental and safety criteria, to improve the consistency of application of sound engineering and management principles to tailings and water management facilities through their full life cycle, and to demonstrate this to regulators and the public.

May 1, 2003

By Denis Thibodeau

his paper describes a study of an altered mining extraction and the resulting Rockmass response at VALE?s Creighton Mine. Typically, the deep mining zones have strict stope extraction guidelines to ensure safety and productivity; however, these guidelines offer low flexibility or few options for stope sequencing. The 402 O. B. being in a good rock mass, at moderate depth and stress regime at Creighton, offered an opportunity to drive a more flexible mining sequence with stopes and a pillar. A three-phased approach was used to mitigate risk of the mining plan: 1- Numerical modelling to fully anticipate rock mass response to the proposed mining sequences. 2- In situ seismic monitoring to collect stress and seismic activity data. 3- Analysis of the in situ data to correlate to the modelling results. The creation and the extraction of a pillar in the 402 O. B. was successfully completed. The recorded seismic activity agrees well with the numerical modelling since most of the seismic activity is localised in the hangingwall where the deviatoric stress corresponds to an early damage process. The moderate levels of deviatoric stress cause localised failure with low level of seismic activity.

May 1, 2013

By Patrick F. R. Murphy

An ultra-low profile LHD has been developed by EJC Mining Equipment of Burlington, Ontario for narrow-reef mining applications. This paper discusses the challenges encountered during the evolution of the machine's design and subsequent field testing. Continuing research and development focuses on optimizing machine performance and controllability, reducing emissions, and enhancing maintainability. Details will be given on field trial experience and ongoing test work being carried out at the manufacturing facility.

May 1, 2004

By V. Murugaiyan

The Geotechnical Engineer is faced to view problems emerging from the task of protecting the environment and also the problems related to prevention of natural hazarders. Geo-Environmental Engineering, based on the development of geotechnical engineering, addresses the problems for the industrial world and the impact on health and welfare in relation to pollution of the ground. In the recent years, acute land pollution due to indiscriminate discharge of industrial effluents especially Organic acid based effluents has become one of the major concern due to erosion in the privatization of sustainable development under Indian Scenario. To study the effect of chemical changes on soil properties due to amino acid effluent contamination on soil and erosion behavoiur. The changes in the soil properties of effluent contaminated clay and silty soil were experimentally observed to be due to the interaction of organic and inorganic constituents of effluent on index properties of soil. The surface reactivity of soil mass is experimentally reported to be varying proportionately with respect to clay (%) in the soil. Also higher surface reactivity of clay increases the Solid Retension Time (SRT) with increase in rate of chemical transformation of organic and inorganic solids within soil. Hence soil S1 (high clay content 54.5%) showed increased SRT and soil S3 (low clay content, high silt and clay content 94.9%) showed decreased SRT and long transformation stage.

May 1, 2004