Search Documents

It has become increasingly clear in recent years that human kind has developed the capacity to alter the environment of the Earth on a global scale. The changes are often subtle. This is particularly true in the case of stratospheric ozone. Ozone is produced primarily in the stratosphere, at altitudes in excess of 20 km, initially through the action of ultraviolet sunlight dissociating molecular oxygen. According to theory as it existed up to a few years ago, ozone is removed mainly by reaction with atomic oxygen. In the unperturbed environment, this reaction proceeds both directly, and by paths catalyzed by trace quantities of nitrogen radicals. Molina and Rowland [Nature, 249, 810, 1974] pointed out that decomposition of industrial chloroflurocarbons could in-troduce an additional source of radicals to the strato-sphere. Chlorine radicals are even more efficient than nitrogen in catalyzing recombination of oxygen atoms with ozone; models suggested that we might expect reductions in the vertical column density of ozone of as much as a few per cent over the next several decades. A reduction in ozone of x¦/a, by increasing the flux of ultraviolet sunlight reaching the surface, was predicted to result in an increase of about 2x% in the number of cases of skin cancer, with other less well defined impacts on the non-human environment for life.

Jan 1, 1990

By Forssberg E

This paper presents the experimental results on the effects of slurry Theology on ultra-fine grinding by a stirred ball mill. The amount of dispersant, slurry density and the particle size were selected as the parameters. The viscosity of dolomite-water slurry was measured by rotational viscometers. It was found that by adding enough dispersant, the effect of particle size from 1 to 10 pm on the slurry theology could be eliminated, but a strong effect of slurry density (tested for a range of 65 to 75 wt per cent) remained. The use of dispersant transformed the slurry from Bingham plastic flow to dilatant flow, which reduced the yield stress to zero, but increased the viscosity at higher shear rates. During the milling process, the viscosity was stable. The yield stress, however, increased suddenly from zero after a certain milling time. The mill operation stopped at the point where the yield stress increased due to poor slurry fluidity. The milling efficiency was found to be higher at a lower amount of dispersant addition or a lower slurry density within the experimental limits.

Jan 1, 1993

Uranium minerals were found in Australia as early as 1869, but it was not until the 1940's that a search specifically for uranium was begun. Instrument types and techniques used in early exploration are still used today, but have been developed into more sophisticated and portable types. Recent improvements in exploration have been the introduction of the gamma ray spectrometer, radon sampling and geochemical surveys. The environments of presently defined uranium deposits are predominantly sedimentary. Known deposits in igneous environments are usually small. The size of targets which are likely to provide economic deposits is of the order of 10,000 tons U308, producible at a cost of less than $10 per pound. Such targets are most likely to be in Precambrian sediments or in granitic masses. Recent exploration in Australia has included investigation of Precambrian sediments, Precambrian and Palaeozoic granites, Mesozoic and Tertiary sediments, Precambrian volcanic rocks and brecciated masses of unknown age. The origin and method of emplacement of uranium in these environments is not well known but there are indications that syngenetic sedimentary processes are important, and volcanic rocks may make a major contribution to the supply of uranium.

Jan 1, 1970

Cyanidation tests by bottle agitation were conducted on an oxidized lead-silver ore containing approximately 12% Pb and 500 g/t Ag. Over 60% of the silver was leached when the ore was ground to 100% passing 0.15mm, whereas 50-60% of the silver was leached when the ore was only ground to 100% passing 0.5mm. Slurry handling and dewatering at the fine grind size were very difficult due to the high clay content of the ore, however this problem was greatly reduced at the coar- ser grind size. The silver recovery at the fine grind size was very dependent on cyanide solution strength with stronger cyanide sol- utions (containing more than 0.1% NaCN) re- sulting in lower solution silver contents. This was thought to be due to the precipi- tation of leached silver by zinc, which was also leached from the ore by the higher cyanide levels. There was a critical zinc level in solution of approximately 1000ppm, above which the silver recovery fell markedly. Cyanide and lime consumptions for this ore were high (typically 5 kg/t and 40 kg/t respectively), hence the processing of this particular ore by cyanide leaching is un- economic at current silver prices.

Jan 1, 1987

By G C. Kiel, G J. Nicholson

Corporate governance has never been more topical. A glance at any major newspaper or business publication will reveal a litany of corporate failures based upon the governance of the organisations involved (eg Byrne, 2002; Hayes, 2002; The Economist, 2002). The increased compliance requirements and speculative nature of our industry means that corporate governance systems are, if anything, more important than in the general business community (Arthur, 2001). Rather than focus exclusively on the contribution of governance to corporate failure within the mining industry, however, our objective in this paper is to examine how boards can add value to the corporations that they govern. In order to highlight how a board can add value to a company, we commence by outlining the role of the board in the modern corporation in general and the mining industry in particular. We then introduce the concept of shareholder value and identify the steps on which a board needs to focus to enhance shareholder value through value tracking processes. Our discussion pays particular attention to the importance of organisational culture to the companyÆs activities and utilises three case studies from the mining industry. We conclude with an overview of what mining boards can do to enhance their culture and drive performance changes for the benefit of the companies they govern.

Jan 1, 2002

The writers of these notes, having conducted some tests on the steam consumption of air compressors under varying conditions, believe that the detailed results of such tests will be of interest to the members of the Institute, and may lead to the contribution of further and more valuable information, of benefit both to manufacturers and users of this class of machinery-to the manufacturer in that he frequently has the opportunity of giving a very thorough test to the machine in the shop, and-tothe user or purchaser by making clear to him what may be reasonably demanded of a high-class machine. It must be remembered that, though of the highest importance, a low steam consumption is but one of the many features of a high-classmachine; for the present, however, it has been considered advisable to confine the paper chiefly to the first-mentioned aspect, with such information concerning the air ends as is obtained along with the steam consumption tests. Unfortunately, too few of these tests are conducted, and but few results are published, therefore the writers feel that no apology is needed in bringing their results before the members.Some nine months ago the Brilliant Extended G. M. Co. was supplied with a compressor by Messrs. Thompson and Co., of Castlemaine, and with the object of testing its actual performance.

Jan 1, 1907

Water is a key resource input to copper heap leach operations in both quality and quantity. A number of recent developments in analysis of the technology have shown that water consumption can be optimised. The leach consumption has been generally considered in terms of minimisation of the evaporative loss by changing the application method (drippers or wobblers). Modelling of the irrigation effects on leach rate has shown that the poorer surface coverage from drippers has an adverse effect on the leach extraction rate. This is particularly evident in the early part of the leach. The use of different irrigation systems during alternate parts of the leach cycle can have benefits in minimising the water consumption without an unacceptable outcome from extended extraction times. By combining the leach rate effect with the evaporative loss estimates, an economic decision matrix can be generated to allow the operator to select an appropriate leach irrigation strategy, combining both irrigation delivery and irrigation rate. In the SX-EW plant, the total quantity of EW bleed and SX scrub stage bleed (both for iron control) can be reduced to an absolute minimum. The economic minimum may be different depending on the cost of producing the high-quality water used to replace the bleed streams. Adjustment of the SX process, in particular use of multiple entrainment control steps, can provide significant reductions in the total bleed and make up requirements.

Jan 1, 2003

By Jin C, Shi X

The electrochemistry of leaching gold with thiosulphate has been studied systematically by using electrochemical techniques. Results show that the current peak of anodic dissolution of gold occurs at about 50 mV(SCE) and there is passivation in the polarisation curve in the thiosulphate solution in the absence of ammonia. Ammonia markedly improves the anodic dissolution rate of gold and reduces the passivation as well as making the current peak shift negatively. Results also show that there is no current peak for a cathodic process in the range of 0 -900 mV(SCE) in the thiosulphate solution in the presence of oxygen but absence of cupric ions and ammonia. In the solution containing 0. 1 mol/L cupric-ammonia ions, the peak occurs at about -400 mV (SCE) and the cathodic process is characteristic of a catalytic reaction. Oxygen presents a predominate effect on the cathodic process. Based on the electrochemical investigation, the following mechanism of leaching gold with ammoniacal thiosulphate has been proposed. Ammonia reacts primarily with gold ions on th anodic surface of gold and the formed A (NH3)2+ rea~s then with S2O 3 in solution to form the stabler Au(S203) 2 . Cu (NHS) 4 gains electrons on the cathodic surface and is reduced to CU(N) ? which is then oxidised by oxygen and regenerated into Cu(NH3) 4 after entering the solution.

Jan 1, 1993

Mining projects draw together stakeholders with various degrees of experience in managing and assessing financial risk. When this risk is not fully appreciated or quantified, the potential for making decisions not suited to investor requirements is significantly increased. A feasibility study provides key information on project development potential, requiring detailed technical investigations with thorough financial analysis. Centaur Mining and Exploration (CME) owned and operated Cawse Nickel Operations (CNO), one of three Australian projects to develop and process vast amounts of near surface nickel resources. A technical ædue-diligenceÆ and æbankable feasibility studyÆ confirmed the large resource base, newly applied yet tested technology and relatively low unit costs would produce nickel in the lower half of industry operating costs. A number of production variables including capital requirements, delayed start-up, nickel grade, processing, maintenance and product output were outside the feasibility estimate. This was combined with exchange rate fluctuations and lower Ni prices. The inability to generate adequate cash flow and service debt repayments ultimately led to receivership and liquidation of all assets. Following the sale of CentaurÆs gold and nickel divisions, $A 784 million remained outstanding to creditors. This paper aims to define key issues leading to CNOÆs collapse by reviewing feasibility parameters, valuation methodology and project development. Some methods of assessing project viability are discussed with the aim of increasing stakeholder risk awareness.

Jan 1, 2003

By J J. Cilliers, E Ventura-Medina

Mineral froth flotation is used to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. As air is blown into the slurry, the hydrophobic particles attach to the air bubbles, while the waste particles remain in suspension. While the froth rises up, bubbles start to coalesce and burst, allowing the entrained liquid surrounding the bubbles to drain and return part of the gangue to the pulp. Mineral separation is therefore a function of the amount of valuable material loaded on the bubble shells, as well as the amount of gangue material entrained in the liquid channels separating the bubbles (Plateau borders). As a result, the separation performance of the process is affected by mineral attachment and drainage or bursting in the froth. This study aims to establish the relationship between solids loading, froth stability and separation performance. For this purpose, a series of industrial experiments were carried out to measure mineral attachment as well as bubble bursting by combining direct sampling of the bubble films and video image analysis of the froth surface. This work suggests that the solids loading on bubbles strongly affects the separation performance. The results generally showed that solids loading and concentrate grade are closely related, while froth bursting rate can be linked to the drainage of gangue from the Plateau borders and also to the overall recovery of valuable mineral. It was shown in particular that higher loadings, usually associated with higher froth bursting rates, are indicative of more selectivity in attachment and therefore a higher mineral grade in the concentrate. Additionally, this work suggests that bubble solids loading and froth stability are essential parameters to include in froth flotation models as they allow control and optimisation of the flotation performance.

Jan 1, 2005

By Ho-Tun E, Stewart PSB

The definition and recognition of silver minerals is very difficult. In general such minerals occur at low concentration and can be hard to identify and measure using conventional optical mineralogy. The present paper describes the use of the QEM*SEM system to tackle this problem and provide information of use to the metallurgist. Three aspects of QEM*SEM are used to special advantage in this application. Firstly the automated mode of operation is used to make a rapid search for the sparse phases. Secondly the X-ray capability is used to identify the mineral phases. Finally the image analysis programs quantify the distributions of the minerals which are found. The paper deals with the identification stage of the process and with the use of the data which can be derived. Silver minerals which covered a range of ore types and composition were collected and studied in detail. On the basis of these measurements and information received from a number of mining companies regarding the important minerals, a classification table was prepared. This table listed about 40 different silver mineral types which could be identified by QEM*SEM and which were of interest in silver recovery processes. Where the silver occurs in solid solution in concentrations greater than about one per cent, the silver content in the species was subdivided into ranges based on statistical intervals. The QEM*SEM system was programmed to recognise these as separate species. Examples are presented of the use of the system in defining the type and morphology of the silver mineralisation to assist in the assessment of batch flotation test Samples.

Jan 1, 1993

By H Aral, L Malishev

The carbothermic chlorination of titaniferous materials such as rutile, synthetic rutile (SR), upgraded slag and ilmenite in a fluidised bed is an established commercial process. In this work, ilmenite sourced from the Murray Basin area of South Eastern Australia was chlorinated and an assessment of the chlorination characteristics of the ilmenite, in terms of pre-treatment, type of reductant and reaction time was made. Selective chlorination of Murray Basin ilmenite to remove Fe and Mn was achieved in this work. A synthetic rutile sample containing around 93 per cent TiO2, one per cent Fe2O3 and 0.5 per cent MgO was produced at a chlorination temperature of 1000¦C with around 25 per cent loss of Ti as TiCl4. Raising the reductant to ilmenite ratio in the chlorination reactions increased the amount of Ti chlorinated. However, complete chlorination of Murray Basin ilmenite to produce FeCl3 and TiCl4, was not achieved under the conditions used in this work. Pre-oxidation of Murray Basin ilmenite before chlorination had little affect on its reactivity, compared with æas receivedÆ ilmenite. In contrast weathered West Coast ilmenite chlorinated appreciably better than West Coast primary ilmenite, in terms of bed residues remaining and amounts of elements removed. The presence of large amounts of Mg and chrome spinel grains in the Murray Basin ilmenite used in this study are likely to make it difficult to chlorinate directly in a commercial chlorinator. However, this is not to say these ilmenites will be unsuitable for chlorination applications. Further work is needed in the separation of Mg and chrome spinel grains from Murray Basin ilmenites and the products resulting from these tests could then be assessed in terms of chlorination performance, so that further processing options can be explored.

Jan 1, 2000

By S R. Grano, M Vera

This paper deals with two separate case studies investigating the froth phase performance and characterisation of two industrial rougher/ scavenger flotation circuits. Froth phase performance was quantified using a mass balance approach to estimate froth zone recovery. Measured characteristics of the froth phase included frother solution concentration determined by gas chromatography, and the time taken for an equilibrium froth sample to decay to one-half of its original froth height. The latter measurement is referred to as the æfroth half-lifeÆ and is strongly linked to froth stability. Special methods and techniques developed to preserve frother in solution and to measure froth half-life are briefly described. The frother type in the first case study was a mixture of straight and branched alcohols, whilst the frother type in the second case study was a mixture of alcohols, aldehydes and triethoxybutane. The first case study focussed on a flotation circuit treating a low-grade ore containing only a small fraction of floatable copper sulfide minerals, while the second case study focussed on a flotation circuit treating a higher grade complex sulfide ore containing significant quantities of chalcopyrite, galena, sphalerite and pyrite. It was found that froth zone recovery of valuable mineral generally decreased down-the-bank of the two industrial rougher/scavenger circuits. Moreover, decreases in froth zone recovery significantly limit the overall cell recovery of valuable mineral achievable from the plant scavenger cells. However, the decrease in froth zone recovery could not be linked to the removal of frother from the pulp solution to the concentrate product in the preceding rougher flotation stages. Measurements of residual frother in solution suggested that, approximately, only five to ten per cent of the added frother was removed into the rougher/scavenger concentrate, with the remainder appearing in the scavenger tailings. This finding suggested there was apparently adequate frother in solution in the scavenger stages.

Jan 1, 2005

High-sulphidation (HS) gold, silver and/or copper deposits are generated in both the epithermal and the upper parts of the underlying porphyry environments over vertical intervals of up to 2 km. The HS deposits are generated in advanced argillic lithocaps, which are products of the absorption of acidic magmatic volatiles by voluminous groundwater systems. Mineralisation styles in HS systems reflect depth of formation as well as the interplay between structural, lithological and hydrothermal parameters. The deep parts of HS systems, at depths of >1000 m, are typified by disseminated copper¦gold mineralisation comprising digenite, chalcocite and covellite in pervasive advanced argillic as well as underlying sericitic alteration. In highly telescoped systems, suchmineralisation may overprint porphyry stocks and associatedquartz-veinlet stockworks. Intermediate levels of HS systems commonlycontain fault-controlled copper-gold mineralisation, typically as enargite in bodies of vuggy residual quartz, silicification and/or massive pyritic sulphide. The shallow parts of HS systems, at depths of The exploration focus is on four principal HS mineralisation styles: 1. copper (eg Chuquicamata, Monywa) or copper-gold (Wafi) in thedeep porphyry-hosted parts of systems preferably, in the case of thelatter, where supergene oxidation is limited and, hence, flotationmay be used for metal recovery,2. copper¦gold-bearing replacement mantos and pipes hosted bycarbonate wallrocks in the deep parts of systems (eg Bisbee),3. high-grade gold in late-stage veins or hydrothermal breccias thatoverprint the intermediate to shallow levels of systems (eg El Indio,Goldfield), and4. large, bulk-mineable gold deposits in the shallow parts of systemsthat were subjected to supergene oxidation, thereby permittingheap-leach treatment (eg Yanacocha, Pierina).To these preferred HS styles may be added the low-sulphidation veinor disseminated gold¦silver mineralisation that is commonplacealongside many HS systems (eg Victoria at Lepanto). * Originally published in the Proceedings of PACRIM æ99,published by The AusIMM.

Jan 1, 2000

It is usually the case that the short-term plannerÆs role is occupied by the younger site mining engineer. ThatÆs because mine scheduling is generally seen as a mundane and thankless task. But, short-term planners play an extremely important role in maximising the value of the mining resource, generally the companyÆs biggest asset. A look at any mining operation today will expose the competing drivers behind the operational and strategic plans. Operations are too often faced with pushing short-term constraints. It is the responsibility of the short-term engineer to answer the question of æWhere to next?Æ. In answering this question the young mining engineer is in an environment overflowing with urgency and constraints. Hasty decisions made at this time may have significant adverse consequences to the long-term value of the resource. Long-term strategy must address a broad and expanding number of issues that are generally overlooked by the short-term planner. It takes a holistic, rather than the prescriptive approach of short-term planning to determine the best strategic direction for the operation. To better understand the consequences of decisions made at the operational level short-term planners need better vision of the whole business. The key to improving the mining business is a planning process that integrates the short-term planners role with the overall mining strategy. Future developments in the mine planning process will focus on bridging this ædisconnectÆ between the operational objectives and the long-term goals. Improvements will come from the tools which planning engineerÆs use, and the planning methodology surrounding them. There will be significant hardware improvements to improve the speed with which a short-term planner can evaluate plausible options. Software that maximises the use of the improved hardware will be developed. Complimenting these technological improvements, conceptual methodologies of mine planning will improve to allow strategic planning to be brought within the focus of the short-term planning engineer. In todayÆs mining industry the young mining engineer is embarking on a career where business processes are paramount. This paper discusses the ædisconnectÆ that occurs today between the operational planning and long-term strategy and how this is driving developments in mine planning today.

Jan 1, 2003

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

The disadvantages of the present zinc producing methods, RLE and ISP, are high energy consumption and environmental problems. Therefore, efforts have been directed in Outokumpu Zinc towards the development of alternate routes. One interesting pyrometallurgical process to produce zinc is to inject zinc calcine together with a solid reductant into molten iron, saturated with carbon. This process has been studied by thermodynamic calculations, laboratory tests and mini-pilot test runs at Outokumpu Research Oy, Pori, Finland. The results of these tests are presented and discussed in this paper. The mini-pilot tests demonstrated that over 97 per cent evaporation of the zinc was possible using a reactive coal dust as the reducing agent. The recovery of zinc in the metal phase was at best 88 per cent of input zinc, but only part reported in molten lead in the splash condenser. The final metallic zinc contained at best 98 per cent Zn, the main impurities being dissolved lead and coal carried along with the flue dusts.

Jan 1, 1993

The author describes 1. The classification and characteristics of various thick seam mining techniques in various Japanese coal mines. 2. Practices of thick seam mining methods experienced in Taiheiyo Coal Mine. Currently, thick single lift, simultaneous multi lift and non simul- taneous multi lift mining methods are adopted as underground flat thick seam excavations in Japan. These are now reliable and effective in increasing the extraction ratio. At Kushiro Colliery of Taiheiyo Coal Mining Co., these three thick seam mining methods have been used. According to the results, if solidification of the top lift goaf is essential, the non simul- taneous multi lift mining method is the most effective in increasing the extraction ratio without minimising productivity of each lift and it points out that further development of this method is necessary.

Jan 1, 1976

By Moffatt G

Approval to operate Longwall No. 7 at Appin Colliery in 1979 was granted pursuant not only to the usual statutory provisions, but also that an adequate means of drainage of methane gas be incorporated. A methane drainage plant was subsequently designed and constructed some two km from the pit top at the site of the Colliery main upcast and down cast shafts. Modern plants of this nature are completely automated using programmable controllers and computers to provide control and management reporting functions. Complex mechanical systems are installed to extract the gas and in handling and storage processes. Gas utilisation plants exist which can generate power from methane. These plants are further enhanced by harnessing waste heat produced in the generation process. The installation, automation control and monitoring of these plants incorporates many facets of engineering from high voltage power supply and computer technology to complex gas handling procedures used in gas compression storage.and generation of electric power.

Jan 1, 1982

The Hodgkinson goldfield contains over 50 separate lodes which have produced 9.7 tonnes of gold from ore averaging 37 g/t. The gold-quartz.lodes are spatially separate from tin and base metal mineralisation, associated with Permo-Carboniferous granitoids in the province. Host rocks consist of sub-greenschist metamorphic grade shale, conglomerate, sandstone, spilite, chert and melange. Oreshoots average 100 x 30 x I m in Size and are contained in cross-cutting quartz. filled with steep-dipping shear zones. Mineralisation in the quartz. consists of gold with minor arsenopyrite, pyrite, galena, and sphalerite with rare calcite. Scheelite and stibnite are aSSOCIated locally but are not necessary proximal or coeval. Alteration is restricted to centimetre-scale phyllic selvedges adjacent to the veins and veinlets.Most of the lodes and vems occur within six main 1.5 x 0.25 km mineralised areas whIch may indIcate separate areas of fluid flow and precipitation. Ore controls differ m melange- and sandstone-hosted lodes but several features are common to all the oreshOOlS. Most of the lodes occur within zones of duauon that are caused by splaymg, refraction through carbonaceous shale-sandstone contacts, or by rolls and changes in strike and dip.Lithologic contacts may act as areas of permeability and chemistry contrast which focus fluid and precipitation. Tensional veins are common between parallel shear zones and curved spur veins occur both in the hangingwall and footwall of the main fissure. Intersections and contacts may have enhanced local fluid flow in many of the areas.

Jan 1, 1991