Search Documents

By T Hodgkin

The WA Goldfields is a highly productive gold and nickel mining area, but is arid with highly saline groundwater. Groundwater is widely used to supply process water to mines in the region but high groundwater salinity, commonly exceeding 50 000 mg/L TDS, tends to increase processing costs, limit end uses for the water, cause problems with disposal and potentially increase impacts on a sensitive arid environment. The area has low rainfall (200 - 270 mm/year) but run-off, particularly during cyclonic events, is high. Our experience suggests that stream flow from catchments in the area can produce a divertible yield of 8 - 17 ML/km2/year. An evaluation of stream flow harvesting using AnglogoldÆs Jubilee Pit predicted that 1000 ML/year of good quality water could reliably be supplied to the Sunrise Dam Gold Mine. Because of high rainfall variability, it is likely that an alternate source of water supply will be necessary when operating a surface-water harvesting scheme in the WA Goldfields. However, a combination surface/groundwater supply could have substantial cost, operational and environmental benefits compared to traditional supply systems that utilise groundwater only.

Jan 1, 2003

By Conley R, Payne I

The Vickery Coal Mine commenced open cut mining operations in May 1991. All overburden and interburden is drilled and blasted for excavation by dragline or hydraulic excavator. The mode of operation adopted from the feasibility studies requires that throw blasting of the overburden be used to assist dragline productivity.This paper reviews the development of the drilling and blasting practices with particular emphasis on the throw blasting of the overburden and optimisation of costs. This review includes analysis of the pre-production drilling and blasting feasibility studies by comparison with actual results.

Jan 1, 1992

After a very brief historical survey and overall assessment of traffic requirements, the invitation by the British and French Governments for private groups to make proposals for a "fixed link" is described, and the resulting plethora of proposals is reviewed. The three schemes which gave some promise of being adequately backed by private finance are described as follows:

Jan 1, 1987

By R Balusu, P Humphries

In combination with detailed field studies and goaf gas characterisation, computational fluid dynamics (CFD) models have been used to develop optimum and effective strategies for inertisation during longwall sealing operations to achieve goaf inertisation within a few hours of panel seal-off operation. This study has combined detailed analysis of the performance of various inertisation field trials together with CFD modelling results of different inertisation operations in order to develop the optimum inertisation strategies. A number of parametric studies were conducted on the base case CFD models that had been calibrated and validated based on the information obtained from previous inertisation studies and goaf gas monitoring. These studies included changes in inert gas injection locations, inert gas flow rates, seam gradients, and different inertisation strategies to investigate their effect on goaf inertisation. Studies indicate that the strategy of inert gas injection through the MG seal was not as effective as the alternative strategy of inert gas injection at 200 m behind the face. Innovative inertisation strategies have been developed and subsequently implemented at an underground coal mine in Australia. Further investigations have been carried out in the development and demonstration of proactive inertisation strategies with the objective to suppress the occurrence of spontaneous heatings in active longwall faces, in particular under unexpected scenarios such as during slow retreat/face stoppage due to difficult geological conditions. Initial trials at two Australian longwall panels have demonstrated the great potential of this practice to contain the onset of heatings in the goaf.

Jan 1, 2005

By Lovett EP, Johnson CR, Dunlop GA

Seven streams of a low tonnage pilot plant operation on Cu/Pb/Zn ore from the Golden Grove Project were continuously assayed using an AMDEL In-Stream Analysis (ISA) system. The ISA instrumentation is briefly described as is the calibration procedure employed. The successful application of this instrumentation in the dynamic environment of a pilot plant operation is discussed. The operational sequence of the Golden Grove pilot plant is outlined along with the original project objectives and how they were achieved by the implementation of ISA. Results for the different complex flowsheets used are discussed, followed by the perceived benefits of installing such equipment in this operation.

Jan 1, 1986

By J Khosa, J Manuel

Iron ore sintering is very complex with many interdependent variables. For the same ores, the sinter quality and sintering performance may vary significantly with the scale at which the sintering tests are conducted. Therefore it is important to understand the effect of test scale on sintering performance and sinter quality while interpreting the test results. In this paper, different scales of iron ore sintering research at CSIRO are described and compared. This is followed by the results of two sinter blends tested at different scales. The results are compared and correlated to demonstrate the benefits of iron ore sintering research at the laboratory (4 g), small (5 - 8 kg) and pilot (55 - 140 kg) scales.

Jan 1, 2007

Results are presented of the investigation of gas dynamics of the blast furnace process obtained on laboratory models and operating furnaces. Gas residence times were measured using a helium tracer technique developed for the purpose. Residence times were determined in furnaces of 1007 m3 and 1719 m3 and results used in the calculation of the burden parameters and to estimate the distribution of the gas flow along the furnace radius. The effect of tuyere injection of coal dust on gas distribution was also investigated and the advantage of continuous injection compared with intermittent injection is noted. The unevenness of gas distribution across the furnace area is found to correlate well with differences in the size analysis of the iron-bearing component of the burden. The mixing of the gas streams between the neighbouring raceways was studied. It is shown that in the central region of the furnace gases from every tuyere are mixed together, whilst in the peripheral regions mixing is more localised and includes only the sections consisting of five adjacent tuyeres. A solution is proposed to the problem of a theoretical evaluation of the critical gas velocity. A simple relationship between the Reynolds and the Archimedes numbers was obtained from which, after substitution of the burden size data and the gas parameters, it is -possible to evaluate the critical gas velocity. Conclusions include information relating to the optimisation of the gas distribution and views on reducing gas injection at elevated furnace levels.

Jan 1, 1975

By Carlie JC

Many low sulphidation epizonal gold and zinc-lead vein deposits within magmatic arcs are situated on basement highs, and post-date both the main volcanic episode and porphyry copper (gold) mineralization. These features are best explained by emplacement of a flat batholith a few kilometres beneath each mineral district, as recently demonstrated by geophysical data in the Baia Mare district of Romania. The batholith provides heat for the hydrothermal system, and results in extensional faulting both through up-doming of the overlying rocks, and in some arcs through incipient collapse of the thermally weakened crust under regional extensional stress. More water-rich magmas emplaced at greater depths could explain some deep epizonal and mesothermal gold deposits situated outside magmatic arcs.

Jan 1, 1995

By M Roper, M Lovitt

WMC Resources Olympic Dam Operation located in South Australia, is a poly metallic underground sublevel open stoping (SLOS) mining operation with a current annual production rate in excess of 9.0 Mt. Stope size, geometries, geotechnical considerations, drilling and blasting are critical components in stope performance. These factors are further influenced by stringent ventilation requirements due to the presence of airborne radioactive contaminants from uranium mineralisation. Stope planning is complex and mass blasting methodologies have been trialled at Olympic Dam with the view to reducing the frequency of stope blasts, improving stope stability, productivity and ultimately improving overall stope performance. A key aspect in the ability to undertake underground mass blasts of this scale is the application of i-konTM electronic initiation technology by Orica. In the past two years in excess of three million tonnes has been initiated utilising this electronic technology, with an average blast of 250 000 t ranging to the largest to date being 580 000 t. By providing flexibility in blast designs, the use of electronic detonators has allowed mass firings over multiple sublevels. This has resulted in a significant reduction in stope extraction steps compared to conventional pyrotechnic firings. The benefits of this reduction in the number of stope blasts are wide ranging from improved stability of interim stope voids between blasts, reduced blasthole damage, improved blast vibration management and reduction of complex changes to ventilation systems for blasting.

Jan 1, 2004

By I P. W Chau

Construction of twin stacked railway tunnels through mixed ground conditions in the heavily populated urban environment of Hong Kong, including tunnelling in poor ground conditions, with low cover and under or adjacent to sensitive structures with minimal impact was the challenge presented by the tunnelling section of the Kowloon Southern Link project. This paper details how twin 1.1 km tunnels of 7.0 m internal diameter were driven by Mixshield tunnel boring machine (TBM) in mixed ground through one of the exclusive shopping and hotel districts in Kowloon. The paper addresses the challenges required to be considered and managed for the success of the project, including ground conditions, TBM selection, Mixshield TBM operation, settlement monitoring and control, ground- borne noise and vibration, proximity to utilities, buildings, roads and operating railways.

Jan 1, 2008

Naturally occurring organic plastics have been in use for over 2,000 years. Plastics based on chemically modified organic polymers date back only about 100 years, and those based on synthetic polymers about 50 years. The development of ,these two latter groups up to the present day is outlined, and the basic techniques currently available for polymer-building and modi-fication (blending, copolymerisation, quantitative and qualitative struc-tural control, and'si de-group reactions)-are reviewed.

Jan 1, 1962

By G R. Hancock, D Verdon-Kidd, M J. Saynor, J B. C Lowry, T J. Coulthard

The ability to simulate the stability of post-mining landscapes over time scales ranging from decades to millennia is a critical element in the assessment of closure designs for uranium mines. Landscape Evolution Modelling (LEM) technologies provide a means to simulate and assess the long-term geomorphic stability of a conceptual rehabilitated landform for periods of thousands of years. However, a major issue with simulations derived from long-term modelling are the limitations associated with the data inputs. Specifically, simulations which utilise historic rainfall data only represent the variability of rainfall events that have occurred over a relatively short period. Consequently, these simulations run the risk of not accounting for the full range of rainfall variability that might be expected over an extended period of up to 10 000 years. Therefore, for this study a probabilistic approach was adopted to generate a stochastic synthetic rainfall data set to produce a series of unique rainfall scenarios, each representing a simulated period of 100 years. Importantly, utilising such an approach allows uncertainty in predictions to be better accounted for and provides a range or probability of likely outcomes.In this study, the effect of ten individual rainfall scenarios are assessed in terms of their impact on the predicted erosion and denudations rates produced by the CAESAR-Lisflood LEM for a conceptual rehabilitated landform of the Ranger Uranium Mine (RUM) in the Northern Territory of Australia, focusing on the Corridor Creek catchment (Figure 1). While legislation requires this site to be erosionally stable for at least 10 000 years (Commonwealth of Australia, 1987), here the focus is on the first one hundred years of landscape evolution, as this is the period in which erosion is expected to be higher, with limited vegetation cover or pedogenic development in the initial decades after rehabilitation. It is also the period where the drainage pattern is set.CITATION:Lowry, J B C, Verdon-Kidd, D, Hancock, G R, Saynor, M J and Coulthard, T J, 2016. Application of synthetic rainfall data to long-term modelling of a rehabilitated landform, in Proceedings Life-of-Mine 2016 Conference , pp 75–79 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923

During conventional eddy current separation, a repulsive force is applied to metallic particles by placing them in a rapidly changing magnetic field generated by a spinning magnetic rotor carrying an arrangement of alternate magnetic poles. This method works effectively for larger non-ferrous metallic objects, such as aluminium cans, but as the metallic particles become smaller, the bulk repulsive force on the particles is increasingly replaced by a rotational torque. Therefore, for small metallic particles it makes sense to use particle rotation, rather than particle repulsion, to effect a separation. Eddy current separators using particle rotation are similar in construction to present separators, but are designed to produce a rotating field of essentially constant angular velocity and field strength. Practical and economic particle rotation eddy current separations are possible down to particle sizes of about 200 ¦m, but separations, at probably uneconomic rates, can be carried out on particles as small as 50 ¦m.

Jan 1, 2000

By Hayes P. C

The kinetics of reduction of PbO-silicate melts in CO-N gas mixtures at 900¦C have been studied. Rea~tion rates were measured by moni- toring the CO2 content of the product gas. A wide range of gas and melt compositions and gas flowrates have been investigated. The overall reaction rates in heterogen- eous systems are typically characterised by a steady increase as the gas flowrate is in- creased. At low flowrates the processes are limited by gas film mass transfer. At high flowrates it is expected that the rates will tend to maximum values determined by either the rate limiting chemical reaction or diffusion in the condensed phase. In the present series of experiments it has been found that for any given gas composition the overall reduction rate goes through a maximum with increasing gas flow. The maxima, which occur at relatively low gas flows, are more than an order of magni- tude greater than those observed at high gas flowrates. The results of these and other experiments are presented and analysed. Possible rate limiting mechanisms in the reaction system and their implications regarding commercial reactors are discussed.

Jan 1, 1987

By A G. Pavlides, B L. Weekes

The Sepon Copper Project is located in the Savannakhet Province of Laos PDR and is operated by Lane Xang Minerals Ltd (LXML). An Ausenco - Bateman Engineering joint venture, the Khanong Development Group (KDG) managed engineering, procurement and construction of the project. The plant was fully commissioned in March 2005, two weeks ahead of schedule. The plant is designed to produce 60 000 tpa of cathode copper. The process flow sheet includes a pressure oxidation (POX) circuit that leaches pyrite flotation concentrate to generate ferric ions and sulfuric acid for use in atmospheric leaching of a predominantly chalcocite ore. The process is unique in that the chemistry in the autoclave is forced to produce a basic ferric sulfate precipitate for downstream recovery of ferric iron. This paper describes the design, construction and commissioning of the pressure oxidation circuit. The challenges imposed on construction and commissioning due to the remote location of the site, landlocked status and underdeveloped infrastructure in Laos are highlighted.

Jan 1, 2005

By R H. Eric

Surface wave formation induced by a high-strength submerged jet in a bottom blown metallurgical vessels has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations. Experimental results have been discussed in terms of the wave period, wave frequency and wave amplitude with respect to air injection rate and tuyere configuration at a 0.23 m bath height. The results from high speed photography observations displayed the formation of rotating surface waves which circulates within the water model. It was found that the frequency and the amplitude increased with gas injection rate. The wave period for off-centre nozzle orientation was found to be lower than those of the centre configuration. The experimental results also showed that the frequency of a rotating wave increases when the tuyere orientation becomes off-centred . The predicted amplitudes were in very good agreement with the experimental values over a range of gas flowrates between 0.00599m 3/s to 0.01081 m 3/s.

Jan 1, 2000

By Rashchenko AF, Voiloshnikov GI, Elshin VV, Khomutov VV

The sorption method for the precious metals recovery fromsolutions and pulps are a perspective trend of modernhydrometallurgy. Russian gold mining industry uses thesemethods, anion-exchange resins being applied as sorbents. Theanion exchange resins allow effective recovery of preciousmetals, however, they have several drawbacks as compared withactivated carbons: high cost of sorbents; difficulties arisingduring treatment of pulps with complex ion composition;necessity of using titanic equipment and thiourea for gold elutionfrom loaded anion-exchange resin and its regeneration.

Jan 1, 1993

By F A. Roddick, C Swaminathan

As remaining gold deposits tend to become more refractory, some form of oxidative pre-treatment involving hydro or pyrometallurgy is necessary to maintain high metal recoveries. These pre-treatments include pressure oxidation, bio-leaching or roasting. In the past, the primary criterion for selection of oxidative pre-treatment relied mainly on the extent of gold recovery and relative economics. In this study, a different approach has been adopted, ie the quantitative determination of environmental performance of the oxidative pre-treatment processes bio-leaching, roasting and pressure oxidation to assess which had the least impact on the environment. By establishing the environmental performance of processes, waste minimisation can be addressed early in process selection. Using mass balances, the environmental theme method was applied to determine the performance, on the basis of gold treated, of the oxidative pre-treatment processes of selected plants. No clear trend was observed in the overall impacts of each of seven plants, with all but one of the environmental evaluation indices being of the same order of magnitude; this was probably due to masking effects arising from the large variations in feed composition, tonnage, and gold levels. Within each type of pre-oxidation plant however, certain trends were detectable. For instance, irrespective of plant size, ore composition or mineralogy, for the bio-leaching and pressure oxidation units, the general order of environmental impact from greatest to least was sequentially toxicity, acidification potential, depletion of resources, solid waste generation and greenhouse enhancement. For the roasters the acidification potential was the most significant. Determination of the environmental performance of the oxidative pre-treatment of a hypothetical ore in a plant of fixed tonnage was undertaken to remove the possible masking effects of variables associated with feeds of different mineralogy, gold tenor and tonnage. The bio-leaching process gave a marginally better performance than pressure oxidation, the roasting process the worst, although there was not a great difference between them. The decreasing order of contribution to the environmental index was acidification potential, toxicity, resource depletion, solid waste generation and greenhouse enhancement for bio-leaching and pressure oxidation; whereas it was acidification potential, solid waste generation, toxicity, resource depletion and greenhouse enhancement for roasting. Since the major contributor to the environmental index was the acidification potential, the environmental performance of treatment processes for the acidic effluents was calculated. After neutralisation of the net acid resulting from bio-oxidation and pressure oxidation, and the application of various scrubbing and product formation processes for the sulphur dioxide from the roasting process, it was shown that pressure oxidation gave a marginally better performance than bio-leaching, ahead of roasting. This study demonstrated the potential for the development of a predictive tool which could be used in determining the environmental performance, and thus the selection, optimisation, and improvement of pre-oxidation processes for least impact on the environment. These would allow operation of these processes within defined environmental performance limits and decisions regarding the desirability of processing various parts of a heterogeneous orebody to be made on environmental grounds.

Jan 1, 2000

By R Dimitrakopoulos

Optimisation and mathematical formulations for open pit design and long-term production scheduling have been available since the 1960s. There are two main concerns in the application of existing mixed integer programming (MIP) models in open pit mines: a. the feasibility of generating both optimal solutions and practically mineable scheduling patterns and b. the inability to deal with in situ variability in orebodies and account for uncertainty. In dealing with these issues, a general open pit production scheduling method for multi-element deposits is presented and subsequently used to optimise the long-term production schedule in a nickel laterite deposit. The application shows the weaknesses of MIP formulations in terms of generating optimal solutions as well as practically feasible mining patterns. The application of the same formulation in the presence of in situ orebody variability and uncertainty uncovers a major reason for deviations of scheduled production from actual production, and outlines additional limits of traditional optimisation formulations as well as future needs.

Jan 1, 2003