Search Documents

By G Senanayake, J Andreazza

The general experience in gold cyanidation research activities and plant practice is that high oxygen and cyanide concentrations improve gold leaching kinetics which in turn reduce residence time and increase throughput. This paper shows how the improved pre-oxidation method for the pyrrhotite rich gold ore of Bounty Gold Mine has increased gold recoveries at lower reagent consumption rates. The installation of a pipe reactor, in conjunction with a Multi Mix Systems oxygen injector, has lowered the amount of oxygen required to achieve a dissolved oxygen level target of 20 mg/L. The improvement of the pre-oxidation stage and lead nitrate solution addition has led to a reduction in the free cyanide concentration required for leaching, resulting in a decrease in cyanide consumption rate by 36 per cent to achieve a one to two per cent improvement in the gold recovery.

Jan 1, 2002

By A Thornton, D Engelhardt, J Woodg

Grinding is a critical part of nearly all mineral processing operations. It is the largest consumer of energy on the mine site (and thus indirectly a producer of greenhouse gas through the generation of electrical energy at the power station). Since comminution is one of the main consumers of electrical energy worldwide, efficient control of grinding mills is of paramount importance. Mill Auto-Pilot is a control system developed for SAG mills to stabilise load and power and improve the efficiency of control and increase throughput. A dynamic, mechanistic model of the grinding circuit is used to determine circuit parameters which can not normally be measured using conventional instrumentation. The circuit model is built from models of the unit operations (such as conveyors, SAG mills, cyclones, sumps, etc), and so captures the dynamic complexities and interactions of real circuit operation. CSA Mines at Cobar NSW accepted an offer to be the reference site for Mill Auto-Pilot and the system was installed in March 2004. In this application the model is used to predict mill load mass, mill solids residence time and cyclone underflow density. These parameters are used to control mill load, power and mill discharge density. The outcomes of the introduction of Mill Auto-Pilot at the CSA Mine are discussed.

Jan 1, 2004

The St George orebodies are situated within the tectonically disrupted eastern limb of the Boogardie Syncline.Highly disturbed rafts of banded chert formations occur within a sequence of felsic volcanic tuffs. The chert forms the hostrock for the gold mineralization.The gold distribution within the irregular and narrow banded chert formations is erratic and patchy. The average gold content of the two orebodies is between 3 - 4 g/t Au.Economic mining of these relative small, irregular and low grade St. George orebodies can be carried out by using a highly selective mining method.The highly selective mining method uses an excavator as the principle mining tool. Blasting, breaking and loading of the rocks is done in a different way than by using a front-end loader as with the conventional mining method. Simple, and therefore cheaper, blasting breaks the rocks and lifts them up without major displacements.

Jan 1, 1984

By Gao K, Wu C, Xia J, Burdett M

X-ray diffraction (XRD) and transmission electron microscopy (TEM) techniques have been adopted in this study, to investigate the structure of carbonaceous materials such as graphite, brown coal char as well as coke, in order to explain their dissolution performance during ironmaking. These materials have been selected for study since they are commonly used recarburizers in the metallurgical industry. It was concluded that the crystal structure in a carbonaceous material can have a significant influence on its dissolution into iron melts. The material with the highest degree of ordering, which is graphite, showed the best dissolution performance. In contrast, the material with the lowest degree of ordering, which is brown coal char, showed the worst dissolution performance.

Jan 1, 1996

This paper summarises some observations regarding the way SAG and AG mills work based on the last ten years of pilot plant operation, grinding circuit design and operational reviews for various projects in Australia and overseas. The main purpose is to promote discussion on key factors influencing breakage in a SAG mill. The focus of the paper is on two questions: How do mill lifters and liners really work and have an effect on grinding? How does the mill charge composition impact on grinding performance? The focus of the paper is on observations of mill behaviour in both pilot plant trials and plant operation, particularly on Cadia ore. DEM, by others, and JKSimMet modelling of SAG mill performance have greatly assisted in forming the ideas expressed in the paper and both are valuable tools in developing our understanding of the comminution process. Put in the æextremeÆ form the major observations and conclusions expressed in this paper are that: the main purpose of mill lifters is to reduce mill liner wear and not to promote rock breakage; the often promoted theory that balls impacting the ætoe of the chargeÆ is a dominant form of breakage is incorrect; and fines production in a SAG mill is primarily a function of the rock load mass, with a secondary dependence on ball load for any given circuit configuration.

Jan 1, 2007

By C Yates, S Jobling, Z Y. Yang

The current trend in the UK towards the adoption of retreat longwall mining methods and the associated rapid development of the access drivages have exacerbated the environmental conditions experienced within these workings. There is a recognised need to improve the efficiency of the design and operation of mine ventilation systems in order to maintain an adequate environment and climate within these workings. Any improvement achieved in the quality, quantity and control of the delivered ventilation will assist in the provision of improved gas and dust dilution and climatic control. The paper presents an analysis of the psychrometric data recorded during the execution of a series of comprehensive climatic surveys conducted within two representative deep underground UK coal workings. The surveys were performed across two high production retreat longwall districts within UK Coal Ltd collieries. The surveys employed intrinsically safe psychrometric transducers and digital data-loggers to collect a continuous record of the mine climate over designated weekday production and weekend non-production periods. The transducers and data-logging units are capable of simultaneously measuring and digitally recording changes in the dry bulb temperature and the relative humidity at regular time intervals for extended periods of time.

Jan 1, 2005

By L O. ÆNeill, J Bebek

When Kalgoorlie Consolidated Gold Mines (KCGM) purchased its fleet of 18 CaterpillarÆs dump trucks in 1999, as part of its change to owner operated mining, five CaterpillarÆs Computer Aided Earthmoving Systems (CAES) were also commissioned on Komatsu PC8000 hydraulic shovels and Caterpillar D10R bulldozers. Since then the CAES system has been installed and operational on Komatsu PC3000 hydraulic shovel, CaterpillarÆs D10R dozers and Cat 994 front-end loader while Cat 854 wheel dozer has been fitted with CAESbasic. This investment in advanced machine guidance and control technology has proven very beneficial over the years for the Super Pit with improved safety and increased operating efficiency and productivity. The paper brings into focus how the CAES system adaptation in unique mining conditions assists in production gain, equipment operatorÆs safety, flexibility and independence, personnel removal from hazardous areas, acquisition of operational information and improvements in mine planning and design, benefiting the entire mining operation.

Jan 1, 2003

The last decade has seen a dramatic change in the. size and complexity of mining and mineral processing projects in Austral- asia. Major projects of today are vastly different from major projects of the 19.50's. This change has in turn resulted in a change in the role-of consultants whose contributions have been increasingly in the provision of specialist services and less in the form of overall project design and construction supervision. It is anticipated that, the specialist function will continue to represent the principle mode for consultant participation in major, projects. However, by means' of international affiliation, the development of comprehensive engineering and project management capabilities and possibly as a result of Government intervention, it is expected ,that local consultants will assume an increasing degree of participation in.the overall project design and supervision Function.

Jan 1, 1975

The introduction ofa submerged entry tundish nozzle incorporating a cylindrical internal space for argon distribution to its inner bore slab is described. In co-operation with the refractory supplier, four major phases of nozzle development have been undertaken. Problems as well as successes are outlined.Significant reduction in alumina clogging ofnozzles has been achieved along with a decrease in nozzle consumption, using resin bonded alumina graphite with up to 4 different materials "zoned" to give resistance to thermal shock, gas leakage, and erosion.

Jan 1, 1985

By Deverux M

Heavy mineral deposits accumulate on shorelines with interrupted sediment input. Beach deposits, which form on shallowly dipping coastal plains, are most favourable. However, shallow shelves seaward of cliffed coastlines are known to contain economic deposits. Significantgeologicalconditions are defined, from review of the stratigraphic and geomorphic controls on known deposits , for heavy mineral accumulation on the Swan Coastal Plain.

Jan 1, 1986

By Allnutt S. L, Carswell J. T, Mutton A. J

The Dugald River Zn-Pb-Ag deposit occurs within the complexly deformed and metamorphosed sediments of the Middle Proterozoic Cloncurry Terrane, Eastern Succession, Mount Isa Inlier. The sedimentary sequence comprises a thick package of variably carbonatic argillitic and siliciclastic sediments of the Corella Formation, Lady Clayre Dolomite and Knapdale Quartzite. A slate and calc-argillite unit locally referred to as the Dugald River Slates is the host to the economically significant deposit. The deformational history of the Dugald River area involved three phases of ductile deformation. The present geometry of the Dugald River Main Lode is recognised as a strike extensive steep westerly dipping tabular sheet, within which a steep north westerly plunging zone of pronounced thickening is evident. This zone is interpreted to have formed during folding via remobilisation of the sulphides into a shoot-like body, the geometry of which was controlled by stretching associated with the folding. Further modification of the shoot and sulphide re-distribution has resulted from late phase transgressive shears. The sulphide mineralisation is characterised by three distinctive sulphide types, laminated, banded and breccia, the distribution of which define two broad zones. The northern zone is a narrow I - 5 m thick stratabound unit comprising finely laminated and banded sulphide mineralisation within a well bedded fine grained argillite sequence. This is part of the Lady Clayre Dolomite sequence and is a predeformational precursor form of mineralisation. The southern zone comprises the thickest development of mineralisation (up to 30 m) characterised by slate-sulphide breccias and veins derived from complex polyphase remobilisation of the sulphide mineralisation. It is this zone which forms a stratabound locally transgressive body within the high strain Dugald River Slates and which contains the main body of economic mineralisation. Sulphide mineralogy comprises sphalerite, pyrite, pyrrhotite, galena and traces of chalcopyrite, pyrargyrite, tetrahedrite, marcasite and arsenopyrite. The present resource for the Dugald River deposit stands at 38 Mt grading 13.0 per cent Zn, 2.1 per cent Pb and 42 g/t AS. The Dugald River Zn-Pb-Ag deposit is regarded as an example of a syndiagenetic stratabound sulphide accumulation which, as the result of polyphase deformation and upper greenschist to middle amphibolite facies metamorphism, has undergone extensive remobilisation and Rccrystallisation.

Jan 1, 1993

By Johnson RD

The variation in coal properties and the coal seam reduced level can be analysed using partial trend-surface analysis techniques. For the area studied seam reduced level and seam thickness data from the Bulli Coal yield trend-surfaces with a high coefficient of determination, since they have relatively small systematic local and random components in their overall variation. Sulphur content appears to have no significant re.gi_onal trend, and phosphorus content has a very weak regional trend. Other analytical variables have regional trends which are of intermediate strength. The strike-directions of.the statistically significant first degree! trend-surface are similar, sug-gesting.: that the variation of the several coal properties was controlled by a set of- related causes. The relations apparent from the dip and strike of the first degree trend-surfaces are similar to- those which are apparent from the trend- surface residuals and'from the results' of canonical trend-surface analysis.'.. It is probable that differential subsidence controlled the areal

Jan 1, 1975

By Floyd JM

Pilot plant trials showed the effective ness of the submerged lance SIROSMELT technology for altering the composition of iron blast furnace slags as a preliminary step to produc- tion of formed materials. Mixtures of oil and air were injected into a bath of liquid slag to provide the heat required for melting the additives and to provide very turbulent conditions which resulted in complete dissol- ution of added fluorspar within one minute and almost complete dissolution of silica in two minutes. Sulphur lost during injection was readily made up by addition of pyrite or pyrrhotite. A stable foam could be readily made and broken down and the foamed slag appeared suitable for extrusion or forming into shapes.

Jan 1, 1979

The Argyle Diamond Mine came on stream late in 1985 as the world's largest diamond producer in terms of carat output. The design of the process plant, including the heavy medium separation (HMS) facility which provides the initial stages for separation of diamonds from gangue, evolved over a lengthy period of feasibility study and site investigation into the final form described in this paper. The commissioning was carefully planned and co-ordinated, and culminated successfully with handover of the plant on schedule and within budget. Problems encountered during .within were minimal and since then the plant has achieved greater than design throughput during its first year of operation. Darvr_ontmn

Jan 1, 1987

By Roderick W. F

The equipment and procedures used for green pellet production on a laboratory scale are given, together with a description of the straight grate pellet strand analogue which has been developed to examine the response of various ore types to heat hardening. The capabilities of the analogue are illustrated with data obtained from the balling and drying studies using a manganese ore. Differences in inter-batch pellet quality are discussed, and method of minimising the experimental error that can arise from these differences is Presented.

Jan 1, 1974

By Cairncross A. A

Papers on technical aspects of the Melbourne Underground Rail Loop project are being presented at this conference or have been presented previously or will be presented at other forums. This paper provides the framework for these papers by presenting the overall engineering tasks. The conceptual design, the special investigations undertaken, the management of the project and the construction development are highlighted.

Jan 1, 1981

An understanding of the importance of the different components that comprise a rock bolt unit is necessary to ensure the proper use of rock bolts as a means of roof support. The various anchors, bolts and plates in use in Australia have been designed and adapted for Australian con- ditions. As mining conditions change, so will the types of bolts in use. This is apparent in the development of chemical anchors and other recent innovations.

Jan 1, 1971

By McMullen P. H

Mining of copper ore at Mount Lyell has been continuous since 1893. The operation has always been marginal and the depressed copper Market over the last decade has seen mining continue on the basis of a series of short term plans. In 1985 it was determined that the mine would close in 1989 on completion of the 40 Series mining block. Significant changes in the value of the Australian dollar in 1986 and the subsequent effect on profitability dictated a review of the Company's operations. Lower level ore reserves, mining methods and ore handling systems were re-examined and a plan proposed for mining of the 50 and 60 Series mining blocks. The improved economics of this plan, together with workforce and State Government initiatives resulted in an extension of mine life to 1994.

Jan 1, 1988

By Channon W, Dube M, Makwana M, Kerfoot D. G

In early-1995, the Bindura Nickel Corporation commissioned a pressure leach plant at its Smelter and Refinery complex located in Bindura, Zimbabwe. The novel pressure leach process was developed by Sherritt to treat the nickel-copper sulphide residue produced from the original atmospheric leach circuit. The process extracts essentially all the nickel from the nickel-copper sulphide residue under non-oxidising acid pressure leach conditions, thereby producing an upgraded copper sulphide residue suitable for smelting and refining to electrolytic copper. The commissioning of the pressure leach plant was relatively smooth and design conditions were achieved within six weeks of operation. This paper presents a brief description of the process development and the plant design, followed by highlights of the plant start-up activities and summary of the plant performance.

Jan 1, 1996

By Anderson KG

Multi-seam mining under the western portion of Lake Macquarie NSW commenced in 1982. Up to three seams separated by partings ranging from 10 to 30 metres are mined simultaneously by Newcom Collieries. A feature of these workings is the minimal bedrock cover, which ranges from 130 metres down to only 40 metres. "Surface" subsidence control has an over-riding influence on the design of the workings. Subsidence considerations govern both the selection of the mining method and the dimensioning of the workings. To date, workings have been designed in accordance with the "Wardell Guidelines for Mining Under Tidal Waters". These guidelines are tabulated and evaluated in the light of advances in rock mechanics knowledge and local subsidence data collected since the Guidelines were formulated in 1974. The local and regional stability of shallow workings designed according to the Guidelines is evaluated.

Jan 1, 1986