Search Documents

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

Christmas Island contains large deposits of phosphate minerals varying from high-grade calcium-phosphate (apatite) to lower grade iron and'aluminium phosphate (crandallite/millisite). The surface material is dominantly C-grade (Fe/Al) phosphate profiling into B-grade, a variable mixture of C- and A-grade ores, before reaching the high A-grade phosphate (apatite) which overlies a limestone Karrenfeld Base formation. A-grade ore is the basic phosphate used for the manufacture of superphosphate and phosphoric acid, whilst B-grade contains amounts of iron and aluminium which are unacceptable for these acidulation processes. Research into methods of separating the finer iron and aluminium phosphates from the coarser calcium phosphates has led to the development of wash-screen processes enabling recovery of 50 to 60%, as A-grade phosphate. Developmental stages included laboratory investigations, mineralogical studies, pilot tests leading the initial 20 tph prototype production unit and the current 100 tph production wash/screen plant, commissioned early in 1970 at Christmas Island.

Jan 1, 1971

A short overview of the research program of SveBeFo, Swedish Rock Engineering Research, which was founded in 1993 is first given. Then four recent and ongoing projects in rock blasting and explosives engineering are presented in greater detail: 1. Burn Equations for Commercial Explosives. 2. Blast Damage in Contour Blasting. 3. The Role of Gas Pressure in Pit Wall Damage. 4. Fragmentation of Aggregate Rock. The goal of the bum equation project is to be able to control the energy release from explosive charges to the desired part of the expansion curve of the reaction products under various rock conditions. SveBeFo's work has reached the stage where a burn equation for a lab emulsion has been established which can model the influence of charge diameter on the VOD and detonation front curvature in a cylindrical charge quite well. This work now continues with other emulsion recipes. In the blast damage project the goal is to develop techniques and recommendations on how to minimise the blast damage in construction blasting. The project has gained extensive practical knowledge from the blasting of more than 200 holes in a granite quarry under controlled conditions. The cracks in the rock surrounding the contour holes have been cut open and measured. The influence of factors like charge concentration, decoupling ratio, hole and charge size, VOD and time delay in initiation have been investigated. A simultaneous initiation of a group of contour holes with EDD detonators is quite superior to single hole blasts, even when they are timed as closely as 1 ms.

Jan 1, 1995

In line with the recommendations of The AusIMM/AMIC Joint Committee Report in 1981 Isa Mine ore reserves are quoted in proven and probable categories (recoverable ore reserves). Internal reporting considers geological mining and extraction reserves in terms of proven and probable categories. Proven reserves are subdivided into detailed and confirmed ore. External reporting includes a possible ore category (not a reserve). The basis for these divisions is the spatial distribution of sampling data. Proven ore is defined by data 80m apart or less and probable ore by data 80m to 150m apart. Within the proven ore category detailed ore is defined by data 40m apart or less and confirmed ore by data 40m to 80m apart. Kriging is used to provide tonnage and grade information for the currently producing 1100 and 1900 orebodies. Kriged cross sections are initially produced to coincide with existing geological sections and are used for stope design. Stope ore reserves calculations are ideally performed at three discrete design stages, which in order of increasing accuracy are: preliminary design (PD), final design (FD) and ring design (RD). At each of these stages Kriged meshes incorporating the most recent sampling information are produced for reserve calculations. Historically derived mining and extraction factors are applied both to global reserves and individual stope reserves to reflect changes in geological and mining conditions as well as the sequencing of extraction. These factorised reserves are then inserted into the computerised reserves inventory system (RIN). Monitoring of individual stope performance continues into the production stage with input from planning, research, survey and production personnel. This allows actual extraction factors to be derived for comparison with predicted factors, providing some measure of stope performance.

Jan 1, 1987

China has abundant bauxite resources, but these resources are mostly of a diaspore, which has a feature of low Al2O3 to SiO2 mass ratio, typically ranging from four to six. Compared to other materials, this kind of raw materials consumes more alkaline and energy in the process of metallurgy, and incurred a high alumina production cost. To solve this problem, researchers in China have done a lot of work on removing of the silicon from bauxite. Under the impetus of these works, in 2003, the first flotation plant of diasporic bauxite in the world was constructed in Zhongzhou, Henan, China. Seven years of operating experience shows that this technology can signifi cantly reduce the costs of following-metallurgy processing. These efforts are an important reference for the processing of similar resource. In general, for Western scholars it is diffi cult to fully understand these works because most of them are published in Chinese. In this paper, a detail introduction for the research progress on China bauxite de-silica flotation was presented, these works involved crystal chemistry, wettability of bauxite minerals, collector and modifi er in bauxite fl otation and flotation practice, etc.

Sep 13, 2010

By J J. Frausto, G R. Ballantyne, M S. Powell, R Cruz, K Runge

Hydrocyclones are the most widely used device for classification in a grinding circuit. However, even the most efficient hydrocyclone has a bypass of fines from the feed to the underflow which reduces comminution circuit performance, as well as misclassification around the cut point. Fine screens classify only according to the particle size, allowing for a reduction in the recirculation of fines back to the mill. The development of high capacity multi-screens makes fine classification in a grinding circuit a viable option. Minera Saucito recently substituted hydrocyclones with screens in its grinding circuit. The change of classifier resulted in an increase in throughput and lead recovery but a decrease in silver recovery. This case study presents the changes in comminution and flotation performance that occurred after the installation of screens and uses historical operational data collected over 12 months of operation to investigate the reasons for these observed changes. CITATION:Frausto, J J, Ballantyne, G R, Runge, K, Powell, M S and Cruz, R, 2017., in Proceedings MetPlant 2017, pp 298–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Singh TN

Rampura-Agucha Zinc-Lead deposit is unique as it is reported for the first time in the gneissic terrain with a rich oregrade quality of early to middle Proterozoic of Bhilwara supracrustal belt in the Precambrian of Northwest India. These sulphide ores are mostly confined to the graphite bearing Quartzofelspathic gneisses with intermittent bands of Calc-Silicate granofels and amphibolite. The ore and country rock mineralogy and their textural features are indicative of highly metamorphosed deposit and further the presence of marmatite and monoclinic phyrrhotite revealed high temperature environment of deposition.The present paper deals with some of the ideas about the ore genesis and petrographics of the associated rocks for Rampura-Agucha Zinc-Lead deposits of Bhilwara District (Rajasthan).

Jan 1, 1990

By Skaviniak M

Some better perspectives applying to the exploitation and dressing of polymetallic ores in the Banskfa. gtiavnica-Hod- rusea Ore District are supposed to be achieved after a suc- cessful investigation and proving there the existence of deep-seated mineralization as well as due to increasing de- mand for non-ferrous metals and consequently to higher mar- ket prices of those recently noticed. With respect to the present situation in mining and to the further technical development as well, a several times higher exploitation may be in this region expected, especially in the deeper .eated parts of the deposit. When solving the tasks of a complex economic exploitation over the whole region, consi- derable attention is paid to regional relations and impact studies (due to expected exploitation and ore dressing but also to very difficult problems of dewatering (drainage pro- blems-). It will be first of all necessary to find there an equilibrium between the consequences resulting from the re- naissance of mining industry and environmental requests un- dispensable for the city of Banska 9tiavnica and the other neighbouring towns in the vicinity of mining plants.

Jan 1, 1988

Callide Coalfields produces a sub-bituminous, very subhydrous, low rank, steaming coal with good combustion properties, primarily for domestic power generation. Geological input into planning of coal extraction requires expedient production of detailed structural, lithological, analytical, geophysical and geotechnical data. The CSIRO-developed SIROLOG borehole logging software and hardware system allows for detailed spectrometric analysis of coal/interburden. The gamma-gamma and neutron-gamma SIROLOG techniques both provide improved prediction of ash content over other borehole techniques. The neutron-gamma technique also predicts density and some important ash constituents (especially iron, alumina and silica). The software/hardware configuration allows for quick, easy interpretation of coal seam depth and lithology, parting thickness and ash/ash constituent contents immediately after a borehole has been logged. Within certain mine areas in the Callide Basin, the iron content of mined coal is widely variable in both vertical and lateral extent within and between seams. This variability creates problems in predicting the slagging behaviour of æas-receivedÆ coal during combustion, especially where the iron content of the ash exceeds 19 per cent. Using the SIROLOG tool in co-operation with traditional borehole sample laboratory analysis results, patterns in this variability can be determined and related to geological properties and process of formation of the coal seams. Subsequently, areas of high iron can be predicted in advance of mining. Since 1992, on-going collection and interpretation of SIROLOG downhole geophysical log data has significantly contributed to a number of research projects related to gaining a preliminary understanding of the iron distribution and formation during the Coal MeasuresÆ deposition. Because the probe was able to record variations in coal mineral matter content, it was found to complement more conventional techniques such as reflected light petrography, X-Ray Diffraction and SEM techniques that examine the mineralogy of iron species. Additionally, software has been developed to allow integration of SIROLOG data into existing geology databases, enhancing coal quality modelling and daily prediction of parameters such as raw ash, silica and iron contents that are indicators of ash fusion propensity. The correlation of SIROLOG-derived iron geophysical traces between drillholes and other sample points highlighted lithological and structural controls in the iron distribution in the sequence previously not detected. This work has allowed the development of a methodology for predicting iron in advance of mining and reconciling as-sold coal quality to that predicted. Predictions are currently being assessed at the coal face as mining progresses through high-iron zones.

Jan 1, 2000

The control system of a mine winder or other variable speed drive has many component parts that must work together to provide the required functional performance of the machine, together with comprehensive safety features, reliability, maintainability, user-friendliness and efficiency. Modern winders use digital control technology extensively and hence software design is a major part of the overall system. It is not practical to simulate an entire mine winder in a single computer model because of the sheer mathematical complexity of the behaviour of many of the components. However, most component parts can be simulated quite easily, and related parts of the control system software can be simulated. Such simulations allow control software algorithms to be developed and tested in isolation from the real plant. Tests can be performed on the model without fear of injury to personnel or damage to the valuable plant. For example, speed regulator control algorithms and stability settings can be adjusted to and beyond the limits of stable operation, and near optimum settings can be found. This is particularly important, for example, when designing closed loop controls for emergency brake systems. Obviously, care must be taken to ensure that the computer model of the plant is realistic and takes into account as many non-linear features of the real plant as possible. Pure mathematical analysis of some systems is very difficult to perform when non-linear plant behaviour is involved. This paper shares a number of practical simulation experiences performed using commercially available software such as Matlab and Simulink to simulate various parts of the control system of a mine winder or other variable speed drive. Demonstrations of the operation of several different computer models are shown during the presentation of the paper.

Jan 1, 2005

By B Indraratna, A Dey

The surface geometry of a rock bolt plays a very important role in the rock/resin/bolt load transfer mechanism. Very little work has so far been reported on the influence of the bolt surface geometry on the bolt/resin interface failure mechanism. This paper examines the behaviour of bolt surface roughness under constant normal stiffness condition in the laboratory. To study the shear behaviour of the bolt/resin interface a series of shear tests with an initial normal stress between 0.1 to 7.5 MPa has been conducted on the flattened bolt surface of two most popular bolt types currently being used in Australia. Bolts with deeper ribs offered better shear resistance at low initial normal stress conditions whereas bolts with shallow and closer ribs offered better shear resistance at high normal stress conditions. The maximum dilation occurred at a shear displacement of 60 per cent of the rib spacing irrespective of the bolt type and depth of the rib.

Jan 1, 2000

By P Collins, C Sheriff

The Sand Queen gold mine is a typical Archaean narrow, high-grade gold quartz lode deposit within a shear hosted system. Initial mining during 1904 - 1948 produced 181 659 ounces of gold from 248 564 tonnes of ore milled at an average production grade of 22.7 g/t Au, which equates to a minimum of 750 ounces per vertical metre. The current mining operation is using the old Sand Queen main shaft to access the Sand George deposit, which is a narrow quartz lode system discovered in the same shear structure along strike to the south of the Sand Queen mine workings. Current underground resources contain 360 200 tonnes at a grade of 11.8 g/t Au for 136 500 ounces. Mining is scheduled to produce 20 000 ounces of gold annually. Re-opening of the Sand Queen mine and underground development of the Sand George lodes has revived several grade control issues relevant to a narrow, ænuggettyÆ gold lode mining environment. These include the dependence of assay grade of individual samples upon a number of factors, including how and where a sample is collected, how and where it is analysed, and how grade data is used to estimate an æaverageÆ grade. Ideally, the only way to achieve an acceptable estimate of ætrue gradeÆ is to mine and mill a large parcel of ore (eg >100 tonnes) from each lode or ore type. In a mining operation producing relatively small tonnages from a number of separate ænuggettyÆ gold lodes, availability of resources and operational constraints may preclude intensive sampling for predictive grade control. At the Sand Queen mine, one of the key issues has been to establish a reliable system for estimation of gold grade with which to reconcile milling data. Extensive use has been made of detailed geological data to understand the grade distribution within individual lodes and between lodes, so as not to rely solely on assay results.

Jan 1, 2008

By C Gypton

This paper gives some insights into what to look for when reviewing feasibility studies. The review by a third party is an important element of the risk management process and may be the last remaining opportunity to uncover errors, or identify and reduce project risks on paper before they are converted to financial disappointments, steel and concrete monuments to process failures or cost overruns. The mining industry has had a spotty record in the area of estimating initial capital costs and operational performance, even though the standard of feasibility studies is generally acknowledged to have improved in the last decades. Third party reviews rarely have the luxury of enough time and unlimited funds, so where should the reviewers focus their efforts to be most effective? Assuming that the project already apparently meets investment criteria, the authors suggest where and how to look among fundamental project parameters for signs that serious flaws exist that have the potential to become project killers. We also give advice on how to review cost estimates without becoming lost in the details. The paper is supported with numerous actual examples.

Jan 1, 2003

By Durucan S

The southern Attiki peninsula is a very interesting area from an environmental point of view. The port and the city of Lavrio is situated at the east coast of the peninsula with about 10 000 inhabitants and there are also a few villages in the vicinity. The south-eastern part of the peninsula hosts the famous Lavrio mines which exploited the silver bearing orebodies of the area for more than 25 centuries. As a result, soils around the city of Lavrio are polluted with high heavy metal loads. The area is also of archaeological interest, as there are well preserved remnants of ancient mining and processing plants and archaeological sites. Soil samples collected from an area of approximately 120 km2 around Lavrio were analysed for their metal contents and the spatial distribution of the concentrations of ten selected elements were estimated from these data sets. The spatial data analysis and transformation capabilities of Geographic Information Systems, combined with extensive mining and geological data, helped the authors to identify the extent and causes of metal pollution around Lavrio.

Jan 1, 1995

By Bond W. F, Sharry P. V, Onley P. G

The use of Decision Analysis is becoming more widespread in industry as a whole, and there is considerable scope for its application in the mining industry. Wherever decisions have to be made, whenever risks have to be taken, whenever uncertainty exists or whenever judgements have to be made, then Decision Analysis can be used. In the mining industry we daily make many decisions involving risk, uncertainty and judgement. Expansion and diversity will only increase the need for balanced decision making techniques. This paper seeks to describe the history and principles of Decision Theory, and to illustrate the various modelling approaches using three fictitious yet realistic case studies. Decision Analysis logically integrates the quantifiable and seemingly non-quantifiable aspects of a decision problem into a coherent, explicit and rational solution. It also allows the decision-makers to see the full impact of each variable or uncertainty, and hence focus on the key aspects that influence the solution.

Jan 1, 1996

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

By Wygralk A, Hallenstein CP

On a world scale, many Mid-Proterozoic fluvial sediments are prospective for low grade, large-tonnage gold deposits. A significant area of the Northern Territory is covered by such Mid-Proterozoic sediments, the gold potential of which has been barely tested. The geological knowledge of these sediments is summarised. The Westmoreland Conglomerate, the basal Mid-Proterozoic formation of the McArthur Basin, has been subjected to detailed sedimentological studies in order to determine the paleoenvironments and to assess the possibility of paleoplacer occurrences. The results indicate that the sandstones and conglomerates of the formation were deposited by braided rivers and debris flows as an alluvial fan which originated in source areas to the north east. The formation contains several upward-fining cycles of sedimentation, which are related to repeated periods of uplift in the source areas. The formation of placer-type gold occurrences is possible in such depositional environments. Very limited heavy mineral sampling has indicated a cassiterite- wolframite-gold suite in the sediments of the Westmoreland Conglomerate. Disconformities at the base of sedimentation cycles are deemed to be the most likely sites for large-tonnage paleoplacer concentrations.

Jan 1, 1984

By G J. Jameson, A Agarwal

This paper is concerned with the observation and analysis of bubble clusters in a laboratory flotation cell. A device was used in which bubbles were allowed to rise in clean water containing the same frother and collector concentration as in the cell. Bubble clusters were recorded using a high speed camera and analysed using an image analyser. Dodecyl amine was employed as a collector to float silica. The effect of impeller speed on the cluster behaviour was investigated. The results were interpreted in terms of cluster diameter and shape factor. The sizes of the bubbles forming the clusters were also measured and compared to the sizes of the independent bubbles in the cell. It was found that there was an optimum impeller speed in which the cluster diameter was a maximum. Higher agitation and the consequent higher power inputs resulted in cluster break-up while lower shear rates promoted cluster formation.

Jan 1, 2005

By T C. Souza Pinto, M Safari, F S. Hoseinian, D Deglon, L Leal Filhoc

In this study, the effect of hydrodynamic parameters on the iron ore reverse was investigated in a mechanical flotation cell. The work carries out using the case study of Iron ore from Vale in Brazil. The influence of hydrodynamic factors such as froth height, impeller speed, superficial gas velocity and solids percentage were evaluated on the quartz flotation. The results showed that the hydrodynamic conditions have a great effect on the flotation performance, especially on the fine and coarse quartz. The size-by-size analysis of the froth products showed that froth height, impeller speed, superficial gas velocity and solids percentage have a significant effect on true flotation quartz particles. The increase in the froth height decreased the recovery of quartz particles. The increase in the impeller speed increases the recovery of quartz particles to an optimum. The increase in the superficial gas velocity improved the flotation of coarse quartz particles. The increase in the solids percentage increases the recovery of quartz particles.

Sep 18, 2023

By Whittaker B. N, Reddish D. J

This paper presents the physical modelling results of subsurface fracture development associated with Iongwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results haióbeen obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camels. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992