Search Documents

Since the introduction of the Neil George Five Point Safety System, to the underground sections of The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines in March, 1969, the Disabling Injury Frequency Rate has been halved and shows signs of contin- uing to fall. The total accident frequency rate has also fallen, although the decrease has not been as significant. Before the introduction of the Neil George Safety System, analyses of the direct causes of accidents showed that approx- imately 25 per cent were caused by "unsafe conditions", while 75 per cent were attribu- table to "unsafe acts". Within twelve months of introducing the system, these percentages had significantly changed to 7 per cent unsafe conditions and 93 per cent unsafe acts. Today, the figures are 3 per cent and 97 per cent respectively, and these figures clearly show that the main emphasis in the current programme must be directed towards making the operating men safety conscious. The effort must be focused on changing the minds of men.

Jan 1, 1975

I would like to start by thanking The AusIMM and CSIRO for organising this excellent conference and inviting me to give a keynote address. Today I will focus on some broad observations of our industry, and leave the technical discussion to my colleagues who are presenting specific papers covering a wide range of topics. In preparation for this paper, I did a little research into the early history of the Pilbara iron ore industry. I was fascinated to read a quote attributed to Harry P Woodward, the Government Geologist in the late 19th century, before Federation. Mr Woodward described the Pilbara as an iron ore country and observed that æthere is enough to supply the whole world should the present sources be worked outÆ. Mr WoodwardÆs prediction could be viewed as wishful thinking and certainly at Hamersley Iron I would gladly envisage the Pilbara supplying the worldÆs entire iron ore needs! In reality, Western Australia accounted for 162 million tonnes or 36 per cent of seaborne trade in 2001. An impressive effort, but not quite the total world supply as Mr Woodward imagined. But we shouldnÆt dismiss these historical musings out of hand û perhaps we could see it as a challenge for the industry to æwork outÆ the present sources. We all know there is abundant iron ore in the Pilbara, and I expect it is only a matter of time until our collective technical expertise and sheer hard work will enable us to utilise its greater range of ore types. Opening up new markets will be a key pathway to creating additional value from the Pilbara ores. Today I will examine the state of play of our industry and the major influences that shape our business at present, before considering what the future might hold for us. I canÆt guarantee the accuracy of my crystal ball, but the stability and long-term nature of our industry does enable some reasonable hypotheses on where we are heading. I will also spend some time examining the way in which the iron ore producers are working to maximise the value of their resource base and obtain more from their existing capital assets.

Jan 1, 2002

By L Yao, J Li, C Sammut, B Li

The underground mine environment is inherently complex and hazardous, which necessitates ensuring mining workers’ safety. With the fast development of AI techniques, human activity recognition has become a crucial task to enhance daily life, especially in such challenging settings. This enables automatic monitoring and detection of the mine workers’ activities and operations on a large scale, which leads to better support of workers’ safety and welfare. Existing traditional uni-modal approaches, which use data of one single modality, suffer from low data quality and noise, so they struggle to generalise effectively in such extreme conditions (Li et al, 2022). As underground mines have extreme and complicated environments, such as dust, low light, signal interference, and rugged terrain, uni-modal approaches could not resolve such obstacles and are not suitable for real-world deployment. Multi-modal human activity recognition approaches could use data from multi-modal sources, thus capturing complementary information and producing robust and effective performance in recognising and monitoring mining activities. In this case, designing suitable multi-sensor hardware and AI activity recognition models has become a pivotal task. Producing efficient multi-modal approaches for edge deployment is another problem worth exploring.

Sep 1, 2024

By K Voigt, B Bolton, C Rumble

The Ok Tedi copper and gold mine is owned and operated by Ok Tedi Mining Limited (OTML) and is located in the Star Mountains of the Western Province of Papua New Guinea. Waste materials (both sulfidic and carbonate materials) from mining operations, comprising 55 Mt of waste rock and 31 Mt of tailings per annum, are discharged into the headwaters of mine area creeks where erosion and sediment transport carries significant proportions of the total waste into the Ok Tedi and Fly River systems. The tailings are potentially acid forming (PAF) while the waste rock has been strongly acid consuming with an excess of acid neutralising capacity (ANC) due to the high proportion of limestone waste. Tailings and waste rock are eroded into the river system and transported to the lower Ok Tedi and floodplains where deposition takes place. Because of concern due to vegetation die back, a dredging operation commenced in March 1998 to remove the sand fraction from the main river channel. OTML identified a potential future ARD risk from the stockpiled sands due to reduce limestone production at the mine and sulfide/carbonate mineral segregation in the river system and in the dredge sand stockpiles. This paper describes the structure and framework of an empirical model developed to assist OTML in planning ongoing mining operations to control ARD. Modelling identified the need to provide additional mined limestone to prevent future ARD generation from material deposited in the mine area creeks. With the additional limestone, the ARD risk in waste rock storage areas and in the Ok Tedi and Fly River sediments is predicted to remain low due to the combined effects of high ANC, high alkalinity of natural waters and high moisture contents (mostly fully water saturated). However, monitoring and modelling indicate that the ARD risk from the stockpiled sands will increase substantially during the remaining years of the operation. OTML have initiated programs to identify and evaluate options to mitigate this risk.

Jan 1, 2003

By Munive L

As a result of commissioning No.5 B F, 2670m3 inner volume, in March 1972, the largest B F in Australia; new expertise in maintenance, furnace operating practices and design have been obtained. This experience has also been extended to the other furnaces. A series of operating problems were con- fronted; all parts of the furnace, including the hearth side walls and bottom,were adversely affected. In December 1977, serious hearth wall wear was detected at No.5 B F, and a potential hearth breakout was averted. Hearth wear in No.4 B F was discovered in March 1979, and emer- gency underhearth cooling was installed to reverse an extremely advanced hearth bottom erosion. Hearth behaviour of No.5 B F oampaign 1972-1978 and`No.4 B F campaign commencing 1972, has been studied and discussions on the causes, effects and measures undertaken to protect the hearths are presented in this paper.

Jan 1, 1981

By Umar N

Traditional exploration has been undertaken by both local and overseas experts to discover tin deposits in Indonesia over almost 300 years. Indonesia is part of a tin belt which runs from Myanmar in the north through Malaysia to Singkep, Bangka, and Belitung islands in Indonesia in the south. The discovery of alluvial tin deposits is becoming harder as the more obvious geological targets are exhausted and topographical conditions become more difficult. New approaches are required to sustain successful exploration. There are indications that tin deposits can be found at depth on-shore as well as off-shore. These deposits are found associated with tough clays. On-shore tin exploration is hampered by swampy areas, while the off-shore search is often affected by difficult sea conditions. These factors lead to increases in the cost of exploration as well as the cost of subsequent production. Tin price fluctuations and environmental issues are also of major concern in the planning of the future operation of tin mining in Indonesia.

Jan 1, 1996

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

By M D. Rosengren, G Gregor, M F. Young

Over the last 15 years the silver/lead/zinc ore treated at Mount Isa became increasingly complex and lower grade. Metal recoveries dropped dramatically, causing a serious decline in profitability. The ætraditionalÆ response of increasing tonnage to reduce unit cost was unsuccessful, since the additional tonnage was even lower quality ore. A major technical and capital program in the 1990s restored metallurgical performance, but business return was still too low and ore quality continued to decline. In 1996 a new, holistic approach integrated the steps of geology, mining, concentrating, smelting, and refining. Previous assumptions about æfixedÆ and æmarginalÆ costs in mining and processing were shown to be wrong. Detailed analysis showed that some ore sources were reducing profit. This led to a fundamental redesign and downsizing of both Mount Isa and Hilton mines. The result was dramatic increases in head grades, metallurgical performance and plant stability without any capital expenditure. The business is now smaller, but more profitable.

Jan 1, 1998

The Vertical Crater Retreat (VCR) mining method was used to mine two rib pillars at New Broken Hill Consolidated Limited (NEHC) mine at Broken Hill. Experience gained in a trial VCR pillar stope was applied to the design of Panel 3CN pillar (P3CN). Restricted access and a central sandfilled plug in this pillar necessitated the use of angled blastholes and blasting of the stope in two sections. Borehole surveys and close charging supervision were necessary to block, charge and stem the spherical charges in the correct position. The laver sections of the VCR stope with rock walls attained an average slice advance of 2.2 m whereas the higher section of the st.ope between cemented fill walls attained an average slice advance of 3.4 m. Achieved fragmentation was extremely fine. External dilution was assessed at less than 10 per cent. A cement consolidated sandfill exposure of approximately 1300 m2 stood vertically with no significant slumping.

Jan 1, 1983

Investment decisions in the Australian mining industry are often made without awareness of the impact of risk on project outcomes. A fundamental change in thinking is required to move away from the traditional attitude of æcushioning the blowÆ towards a measured approach to project risk. Such an approach involves quantifying and understanding project uncertainty so that investments may be shielded from downside risk while at the same time exposed to upside potential. Communication and collaboration between study teams and corporate financial managers must be improved before the industry can improve its project investment record. Monte-Carlo simulation provides a way to quantify and understand investment risk, but its accuracy depends on how well the variability of input parameters is estimated. Research in this area is currently centred on quantifying uncertainty in mineral resource estimation using new conditional simulation techniques, but a less-rigorous method can be applied in practice to begin the education process and develop the required awareness at board level.

Jan 1, 2003

By Coronel PT

Like companies in other sectors of industry, mining companies are experiencing significant problems with low labour productivity, high labour turnover, and accidents. Increasingly, companies are recognising that good training is a vital factor in dealing with these problems. One such company is Aberfoyle Tin Limited. Early in 1979 the company engaged P.A. Consulting Services Pty. Ltd. (P.A.) to upgrade and formalize its miner training procedures. P.A. developed a programme using their Process Analysis Method of Training (P.A.M.T.) and trained a company trainer in its use. As a result of its application and the establishment of a formal training school, the rate of production of trained miners has been greatly increased. Despite some problems caused by lack of resources at the mine, the trainees graduating under the new scheme have been shown to be of comparable standard to those produced by the previously used "on the job" training method.

Jan 1, 1980

By H Kundapen, J J, C Rumble, S Miller

This paper describes measures taken by Ok Tedi Mining Limited (OTML) to minimise the risk of acid rock drainage (ARD) resulting from mining operations at its Mt Fubilan porphyry copper-gold mine in the remote Star Mountains of Papua New Guinea. The risk of acid generation and metal leaching as a result of oxidation of these sulfidic deposits has long been recognised by OTML. In 1998, OTML instigated the ARD Management Program to fully evaluate these risks and to formulate, if necessary, trial and implement appropriate management strategies. In implementing the ARD Management Program, OTML has adopted a risk management approach consisting of five stages: risk identification, risk analysis, risk assessment, risk treatment, and review and monitor. Significant progress has been made in relation to risk identification, analysis and assessment. The work currently underway to put in place a comprehensive risk treatment and review process will ultimately determine the success or otherwise of this approach.

Jan 1, 2003

Electronic Detonators have made significant strides over the last few years, both in quality of product and performance in different blast applications. The precision and flexibility of the SMARTDET units provides the mines with a powerful means of controlling blast results, giving both cost and productivity improvements. The SMARTDET Electronic Detonator System, robust and easy to use, has been successfully deployed over the last 18 months in improving mine productivity and creating safer working conditions in both quarrying and long-hole stoping. The key to the improvements has been the precision and flexibility of the electronic timing, and the ability of the mine personnel to grasp the concept quickly and use it effectively.

Jan 1, 1999

Australian mining practice operates at the forefront of technology. In recent times Australian designers, contractors and operators have shown many examples of technical "entrepreneurship" in solving geological mining and metallurgical problems. Developments have occurred in the fields of equipment, processing, operating techniques and training which have relevance to the mining industry in other countries. Our mineral exports play a key role in main- taining the viability of the Australian economy. Although the export potential of our specialised equipment and technology is at a much lower level it is a growth area. The export of our mining technology can continue to be basically the result of individual efforts but the question of whether it would be war- ranted and desirable, to establish a coordinating structure should be examined. Existing and new initiatives by the Federal Government indi- cate the Government's interest in the export of technology. The mining industry should take a proactive role formulating policy and programs within its technical jurisdiction.

Jan 1, 1988

In the humid, subtropical climatic conditions, typical of Papua New Guinean high-lands, auriferous carbonate-quartz lodes and stockwork veins of the Upper Ridges mine at Wau, have weathered in situ forming manganese dioxide-quartz wad flatmakes and veins. Vein assemblages and sulphidized host breccia have been chemically weathered to 20-25m depth, and microscopic grains of electrum (550-600 fine) formerly enclosed in carbonate, sulphide and quartz have dissolved in the oxidizing alkaline fluid. Coarse secondary electrum, crystalline and dendritic, is concentrated by manganese dioxide and at the base of chemical weathering. Fineness is unchanged, eliminating the possibility of gold and silver migration as a chloride complex. Experimental tests on the stability of thiosulphate, and its ability to dissolve gold and silver from colloid, crystal and synthetic alloy confirm that secondary electrum at Upper Ridges is most compatible with precipitation from (Au,Ag)(S203)23-; a complex readily destabilized in the presence of MnO., or with decreasing Eh.

Jan 1, 1984

Over the past decade most, if not all participants in the resources sector have been involved in initiatives to improve margins, reduce costs and improve business profitability. In many cases the initiatives undertaken have fallen short of their stated objectives, and in some cases have resulted in the terminal decline of the underlying business. In reviewing why many such initiatives fail, a common theme of arbitrary cost reduction and a focus on minimising cost as opposed to maximising value and cashflow emerges. This paper proposes a structured process that allows mine owners and managers to develop an understanding of their cost structure and optimise production and cost outcomes from the business. The broad objective of cost optimisation is to create value by getting more out of existing and new assets by focussing on operational areas, particularly production and maintenance. The paper uses practical examples to highlight the application of cost driver trees as a mine improvement tool.

Jan 1, 2002

By Shinnosuke U, Zhang HE

In this paper, it is shown that the higher the pre-activation concentration of copper ions in pulp, the larger the adsorption amounts of copper ions and xanthate on arsenopyrite surface, and the better the arsenopyrite flotability in strong alkaline medium. On arsenopyrite pre-activated with cupric ions, the xanthate adsorption density in strong alkaline medium is approximately equivalent to that of cupric ions. It is therefore concluded that an amount of copper ions adsorb on arsenopyrite surface first, and then an amount of xanthate can (and only can) adsorb dependently on the surface active sites produced by these adsorbed copper ions on the mineral, so that arsenopyrite is kept rather flotable and is hardly separated from pyrite even in very strong alkaline medium. Selectively wiping out the surface copper active sites on arsenopyrite is the key point of successful separation of pyrite from arsenopyrite. According to this theory, a new 'SZLI' (know-how) method was recommended to satisfactorily deal with the difficult separation.

Jan 1, 1993

The present-day arrangement of old ( ? ) Palaeozoic and Mesozoic metamorphic rocks in eastern New Guinea lends some support to the concept of tens:konal dilation in Upper Cretaceous to Lower Tertiary time, It appears that the metamorphic core of the Morobe Arc (Glaessner, 1950) could have been rifted from the eastern flank of Cape York Peninsula, and then been carried north-eastward by some unspecified sub-crustal. tangential force. In the early stages of the rift it is thought.that submarine basalts may have extruded up the .'tension .scar and spread across the floor of the opening rift. Thick clastic muddy sediments derived almost exclusively from the rifted block were then spread across the floor of the opening rift. Later ~ertiary lateral movements from east to west along the Markham-Ramu Fault appear to have bent the northern end of the Morobe Arc towards the.east,,causing the intense folding in the sediments of the Aure Trough.

Jan 1, 1962

By S G. Gatehouse

Extensive gold mining activity û dominantly alluvial û has taken place in the Sofala-Wattle Flat district since the 1850s.This work will have located most, if not all, of the visible sources for the gold in current stream systems.Also, there are many gold bearing elevated Tertiary alluvial terraces in the district which may confuse possible gold signals from primary hard rock sources in the streams.Associated element signatures eg As and other chalcophiles, will discriminate non-alluvial signatures but will not necessarily distinguish non gold bearing mineralisation.Both trace elements and conventional gold analyses will dominantly re-identify known occurrences. Conventional BCL sampling is considered misleading as experience from the Oberon area to the south of Sofala demonstrated that BCL sampling was very sensitive û perhaps too sensitive.All occurrences û major or minor û of gold will be detected (Gatehouse, 1992). To improve on BCL sampling, a small, -120# sample with selective duplication was recommended to screen coarse-grained gold anomalism and a program of sampling covering an area thought to be prospective was enacted.Samples returning anomalous Au were analysed in duplicate and if the results demonstrated reproducibility, indicating fine gold only, the sample site was assigned a high priority.It was found that most of the reproducible samples clustered in one area û Spring Gully. The results of this sampling program led to immediate identification and, ultimately, the successful delineation of the Spring Gully gold deposit near Wattle Flat.

Jan 1, 2004